diff options
Diffstat (limited to 'libraries/Firmata/examples')
14 files changed, 0 insertions, 2808 deletions
diff --git a/libraries/Firmata/examples/AnalogFirmata/AnalogFirmata.pde b/libraries/Firmata/examples/AnalogFirmata/AnalogFirmata.pde deleted file mode 100644 index ab83726..0000000 --- a/libraries/Firmata/examples/AnalogFirmata/AnalogFirmata.pde +++ /dev/null @@ -1,83 +0,0 @@ -/* This firmware supports as many analog ports as possible, all analog inputs, - * four PWM outputs, and two with servo support. - * - * This example code is in the public domain. - */ -#include <Firmata.h> -#include <Servo.h> - -/*============================================================================== - * GLOBAL VARIABLES - *============================================================================*/ - -/* servos */ -Servo servo9, servo10; // one instance per pin -/* analog inputs */ -int analogInputsToReport = 0; // bitwise array to store pin reporting -int analogPin = 0; // counter for reading analog pins -/* timer variables */ -unsigned long currentMillis; // store the current value from millis() -unsigned long nextExecuteMillis; // for comparison with currentMillis - - -/*============================================================================== - * FUNCTIONS - *============================================================================*/ - -void analogWriteCallback(byte pin, int value) -{ - switch(pin) { - case 9: servo9.write(value); break; - case 10: servo10.write(value); break; - case 3: - case 5: - case 6: - case 11: // PWM pins - analogWrite(pin, value); - break; - } -} -// ----------------------------------------------------------------------------- -// sets bits in a bit array (int) to toggle the reporting of the analogIns -void reportAnalogCallback(byte pin, int value) -{ - if(value == 0) { - analogInputsToReport = analogInputsToReport &~ (1 << pin); - } - else { // everything but 0 enables reporting of that pin - analogInputsToReport = analogInputsToReport | (1 << pin); - } - // TODO: save status to EEPROM here, if changed -} - -/*============================================================================== - * SETUP() - *============================================================================*/ -void setup() -{ - Firmata.setFirmwareVersion(0, 2); - Firmata.attach(ANALOG_MESSAGE, analogWriteCallback); - Firmata.attach(REPORT_ANALOG, reportAnalogCallback); - - servo9.attach(9); - servo10.attach(10); - Firmata.begin(57600); -} - -/*============================================================================== - * LOOP() - *============================================================================*/ -void loop() -{ - while(Firmata.available()) - Firmata.processInput(); - currentMillis = millis(); - if(currentMillis > nextExecuteMillis) { - nextExecuteMillis = currentMillis + 19; // run this every 20ms - for(analogPin=0;analogPin<TOTAL_ANALOG_PINS;analogPin++) { - if( analogInputsToReport & (1 << analogPin) ) - Firmata.sendAnalog(analogPin, analogRead(analogPin)); - } - } -} - diff --git a/libraries/Firmata/examples/AnalogFirmata/Makefile b/libraries/Firmata/examples/AnalogFirmata/Makefile deleted file mode 100644 index e968c0a..0000000 --- a/libraries/Firmata/examples/AnalogFirmata/Makefile +++ /dev/null @@ -1,263 +0,0 @@ -# Arduino makefile -# -# This makefile allows you to build sketches from the command line -# without the Arduino environment (or Java). -# -# The Arduino environment does preliminary processing on a sketch before -# compiling it. If you're using this makefile instead, you'll need to do -# a few things differently: -# -# - Give your program's file a .cpp extension (e.g. foo.cpp). -# -# - Put this line at top of your code: #include <WProgram.h> -# -# - Write prototypes for all your functions (or define them before you -# call them). A prototype declares the types of parameters a -# function will take and what type of value it will return. This -# means that you can have a call to a function before the definition -# of the function. A function prototype looks like the first line of -# the function, with a semi-colon at the end. For example: -# int digitalRead(int pin); -# -# Instructions for using the makefile: -# -# 1. Copy this file into the folder with your sketch. -# -# 2. Below, modify the line containing "TARGET" to refer to the name of -# of your program's file without an extension (e.g. TARGET = foo). -# -# 3. Modify the line containg "ARDUINO" to point the directory that -# contains the Arduino core (for normal Arduino installations, this -# is the hardware/cores/arduino sub-directory). -# -# 4. Modify the line containing "PORT" to refer to the filename -# representing the USB or serial connection to your Arduino board -# (e.g. PORT = /dev/tty.USB0). If the exact name of this file -# changes, you can use * as a wildcard (e.g. PORT = /dev/tty.USB*). -# -# 5. At the command line, change to the directory containing your -# program's file and the makefile. -# -# 6. Type "make" and press enter to compile/verify your program. -# -# 7. Type "make upload", reset your Arduino board, and press enter to -# upload your program to the Arduino board. -# -# $Id: Makefile,v 1.7 2007/04/13 05:28:23 eighthave Exp $ - -PORT = /dev/tty.usbserial-* -TARGET := $(shell pwd | sed 's|.