2 files changed, 0 insertions, 148 deletions
diff --git a/libraries/SoftwareSerial/examples/SoftwareSerialExample/SoftwareSerialExample.ino b/libraries/SoftwareSerial/examples/SoftwareSerialExample/SoftwareSerialExample.ino
deleted file mode 100644
index 6101bb1..0000000
--- a/libraries/SoftwareSerial/examples/SoftwareSerialExample/SoftwareSerialExample.ino
+++ /dev/null
@@ -1,55 +0,0 @@
-/*
-  Software serial multple serial test
- 
- Receives from the hardware serial, sends to software serial.
- Receives from software serial, sends to hardware serial.
- 
- The circuit: 
- * RX is digital pin 10 (connect to TX of other device)
- * TX is digital pin 11 (connect to RX of other device)
- 
- Note:
- Not all pins on the Mega and Mega 2560 support change interrupts, 
- so only the following can be used for RX: 
- 10, 11, 12, 13, 50, 51, 52, 53, 62, 63, 64, 65, 66, 67, 68, 69
- 
- Not all pins on the Leonardo support change interrupts, 
- so only the following can be used for RX: 
- 8, 9, 10, 11, 14 (MISO), 15 (SCK), 16 (MOSI).
- 
- created back in the mists of time
- modified 25 May 2012
- by Tom Igoe
- based on Mikal Hart's example
- 
- This example code is in the public domain.
- 
- */
-#include <SoftwareSerial.h>
-
-SoftwareSerial mySerial(10, 11); // RX, TX
-
-void setup()  
-{
-  // Open serial communications and wait for port to open:
-  Serial.begin(57600);
-  while (!Serial) {
-    ; // wait for serial port to connect. Needed for Leonardo only
-  }
-
-
-  Serial.println("Goodnight moon!");
-
-  // set the data rate for the SoftwareSerial port
-  mySerial.begin(4800);
-  mySerial.println("Hello, world?");
-}
-
-void loop() // run over and over
-{
-  if (mySerial.available())
-    Serial.write(mySerial.read());
-  if (Serial.available())
-    mySerial.write(Serial.read());
-}
-
diff --git a/libraries/SoftwareSerial/examples/TwoPortReceive/TwoPortReceive.ino b/libraries/SoftwareSerial/examples/TwoPortReceive/TwoPortReceive.ino
deleted file mode 100644
index d607ee6..0000000
--- a/libraries/SoftwareSerial/examples/TwoPortReceive/TwoPortReceive.ino
+++ /dev/null
@@ -1,93 +0,0 @@
-/*
-  Software serial multple serial test
- 
- Receives from the two software serial ports, 
- sends to the hardware serial port. 
- 
- In order to listen on a software port, you call port.listen(). 
- When using two software serial ports, you have to switch ports
- by listen()ing on each one in turn. Pick a logical time to switch
- ports, like the end of an expected transmission, or when the 
- buffer is empty. This example switches ports when there is nothing
- more to read from a port
- 
- The circuit: 
- Two devices which communicate serially are needed.
- * First serial device's TX attached to digital pin 2, RX to pin 3
- * Second serial device's TX attached to digital pin 4, RX to pin 5
- 
- Note:
- Not all pins on the Mega and Mega 2560 support change interrupts, 
- so only the following can be used for RX: 
- 10, 11, 12, 13, 50, 51, 52, 53, 62, 63, 64, 65, 66, 67, 68, 69
- 
- Not all pins on the Leonardo support change interrupts, 
- so only the following can be used for RX: 
- 8, 9, 10, 11, 14 (MISO), 15 (SCK), 16 (MOSI).
- 
- created 18 Apr. 2011
- modified 25 May 2012
- by Tom Igoe
- based on Mikal Hart's twoPortRXExample
- 
- This example code is in the public domain.
- 
- */
-
-#include <SoftwareSerial.h>
-// software serial #1: TX = digital pin 10, RX = digital pin 11
-SoftwareSerial portOne(10,11);
-
-// software serial #2: TX = digital pin 8, RX = digital pin 9
-// on the Mega, use other pins instead, since 8 and 9 don't work on the Mega
-SoftwareSerial portTwo(8,9);
-
-void setup()
-{
- // Open serial communications and wait for port to open:
-  Serial.begin(9600);
-   while (!Serial) {
-    ; // wait for serial port to connect. Needed for Leonardo only
-  }
-
-
-  // Start each software serial port
-  portOne.begin(9600);
-  portTwo.begin(9600);
-}
-
-void loop()
-{
-  // By default, the last intialized port is listening.
-  // when you want to listen on a port, explicitly select it:
-  portOne.listen();
-  Serial.println("Data from port one:");
-  // while there is data coming in, read it
-  // and send to the hardware serial port:
-  while (portOne.available() > 0) {
-    char inByte = portOne.read();
-    Serial.write(inByte);
-  }
-
-  // blank line to separate data from the two ports:
-  Serial.println();
-
-  // Now listen on the second port
-  portTwo.listen();
-  // while there is data coming in, read it
-  // and send to the hardware serial port:
-  Serial.println("Data from port two:");
-  while (portTwo.available() > 0) {
-    char inByte = portTwo.read();
-    Serial.write(inByte);
-  }
-
-  // blank line to separate data from the two ports:
-  Serial.println();
-}
-
-
-
-
-
-