2 files changed, 148 insertions, 0 deletions
diff --git a/libraries/SoftwareSerial/examples/SoftwareSerialExample/SoftwareSerialExample.ino b/libraries/SoftwareSerial/examples/SoftwareSerialExample/SoftwareSerialExample.ino
new file mode 100644
index 0000000..6101bb1
--- /dev/null
+++ b/libraries/SoftwareSerial/examples/SoftwareSerialExample/SoftwareSerialExample.ino
@@ -0,0 +1,55 @@
+/*
+  Software serial multple serial test
+ 
+ Receives from the hardware serial, sends to software serial.
+ Receives from software serial, sends to hardware serial.
+ 
+ The circuit: 
+ * RX is digital pin 10 (connect to TX of other device)
+ * TX is digital pin 11 (connect to RX of other device)
+ 
+ Note:
+ Not all pins on the Mega and Mega 2560 support change interrupts, 
+ so only the following can be used for RX: 
+ 10, 11, 12, 13, 50, 51, 52, 53, 62, 63, 64, 65, 66, 67, 68, 69
+ 
+ Not all pins on the Leonardo support change interrupts, 
+ so only the following can be used for RX: 
+ 8, 9, 10, 11, 14 (MISO), 15 (SCK), 16 (MOSI).
+ 
+ created back in the mists of time
+ modified 25 May 2012
+ by Tom Igoe
+ based on Mikal Hart's example
+ 
+ This example code is in the public domain.
+ 
+ */
+#include <SoftwareSerial.h>
+
+SoftwareSerial mySerial(10, 11); // RX, TX
+
+void setup()  
+{
+  // Open serial communications and wait for port to open:
+  Serial.begin(57600);
+  while (!Serial) {
+    ; // wait for serial port to connect. Needed for Leonardo only
+  }
+
+
+  Serial.println("Goodnight moon!");
+
+  // set the data rate for the SoftwareSerial port
+  mySerial.begin(4800);
+  mySerial.println("Hello, world?");
+}
+
+void loop() // run over and over
+{
+  if (mySerial.available())
+    Serial.write(mySerial.read());
+  if (Serial.available())
+    mySerial.write(Serial.read());
+}
+
diff --git a/libraries/SoftwareSerial/examples/TwoPortReceive/TwoPortReceive.ino b/libraries/SoftwareSerial/examples/TwoPortReceive/TwoPortReceive.ino
new file mode 100644
index 0000000..d607ee6
--- /dev/null
+++ b/libraries/SoftwareSerial/examples/TwoPortReceive/TwoPortReceive.ino
@@ -0,0 +1,93 @@
+/*
+  Software serial multple serial test
+ 
+ Receives from the two software serial ports, 
+ sends to the hardware serial port. 
+ 
+ In order to listen on a software port, you call port.listen(). 
+ When using two software serial ports, you have to switch ports
+ by listen()ing on each one in turn. Pick a logical time to switch
+ ports, like the end of an expected transmission, or when the 
+ buffer is empty. This example switches ports when there is nothing
+ more to read from a port
+ 
+ The circuit: 
+ Two devices which communicate serially are needed.
+ * First serial device's TX attached to digital pin 2, RX to pin 3
+ * Second serial device's TX attached to digital pin 4, RX to pin 5
+ 
+ Note:
+ Not all pins on the Mega and Mega 2560 support change interrupts, 
+ so only the following can be used for RX: 
+ 10, 11, 12, 13, 50, 51, 52, 53, 62, 63, 64, 65, 66, 67, 68, 69
+ 
+ Not all pins on the Leonardo support change interrupts, 
+ so only the following can be used for RX: 
+ 8, 9, 10, 11, 14 (MISO), 15 (SCK), 16 (MOSI).
+ 
+ created 18 Apr. 2011
+ modified 25 May 2012
+ by Tom Igoe
+ based on Mikal Hart's twoPortRXExample
+ 
+ This example code is in the public domain.
+ 
+ */
+
+#include <SoftwareSerial.h>
+// software serial #1: TX = digital pin 10, RX = digital pin 11
+SoftwareSerial portOne(10,11);
+
+// software serial #2: TX = digital pin 8, RX = digital pin 9
+// on the Mega, use other pins instead, since 8 and 9 don't work on the Mega
+SoftwareSerial portTwo(8,9);
+
+void setup()
+{
+ // Open serial communications and wait for port to open:
+  Serial.begin(9600);
+   while (!Serial) {
+    ; // wait for serial port to connect. Needed for Leonardo only
+  }
+
+
+  // Start each software serial port
+  portOne.begin(9600);
+  portTwo.begin(9600);
+}
+
+void loop()
+{
+  // By default, the last intialized port is listening.
+  // when you want to listen on a port, explicitly select it:
+  portOne.listen();
+  Serial.println("Data from port one:");
+  // while there is data coming in, read it
+  // and send to the hardware serial port:
+  while (portOne.available() > 0) {
+    char inByte = portOne.read();
+    Serial.write(inByte);
+  }
+
+  // blank line to separate data from the two ports:
+  Serial.println();
+
+  // Now listen on the second port
+  portTwo.listen();
+  // while there is data coming in, read it
+  // and send to the hardware serial port:
+  Serial.println("Data from port two:");
+  while (portTwo.available() > 0) {
+    char inByte = portTwo.read();
+    Serial.write(inByte);
+  }
+
+  // blank line to separate data from the two ports:
+  Serial.println();
+}
+
+
+
+
+
+