*/\(.*\)|\1|') -ARDUINO = /Applications/arduino -ARDUINO_SRC = $(ARDUINO)/hardware/cores/arduino -ARDUINO_LIB_SRC = $(ARDUINO)/hardware/libraries -INCLUDE = -I$(ARDUINO_SRC) -I$(ARDUINO)/hardware/tools/avr/avr/include \ - -I$(ARDUINO_LIB_SRC)/EEPROM \ - -I$(ARDUINO_LIB_SRC)/Firmata \ - -I$(ARDUINO_LIB_SRC)/Servo \ - -I$(ARDUINO_LIB_SRC) -SRC = $(wildcard $(ARDUINO_SRC)/*.c) -CXXSRC = applet/$(TARGET).cpp $(ARDUINO_SRC)/HardwareSerial.cpp \ - $(ARDUINO_LIB_SRC)/EEPROM/EEPROM.cpp \ - $(ARDUINO_LIB_SRC)/Firmata/Firmata.cpp \ - $(ARDUINO_LIB_SRC)/Servo/Servo.cpp \ - $(ARDUINO_SRC)/WMath.cpp -HEADERS = $(wildcard $(ARDUINO_SRC)/*.h) $(wildcard $(ARDUINO_LIB_SRC)/*/*.h) - -MCU = atmega168 -#MCU = atmega8 -F_CPU = 16000000 -FORMAT = ihex -UPLOAD_RATE = 19200 - -# Name of this Makefile (used for "make depend"). -MAKEFILE = Makefile - -# Debugging format. -# Native formats for AVR-GCC's -g are stabs [default], or dwarf-2. -# AVR (extended) COFF requires stabs, plus an avr-objcopy run. -DEBUG = stabs - -OPT = s - -# Place -D or -U options here -CDEFS = -DF_CPU=$(F_CPU) -CXXDEFS = -DF_CPU=$(F_CPU) - -# Compiler flag to set the C Standard level. -# c89 - "ANSI" C -# gnu89 - c89 plus GCC extensions -# c99 - ISO C99 standard (not yet fully implemented) -# gnu99 - c99 plus GCC extensions -CSTANDARD = -std=gnu99 -CDEBUG = -g$(DEBUG) -CWARN = -Wall -Wstrict-prototypes -CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums -#CEXTRA = -Wa,-adhlns=$(<:.c=.lst) - -CFLAGS = $(CDEBUG) $(CDEFS) $(INCLUDE) -O$(OPT) $(CWARN) $(CSTANDARD) $(CEXTRA) -CXXFLAGS = $(CDEFS) $(INCLUDE) -O$(OPT) -#ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs -LDFLAGS = - - -# Programming support using avrdude. Settings and variables. -AVRDUDE_PROGRAMMER = stk500 -AVRDUDE_PORT = $(PORT) -AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex -AVRDUDE_FLAGS = -F -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) \ - -b $(UPLOAD_RATE) -q -V - -# Program settings -CC = avr-gcc -CXX = avr-g++ -OBJCOPY = avr-objcopy -OBJDUMP = avr-objdump -SIZE = avr-size -NM = avr-nm -AVRDUDE = avrdude -REMOVE = rm -f -MV = mv -f - -# Define all object files. -OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o) - -# Define all listing files. -LST = $(ASRC:.S=.lst) $(CXXSRC:.cpp=.lst) $(SRC:.c=.lst) - -# Combine all necessary flags and optional flags. -# Add target processor to flags. -ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) -ALL_CXXFLAGS = -mmcu=$(MCU) -I. $(CXXFLAGS) -ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS) - - -# Default target. -all: build - -build: applet/$(TARGET).hex - -eep: applet/$(TARGET).eep -lss: applet/$(TARGET).lss -sym: applet/$(TARGET).sym - - -# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB. -COFFCONVERT=$(OBJCOPY) --debugging \ ---change-section-address .data-0x800000 \ ---change-section-address .bss-0x800000 \ ---change-section-address .noinit-0x800000 \ ---change-section-address .eeprom-0x810000 - - -coff: applet/$(TARGET).elf - $(COFFCONVERT) -O coff-avr applet/$(TARGET).elf applet/$(TARGET).cof - - -extcoff: applet/$(TARGET).elf - $(COFFCONVERT) -O coff-ext-avr applet/$(TARGET).elf applet/$(TARGET).cof - - -.SUFFIXES: .elf .hex .eep .lss .sym .pde - -.elf.hex: - $(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@ - -.elf.eep: - -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \ - --change-section-lma .eeprom=0 -O $(FORMAT) $< $@ - -# Create extended listing file from ELF output file. -.elf.lss: - $(OBJDUMP) -h -S $< > $@ - -# Create a symbol table from ELF output file. -.elf.sym: - $(NM) -n $< > $@ - - -# Compile: create object files from C++ source files. -.cpp.o: $(HEADERS) - $(CXX) -c $(ALL_CXXFLAGS) $< -o $@ - -# Compile: create object files from C source files. -.c.o: $(HEADERS) - $(CC) -c $(ALL_CFLAGS) $< -o $@ - - -# Compile: create assembler files from C source files. -.c.s: - $(CC) -S $(ALL_CFLAGS) $< -o $@ - - -# Assemble: create object files from assembler source files. -.S.o: - $(CC) -c $(ALL_ASFLAGS) $< -o $@ - - - -applet/$(TARGET).cpp: $(TARGET).pde - test -d applet || mkdir applet - echo '#include "WProgram.h"' > applet/$(TARGET).cpp - echo '#include "avr/interrupt.h"' >> applet/$(TARGET).cpp - sed -n 's|^\(void .