2 files changed, 0 insertions, 165 deletions
diff --git a/libraries/Bridge/examples/OLDWiFiCheck/OLDWiFiCheck.ino b/libraries/Bridge/examples/OLDWiFiCheck/OLDWiFiCheck.ino
deleted file mode 100644
index 1cb9f03..0000000
--- a/libraries/Bridge/examples/OLDWiFiCheck/OLDWiFiCheck.ino
+++ /dev/null
@@ -1,53 +0,0 @@
-/*
-  Arduino Yun Wireless Config Check
- 
- Checks the wireless state of Arduino Yun by calling
- the linux command iwconfig.
- 
- Upload this to an Arduino Yun via serial (not WiFi) 
- then open the serial monitor to see the status of
- your Yun's WiFi connection. If it's connected to 
- a wireless network, the ESSID (name) of that network
- and the signal strength will appear.
- 
- The circuit:
- * Arduino Yun
- 
- created 22 May 2013
- by Tom Igoe
- 
- This example code is in the public domain.
- */
-
-#include <Process.h>
-
-void setup() {
-  Serial.begin(9600);  // initialize serial communication
-  while(!Serial);      // do nothing until the serial monitor is opened
- 
-  pinMode(13,OUTPUT);  
-  digitalWrite(13, LOW);  
-  Bridge.begin();      // make contact with the linux processor
-  digitalWrite(13, HIGH); 
-
-  delay(2000);         // wait 2 seconds
-
-  Process wifiCheck;    // initialize a new process
-
-
-  wifiCheck.begin("iwconfig");        // command you want to run
-  wifiCheck.addParameter("wlan0");    // parameter of the command
-  wifiCheck.run();                    // run the command
-
-  // while there's any characters coming back from the 
-  // process, print them to the serial monitor:
-  while (wifiCheck.available() > 0) {
-    char thisChar = wifiCheck.read();
-    Serial.print(thisChar);
-  }
-}
-
-void loop() {
-  // nothing to do here.
-}
-
diff --git a/libraries/Bridge/examples/OLDWifiSignalStrengthIndicator/OLDWifiSignalStrengthIndicator.ino b/libraries/Bridge/examples/OLDWifiSignalStrengthIndicator/OLDWifiSignalStrengthIndicator.ino
deleted file mode 100644
index e0b2d1f..0000000
--- a/libraries/Bridge/examples/OLDWifiSignalStrengthIndicator/OLDWifiSignalStrengthIndicator.ino
+++ /dev/null
@@ -1,112 +0,0 @@
-/*
- Wifi Signal Strength Indicator
- 
- This example demonstrates the use of the bridge and process libraries 
- to communicate between the Arduino side and the linux side of the Arduino Yun. 
- 
- The Linux script returns the strength of the wifi signal.
- 
- The Arduino sketch uses LEDs to indicate whether the current value of 
- the signal strength is above, below, or the same as the last value 
- 
- The circuit: 
- * LEDs on pins 8, 9, and 10
- * Built-in LED on pin 13
- 
- The script:
- The following one line script must exist in the /root directory of the 
- linux file system, in a file named "wifiStrength.sh", and it must be executable:
- 
- tail -1 /proc/net/wireless | cut  -c22-23
- 
- created 06 June 2013
- by Michael Shiloh
- modified 08 June 2013
- by Tom Igoe
- 
- This example code is in the public domain
- 
- */
-
-
-#include <Process.h>
-
-// global variable to store the last value of the signal strength
-int lastValue;
-
-void setup() {
-  // set up LED pins as outputs:
-  pinMode(8, OUTPUT);
-  pinMode(9, OUTPUT);
-  pinMode(10, OUTPUT);
-  pinMode(13,OUTPUT);
-
-  // Indicate that you're ready by flashing pin 13 LED twice
-  for (int flash = 0; flash < 3; flash++) {
-    digitalWrite(13,HIGH);
-    delay(200);
-    digitalWrite(13,LOW);
-    delay(800);
-  }
-  // initialize Serial and Bridge:
-  Serial.begin(9600);
-  Bridge.begin();
-
-  // Indicate that setup is finished
-  digitalWrite(13,HIGH);
-}
-
-void loop() {
-  int value = 0;      // the signal strength as an integer
-  String result;      // the result of the process as a String
-  Process wifiCheck;  // the process itself
-
-
-  // Run the script on the linux side. Note that any word 
-  //or text separated by a tab or space is considered 
-  //an additional parameter:
-  wifiCheck.begin("ash");
-  wifiCheck.addParameter("/root/wifiStrength.sh");
-  wifiCheck.run();
-
-  // If the process has sent any characters:
-  while (wifiCheck.available()>0) {
-    result = wifiCheck.readString(); // read the result into a string
-    value = result.toInt();  // parse the string as an int
-  }
-
-  //  for debugging
-  Serial.print("previous strength:");  
-  Serial.print(lastValue);
-  Serial.print("\tcurrent strength:");  
-  Serial.println(value);
-
-  // indicate the relative string by lighting the appropriate LED
-  allOff();      // turn off all the LEDS
-
-  if (value > lastValue) {     // if the signal's getting stronger
-    digitalWrite(10, HIGH);
-  }
-  else if (value < lastValue){ // if the signal's getting weaker
-    digitalWrite(8, HIGH);
-  }
-  else {                       // if the signal's stayed steady
-    digitalWrite(9, HIGH);
-  }
-
-  lastValue = value; // record this value for next time
-  delay(10);      // small delay before next time through the loop
-}
-
-
-void allOff() {
-  digitalWrite(8, LOW);
-  digitalWrite(9, LOW);
-  digitalWrite(10, LOW); 
-}
-
-
-
-
-
-