arduino-avr-xinput - A fork of Dmadison's Xinput Arduino avr core with a package.json

Age	Commit message (Collapse)	Author
2012-12-10	Merged 1.0.3	Cristian Maglie

2012-12-10	fixed permissions on a lot of text files. see #1116	Federico Fissore

2012-12-10	Fixed some firmware filenames	Cristian Maglie

2012-12-07	Added Esplora precompiled firmware	Cristian Maglie

2012-12-07	Added support for Arduino Esplora	Cristian Maglie

2012-11-30	Updated firmware for atmega8 for new avr-gcc versions.	Cristian Maglie
	fixes #153 fixes #1122
2012-11-30	Saved old Leonardo and Micro production firmware.	Cristian Maglie
	Rebuilt firmware for Micro. Added pre-loaded Blink to new firmwares.
2012-11-30	Improved Leonardo bootloader	Kristian Lauszus
	The power-on reset detection didn't work properly, but has now been fixed
2012-11-23	Caterina changes to support Micro. includes newly rebuilt version of the ↵	Zachary Eveland
	bootloader merged with Blink produced using 1.0.2
2012-11-02	Updating Micro bootloader firmware.	David A. Mellis

2012-11-01	Adding LilyPad Arduino USB.	David A. Mellis

2012-10-27	Adding Micro.	David A. Mellis

2012-04-25	changed PID values for Leonardo bootloader and sketch	Zach Eveland
	done to avoid driver problems for users who installed the pre-release bootloader and driver
2012-04-11	merged Caterina with Blink	Zach Eveland

2012-04-11	fixed logic bug in Caterina that could stop the bootloader from entering ↵	Zach Eveland
	self-programming mode
2012-04-09	Micro I hardly knew ye	Zach Eveland

2012-04-09	Micro and Leonardo bootloaders for distribution are now merged with Blink sketch	Zach Eveland

2012-04-09	PID and VID are no longer hard-coded in bootloader. instead they are passed ↵	Zach Eveland
	in at compile-time from makefile. also added and renamed built bootloader images for Micro and Leonardo
2012-03-14	bugfix for Caterina not starting sketch if "verify upload" turned off in IDE.	Zach Eveland
	Previously, if avrdude skipped the upload step the read while write memory might never be reenabled. This would prevent the bootloader from ending and the sketch from starting - the bootloader just continued to run even after a successful upload. Now enable RWW when we receive the AVR109 "Exit bootloader" 'E' command. Had to disable lock bit changing support in the bootloader to free up flash for the change - will anyone miss it?
2012-03-14	changed Caterina timeout after self-programming to 500 ms (from 250 ms)	Zach Eveland
	attempt to fix bug reported by Dave Mellis: "avrdude: ser_close(): can’t reset attributes for device: Invalid argument" is thrown after attempting an upload in the IDE (though the upload seems to be successful)
2012-03-08	give Leonardo bootloader 250 ms to finish housekeeping before leaving ↵	Zach Eveland
	self-programming mode Earlier approach had bootloader end as soon as it was told to. On Linux this caused problems with avrdude because the microcontroller never had a chance to send an acknowledgement.
2012-03-08	removed old version of Leonardo's caterina bootloader, replaced with ↵	Zach Eveland
	LUFA-based caterina
2012-03-01	reduced Caterina timeout to 8 seconds from 16	Zach Eveland