*)\).*|\1;|p' $(TARGET).pde | grep -v 'setup()' | \ - grep -v 'loop()' >> applet/$(TARGET).cpp - cat $(TARGET).pde >> applet/$(TARGET).cpp - cat $(ARDUINO_SRC)/main.cxx >> applet/$(TARGET).cpp - -# Link: create ELF output file from object files. -applet/$(TARGET).elf: applet/$(TARGET).cpp $(OBJ) - $(CC) $(ALL_CFLAGS) $(OBJ) --output $@ $(LDFLAGS) - -pd_close_serial: - echo 'close;' | /Applications/Pd-extended.app/Contents/Resources/bin/pdsend 34567 || true - -# Program the device. -upload: applet/$(TARGET).hex - $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) - - -pd_test: build pd_close_serial upload - -# Target: clean project. -clean: - $(REMOVE) -- applet/$(TARGET).hex applet/$(TARGET).eep \ - applet/$(TARGET).cof applet/$(TARGET).elf $(TARGET).map \ - applet/$(TARGET).sym applet/$(TARGET).lss applet/$(TARGET).cpp \ - $(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d) - rmdir -- applet - -depend: - if grep '^# DO NOT DELETE' $(MAKEFILE) >/dev/null; \ - then \ - sed -e '/^# DO NOT DELETE/,$$d' $(MAKEFILE) > \ - $(MAKEFILE).$$$$ && \ - $(MV) $(MAKEFILE).$$$$ $(MAKEFILE); \ - fi - echo '# DO NOT DELETE THIS LINE -- make depend depends on it.' \ - >> $(MAKEFILE); \ - $(CC) -M -mmcu=$(MCU) $(CDEFS) $(INCLUDE) $(SRC) $(ASRC) >> $(MAKEFILE) - -.PHONY: all build eep lss sym coff extcoff clean depend pd_close_serial pd_test - -# for emacs -etags: - make etags_`uname -s` - etags *.pde \ - $(ARDUINO_SRC)/*.[ch] \ - $(ARDUINO_SRC)/*.cpp \ - $(ARDUINO_LIB_SRC)/*/*.[ch] \ - $(ARDUINO_LIB_SRC)/*/*.cpp \ - $(ARDUINO)/hardware/tools/avr/avr/include/avr/*.[ch] \ - $(ARDUINO)/hardware/tools/avr/avr/include/*.[ch] - -etags_Darwin: -# etags -a - -etags_Linux: -# etags -a /usr/include/*.h linux/input.h /usr/include/sys/*.h - -etags_MINGW: -# etags -a /usr/include/*.h /usr/include/sys/*.h - - - diff --git a/libraries/Firmata/examples/EchoString/EchoString.pde b/libraries/Firmata/examples/EchoString/EchoString.pde deleted file mode 100644 index 6559ae1..0000000 --- a/libraries/Firmata/examples/EchoString/EchoString.pde +++ /dev/null @@ -1,40 +0,0 @@ -/* This sketch accepts strings and raw sysex messages and echos them back. - * - * This example code is in the public domain. - */ -#include <Firmata.h> - -byte analogPin; - -void stringCallback(char *myString) -{ - Firmata.sendString(myString); -} - - -void sysexCallback(byte command, byte argc, byte*argv) -{ - Serial.print(START_SYSEX, BYTE); - Serial.print(command, BYTE); - for(byte i=0; i<argc; i++) { - Serial.print(argv[i], BYTE); - } - Serial.print(END_SYSEX, BYTE); -} - -void setup() -{ - Firmata.setFirmwareVersion(0, 1); - Firmata.attach(STRING_DATA, stringCallback); - Firmata.attach(START_SYSEX, sysexCallback); - Firmata.begin(57600); -} - -void loop() -{ - while(Firmata.available()) { - Firmata.processInput(); - } -} - - diff --git a/libraries/Firmata/examples/EchoString/Makefile b/libraries/Firmata/examples/EchoString/Makefile deleted file mode 100644 index e968c0a..0000000 --- a/libraries/Firmata/examples/EchoString/Makefile +++ /dev/null @@ -1,263 +0,0 @@ -# Arduino makefile -# -# This makefile allows you to build sketches from the command line -# without the Arduino environment (or Java). -# -# The Arduino environment does preliminary processing on a sketch before -# compiling it. If you're using this makefile instead, you'll need to do -# a few things differently: -# -# - Give your program's file a .cpp extension (e.g. foo.cpp). -# -# - Put this line at top of your code: #include <WProgram.h> -# -# - Write prototypes for all your functions (or define them before you -# call them). A prototype declares the types of parameters a -# function will take and what type of value it will return. This -# means that you can have a call to a function before the definition -# of the function. A function prototype looks like the first line of -# the function, with a semi-colon at the end. For example: -# int digitalRead(int pin); -# -# Instructions for using the makefile: -# -# 1. Copy this file into the folder with your sketch. -# -# 2. Below, modify the line containing "TARGET" to refer to the name of -# of your program's file without an extension (e.g. TARGET = foo). -# -# 3. Modify the line containg "ARDUINO" to point the directory that -# contains the Arduino core (for normal Arduino installations, this -# is the hardware/cores/arduino sub-directory). -# -# 4. Modify the line containing "PORT" to refer to the filename -# representing the USB or serial connection to your Arduino board -# (e.g. PORT = /dev/tty.USB0). If the exact name of this file -# changes, you can use * as a wildcard (e.g. PORT = /dev/tty.USB*). -# -# 5. At the command line, change to the directory containing your -# program's file and the makefile. -# -# 6. Type "make" and press enter to compile/verify your program. -# -# 7. Type "make upload", reset your Arduino board, and press enter to -# upload your program to the Arduino board. -# -# $Id: Makefile,v 1.7 2007/04/13 05:28:23 eighthave Exp $ - -PORT = /dev/tty.usbserial-* -TARGET := $(shell pwd | sed 's|.