Remove non-USB boards

Removes boards from boards.txt, bootloaders for those boards, and variants for those boards. As none of these boards support USB there's no reason to keep them around.

1 files changed, 0 insertions, 587 deletions

diff --git a/bootloaders/stk500v2/Makefile b/bootloaders/stk500v2/Makefile
deleted file mode 100644
index eeb9add..0000000
--- a/bootloaders/stk500v2/Makefile
+++ /dev/null
@@ -1,587 +0,0 @@
-# ----------------------------------------------------------------------------

-# Makefile to compile and link stk500boot bootloader

-# Author: Peter Fleury

-# based on WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al.

-#

-# Adjust F_CPU below to the clock frequency in Mhz of your AVR target

-# Adjust BOOTLOADER_ADDRESS to your AVR target

-#

-#----------------------------------------------------------------------------

-# On command line:

-#

-# make all = Make software.

-#

-# make clean = Clean out built project files.

-#

-# make coff = Convert ELF to AVR COFF.

-#

-# make extcoff = Convert ELF to AVR Extended COFF.

-#

-# make program = Download the hex file to the device, using avrdude.

-#                Please customize the avrdude settings below first!

-#

-# make debug = Start either simulavr or avarice as specified for debugging, 

-#              with avr-gdb or avr-insight as the front end for debugging.

-#

-# make filename.s = Just compile filename.c into the assembler code only.

-#

-# make filename.i = Create a preprocessed source file for use in submitting

-#                   bug reports to the GCC project.

-#

-# To rebuild project do "make clean" then "make all".

-#----------------------------------------------------------------------------

-#	<MLS> = Mark Sproul msproul-at-skychariot.com

-

-

-# MCU name

-#MCU = atmega128

-

-

-# Processor frequency.

-#     This will define a symbol, F_CPU, in all source code files equal to the 

-#     processor frequency. You can then use this symbol in your source code to 

-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done

-#     automatically to create a 32-bit value in your source code.

-#F_CPU = 16000000

-

-

-# Bootloader

-# Please adjust if using a different AVR

-# 0x0e00*2=0x1C00 for ATmega8  512 words Boot Size

-# 0xFC00*2=0x1F800 for ATmega128  1024 words Boot Size

-# 0xF800*2=0x1F000 for ATmega1280

-# 0xF000*2=0x1E000 for ATmega1280

-#BOOTLOADER_ADDRESS = 1E000

-

-

-# Output format. (can be srec, ihex, binary)

-FORMAT = ihex

-

-

-# Target file name (without extension).

-TARGET = stk500boot

-

-

-# List C source files here. (C dependencies are automatically generated.)

-SRC = stk500boot.c 

-

-

-# List Assembler source files here.

-#     Make them always end in a capital .S.  Files ending in a lowercase .s

-#     will not be considered source files but generated files (assembler

-#     output from the compiler), and will be deleted upon "make clean"!

-#     Even though the DOS/Win* filesystem matches both .s and .S the same,

-#     it will preserve the spelling of the filenames, and gcc itself does

-#     care about how the name is spelled on its command-line.

-ASRC = 

-

-

-# Optimization level, can be [0, 1, 2, 3, s]. 

-#     0 = turn off optimization. s = optimize for size.

-#     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)

-OPT = s

-

-

-# Debugging format.

-#     Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs.

-#     AVR Studio 4.10 requires dwarf-2.

-#     AVR [Extended] COFF format requires stabs, plus an avr-objcopy run.

-DEBUG = dwarf-2

-

-

-# List any extra directories to look for include files here.

-#     Each directory must be seperated by a space.

-#     Use forward slashes for directory separators.

-#     For a directory that has spaces, enclose it in quotes.

-EXTRAINCDIRS = 

-

-

-# Compiler flag to set the C Standard level.

-#     c89   = "ANSI" C

-#     gnu89 = c89 plus GCC extensions

-#     c99   = ISO C99 standard (not yet fully implemented)

-#     gnu99 = c99 plus GCC extensions

-CSTANDARD = -std=gnu99

-

-

-# Place -D or -U options here

-CDEFS = -DF_CPU=$(F_CPU)UL

-

-

-# Place -I options here

-CINCS =

-

-

-

-#---------------- Compiler Options ----------------

-#  -g*:          generate debugging information

-#  -O*:          optimization level

-#  -f...:        tuning, see GCC manual and avr-libc documentation

-#  -Wall...:     warning level

-#  -Wa,...:      tell GCC to pass this to the assembler.