2012-02-14	Leonardo now checks whether bootloader should be run after a WDT event.	Zach Eveland
	Before the sketch initiates an auto-reset for upload it pokes a magic word into a specific RAM address. On starting the bootloader checks this address. If it finds the magic word it knows the bootloader code should run. If not it jumps straight back to sketch. Test in a sketch by adding to setup(): wdt_enable(WDTO_2S); Sketch should upload, start, run for two seconds, WDT, and sketch should restart (not bootloader). Had to cut out unused descriptor code to make the bootloader still fit in 4k.
2012-02-14	Leonardo bootloader jumps straight to sketch for a power-on reset.	Zach Eveland
	Disconnect programmer after burning bootloader to get the full effect. ICSP and JTAG programmers do a hardware reset after any reset condition, confusing the firmware a little.
2012-02-13	changed Leonardo bootloader and sketch PID values again (now 0x0701 for ↵	Zach Eveland
	bootloader, 0x0801 for sketch)
2012-02-08	adjusting descriptors - trying to prevent sketch and bootloader from ↵	Zach Eveland
	grabbing different COM numbers on Windows
2012-02-07	changed Caterina descriptors - Arduino LLC VID, new PID, manufacturer ↵	Zach Eveland
	string, and serial number
2012-02-07	fixed bug in Caterina which caused some programming instructions to fail	Zach Eveland
	Timer 1 interrupts were trashing self-programming timing. Now disable Timer 1 compare match before doing Flash tasks and reenable afterward.
2012-02-06	increased Leonardo bootloader timeout to 16 seconds	Zach Eveland

2012-02-03	proper bootloader timeout and LED control in Leonardo bootloader	Zach Eveland

2012-01-24	Caterina now cleanly hands off operation to the sketch	Zach Eveland
	had to remove TIMER1 operation from bootloader - was interfering with normal sketch operation
2012-01-21	move interrupt vector table to application section before jumping to it ↵	Zach Eveland
	after upload finished.
2012-01-21	Leonardo bootloader checks reason for reset and jumps immediately to sketch ↵	Zach Eveland
	if reset was caused by WDT
2012-01-19	stripped all LUFA LED control. from LUFA-based Caterina	Zach Eveland

2012-01-19	changed fuses to select 4k bootloader for LUFA-based Caterina	Zach Eveland

2012-01-19	added Board/LEDs.h to LUFA-based Caterina	Zach Eveland

2012-01-19	superficial changes to stock LUFA CDC bootloader - renamed project, removed ↵	Zach Eveland
	unnecessary files
2012-01-19	initial checkin of LUFA 111009 CDC bootloader	Zach Eveland

2012-01-10	made Leonardo and Micro bootloader PIDs same as sketch PIDs	Zach Eveland

2012-01-10	restored composite and non-composite device descriptors (removed in ↵	Zach Eveland
	4b05c3fc7529477fb7031d42103c15b50a6b58be) Windows wants to see both types of device descriptors.
2012-01-10	reenabled HID to force Leonardo bootloader to enumerate as a composite device	Zach Eveland

2012-01-10	renamed DiskLoader to Caterina (after Leonardo's mom)	Zach Eveland

2012-01-10	changed USB PID for Leonardo and Micro bootloaders	Zach Eveland
	sketch and bootloader will use different PIDs to distinguish one from the other.
2012-01-10	fixed warning when comparing pgm_read_word(0) to -1 (thanks, Limor Fried and ↵	Zach Eveland
	Phillip Torrone)
2012-01-10	got rid of u8, u16, u32 typedefs in Diskloader	Zach Eveland
	done to bring types in line with others in Arduino core
2012-01-10	made the bootloader's LED control macro names less offensive	Zach Eveland
	TX_LED_OFF() instead of TXLED0, etc.
2012-01-10	added conditional compilation for HID, removed conditional compilation for ↵	Zach Eveland
	CDC (is always used). disabled HID by default. also always enumerates as composite now. the bootloader must always have a CDC interface. HID is optional and not even complete to reduce size.
2012-01-10	fix bug in handling of long descriptors for bootloader USB (thank you, Todd ↵	Zach Eveland
	Krein, Limor Fried, and Phillip Torrone) descriptors longer than 255 bytes were being shortened, causing problems with enumeration under Windows
2011-12-31	reset the Leonardo board when leaving the bootloader, before starting the sketch	Zach Eveland
	Done so all IO and other registers are properly reinitialized when a new sketch is uploaded or when an existing sketch is started. Uses a watchdog timeout with a 15 ms period to accomplish the reset. Bootloader checks the reason for reset and only enumerates as bootloader and enters the programming loop if reset was NOT caused by WDT.