diff options
Diffstat (limited to 'libraries/Wire/examples')
6 files changed, 239 insertions, 0 deletions
diff --git a/libraries/Wire/examples/SFRRanger_reader/SFRRanger_reader.pde b/libraries/Wire/examples/SFRRanger_reader/SFRRanger_reader.pde new file mode 100755 index 0000000..c89b0f0 --- /dev/null +++ b/libraries/Wire/examples/SFRRanger_reader/SFRRanger_reader.pde @@ -0,0 +1,84 @@ +// I2C SRF10 or SRF08 Devantech Ultrasonic Ranger Finder +// by Nicholas Zambetti <http://www.zambetti.com> +// and James Tichenor <http://www.jamestichenor.net> + +// Demonstrates use of the Wire library reading data from the +// Devantech Utrasonic Rangers SFR08 and SFR10 + +// Created 29 April 2006 + +#include <Wire.h> + +void setup() +{ + Wire.begin(); // join i2c bus (address optional for master) + Serial.begin(9600); // start serial communication at 9600bps +} + +int reading = 0; + +void loop() +{ + // step 1: instruct sensor to read echoes + Wire.beginTransmission(112); // transmit to device #112 (0x70) + // the address specified in the datasheet is 224 (0xE0) + // but i2c adressing uses the high 7 bits so it's 112 + Wire.send(0x00); // sets register pointer to the command register (0x00) + Wire.send(0x50); // command sensor to measure in "inches" (0x50) + // use 0x51 for centimeters + // use 0x52 for ping microseconds + Wire.endTransmission(); // stop transmitting + + // step 2: wait for readings to happen + delay(70); // datasheet suggests at least 65 milliseconds + + // step 3: instruct sensor to return a particular echo reading + Wire.beginTransmission(112); // transmit to device #112 + Wire.send(0x02); // sets register pointer to echo #1 register (0x02) + Wire.endTransmission(); // stop transmitting + + // step 4: request reading from sensor + Wire.requestFrom(112, 2); // request 2 bytes from slave device #112 + + // step 5: receive reading from sensor + if(2 <= Wire.available()) // if two bytes were received + { + reading = Wire.receive(); // receive high byte (overwrites previous reading) + reading = reading << 8; // shift high byte to be high 8 bits + reading |= Wire.receive(); // receive low byte as lower 8 bits + Serial.println(reading); // print the reading + } + + delay(250); // wait a bit since people have to read the output :) +} + + +/* + +// The following code changes the address of a Devantech Ultrasonic Range Finder (SRF10 or SRF08) +// usage: changeAddress(0x70, 0xE6); + +void changeAddress(byte oldAddress, byte newAddress) +{ + Wire.beginTransmission(oldAddress); + Wire.send(0x00); + Wire.send(0xA0); + Wire.endTransmission(); + + Wire.beginTransmission(oldAddress); + Wire.send(0x00); + Wire.send(0xAA); + Wire.endTransmission(); + + Wire.beginTransmission(oldAddress); + Wire.send(0x00); + Wire.send(0xA5); + Wire.endTransmission(); + + Wire.beginTransmission(oldAddress); + Wire.send(0x00); + Wire.send(newAddress); + Wire.endTransmission(); +} + +*/ diff --git a/libraries/Wire/examples/digital_potentiometer/digital_potentiometer.pde b/libraries/Wire/examples/digital_potentiometer/digital_potentiometer.pde new file mode 100644 index 0000000..35ee5d6 --- /dev/null +++ b/libraries/Wire/examples/digital_potentiometer/digital_potentiometer.pde @@ -0,0 +1,34 @@ +// I2C Digital Potentiometer +// by Nicholas Zambetti <http://www.zambetti.com> +// and Shawn Bonkowski <http://people.interaction-ivrea.it/s.bonkowski/> + +// Demonstrates use of the Wire library +// Controls AD5171 digital potentiometer via I2C/TWI + +// Created 31 March 2006 + +#include <Wire.h> + +void setup() +{ + Wire.begin(); // join i2c bus (address optional for master) +} + +byte val = 0; + +void loop() +{ + Wire.beginTransmission(44); // transmit to device #44 (0x2c) + // device address is specified in datasheet + Wire.send(0x00); // sends instruction byte + Wire.send(val); // sends potentiometer value byte + Wire.endTransmission(); // stop transmitting + + val++; // increment value + if(val == 64) // if reached 64th position (max) + { + val = 0; // start over from lowest value + } + delay(500); +} + diff --git a/libraries/Wire/examples/master_reader/master_reader.pde b/libraries/Wire/examples/master_reader/master_reader.pde new file mode 100644 index 0000000..1b139de --- /dev/null +++ b/libraries/Wire/examples/master_reader/master_reader.pde @@ -0,0 +1,29 @@ +// Wire Master Reader +// by Nicholas Zambetti <http://www.zambetti.com> + +// Demonstrates use of the Wire library +// Reads data from an I2C/TWI slave device +// Refer to the "Wire Slave Sender" example for use with this + +// Created 29 March 2006 + +#include <Wire.h> + +void setup() +{ + Wire.begin(); // join i2c bus (address optional for master) + Serial.begin(9600); // start serial for output +} + +void loop() +{ + Wire.requestFrom(2, 6); // request 6 bytes from slave device #2 + + while(Wire.available()) // slave may send less than requested + { + char c = Wire.receive(); // receive a byte as character + Serial.print(c); // print the character + } + + delay(500); +} diff --git a/libraries/Wire/examples/master_writer/master_writer.pde b/libraries/Wire/examples/master_writer/master_writer.pde new file mode 100644 index 0000000..d0ff9fa --- /dev/null +++ b/libraries/Wire/examples/master_writer/master_writer.pde @@ -0,0 +1,28 @@ +// Wire Master Writer +// by Nicholas Zambetti <http://www.zambetti.com> + +// Demonstrates use of the Wire library +// Writes data to an I2C/TWI slave device +// Refer to the "Wire Slave Receiver" example for use with this + +// Created 29 March 2006 + +#include <Wire.h> + +void setup() +{ + Wire.begin(); // join i2c bus (address optional for master) +} + +byte x = 0; + +void loop() +{ + Wire.beginTransmission(4); // transmit to device #4 + Wire.send("x is "); // sends five bytes + Wire.send(x); // sends one byte + Wire.endTransmission(); // stop transmitting + + x++; + delay(500); +} diff --git a/libraries/Wire/examples/slave_receiver/slave_receiver.pde b/libraries/Wire/examples/slave_receiver/slave_receiver.pde new file mode 100644 index 0000000..53c86b5 --- /dev/null +++ b/libraries/Wire/examples/slave_receiver/slave_receiver.pde @@ -0,0 +1,35 @@ +// Wire Slave Receiver +// by Nicholas Zambetti <http://www.zambetti.com> + +// Demonstrates use of the Wire library +// Receives data as an I2C/TWI slave device +// Refer to the "Wire Master Writer" example for use with this + +// Created 29 March 2006 + +#include <Wire.h> + +void setup() +{ + Wire.begin(4); // join i2c bus with address #4 + Wire.onReceive(receiveEvent); // register event + Serial.begin(9600); // start serial for output +} + +void loop() +{ + delay(100); +} + +// function that executes whenever data is received from master +// this function is registered as an event, see setup() +void receiveEvent(int howMany) +{ + while(1 < Wire.available()) // loop through all but the last + { + char c = Wire.receive(); // receive byte as a character + Serial.print(c); // print the character + } + int x = Wire.receive(); // receive byte as an integer + Serial.println(x); // print the integer +} diff --git a/libraries/Wire/examples/slave_sender/slave_sender.pde b/libraries/Wire/examples/slave_sender/slave_sender.pde new file mode 100644 index 0000000..f500644 --- /dev/null +++ b/libraries/Wire/examples/slave_sender/slave_sender.pde @@ -0,0 +1,29 @@ +// Wire Slave Sender +// by Nicholas Zambetti <http://www.zambetti.com> + +// Demonstrates use of the Wire library +// Sends data as an I2C/TWI slave device +// Refer to the "Wire Master Reader" example for use with this + +// Created 29 March 2006 + +#include <Wire.h> + +void setup() +{ + Wire.begin(2); // join i2c bus with address #2 + Wire.onRequest(requestEvent); // register event +} + +void loop() +{ + delay(100); +} + +// function that executes whenever data is requested by master +// this function is registered as an event, see setup() +void requestEvent() +{ + Wire.send("hello "); // respond with message of 6 bytes + // as expected by master +} |