-#    -adhlns...: create assembler listing

-CFLAGS = -g$(DEBUG)

-CFLAGS += $(CDEFS) $(CINCS)

-CFLAGS += -O$(OPT)

-CFLAGS += -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums -fno-jump-tables

-CFLAGS += -Wall -Wstrict-prototypes

-CFLAGS += -Wa,-adhlns=$(<:.c=.lst)

-CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))

-CFLAGS += $(CSTANDARD)

-

-

-#---------------- Assembler Options ----------------

-#  -Wa,...:   tell GCC to pass this to the assembler.

-#  -ahlms:    create listing

-#  -gstabs:   have the assembler create line number information; note that

-#             for use in COFF files, additional information about filenames

-#             and function names needs to be present in the assembler source

-#             files -- see avr-libc docs [FIXME: not yet described there]

-ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs 

-

-

-#---------------- Library Options ----------------

-# Minimalistic printf version

-PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min

-

-# Floating point printf version (requires MATH_LIB = -lm below)

-PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt

-

-# If this is left blank, then it will use the Standard printf version.

-PRINTF_LIB = 

-#PRINTF_LIB = $(PRINTF_LIB_MIN)

-#PRINTF_LIB = $(PRINTF_LIB_FLOAT)

-

-

-# Minimalistic scanf version

-SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min

-

-# Floating point + %[ scanf version (requires MATH_LIB = -lm below)

-SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt

-

-# If this is left blank, then it will use the Standard scanf version.

-SCANF_LIB = 

-#SCANF_LIB = $(SCANF_LIB_MIN)

-#SCANF_LIB = $(SCANF_LIB_FLOAT)

-

-

-MATH_LIB = -lm

-

-

-

-#---------------- External Memory Options ----------------

-

-# 64 KB of external RAM, starting after internal RAM (ATmega128!),

-# used for variables (.data/.bss) and heap (malloc()).

-#EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff

-

-# 64 KB of external RAM, starting after internal RAM (ATmega128!),

-# only used for heap (malloc()).

-#EXTMEMOPTS = -Wl,--defsym=__heap_start=0x801100,--defsym=__heap_end=0x80ffff

-

-EXTMEMOPTS =

-

-

-

-

-#---------------- Linker Options ----------------

-#  -Wl,...:     tell GCC to pass this to linker.

-#    -Map:      create map file

-#    --cref:    add cross reference to  map file

-LDFLAGS = -Wl,-Map=$(TARGET).map,--cref

-LDFLAGS += $(EXTMEMOPTS)

-LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB)

-

-

-#--------------- bootloader linker Options -------

-# BOOTLOADER_ADDRESS (=Start of Boot Loader section

-# in bytes - not words) is defined above.

-#LDFLAGS += -Wl,--section-start=.text=$(BOOTLOADER_ADDRESS) -nostartfiles -nodefaultlibs

-#LDFLAGS += -Wl,--section-start=.text=$(BOOTLOADER_ADDRESS) -nostartfiles

-LDFLAGS += -Wl,--section-start=.text=$(BOOTLOADER_ADDRESS)

-

-#---------------- Programming Options (avrdude) ----------------

-

-# Programming hardware: alf avr910 avrisp bascom bsd 

-# dt006 pavr picoweb pony-stk200 sp12 stk200 stk500

-#

-# Type: avrdude -c ?

-# to get a full listing.

-#

-AVRDUDE_PROGRAMMER = stk500v2

-

-# com1 = serial port. Use lpt1 to connect to parallel port.

-AVRDUDE_PORT = com1    # programmer connected to serial device

-

-AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex

-#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep

-

-

-# Uncomment the following if you want avrdude's erase cycle counter.

-# Note that this counter needs to be initialized first using -Yn,

-# see avrdude manual.

