diff options
Diffstat (limited to 'libraries/SPI/examples')
3 files changed, 357 insertions, 0 deletions
diff --git a/libraries/SPI/examples/BarometricPressureSensor/BarometricPressureSensor.ino b/libraries/SPI/examples/BarometricPressureSensor/BarometricPressureSensor.ino new file mode 100644 index 0000000..9d77a42 --- /dev/null +++ b/libraries/SPI/examples/BarometricPressureSensor/BarometricPressureSensor.ino @@ -0,0 +1,143 @@ +/* + SCP1000 Barometric Pressure Sensor Display + + Shows the output of a Barometric Pressure Sensor on a + Uses the SPI library. For details on the sensor, see: + http://www.sparkfun.com/commerce/product_info.php?products_id=8161 + http://www.vti.fi/en/support/obsolete_products/pressure_sensors/ + + This sketch adapted from Nathan Seidle's SCP1000 example for PIC: + http://www.sparkfun.com/datasheets/Sensors/SCP1000-Testing.zip + + Circuit: + SCP1000 sensor attached to pins 6, 7, 10 - 13: + DRDY: pin 6 + CSB: pin 7 + MOSI: pin 11 + MISO: pin 12 + SCK: pin 13 + + created 31 July 2010 + modified 14 August 2010 + by Tom Igoe + */ + +// the sensor communicates using SPI, so include the library: +#include <SPI.h> + +//Sensor's memory register addresses: +const int PRESSURE = 0x1F; //3 most significant bits of pressure +const int PRESSURE_LSB = 0x20; //16 least significant bits of pressure +const int TEMPERATURE = 0x21; //16 bit temperature reading +const byte READ = 0b11111100; // SCP1000's read command +const byte WRITE = 0b00000010; // SCP1000's write command + +// pins used for the connection with the sensor +// the other you need are controlled by the SPI library): +const int dataReadyPin = 6; +const int chipSelectPin = 7; + +void setup() { + Serial.begin(9600); + + // start the SPI library: + SPI.begin(); + + // initalize the data ready and chip select pins: + pinMode(dataReadyPin, INPUT); + pinMode(chipSelectPin, OUTPUT); + + //Configure SCP1000 for low noise configuration: + writeRegister(0x02, 0x2D); + writeRegister(0x01, 0x03); + writeRegister(0x03, 0x02); + // give the sensor time to set up: + delay(100); +} + +void loop() { + //Select High Resolution Mode + writeRegister(0x03, 0x0A); + + // don't do anything until the data ready pin is high: + if (digitalRead(dataReadyPin) == HIGH) { + //Read the temperature data + int tempData = readRegister(0x21, 2); + + // convert the temperature to celsius and display it: + float realTemp = (float)tempData / 20.0; + Serial.print("Temp[C]="); + Serial.print(realTemp); + + + //Read the pressure data highest 3 bits: + byte pressure_data_high = readRegister(0x1F, 1); + pressure_data_high &= 0b00000111; //you only needs bits 2 to 0 + + //Read the pressure data lower 16 bits: + unsigned int pressure_data_low = readRegister(0x20, 2); + //combine the two parts into one 19-bit number: + long pressure = ((pressure_data_high << 16) | pressure_data_low)/4; + + // display the temperature: + Serial.println("\tPressure [Pa]=" + String(pressure)); + } +} + +//Read from or write to register from the SCP1000: +unsigned int readRegister(byte thisRegister, int bytesToRead ) { + byte inByte = 0; // incoming byte from the SPI + unsigned int result = 0; // result to return + Serial.print(thisRegister, BIN); + Serial.print("\t"); + // SCP1000 expects the register name in the upper 6 bits + // of the byte. So shift the bits left by two bits: + thisRegister = thisRegister << 2; + // now combine the address and the command into one byte + byte dataToSend = thisRegister & READ; + Serial.println(thisRegister, BIN); + // take the chip select low to select the device: + digitalWrite(chipSelectPin, LOW); + // send the device the register you want to read: + SPI.transfer(dataToSend); + // send a value of 0 to read the first byte returned: + result = SPI.transfer(0x00); + // decrement the number of bytes left to read: + bytesToRead--; + // if you still have another byte to read: + if (bytesToRead > 0) { + // shift the first byte left, then get the second byte: + result = result << 8; + inByte = SPI.transfer(0x00); + // combine