| Age | Commit message (Collapse) | Author |
|---|
|
|
|
See:
https://github.com/arduino/Arduino/commit/9ac7e30252fce5b9dafde3288519b020b73c37bd#commitcomment-6718676
|
|
|
|
See #1953
|
|
|
|
Read CDC data from USB FIFO on demand instead of in ISR.
Remove superfluous ring buffer.
Signed-off-by: Paul Brook <paul@nowt.org>
|
|
|
|
See #1877
|
|
|
|
Add two argument form of Serial_::begin
Signed-off-by: Paul Brook <paul@nowt.org>
|
|
Make USB Serial_::begin() function take an unsigned long argument for
consistency with HardwareSerial.
Signed-off-by: Paul Brook <paul@nowt.org>
|
|
|
|
|
|
|
|
self-programming mode
|
|
This reverts commit 200eefb4e2ac7796c5c901e8fd9369c85ec544c5.
|
|
This reverts commit ade4893f585e3e94fa6cf683620e1d12afc88ecd.
|
|
Delay fixes problem where the port has been configured but not quite opened. Federico found that 10 ms was the minimum time needed to avoid problems.
|
|
is ready to send data.
Mostly useful for Leonardo - simple way to test whether the port is actually opened by an application and ready to receive data. For Serial objects attached to real UARTs always returns true.
|
|
Since we use a magic RAM flag to signal to the bootloader there's a risk of the sketch overwriting the magic RAM location before the bootloader starts. By reducing the watchdog timeout we reduce the chance of this happening.
|
|
is opened at 1200 bps. (Dave Mellis)
|
|
|
|
Reset into bootloader is much snappier.
|
|
Before the sketch initiates an auto-reset for upload it pokes a magic word into a specific RAM address. On starting the bootloader checks this address. If it finds the magic word it knows the bootloader code should run. If not it jumps straight back to sketch.
Test in a sketch by adding to setup():
wdt_enable(WDTO_2S);
Sketch should upload, start, run for two seconds, WDT, and sketch should restart (not bootloader).
Had to cut out unused descriptor code to make the bootloader still fit in 4k.
|
|
On Windows COM port changes when board switched between bootloader and sketch. No way to prevent this so now Windows users have to select the upload port separate from the comm port. Also, handling of reset into bootloader was broken on Windows. Would occasionally leave the original COM port completely unusable. Changed the way this reset is initiated.
Finally, had to add upload.disable.flushing=true flag to boards.txt so IDE wouldn't try to flush the original COM port after it disappeared.
|
|
AvrdudeUploader class opens and closes Leonardo port at the magic baudrate before starting avrdude; reduced reset timeout from 250 ms to 15 ms
|
|
had to remove TIMER1 operation from bootloader - was interfering with normal sketch operation
|
|
This fixes the issue Federico reported where bytes written by host but not read by sketch would cause serial connection to lock up. Ring buffer implementation is based on HardwareSerial.cpp.
Adds public accept() method to CDC.
|
|
Interrupt-driven version was a dead-end - too many bugs with that approach.
|
|
old bootloader could fit in only 2 kB of flash. new version has to have a 4 kB block - jump-to address and boards.txt must reflect this.
|
|
attempts to fail. fixed bug in reboot routine, changed fuses to select 1024-word bootloader size, disabled hardware boot enable.
|
|
Windows. now reboots when a port, opened at 1200 bps, is closed.
|
|
arduino protocol for Leonardo avrdude upload.
|
|
USB_Send errors in CDC.
|
|
|
|
write behavior
|
|
support 300 bps connection, changed core and boards.txt to match
|
|
|
|
|
|
asserted, no matter what CDC baud rate is selected.
|
|
Integrated rest of Peter's USB implementation
|