*/\(.*\)|\1|') -ARDUINO = /Applications/arduino -ARDUINO_SRC = $(ARDUINO)/hardware/cores/arduino -ARDUINO_LIB_SRC = $(ARDUINO)/hardware/libraries -INCLUDE = -I$(ARDUINO_SRC) -I$(ARDUINO)/hardware/tools/avr/avr/include \ - -I$(ARDUINO_LIB_SRC)/EEPROM \ - -I$(ARDUINO_LIB_SRC)/Firmata \ - -I$(ARDUINO_LIB_SRC)/Servo \ - -I$(ARDUINO_LIB_SRC) -SRC = $(wildcard $(ARDUINO_SRC)/*.c) -CXXSRC = applet/$(TARGET).cpp $(ARDUINO_SRC)/HardwareSerial.cpp \ - $(ARDUINO_LIB_SRC)/EEPROM/EEPROM.cpp \ - $(ARDUINO_LIB_SRC)/Firmata/Firmata.cpp \ - $(ARDUINO_LIB_SRC)/Servo/Servo.cpp \ - $(ARDUINO_SRC)/WMath.cpp -HEADERS = $(wildcard $(ARDUINO_SRC)/*.h) $(wildcard $(ARDUINO_LIB_SRC)/*/*.h) - -MCU = atmega168 -#MCU = atmega8 -F_CPU = 16000000 -FORMAT = ihex -UPLOAD_RATE = 19200 - -# Name of this Makefile (used for "make depend"). -MAKEFILE = Makefile - -# Debugging format. -# Native formats for AVR-GCC's -g are stabs [default], or dwarf-2. -# AVR (extended) COFF requires stabs, plus an avr-objcopy run. -DEBUG = stabs - -OPT = s - -# Place -D or -U options here -CDEFS = -DF_CPU=$(F_CPU) -CXXDEFS = -DF_CPU=$(F_CPU) - -# Compiler flag to set the C Standard level. -# c89 - "ANSI" C -# gnu89 - c89 plus GCC extensions -# c99 - ISO C99 standard (not yet fully implemented) -# gnu99 - c99 plus GCC extensions -CSTANDARD = -std=gnu99 -CDEBUG = -g$(DEBUG) -CWARN = -Wall -Wstrict-prototypes -CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums -#CEXTRA = -Wa,-adhlns=$(<:.c=.lst) - -CFLAGS = $(CDEBUG) $(CDEFS) $(INCLUDE) -O$(OPT) $(CWARN) $(CSTANDARD) $(CEXTRA) -CXXFLAGS = $(CDEFS) $(INCLUDE) -O$(OPT) -#ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs -LDFLAGS = - - -# Programming support using avrdude. Settings and variables. -AVRDUDE_PROGRAMMER = stk500 -AVRDUDE_PORT = $(PORT) -AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex -AVRDUDE_FLAGS = -F -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) \ - -b $(UPLOAD_RATE) -q -V - -# Program settings -CC = avr-gcc -CXX = avr-g++ -OBJCOPY = avr-objcopy -OBJDUMP = avr-objdump -SIZE = avr-size -NM = avr-nm -AVRDUDE = avrdude -REMOVE = rm -f -MV = mv -f - -# Define all object files. -OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o) - -# Define all listing files. -LST = $(ASRC:.S=.lst) $(CXXSRC:.cpp=.lst) $(SRC:.c=.lst) - -# Combine all necessary flags and optional flags. -# Add target processor to flags. -ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) -ALL_CXXFLAGS = -mmcu=$(MCU) -I. $(CXXFLAGS) -ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS) - - -# Default target. -all: build - -build: applet/$(TARGET).hex - -eep: applet/$(TARGET).eep -lss: applet/$(TARGET).lss -sym: applet/$(TARGET).sym - - -# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB. -COFFCONVERT=$(OBJCOPY) --debugging \ ---change-section-address .data-0x800000 \ ---change-section-address .bss-0x800000 \ ---change-section-address .noinit-0x800000 \ ---change-section-address .eeprom-0x810000 - - -coff: applet/$(TARGET).elf - $(COFFCONVERT) -O coff-avr applet/$(TARGET).elf applet/$(TARGET).cof - - -extcoff: applet/$(TARGET).elf - $(COFFCONVERT) -O coff-ext-avr applet/$(TARGET).elf applet/$(TARGET).cof - - -.SUFFIXES: .elf .hex .eep .lss .sym .pde - -.elf.hex: - $(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@ - -.elf.eep: - -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \ - --change-section-lma .eeprom=0 -O $(FORMAT) $< $@ - -# Create extended listing file from ELF output file. -.elf.lss: - $(OBJDUMP) -h -S $< > $@ - -# Create a symbol table from ELF output file. -.elf.sym: - $(NM) -n $< > $@ - - -# Compile: create object files from C++ source files. -.cpp.o: $(HEADERS) - $(CXX) -c $(ALL_CXXFLAGS) $< -o $@ - -# Compile: create object files from C source files. -.c.o: $(HEADERS) - $(CC) -c $(ALL_CFLAGS) $< -o $@ - - -# Compile: create assembler files from C source files. -.c.s: - $(CC) -S $(ALL_CFLAGS) $< -o $@ - - -# Assemble: create object files from assembler source files. -.S.o: - $(CC) -c $(ALL_ASFLAGS) $< -o $@ - - - -applet/$(TARGET).cpp: $(TARGET).pde - test -d applet || mkdir applet - echo '#include "WProgram.h"' > applet/$(TARGET).cpp - echo '#include "avr/interrupt.h"' >> applet/$(TARGET).cpp - sed -n 's|^\(void .*)\).