aboutsummaryrefslogtreecommitdiff
path: root/libraries/SD/examples
diff options
context:
space:
mode:
Diffstat (limited to 'libraries/SD/examples')
-rw-r--r--libraries/SD/examples/CardInfo/CardInfo.ino117
-rw-r--r--libraries/SD/examples/Datalogger/Datalogger.ino92
-rw-r--r--libraries/SD/examples/DumpFile/DumpFile.ino73
-rw-r--r--libraries/SD/examples/Files/Files.ino84
-rw-r--r--libraries/SD/examples/ReadWrite/ReadWrite.ino85
-rw-r--r--libraries/SD/examples/listfiles/listfiles.ino83
6 files changed, 534 insertions, 0 deletions
diff --git a/libraries/SD/examples/CardInfo/CardInfo.ino b/libraries/SD/examples/CardInfo/CardInfo.ino
new file mode 100644
index 0000000..0c2dfc5
--- /dev/null
+++ b/libraries/SD/examples/CardInfo/CardInfo.ino
@@ -0,0 +1,117 @@
+/*
+ SD card test
+
+ This example shows how use the utility libraries on which the'
+ SD library is based in order to get info about your SD card.
+ Very useful for testing a card when you're not sure whether its working or not.
+
+ The circuit:
+ * SD card attached to SPI bus as follows:
+ ** MOSI - pin 11 on Arduino Uno/Duemilanove/Diecimila
+ ** MISO - pin 12 on Arduino Uno/Duemilanove/Diecimila
+ ** CLK - pin 13 on Arduino Uno/Duemilanove/Diecimila
+ ** CS - depends on your SD card shield or module.
+ Pin 4 used here for consistency with other Arduino examples
+
+
+ created 28 Mar 2011
+ by Limor Fried
+ modified 9 Apr 2012
+ by Tom Igoe
+ */
+ // include the SD library:
+#include <SD.h>
+
+// set up variables using the SD utility library functions:
+Sd2Card card;
+SdVolume volume;
+SdFile root;
+
+// change this to match your SD shield or module;
+// Arduino Ethernet shield: pin 4
+// Adafruit SD shields and modules: pin 10
+// Sparkfun SD shield: pin 8
+const int chipSelect = 4;
+
+void setup()
+{
+ // Open serial communications and wait for port to open:
+ Serial.begin(9600);
+ while (!Serial) {
+ ; // wait for serial port to connect. Needed for Leonardo only
+ }
+
+
+ Serial.print("\nInitializing SD card...");
+ // On the Ethernet Shield, CS is pin 4. It's set as an output by default.
+ // Note that even if it's not used as the CS pin, the hardware SS pin
+ // (10 on most Arduino boards, 53 on the Mega) must be left as an output
+ // or the SD library functions will not work.
+ pinMode(10, OUTPUT); // change this to 53 on a mega
+
+
+ // we'll use the initialization code from the utility libraries
+ // since we're just testing if the card is working!
+ if (!card.init(SPI_HALF_SPEED, chipSelect)) {
+ Serial.println("initialization failed. Things to check:");
+ Serial.println("* is a card is inserted?");
+ Serial.println("* Is your wiring correct?");
+ Serial.println("* did you change the chipSelect pin to match your shield or module?");
+ return;
+ } else {
+ Serial.println("Wiring is correct and a card is present.");
+ }
+
+ // print the type of card
+ Serial.print("\nCard type: ");
+ switch(card.type()) {
+ case SD_CARD_TYPE_SD1:
+ Serial.println("SD1");
+ break;
+ case SD_CARD_TYPE_SD2:
+ Serial.println("SD2");
+ break;
+ case SD_CARD_TYPE_SDHC:
+ Serial.println("SDHC");
+ break;
+ default:
+ Serial.println("Unknown");
+ }
+
+ // Now we will try to open the 'volume'/'partition' - it should be FAT16 or FAT32
+ if (!volume.init(card)) {
+ Serial.println("Could not find FAT16/FAT32 partition.\nMake sure you've formatted the card");
+ return;
+ }
+
+
+ // print the type and size of the first FAT-type volume
+ uint32_t volumesize;
+ Serial.print("\nVolume type is FAT");
+ Serial.println(volume.fatType(), DEC);
+ Serial.println();
+
+ volumesize = volume.blocksPerCluster(); // clusters are collections of blocks
+ volumesize *= volume.clusterCount(); // we'll have a lot of clusters
+ volumesize *= 512; // SD card blocks are always 512 bytes
+ Serial.print("Volume size (bytes): ");
+ Serial.println(volumesize);
+ Serial.print("Volume size (Kbytes): ");
+ volumesize /= 1024;
+ Serial.println(volumesize);
+ Serial.print("Volume size (Mbytes): ");
+ volumesize /= 1024;
+ Serial.println(volumesize);
+
+
+ Serial.println("\nFiles found on the card (name, date and size in bytes): ");
+ root.openRoot(volume);
+
+ // list all files in the card with date and size
+ root.ls(LS_R | LS_DATE | LS_SIZE);
+}
+
+
+void loop(void) {
+
+}
diff --git a/libraries/SD/examples/Datalogger/Datalogger.ino b/libraries/SD/examples/Datalogger/Datalogger.ino
new file mode 100644
index 0000000..a7f85ee
--- /dev/null
+++ b/libraries/SD/examples/Datalogger/Datalogger.ino
@@ -0,0 +1,92 @@
+/*
+ SD card datalogger
+
+ This example shows how to log data from three analog sensors
+ to an SD card using the SD library.