the byte you just got with the previous one: + result = result | inByte; + // decrement the number of bytes left to read: + bytesToRead--; + } + // take the chip select high to de-select: + digitalWrite(chipSelectPin, HIGH); + // return the result: + return(result); +} + + +//Sends a write command to SCP1000 + +void writeRegister(byte thisRegister, byte thisValue) { + + // SCP1000 expects the register address in the upper 6 bits + // of the byte. So shift the bits left by two bits: + thisRegister = thisRegister << 2; + // now combine the register address and the command into one byte: + byte dataToSend = thisRegister | WRITE; + + // take the chip select low to select the device: + digitalWrite(chipSelectPin, LOW); + + SPI.transfer(dataToSend); //Send register location + SPI.transfer(thisValue); //Send value to record into register + + // take the chip select high to de-select: + digitalWrite(chipSelectPin, HIGH); +} + diff --git a/libraries/SPI/examples/BarometricPressureSensor/BarometricPressureSensor/BarometricPressureSensor.ino b/libraries/SPI/examples/BarometricPressureSensor/BarometricPressureSensor/BarometricPressureSensor.ino new file mode 100644 index 0000000..9c9c9b6 --- /dev/null +++ b/libraries/SPI/examples/BarometricPressureSensor/BarometricPressureSensor/BarometricPressureSensor.ino @@ -0,0 +1,143 @@ +/* + SCP1000 Barometric Pressure Sensor Display + + Shows the output of a Barometric Pressure Sensor on a + Uses the SPI library. For details on the sensor, see: + http://www.sparkfun.com/commerce/product_info.php?products_id=8161 + http://www.vti.fi/en/support/obsolete_products/pressure_sensors/ + + This sketch adapted from Nathan Seidle's SCP1000 example for PIC: + http://www.sparkfun.com/datasheets/Sensors/SCP1000-Testing.zip + + Circuit: + SCP1000 sensor attached to pins 6, 7, 10 - 13: + DRDY: pin 6 + CSB: pin 7 + MOSI: pin 11 + MISO: pin 12 + SCK: pin 13 + + created 31 July 2010 + modified 14 August 2010 + by Tom Igoe + */ + +// the sensor communicates using SPI, so include the library: +#include <SPI.h> + +//Sensor's memory register addresses: +const int PRESSURE = 0x1F; //3 most significant bits of pressure +const int PRESSURE_LSB = 0x20; //16 least significant bits of pressure +const int TEMPERATURE = 0x21; //16 bit temperature reading +cont byte READ = 0b00000000; // SCP1000's read command +const byte WRITE = 0b00000010; // SCP1000's write command +// pins used for the connection with the sensor +// the other you need are controlled by the SPI library): +const int dataReadyPin = 6; +const int chipSelectPin = 7; + +void setup() { + Serial.begin(9600); + + // start the SPI library: + SPI.begin(); + + // initalize the data ready and chip select pins: + pinMode(dataReadyPin, INPUT); + pinMode(chipSelectPin, OUTPUT); + + //Configure SCP1000 for low noise configuration: + writeRegister(0x02, 0x2D); + writeRegister(0x01, 0x03); + writeRegister(0x03, 0x02); + // give the sensor time to set up: + delay(100); +} + +void loop() { + //Select High Resolution Mode + writeRegister(0x03, 0x0A); + + // don't do anything until the data ready pin is high: + if (digitalRead(dataReadyPin) == HIGH) { + //Read the temperature data + int tempData = readRegister(0x21, 2); + + // convert the temperature to celsius and display it: + float realTemp = (float)tempData / 20.0; + Serial.print("Temp[C]="); + Serial.print(realTemp); + + + //Read the pressure data highest 3 bits: + byte pressure_data_high = readRegister(0x1F, 1); + pressure_data_high &= 0b00000111; //you only needs bits 2 to 0 + + //Read the pressure data lower 16 bits: + unsigned int pressure_data_low = readRegister(0x20, 2); + //combine the two parts into one 19-bit number: + long pressure = ((pressure_data_high << 16) | pressure_data_low)/4; + + // display the temperature: + Serial.println("\tPressure [Pa]=" + String(pressure)); + } +} + +//Read from or write to register from the SCP1000: +unsigned int readRegister(byte thisRegister, int bytesToRead ) { + byte inByte = 0; // incoming byte from