*|\1;|p' $(TARGET).pde | grep -v 'setup()' | \ - grep -v 'loop()' >> applet/$(TARGET).cpp - cat $(TARGET).pde >> applet/$(TARGET).cpp - cat $(ARDUINO_SRC)/main.cxx >> applet/$(TARGET).cpp - -# Link: create ELF output file from object files. -applet/$(TARGET).elf: applet/$(TARGET).cpp $(OBJ) - $(CC) $(ALL_CFLAGS) $(OBJ) --output $@ $(LDFLAGS) - -pd_close_serial: - echo 'close;' | /Applications/Pd-extended.app/Contents/Resources/bin/pdsend 34567 || true - -# Program the device. -upload: applet/$(TARGET).hex - $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) - - -pd_test: build pd_close_serial upload - -# Target: clean project. -clean: - $(REMOVE) -- applet/$(TARGET).hex applet/$(TARGET).eep \ - applet/$(TARGET).cof applet/$(TARGET).elf $(TARGET).map \ - applet/$(TARGET).sym applet/$(TARGET).lss applet/$(TARGET).cpp \ - $(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d) - rmdir -- applet - -depend: - if grep '^# DO NOT DELETE' $(MAKEFILE) >/dev/null; \ - then \ - sed -e '/^# DO NOT DELETE/,$$d' $(MAKEFILE) > \ - $(MAKEFILE).$$$$ && \ - $(MV) $(MAKEFILE).$$$$ $(MAKEFILE); \ - fi - echo '# DO NOT DELETE THIS LINE -- make depend depends on it.' \ - >> $(MAKEFILE); \ - $(CC) -M -mmcu=$(MCU) $(CDEFS) $(INCLUDE) $(SRC) $(ASRC) >> $(MAKEFILE) - -.PHONY: all build eep lss sym coff extcoff clean depend pd_close_serial pd_test - -# for emacs -etags: - make etags_`uname -s` - etags *.pde \ - $(ARDUINO_SRC)/*.[ch] \ - $(ARDUINO_SRC)/*.cpp \ - $(ARDUINO_LIB_SRC)/*/*.[ch] \ - $(ARDUINO_LIB_SRC)/*/*.cpp \ - $(ARDUINO)/hardware/tools/avr/avr/include/avr/*.[ch] \ - $(ARDUINO)/hardware/tools/avr/avr/include/*.[ch] - -etags_Darwin: -# etags -a - -etags_Linux: -# etags -a /usr/include/*.h linux/input.h /usr/include/sys/*.h - -etags_MINGW: -# etags -a /usr/include/*.h /usr/include/sys/*.h - - - diff --git a/libraries/Firmata/examples/I2CFirmata/I2CFirmata.pde b/libraries/Firmata/examples/I2CFirmata/I2CFirmata.pde deleted file mode 100644 index 796a8d5..0000000 --- a/libraries/Firmata/examples/I2CFirmata/I2CFirmata.pde +++ /dev/null @@ -1,217 +0,0 @@ -/* - Copyright (C) 2009 Jeff Hoefs. All rights reserved. - Copyright (C) 2009 Shigeru Kobayashi. All rights reserved. - - This library is free software; you can redistribute it and/or - modify it under the terms of the GNU Lesser General Public - License as published by the Free Software Foundation; either - version 2.1 of the License, or (at your option) any later version. - - See file LICENSE.txt for further informations on licensing terms. - */ - -#include <Wire.h> -#include <Firmata.h> - - -#define I2C_WRITE B00000000 -#define I2C_READ B00001000 -#define I2C_READ_CONTINUOUSLY B00010000 -#define I2C_STOP_READING B00011000 -#define I2C_READ_WRITE_MODE_MASK B00011000 - -#define MAX_QUERIES 8 - -unsigned long currentMillis; // store the current value from millis() -unsigned long nextExecuteMillis; // for comparison with currentMillis -unsigned int samplingInterval = 32; // default sampling interval is 33ms -unsigned int i2cReadDelayTime = 0; // default delay time between i2c read request and Wire.requestFrom() -unsigned int powerPinsEnabled = 0; // use as boolean to prevent enablePowerPins from being called more than once - -#define MINIMUM_SAMPLING_INTERVAL 10 - -#define REGISTER_NOT_SPECIFIED -1 - -struct i2c_device_info { - byte addr; - byte reg; - byte bytes; -}; - -i2c_device_info query[MAX_QUERIES]; - -byte i2cRxData[32]; -boolean readingContinuously = false; -byte queryIndex = 0; - -void readAndReportData(byte address, int theRegister, byte numBytes) -{ - if (theRegister != REGISTER_NOT_SPECIFIED) { - Wire.beginTransmission(address); - Wire.send((byte)theRegister); - Wire.endTransmission(); - delayMicroseconds(i2cReadDelayTime); // delay is necessary for some devices such as WiiNunchuck - } - else { - theRegister = 0; // fill the register with a dummy value - } - - Wire.requestFrom(address, numBytes); - - // check to be sure correct number of bytes were returned by slave - if(numBytes == Wire.available()) { - i2cRxData[0] = address; - i2cRxData[1] = theRegister; - for (int i = 0; i < numBytes; i++) { - i2cRxData[2 + i] = Wire.receive(); - } - // send slave address, register and received bytes - Firmata.sendSysex(I2C_REPLY, numBytes + 2, i2cRxData); - } - else { - if(numBytes > Wire.available()) { - Firmata.sendString("I2C Read Error: Too many bytes received"); - } else { - Firmata.sendString("I2C Read Error: Too few bytes received"); - } - } - -} - -void sysexCallback(byte command, byte argc, byte *argv) -{ - byte mode; - byte slaveAddress; - byte slaveRegister; - byte data; - int delayTime; - - if (command == I2C_REQUEST) { - mode = argv[1] & I2C_READ_WRITE_MODE_MASK; - slaveAddress = argv[0]; - - switch(mode) { - case I2C_WRITE: - Wire.beginTransmission(slaveAddress); - for (byte i = 2; i < argc; i += 2) { - data = argv[i] + (argv[i + 1] << 