aboutsummaryrefslogtreecommitdiff
path: root/bootloaders
AgeCommit message (Collapse)Author
2012-03-01reduced Caterina timeout to 8 seconds from 16Zach Eveland
2012-02-14Leonardo now checks whether bootloader should be run after a WDT event.Zach Eveland
Before the sketch initiates an auto-reset for upload it pokes a magic word into a specific RAM address. On starting the bootloader checks this address. If it finds the magic word it knows the bootloader code should run. If not it jumps straight back to sketch. Test in a sketch by adding to setup(): wdt_enable(WDTO_2S); Sketch should upload, start, run for two seconds, WDT, and sketch should restart (not bootloader). Had to cut out unused descriptor code to make the bootloader still fit in 4k.
2012-02-14Leonardo bootloader jumps straight to sketch for a power-on reset.Zach Eveland
Disconnect programmer after burning bootloader to get the full effect. ICSP and JTAG programmers do a hardware reset after any reset condition, confusing the firmware a little.
2012-02-13changed Leonardo bootloader and sketch PID values again (now 0x0701 for ↵Zach Eveland
bootloader, 0x0801 for sketch)
2012-02-08adjusting descriptors - trying to prevent sketch and bootloader from ↵Zach Eveland
grabbing different COM numbers on Windows
2012-02-07changed Caterina descriptors - Arduino LLC VID, new PID, manufacturer ↵Zach Eveland
string, and serial number
2012-02-07fixed bug in Caterina which caused some programming instructions to failZach Eveland
Timer 1 interrupts were trashing self-programming timing. Now disable Timer 1 compare match before doing Flash tasks and reenable afterward.
2012-02-06increased Leonardo bootloader timeout to 16 secondsZach Eveland
2012-02-03proper bootloader timeout and LED control in Leonardo bootloaderZach Eveland
2012-01-24Caterina now cleanly hands off operation to the sketchZach Eveland
had to remove TIMER1 operation from bootloader - was interfering with normal sketch operation
2012-01-21move interrupt vector table to application section before jumping to it ↵Zach Eveland
after upload finished.
2012-01-21Leonardo bootloader checks reason for reset and jumps immediately to sketch ↵Zach Eveland
if reset was caused by WDT
2012-01-19stripped all LUFA LED control. from LUFA-based CaterinaZach Eveland
2012-01-19changed fuses to select 4k bootloader for LUFA-based CaterinaZach Eveland
2012-01-19added Board/LEDs.h to LUFA-based CaterinaZach Eveland
2012-01-19superficial changes to stock LUFA CDC bootloader - renamed project, removed ↵Zach Eveland
unnecessary files
2012-01-19initial checkin of LUFA 111009 CDC bootloaderZach Eveland
2012-01-10made Leonardo and Micro bootloader PIDs same as sketch PIDsZach Eveland
2012-01-10restored composite and non-composite device descriptors (removed in ↵Zach Eveland
4b05c3fc7529477fb7031d42103c15b50a6b58be) Windows wants to see both types of device descriptors.
2012-01-10reenabled HID to force Leonardo bootloader to enumerate as a composite deviceZach Eveland
2012-01-10renamed DiskLoader to Caterina (after Leonardo's mom)Zach Eveland
2012-01-10changed USB PID for Leonardo and Micro bootloadersZach Eveland
sketch and bootloader will use different PIDs to distinguish one from the other.
2012-01-10fixed warning when comparing pgm_read_word(0) to -1 (thanks, Limor Fried and ↵Zach Eveland
Phillip Torrone)
2012-01-10got rid of u8, u16, u32 typedefs in DiskloaderZach Eveland
done to bring types in line with others in Arduino core
2012-01-10made the bootloader's LED control macro names less offensiveZach Eveland
TX_LED_OFF() instead of TXLED0, etc.
2012-01-10added conditional compilation for HID, removed conditional compilation for ↵Zach Eveland
CDC (is always used). disabled HID by default. also always enumerates as composite now. the bootloader must always have a CDC interface. HID is optional and not even complete to reduce size.