+
+ The circuit:
+ * analog sensors on analog ins 0, 1, and 2
+ * SD card attached to SPI bus as follows:
+ ** MOSI - pin 11
+ ** MISO - pin 12
+ ** CLK - pin 13
+ ** CS - pin 4
+
+ created 24 Nov 2010
+ modified 9 Apr 2012
+ by Tom Igoe
+
+ This example code is in the public domain.
+
+ */
+
+#include <SD.h>
+
+// On the Ethernet Shield, CS is pin 4. Note that even if it's not
+// used as the CS pin, the hardware CS pin (10 on most Arduino boards,
+// 53 on the Mega) must be left as an output or the SD library
+// functions will not work.
+const int chipSelect = 4;
+
+void setup()
+{
+ // Open serial communications and wait for port to open:
+ Serial.begin(9600);
+ while (!Serial) {
+ ; // wait for serial port to connect. Needed for Leonardo only
+ }
+
+
+ Serial.print("Initializing SD card...");
+ // make sure that the default chip select pin is set to
+ // output, even if you don't use it:
+ pinMode(10, OUTPUT);
+
+ // see if the card is present and can be initialized:
+ if (!SD.begin(chipSelect)) {
+ Serial.println("Card failed, or not present");
+ // don't do anything more:
+ return;
+ }
+ Serial.println("card initialized.");
+}
+
+void loop()
+{
+ // make a string for assembling the data to log:
+ String dataString = "";
+
+ // read three sensors and append to the string:
+ for (int analogPin = 0; analogPin < 3; analogPin++) {
+ int sensor = analogRead(analogPin);
+ dataString += String(sensor);
+ if (analogPin < 2) {
+ dataString += ",";
+ }
+ }
+
+ // open the file. note that only one file can be open at a time,
+ // so you have to close this one before opening another.
+ File dataFile = SD.open("datalog.txt", FILE_WRITE);
+
+ // if the file is available, write to it:
+ if (dataFile) {
+ dataFile.println(dataString);
+ dataFile.close();
+ // print to the serial port too:
+ Serial.println(dataString);
+ }
+ // if the file isn't open, pop up an error:
+ else {
+ Serial.println("error opening datalog.txt");
+ }
+}
+
+
+
+
+
+
+
+
+
diff --git a/libraries/SD/examples/DumpFile/DumpFile.ino b/libraries/SD/examples/DumpFile/DumpFile.ino
new file mode 100644
index 0000000..d83089a
--- /dev/null
+++ b/libraries/SD/examples/DumpFile/DumpFile.ino
@@ -0,0 +1,73 @@
+/*
+ SD card file dump
+
+ This example shows how to read a file from the SD card using the
+ SD library and send it over the serial port.
+
+ The circuit:
+ * SD card attached to SPI bus as follows:
+ ** MOSI - pin 11
+ ** MISO - pin 12
+ ** CLK - pin 13
+ ** CS - pin 4
+
+ created 22 December 2010
+ by Limor Fried
+ modified 9 Apr 2012
+ by Tom Igoe
+
+ This example code is in the public domain.
+
+ */
+
+#include <SD.h>
+
+// On the Ethernet Shield, CS is pin 4. Note that even if it's not
+// used as the CS pin, the hardware CS pin (10 on most Arduino boards,
+// 53 on the Mega) must be left as an output or the SD library
+// functions will not work.