7); - Wire.send(data); - } - Wire.endTransmission(); - delayMicroseconds(70); // TODO is this needed? - break; - case I2C_READ: - if (argc == 6) { - // a slave register is specified - slaveRegister = argv[2] + (argv[3] << 7); - data = argv[4] + (argv[5] << 7); // bytes to read - readAndReportData(slaveAddress, (int)slaveRegister, data); - } - else { - // a slave register is NOT specified - data = argv[2] + (argv[3] << 7); // bytes to read - readAndReportData(slaveAddress, (int)REGISTER_NOT_SPECIFIED, data); - } - break; - case I2C_READ_CONTINUOUSLY: - if ((queryIndex + 1) >= MAX_QUERIES) { - // too many queries, just ignore - Firmata.sendString("too many queries"); - break; - } - query[queryIndex].addr = slaveAddress; - query[queryIndex].reg = argv[2] + (argv[3] << 7); - query[queryIndex].bytes = argv[4] + (argv[5] << 7); - readingContinuously = true; - queryIndex++; - break; - case I2C_STOP_READING: - readingContinuously = false; - queryIndex = 0; - break; - default: - break; - } - } - else if (command == SAMPLING_INTERVAL) { - samplingInterval = argv[0] + (argv[1] << 7); - - if (samplingInterval < MINIMUM_SAMPLING_INTERVAL) { - samplingInterval = MINIMUM_SAMPLING_INTERVAL; - } - - samplingInterval -= 1; - Firmata.sendString("sampling interval"); - } - - else if (command == I2C_CONFIG) { - delayTime = (argv[4] + (argv[5] << 7)); // MSB - delayTime = (delayTime << 8) + (argv[2] + (argv[3] << 7)); // add LSB - - if((argv[0] + (argv[1] << 7)) > 0) { - enablePowerPins(PORTC3, PORTC2); - } - - if(delayTime > 0) { - i2cReadDelayTime = delayTime; - } - - if(argc > 6) { - // If you extend I2C_Config, handle your data here - } - - } -} - -void systemResetCallback() -{ - readingContinuously = false; - queryIndex = 0; -} - -/* reference: BlinkM_funcs.h by Tod E. Kurt, ThingM, http://thingm.com/ */ -// Enables Pins A2 and A3 to be used as GND and Power -// so that I2C devices can be plugged directly -// into Arduino header (pins A2 - A5) -static void enablePowerPins(byte pwrpin, byte gndpin) -{ - if(powerPinsEnabled == 0) { - DDRC |= _BV(pwrpin) | _BV(gndpin); - PORTC &=~ _BV(gndpin); - PORTC |= _BV(pwrpin); - powerPinsEnabled = 1; - Firmata.sendString("Power pins enabled"); - delay(100); - } -} - -void setup() -{ - Firmata.setFirmwareVersion(2, 0); - - Firmata.attach(START_SYSEX, sysexCallback); - Firmata.attach(SYSTEM_RESET, systemResetCallback); - - for (int i = 0; i < TOTAL_DIGITAL_PINS; ++i) { - pinMode(i, OUTPUT); - } - - Firmata.begin(57600); - Wire.begin(); -} - -void loop() -{ - while (Firmata.available()) { - Firmata.processInput(); - } - - currentMillis = millis(); - if (currentMillis > nextExecuteMillis) { - nextExecuteMillis = currentMillis + samplingInterval; - - for (byte i = 0; i < queryIndex; i++) { - readAndReportData(query[i].addr, query[i].reg, query[i].bytes); - } - } -} diff --git a/libraries/Firmata/examples/ServoFirmata/Makefile b/libraries/Firmata/examples/ServoFirmata/Makefile deleted file mode 100644 index e968c0a..0000000 --- a/libraries/Firmata/examples/ServoFirmata/Makefile +++ /dev/null @@ -1,263 +0,0 @@ -# Arduino makefile -# -# This makefile allows you to build sketches from the command line -# without the Arduino environment (or Java). -# -# The Arduino environment does preliminary processing on a sketch before -# compiling it. If you're using this makefile instead, you'll need to do -# a few things differently: -# -# - Give your program's file a .cpp extension (e.g. foo.cpp). -# -# - Put this line at top of your code: #include <WProgram.h> -# -# - Write prototypes for all your functions (or define them before you -# call them). A prototype declares the types of parameters a -# function will take and what type of value it will return. This -# means that you can have a call to a function before the definition -# of the function. A function prototype looks like the first line of -# the function, with a semi-colon at the end. For example: -# int digitalRead(int pin); -# -# Instructions for using the makefile: -# -# 1. Copy this file into the folder with your sketch. -# -# 2. Below, modify the line containing "TARGET" to refer to the name of -# of your program's file without an extension (e.g. TARGET = foo). -# -# 3. Modify the line containg "ARDUINO" to point the directory that -# contains the Arduino core (for normal Arduino installations, this -# is the hardware/cores/arduino sub-directory). -# -# 4. Modify the line containing "PORT" to refer to the filename -# representing the USB or serial connection to your Arduino board -# (e.g. PORT = /dev/tty.USB0). If the exact name of this file -# changes, you can use * as a wildcard (e.g. PORT = /dev/tty.USB*). -# -# 5. At the command line, change to the directory containing your -# program's file and the makefile. -# -# 6. Type "make" and press enter to compile/verify your program. -# -# 7. Type "make upload", reset your Arduino board, and press enter to -# upload your program to the Arduino board. -# -# $Id: Makefile,v 1.7 2007/04/13 05:28:23 eighthave Exp $ - -PORT = /dev/tty.usbserial-* -TARGET := $(shell pwd | sed 's|.