-#AVRDUDE_ERASE_COUNTER = -y

-

-# Uncomment the following if you do /not/ wish a verification to be

-# performed after programming the device.

-#AVRDUDE_NO_VERIFY = -V

-

-# Increase verbosity level.  Please use this when submitting bug

-# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> 

-# to submit bug reports.

-#AVRDUDE_VERBOSE = -v -v

-

-AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)

-AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)

-AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)

-AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)

-

-

-

-#---------------- Debugging Options ----------------

-

-# For simulavr only - target MCU frequency.

-DEBUG_MFREQ = $(F_CPU)

-

-# Set the DEBUG_UI to either gdb or insight.

-# DEBUG_UI = gdb

-DEBUG_UI = insight

-

-# Set the debugging back-end to either avarice, simulavr.

-DEBUG_BACKEND = avarice

-#DEBUG_BACKEND = simulavr

-

-# GDB Init Filename.

-GDBINIT_FILE = __avr_gdbinit

-

-# When using avarice settings for the JTAG

-JTAG_DEV = /dev/com1

-

-# Debugging port used to communicate between GDB / avarice / simulavr.

-DEBUG_PORT = 4242

-

-# Debugging host used to communicate between GDB / avarice / simulavr, normally

-#     just set to localhost unless doing some sort of crazy debugging when 

-#     avarice is running on a different computer.

-DEBUG_HOST = localhost

-

-

-

-#============================================================================

-

-

-# Define programs and commands.

-SHELL = sh

-CC = avr-gcc

-OBJCOPY = avr-objcopy

-OBJDUMP = avr-objdump

-SIZE = avr-size

-NM = avr-nm

-AVRDUDE = avrdude

-REMOVE = rm -f

-COPY = cp

-WINSHELL = cmd

-

-

-# Define Messages

-# English

-MSG_ERRORS_NONE = Errors: none

-MSG_BEGIN = -------- begin --------

-MSG_END = --------  end  --------

-MSG_SIZE_BEFORE = Size before: 

-MSG_SIZE_AFTER = Size after:

-MSG_COFF = Converting to AVR COFF:

-MSG_EXTENDED_COFF = Converting to AVR Extended COFF:

-MSG_FLASH = Creating load file for Flash:

-MSG_EEPROM = Creating load file for EEPROM:

-MSG_EXTENDED_LISTING = Creating Extended Listing:

-MSG_SYMBOL_TABLE = Creating Symbol Table:

-MSG_LINKING = Linking:

-MSG_COMPILING = Compiling:

-MSG_ASSEMBLING = Assembling:

-MSG_CLEANING = Cleaning project:

-

-

-

-

-# Define all object files.

-OBJ = $(SRC:.c=.o) $(ASRC:.S=.o) 

-

-# Define all listing files.

-LST = $(SRC:.c=.lst) $(ASRC:.S=.lst) 

-

-

-# Compiler flags to generate dependency files.

-GENDEPFLAGS = -MD -MP -MF .dep/$(@F).d

-

-

-# Combine all necessary flags and optional flags.

-# Add target processor to flags.

-ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS)

-ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)