+const int chipSelect = 4;
+
+void setup()
+{
+ // Open serial communications and wait for port to open:
+ Serial.begin(9600);
+ while (!Serial) {
+ ; // wait for serial port to connect. Needed for Leonardo only
+ }
+
+
+ Serial.print("Initializing SD card...");
+ // make sure that the default chip select pin is set to
+ // output, even if you don't use it:
+ pinMode(10, OUTPUT);
+
+ // see if the card is present and can be initialized:
+ if (!SD.begin(chipSelect)) {
+ Serial.println("Card failed, or not present");
+ // don't do anything more:
+ return;
+ }
+ Serial.println("card initialized.");
+
+ // open the file. note that only one file can be open at a time,
+ // so you have to close this one before opening another.
+ File dataFile = SD.open("datalog.txt");
+
+ // if the file is available, write to it:
+ if (dataFile) {
+ while (dataFile.available()) {
+ Serial.write(dataFile.read());
+ }
+ dataFile.close();
+ }
+ // if the file isn't open, pop up an error:
+ else {
+ Serial.println("error opening datalog.txt");
+ }
+}
+
+void loop()
+{
+}
+
diff --git a/libraries/SD/examples/Files/Files.ino b/libraries/SD/examples/Files/Files.ino
new file mode 100644
index 0000000..a15b862
--- /dev/null
+++ b/libraries/SD/examples/Files/Files.ino
@@ -0,0 +1,84 @@
+/*
+ SD card basic file example
+
+ This example shows how to create and destroy an SD card file
+ The circuit:
+ * SD card attached to SPI bus as follows:
+ ** MOSI - pin 11
+ ** MISO - pin 12
+ ** CLK - pin 13
+ ** CS - pin 4
+
+ created Nov 2010
+ by David A. Mellis
+ modified 9 Apr 2012
+ by Tom Igoe
+
+ This example code is in the public domain.
+
+ */
+#include <SD.h>
+
+File myFile;
+
+void setup()
+{
+ // Open serial communications and wait for port to open:
+ Serial.begin(9600);
+ while (!Serial) {
+ ; // wait for serial port to connect. Needed for Leonardo only
+ }
+
+
+ Serial.print("Initializing SD card...");
+ // On the Ethernet Shield, CS is pin 4. It's set as an output by default.
+ // Note that even if it's not used as the CS pin, the hardware SS pin
+ // (10 on most Arduino boards, 53 on the Mega) must be left as an output
+ // or the SD library functions will not work.
+ pinMode(10, OUTPUT);
+
+ if (!SD.begin(4)) {
+ Serial.println("initialization failed!");
+ return;
+ }
+ Serial.println("initialization done.");
+
+ if (SD.exists("example.txt")) {
+ Serial.println("example.txt exists.");
+ }
+ else {
+ Serial.println("example.txt doesn't exist.");
+ }
+
+ // open a new file and immediately close it:
+ Serial.println("Creating example.txt...");
+ myFile = SD.open("example.txt", FILE_WRITE);
+ myFile.close();
+
+ // Check to see if the file exists:
+ if (SD.exists("example.txt")) {
+ Serial.println("example.txt exists.");
+ }
+ else {
+ Serial.println("example.txt doesn't exist.");
+ }
+
+ // delete the file:
+ Serial.println("Removing example.txt...");
+ SD.remove("example.txt");
+
+ if (SD.exists("example.txt")){
+ Serial.println("example.txt exists.");
+ }
+ else {
+ Serial.println("example.txt doesn't exist.");
+ }
+}
+
+void loop()
+{
+ // nothing happens after setup finishes.
+}
+
+
+
diff --git a/libraries/SD/examples/ReadWrite/ReadWrite.ino b/libraries/SD/examples/ReadWrite/ReadWrite.ino
new file mode 100644
index 0000000..5805fc8
--- /dev/null
+++ b/libraries/SD/examples/ReadWrite/ReadWrite.ino
@@ -0,0 +1,85 @@
+/*
+ SD card read/write
+
+ This example shows how to read and write data to and from an SD card file
+ The circuit:
+ * SD card attached to SPI bus as follows:
+ ** MOSI - pin 11
+ ** MISO - pin 12
+ ** CLK - pin 13
+ ** CS - pin 4
+
+ created Nov 2010
+ by David A. Mellis
+ modified 9 Apr 2012
+ by Tom Igoe
+
+ This example code is in the public domain.