*/\(.*\)|\1|') -ARDUINO = /Applications/arduino -ARDUINO_SRC = $(ARDUINO)/hardware/cores/arduino -ARDUINO_LIB_SRC = $(ARDUINO)/hardware/libraries -INCLUDE = -I$(ARDUINO_SRC) -I$(ARDUINO)/hardware/tools/avr/avr/include \ - -I$(ARDUINO_LIB_SRC)/EEPROM \ - -I$(ARDUINO_LIB_SRC)/Firmata \ - -I$(ARDUINO_LIB_SRC)/Servo \ - -I$(ARDUINO_LIB_SRC) -SRC = $(wildcard $(ARDUINO_SRC)/*.c) -CXXSRC = applet/$(TARGET).cpp $(ARDUINO_SRC)/HardwareSerial.cpp \ - $(ARDUINO_LIB_SRC)/EEPROM/EEPROM.cpp \ - $(ARDUINO_LIB_SRC)/Firmata/Firmata.cpp \ - $(ARDUINO_LIB_SRC)/Servo/Servo.cpp \ - $(ARDUINO_SRC)/WMath.cpp -HEADERS = $(wildcard $(ARDUINO_SRC)/*.h) $(wildcard $(ARDUINO_LIB_SRC)/*/*.h) - -MCU = atmega168 -#MCU = atmega8 -F_CPU = 16000000 -FORMAT = ihex -UPLOAD_RATE = 19200 - -# Name of this Makefile (used for "make depend"). -MAKEFILE = Makefile - -# Debugging format. -# Native formats for AVR-GCC's -g are stabs [default], or dwarf-2. -# AVR (extended) COFF requires stabs, plus an avr-objcopy run. -DEBUG = stabs - -OPT = s - -# Place -D or -U options here -CDEFS = -DF_CPU=$(F_CPU) -CXXDEFS = -DF_CPU=$(F_CPU) - -# Compiler flag to set the C Standard level. -# c89 - "ANSI" C -# gnu89 - c89 plus GCC extensions -# c99 - ISO C99 standard (not yet fully implemented) -# gnu99 - c99 plus GCC extensions -CSTANDARD = -std=gnu99 -CDEBUG = -g$(DEBUG) -CWARN = -Wall -Wstrict-prototypes -CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums -#CEXTRA = -Wa,-adhlns=$(<:.c=.lst) - -CFLAGS = $(CDEBUG) $(CDEFS) $(INCLUDE) -O$(OPT) $(CWARN) $(CSTANDARD) $(CEXTRA) -CXXFLAGS = $(CDEFS) $(INCLUDE) -O$(OPT) -#ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs -LDFLAGS = - - -# Programming support using avrdude. Settings and variables. -AVRDUDE_PROGRAMMER = stk500 -AVRDUDE_PORT = $(PORT) -AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex -AVRDUDE_FLAGS = -F -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) \ - -b $(UPLOAD_RATE) -q -V - -# Program settings -CC = avr-gcc -CXX = avr-g++ -OBJCOPY = avr-objcopy -OBJDUMP = avr-objdump -SIZE = avr-size -NM = avr-nm -AVRDUDE = avrdude -REMOVE = rm -f -MV = mv -f - -# Define all object files. -OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o) - -# Define all listing files. -LST = $(ASRC:.S=.lst) $(CXXSRC:.cpp=.lst) $(SRC:.c=.lst) - -# Combine all necessary flags and optional flags. -# Add target processor to flags. -ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) -ALL_CXXFLAGS = -mmcu=$(MCU) -I. $(CXXFLAGS) -ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS) - - -# Default target. -all: build - -build: applet/$(TARGET).hex - -eep: applet/$(TARGET).eep -lss: applet/$(TARGET).lss -sym: applet/$(TARGET).sym - - -# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB. -COFFCONVERT=$(OBJCOPY) --debugging \ ---change-section-address .data-0x800000 \ ---change-section-address .bss-0x800000 \ ---change-section-address .noinit-0x800000 \ ---change-section-address .eeprom-0x810000 - - -coff: applet/$(TARGET).elf - $(COFFCONVERT) -O coff-avr applet/$(TARGET).elf applet/$(TARGET).cof - - -extcoff: applet/$(TARGET).elf - $(COFFCONVERT) -O coff-ext-avr applet/$(TARGET).elf applet/$(TARGET).cof - - -.SUFFIXES: .elf .hex .eep .lss .sym .pde - -.elf.hex: - $(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@ - -.elf.eep: - -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \ - --change-section-lma .eeprom=0 -O $(FORMAT) $< $@ - -# Create extended listing file from ELF output file. -.elf.lss: - $(OBJDUMP) -h -S $< > $@ - -# Create a symbol table from ELF output file. -.elf.sym: - $(NM) -n $< > $@ - - -# Compile: create object files from C++ source files. -.cpp.o: $(HEADERS) - $(CXX) -c $(ALL_CXXFLAGS) $< -o $@ - -# Compile: create object files from C source files. -.c.o: $(HEADERS) - $(CC) -c $(ALL_CFLAGS) $< -o $@ - - -# Compile: create assembler files from C source files. -.c.s: - $(CC) -S $(ALL_CFLAGS) $< -o $@ - - -# Assemble: create object files from assembler source files. -.S.o: - $(CC) -c $(ALL_ASFLAGS) $< -o $@ - - - -applet/$(TARGET).cpp: $(TARGET).pde - test -d applet || mkdir applet - echo '#include "WProgram.h"' > applet/$(TARGET).cpp - echo '#include "avr/interrupt.h"' >> applet/$(TARGET).cpp - sed -n 's|^\(void .*)\).