2012-01-10fix bug in handling of long descriptors for bootloader USB (thank you, Todd ↵Zach Eveland
Krein, Limor Fried, and Phillip Torrone) descriptors longer than 255 bytes were being shortened, causing problems with enumeration under Windows
2011-12-31reset the Leonardo board when leaving the bootloader, before starting the sketchZach Eveland
Done so all IO and other registers are properly reinitialized when a new sketch is uploaded or when an existing sketch is started. Uses a watchdog timeout with a 15 ms period to accomplish the reset. Bootloader checks the reason for reset and only enumerates as bootloader and enters the programming loop if reset was NOT caused by WDT.
2011-12-26bootloader merged with blink sketchZach Eveland
full set of descriptors in sketch fixes driver installation issue on Win7.
2011-11-25Correcting Arduino Mini w/ ATmega328 bootloader file and fuses (untested).David A. Mellis
2011-11-16Leonardo bootloader now sends iSerial string during enumeration. Seems to ↵Zach Eveland
satisfy Windows' composite device requirements.
2011-11-09restored original non-interrupt-driven DiskLoaderZach Eveland
Interrupt-driven version was a dead-end - too many bugs with that approach.
2011-10-31changed Leonardo PID to 0x0032 for Diskloader testing. updated .inf to match.Zach Eveland
2011-10-31check to see if a sketch has been loaded before jumping out of bootloaderZach Eveland
2011-10-27Revert "Merge branch 'master' of github.com:arduino/Arduino into ↵Zach Eveland
diskloader_reboot" This reverts commit df9835efafd13685251749bc210c0b96a18a96a5, reversing changes made to ec45af8bfa9222a807c075dd1db4b5aa798bba03. Conflicts: hardware/arduino/variants/mega/pins_arduino.h libraries/Ethernet/examples/PachubeClientString/PachubeClientString.ino
2011-10-27bootloader runs sketch after timeout, added bootloader LED breathingZach Eveland
2011-10-27cosmetic changes - remove old comments, unused codeZach Eveland
2011-10-27removed conditional compilation checks for CDC_ENABLEDZach Eveland
bootloader must always have CDC enabled
2011-10-27removed old comments and unused USB core codeZach Eveland
2011-10-27brought nuevo_diskloader changes over to diskloaderZach Eveland
Moved nuevo_diskloader files into diskloader directory. Changed back to real PID for Leonardo
2011-10-27Merge branch 'master' of github.com:arduino/Arduino into diskloader_rebootZach Eveland
Conflicts: app/src/processing/app/Editor.java app/src/processing/app/Sketch.java build/shared/examples/4.Communication/SerialCallResponse/SerialCallResponse.pde build/shared/lib/theme/theme.txt hardware/arduino/cores/arduino/HardwareSerial.h hardware/arduino/cores/arduino/Print.cpp hardware/arduino/cores/arduino/WString.h hardware/arduino/variants/mega/pins_arduino.h libraries/Ethernet/examples/PachubeClient/PachubeClient.ino libraries/Ethernet/examples/PachubeClientString/PachubeClientString.ino libraries/Firmata/examples/EchoString/EchoString.ino libraries/SD/File.cpp libraries/SoftwareSerial/SoftwareSerial.cpp libraries/SoftwareSerial/SoftwareSerial.h libraries/SoftwareSerial/examples/SoftwareSerialExample/SoftwareSerialExample.ino libraries/SoftwareSerial/keywords.txt
2011-10-26working bootloader. had to move interrupts back to application section. ↵Zach Eveland
NOTE: need to have sketch CDC jump to appropriate place for bootloader - 4k from end instead of 2k
2011-10-26working (?!?!?!) bootloader. doesn't yet restart chip after upload completes.Zach Eveland
2011-10-26uploading now completes using RC2 on Win7Zach Eveland
2011-10-25closer still - now up to 4680Zach Eveland
2011-10-25progress on bootloader bug - have implemented blocking USB_Recv. avrdude ↵Zach Eveland
makes it to flash programming address 0400 or so before hanging
2011-10-24fixed logic bug in waiting for synch. stripped out all Serial stuffZach Eveland
2011-10-24removed old commentsZach Eveland
2011-10-23bootloader responds properly now. nearly there - still have an issue with ↵Zach Eveland
it falling out of sync after completing most operations
2011-10-21more attempts to get parameter sending to workZach Eveland
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-11-22 22:25:49 +0000