+
+ */
+
+#include <SD.h>
+
+File myFile;
+
+void setup()
+{
+ // Open serial communications and wait for port to open:
+ Serial.begin(9600);
+ while (!Serial) {
+ ; // wait for serial port to connect. Needed for Leonardo only
+ }
+
+
+ Serial.print("Initializing SD card...");
+ // On the Ethernet Shield, CS is pin 4. It's set as an output by default.
+ // Note that even if it's not used as the CS pin, the hardware SS pin
+ // (10 on most Arduino boards, 53 on the Mega) must be left as an output
+ // or the SD library functions will not work.
+ pinMode(10, OUTPUT);
+
+ if (!SD.begin(4)) {
+ Serial.println("initialization failed!");
+ return;
+ }
+ Serial.println("initialization done.");
+
+ // open the file. note that only one file can be open at a time,
+ // so you have to close this one before opening another.
+ myFile = SD.open("test.txt", FILE_WRITE);
+
+ // if the file opened okay, write to it:
+ if (myFile) {
+ Serial.print("Writing to test.txt...");
+ myFile.println("testing 1, 2, 3.");
+ // close the file:
+ myFile.close();
+ Serial.println("done.");
+ } else {
+ // if the file didn't open, print an error:
+ Serial.println("error opening test.txt");
+ }
+
+ // re-open the file for reading:
+ myFile = SD.open("test.txt");
+ if (myFile) {
+ Serial.println("test.txt:");
+
+ // read from the file until there's nothing else in it:
+ while (myFile.available()) {
+ Serial.write(myFile.read());
+ }
+ // close the file:
+ myFile.close();
+ } else {
+ // if the file didn't open, print an error:
+ Serial.println("error opening test.txt");
+ }
+}
+
+void loop()
+{
+ // nothing happens after setup
+}
+
+
diff --git a/libraries/SD/examples/listfiles/listfiles.ino b/libraries/SD/examples/listfiles/listfiles.ino
new file mode 100644
index 0000000..876c3f8
--- /dev/null
+++ b/libraries/SD/examples/listfiles/listfiles.ino
@@ -0,0 +1,83 @@
+/*
+ SD card basic file example
+
+ This example shows how to create and destroy an SD card file
+ The circuit:
+ * SD card attached to SPI bus as follows:
+ ** MOSI - pin 11
+ ** MISO - pin 12
+ ** CLK - pin 13
+ ** CS - pin 4
+
+ created Nov 2010
+ by David A. Mellis
+ modified 9 Apr 2012
+ by Tom Igoe
+
+ This example code is in the public domain.
+
+ */
+#include <SD.h>
+
+File root;
+
+void setup()
+{
+ // Open serial communications and wait for port to open:
+ Serial.begin(9600);
+ while (!Serial) {
+ ; // wait for serial port to connect. Needed for Leonardo only
+ }
+
+
+ Serial.print("Initializing SD card...");
+ // On the Ethernet Shield, CS is pin 4. It's set as an output by default.
+ // Note that even if it's not used as the CS pin, the hardware SS pin
+ // (10 on most Arduino boards, 53 on the Mega) must be left as an output
+ // or the SD library functions will not work.
+ pinMode(10, OUTPUT);
+
+ if (!SD.begin(10)) {
+ Serial.println("initialization failed!");
+ return;
+ }
+ Serial.println("initialization done.");
+
+ root = SD.open("/");
+
+ printDirectory(root, 0);
+
+ Serial.println("done!");
+}
+
+void loop()
+{
+ // nothing happens after setup finishes.
+}
+
+void printDirectory(File dir, int numTabs) {
+ while(true) {
+
+ File entry = dir.openNextFile();
+ if (! entry) {
+ // no more files
+ //Serial.println("**nomorefiles**");
+ break;
+ }
+ for (uint8_t i=0; i<numTabs; i++) {
+ Serial.print('\t');
+ }
+ Serial.print(entry.name());
+ if (entry.isDirectory()) {
+ Serial.println("/");
+ printDirectory(entry, numTabs+1);
+ } else {
+ // files have sizes, directories do not
+ Serial.print("\t\t");
+ Serial.println(entry.size(), DEC);
+ }
+ }
+}
+
+
+
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-11-23 07:02:00 +0000