-

-

-

-############################################################

-#	May 25,	2010	<MLS> Adding 1280 support

-mega1280: MCU = atmega1280

-mega1280: F_CPU = 16000000

-mega1280: BOOTLOADER_ADDRESS = 1E000

-mega1280: CFLAGS += -D_MEGA_BOARD_

-mega1280: begin gccversion sizebefore build sizeafter end 

-			mv $(TARGET).hex stk500boot_v2_mega1280.hex

-

-

-############################################################

-#	Jul 6,	2010	<MLS> Adding 2560 support

-mega2560:	MCU = atmega2560

-mega2560:	F_CPU = 16000000

-mega2560:	BOOTLOADER_ADDRESS = 3E000

-mega2560:	CFLAGS += -D_MEGA_BOARD_

-mega2560:	begin gccversion sizebefore build sizeafter end 

-			mv $(TARGET).hex stk500boot_v2_mega2560.hex

-

-

-############################################################

-#Initial config on Amber128 board

-#	avrdude: Device signature = 0x1e9702

-#	avrdude: safemode: lfuse reads as 8F

-#	avrdude: safemode: hfuse reads as CB

-#	avrdude: safemode: efuse reads as FF

-#	Jul 17,	2010	<MLS> Adding 128 support

-############################################################

-amber128: MCU = atmega128

-#amber128: F_CPU = 16000000

-amber128: F_CPU = 14745600

-amber128: BOOTLOADER_ADDRESS = 1E000

-amber128: CFLAGS += -D_BOARD_AMBER128_

-amber128: begin gccversion sizebefore build sizeafter end 

-			mv $(TARGET).hex stk500boot_v2_amber128.hex

-

-############################################################

-#	Aug 23, 2010 	<MLS> Adding atmega2561 support

-m2561: MCU = atmega2561

-m2561: F_CPU = 8000000

-m2561: BOOTLOADER_ADDRESS = 3E000

-m2561: CFLAGS += -D_ANDROID_2561_ -DBAUDRATE=57600

-m2561: begin gccversion sizebefore build sizeafter end 

-			mv $(TARGET).hex stk500boot_v2_android2561.hex

-

-

-############################################################

-#	avrdude: Device signature = 0x1e9801

-#	avrdude: safemode: lfuse reads as EC

-#	avrdude: safemode: hfuse reads as 18

-#	avrdude: safemode: efuse reads as FD

-#	Aug 23,	2010	<MLS> Adding cerebot 2560 @ 8mhz

-#avrdude -P usb -c usbtiny -p m2560 -v -U flash:w:/Arduino/WiringBootV2_upd1/stk500boot_v2_cerebotplus.hex 

-############################################################

-cerebot:	MCU = atmega2560

-cerebot:	F_CPU = 8000000

-cerebot:	BOOTLOADER_ADDRESS = 3E000

-cerebot:	CFLAGS += -D_CEREBOTPLUS_BOARD_ -DBAUDRATE=38400 -DUART_BAUDRATE_DOUBLE_SPEED=1

-cerebot:	begin gccversion sizebefore build sizeafter end 

-			mv $(TARGET).hex stk500boot_v2_cerebotplus.hex

-

-

-############################################################

-#	Aug 23, 2010 	<MLS> Adding atmega2561 support

-penguino: MCU = atmega32

-penguino: F_CPU = 16000000

-penguino: BOOTLOADER_ADDRESS = 7800

-penguino: CFLAGS += -D_PENGUINO_ -DBAUDRATE=57600

-penguino: begin gccversion sizebefore build sizeafter end 

-			mv $(TARGET).hex stk500boot_v2_penguino.hex

-

-

-# Default target.

-all: begin gccversion sizebefore build sizeafter end

-

-build: elf hex eep lss sym

-#build:  hex eep lss sym

-

-elf: $(TARGET).elf

-hex: $(TARGET).hex

-eep: $(TARGET).eep

-lss: $(TARGET).lss 

-sym: $(TARGET).sym

-

-

-

-# Eye candy.

-# AVR Studio 3.x does not check make's exit code but relies on

-# the following magic strings to be generated by the compile job.

-begin:

-	@echo

-	@echo $(MSG_BEGIN)

-

-end:

-	@echo $(MSG_END)

-	@echo

-

-

-# Display size of file.

-HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex

-ELFSIZE = $(SIZE) --format=avr --mcu=$(MCU) $(TARGET).elf

-

-sizebefore:

-	@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \

-	2>/dev/null; echo; fi

-

-sizeafter:

-	@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \

-	2>/dev/null; echo; fi

-

-

-

-# Display compiler version information.

-gccversion : 

-	@$(CC) --version

-

-

-

-# Program the device.  

-program: $(TARGET).hex $(TARGET).eep

-	$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)

-

-

-# Generate avr-gdb config/init file which does the following:

-#     define the reset signal, load the target file, connect to target, and set 

-#     a breakpoint at main().