the SPI + unsigned int result = 0; // result to return + + // SCP1000 expects the register name in the upper 6 bits + // of the byte. So shift the bits left by two bits: + thisRegister = thisRegister << 2; + // now combine the address and the command into one byte + dataToSend = thisRegister & READ; + + // take the chip select low to select the device: + digitalWrite(chipSelectPin, LOW); + // send the device the register you want to read: + SPI.transfer(dataToSend); + // send a value of 0 to read the first byte returned: + result = SPI.transfer(0x00); + // decrement the number of bytes left to read: + bytesToRead--; + // if you still have another byte to read: + if (bytesToRead > 0) { + // shift the first byte left, then get the second byte: + result = result << 8; + inByte = SPI.transfer(0x00); + // combine the byte you just got with the previous one: + result = result | inByte; + // decrement the number of bytes left to read: + bytesToRead--; + } + // take the chip select high to de-select: + digitalWrite(chipSelectPin, HIGH); + // return the result: + return(result); +} + + +//Sends a write command to SCP1000 + +void writeRegister(byte thisRegister, byte thisValue) { + + // SCP1000 expects the register address in the upper 6 bits + // of the byte. So shift the bits left by two bits: + thisRegister = thisRegister << 2; + // now combine the register address and the command into one byte: + dataToSend = thisRegister | WRITE; + + // take the chip select low to select the device: + digitalWrite(chipSelectPin, LOW); + + SPI.transfer(dataToSend); //Send register location + SPI.transfer(thisValue); //Send value to record into register + + // take the chip select high to de-select: + digitalWrite(chipSelectPin, HIGH); +} + + + diff --git a/libraries/SPI/examples/DigitalPotControl/DigitalPotControl.ino b/libraries/SPI/examples/DigitalPotControl/DigitalPotControl.ino new file mode 100644 index 0000000..ef97dae --- /dev/null +++ b/libraries/SPI/examples/DigitalPotControl/DigitalPotControl.ino @@ -0,0 +1,71 @@ +/* + Digital Pot Control + + This example controls an Analog Devices AD5206 digital potentiometer. + The AD5206 has 6 potentiometer channels. Each channel's pins are labeled + A - connect this to voltage + W - this is the pot's wiper, which changes when you set it + B - connect this to ground. + + The AD5206 is SPI-compatible,and to command it, you send two bytes, + one with the channel number (0 - 5) and one with the resistance value for the + channel (0 - 255). + + The circuit: + * All A pins of AD5206 connected to +5V + * All B pins of AD5206 connected to ground + * An LED and a 220-ohm resisor in series connected from each W pin to ground + * CS - to digital pin 10 (SS pin) + * SDI - to digital pin 11 (MOSI pin) + * CLK - to digital pin 13 (SCK pin) + + created 10 Aug 2010 + by Tom Igoe + + Thanks to Heather Dewey-Hagborg for the original tutorial, 2005 + +*/ + + +// inslude the SPI library: +#include <SPI.h> + + +// set pin 10 as the slave select for the digital pot: +const int slaveSelectPin = 10; + +void setup() { + // set the slaveSelectPin as an output: + pinMode (slaveSelectPin, OUTPUT); + // initialize SPI: + SPI.begin(); +} + +void loop() { + // go through the six channels of the digital pot: + for (int channel = 0; channel < 6; channel++) { + // change the resistance on this channel from min to max: + for (int level = 0; level < 255; level++) { + digitalPotWrite(channel, level); + delay(10); + } + // wait a second at the top: + delay(100); + // change the resistance on this channel from max to min: + for (int level = 0; level < 255; level++) { + digitalPotWrite(channel, 255 - level); + delay(10); + } + } + +} + +int digitalPotWrite(int address, int value) { + // take the SS pin low to select the chip: + digitalWrite(slaveSelectPin,LOW); + // send in the address and value via SPI: + SPI.transfer(address); + SPI.transfer(value); + // take the SS pin high to de-select the chip: + digitalWrite(slaveSelectPin,HIGH); +}
\ No newline at end of file |