-gdb-config: 

-	@$(REMOVE) $(GDBINIT_FILE)

-	@echo define reset >> $(GDBINIT_FILE)

-	@echo SIGNAL SIGHUP >> $(GDBINIT_FILE)

-	@echo end >> $(GDBINIT_FILE)

-	@echo file $(TARGET).elf >> $(GDBINIT_FILE)

-	@echo target remote $(DEBUG_HOST):$(DEBUG_PORT)  >> $(GDBINIT_FILE)

-ifeq ($(DEBUG_BACKEND),simulavr)

-	@echo load  >> $(GDBINIT_FILE)

-endif	

-	@echo break main >> $(GDBINIT_FILE)

-	

-debug: gdb-config $(TARGET).elf

-ifeq ($(DEBUG_BACKEND), avarice)

-	@echo Starting AVaRICE - Press enter when "waiting to connect" message displays.

-	@$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \

-	$(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT)

-	@$(WINSHELL) /c pause

-	

-else

-	@$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \

-	$(DEBUG_MFREQ) --port $(DEBUG_PORT)

-endif

-	@$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE)

-	

-

-

-

-# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.

-COFFCONVERT=$(OBJCOPY) --debugging \

---change-section-address .data-0x800000 \

---change-section-address .bss-0x800000 \

---change-section-address .noinit-0x800000 \

---change-section-address .eeprom-0x810000 

-

-

-

-coff: $(TARGET).elf

-	@echo

-	@echo $(MSG_COFF) $(TARGET).cof

-	$(COFFCONVERT) -O coff-avr $< $(TARGET).cof

-

-

-extcoff: $(TARGET).elf

-	@echo

-	@echo $(MSG_EXTENDED_COFF) $(TARGET).cof

-	$(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof

-

-

-# Create final output files (.hex, .eep) from ELF output file.

-%.hex: %.elf

-	@echo

-	@echo $(MSG_FLASH) $@

-	$(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@

-

-%.eep: %.elf

-	@echo

-	@echo $(MSG_EEPROM) $@

-	-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \

-	--change-section-lma .eeprom=0 -O $(FORMAT) $< $@

-

-# Create extended listing file from ELF output file.

-%.lss: %.elf

-	@echo

-	@echo $(MSG_EXTENDED_LISTING) $@

-	$(OBJDUMP) -h -S $< > $@

-

-# Create a symbol table from ELF output file.

-%.sym: %.elf

-	@echo

-	@echo $(MSG_SYMBOL_TABLE) $@

-	$(NM) -n $< > $@

-

-

-

-# Link: create ELF output file from object files.

-.SECONDARY : $(TARGET).elf

-.PRECIOUS : $(OBJ)

-%.elf: $(OBJ)

-	@echo

-	@echo $(MSG_LINKING) $@

-	$(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS)

-

-

-# Compile: create object files from C source files.

-%.o : %.c

-	@echo

-	@echo $(MSG_COMPILING) $<

-	$(CC) -c $(ALL_CFLAGS) $< -o $@ 

-

-

-# Compile: create assembler files from C source files.

-%.s : %.c

-	$(CC) -S $(ALL_CFLAGS) $< -o $@

-

-

-# Assemble: create object files from assembler source files.

-%.o : %.S

-	@echo

-	@echo $(MSG_ASSEMBLING) $<

-	$(CC) -c $(ALL_ASFLAGS) $< -o $@

-

-# Create preprocessed source for use in sending a bug report.

-%.i : %.c

-	$(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@ 

-

-

-# Target: clean project.

-clean: begin clean_list end

-

-clean_list :

-	@echo

-	@echo $(MSG_CLEANING)

-	$(REMOVE) *.hex

-	$(REMOVE) *.eep

-	$(REMOVE) *.cof

-	$(REMOVE) *.elf

-	$(REMOVE) *.map

-	$(REMOVE) *.sym

-	$(REMOVE) *.lss

-	$(REMOVE) $(OBJ)

-	$(REMOVE) $(LST)

-	$(REMOVE) $(SRC:.c=.s)

-	$(REMOVE) $(SRC:.c=.d)

-	$(REMOVE) .dep/*

-

-

-

-# Include the dependency files.

--include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*)

-

-

-# Listing of phony targets.

-.PHONY : all begin finish end sizebefore sizeafter gccversion \

-build elf hex eep lss sym coff extcoff \

-clean clean_list program debug gdb-config

-