*|\1;|p' $(TARGET).pde | grep -v 'setup()' | \ - grep -v 'loop()' >> applet/$(TARGET).cpp - cat $(TARGET).pde >> applet/$(TARGET).cpp - cat $(ARDUINO_SRC)/main.cxx >> applet/$(TARGET).cpp - -# Link: create ELF output file from object files. -applet/$(TARGET).elf: applet/$(TARGET).cpp $(OBJ) - $(CC) $(ALL_CFLAGS) $(OBJ) --output $@ $(LDFLAGS) - -pd_close_serial: - echo 'close;' | /Applications/Pd-extended.app/Contents/Resources/bin/pdsend 34567 || true - -# Program the device. -upload: applet/$(TARGET).hex - $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) - - -pd_test: build pd_close_serial upload - -# Target: clean project. -clean: - $(REMOVE) -- applet/$(TARGET).hex applet/$(TARGET).eep \ - applet/$(TARGET).cof applet/$(TARGET).elf $(TARGET).map \ - applet/$(TARGET).sym applet/$(TARGET).lss applet/$(TARGET).cpp \ - $(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d) - rmdir -- applet - -depend: - if grep '^# DO NOT DELETE' $(MAKEFILE) >/dev/null; \ - then \ - sed -e '/^# DO NOT DELETE/,$$d' $(MAKEFILE) > \ - $(MAKEFILE).$$$$ && \ - $(MV) $(MAKEFILE).$$$$ $(MAKEFILE); \ - fi - echo '# DO NOT DELETE THIS LINE -- make depend depends on it.' \ - >> $(MAKEFILE); \ - $(CC) -M -mmcu=$(MCU) $(CDEFS) $(INCLUDE) $(SRC) $(ASRC) >> $(MAKEFILE) - -.PHONY: all build eep lss sym coff extcoff clean depend pd_close_serial pd_test - -# for emacs -etags: - make etags_`uname -s` - etags *.pde \ - $(ARDUINO_SRC)/*.[ch] \ - $(ARDUINO_SRC)/*.cpp \ - $(ARDUINO_LIB_SRC)/*/*.[ch] \ - $(ARDUINO_LIB_SRC)/*/*.cpp \ - $(ARDUINO)/hardware/tools/avr/avr/include/avr/*.[ch] \ - $(ARDUINO)/hardware/tools/avr/avr/include/*.[ch] - -etags_Darwin: -# etags -a - -etags_Linux: -# etags -a /usr/include/*.h linux/input.h /usr/include/sys/*.h - -etags_MINGW: -# etags -a /usr/include/*.h /usr/include/sys/*.h - - - diff --git a/libraries/Firmata/examples/ServoFirmata/ServoFirmata.pde b/libraries/Firmata/examples/ServoFirmata/ServoFirmata.pde deleted file mode 100644 index fa48e2b..0000000 --- a/libraries/Firmata/examples/ServoFirmata/ServoFirmata.pde +++ /dev/null @@ -1,39 +0,0 @@ -/* This firmware supports as many servos as possible using the Servo" library - * included in Arduino 0012 - * - * TODO add message to configure minPulse/maxPulse/degrees - * - * This example code is in the public domain. - */ - -#include <Firmata.h> -#include <Servo.h> - -Servo servo9; -Servo servo10; - -void analogWriteCallback(byte pin, int value) -{ - if(pin == 9) - servo9.write(value); - if(pin == 10) - servo10.write(value); -} - -void setup() -{ - Firmata.setFirmwareVersion(0, 2); - Firmata.attach(ANALOG_MESSAGE, analogWriteCallback); - - servo9.attach(9); - servo10.attach(10); - - Firmata.begin(57600); -} - -void loop() -{ - while(Firmata.available()) - Firmata.processInput(); -} - diff --git a/libraries/Firmata/examples/SimpleAnalogFirmata/Makefile b/libraries/Firmata/examples/SimpleAnalogFirmata/Makefile deleted file mode 100644 index e968c0a..0000000 --- a/libraries/Firmata/examples/SimpleAnalogFirmata/Makefile +++ /dev/null @@ -1,263 +0,0 @@ -# Arduino makefile -# -# This makefile allows you to build sketches from the command line -# without the Arduino environment (or Java). -# -# The Arduino environment does preliminary processing on a sketch before -# compiling it. If you're using this makefile instead, you'll need to do -# a few things differently: -# -# - Give your program's file a .cpp extension (e.g. foo.cpp). -# -# - Put this line at top of your code: #include <WProgram.h> -# -# - Write prototypes for all your functions (or define them before you -# call them). A prototype declares the types of parameters a -# function will take and what type of value it will return. This -# means that you can have a call to a function before the definition -# of the function. A function prototype looks like the first line of -# the function, with a semi-colon at the end. For example: -# int digitalRead(int pin); -# -# Instructions for using the makefile: -# -# 1. Copy this file into the folder with your sketch. -# -# 2. Below, modify the line containing "TARGET" to refer to the name of -# of your program's file without an extension (e.g. TARGET = foo). -# -# 3. Modify the line containg "ARDUINO" to point the directory that -# contains the Arduino core (for normal Arduino installations, this -# is the hardware/cores/arduino sub-directory). -# -# 4. Modify the line containing "PORT" to refer to the filename -# representing the USB or serial connection to your Arduino board -# (e.g. PORT = /dev/tty.USB0). If the exact name of this file -# changes, you can use * as a wildcard (e.g. PORT = /dev/tty.USB*). -# -# 5. At the command line, change to the directory containing your -# program's file and the makefile. -# -# 6. Type "make" and press enter to compile/verify your program. -# -# 7. Type "make upload", reset your Arduino board, and press enter to -# upload your program to the Arduino board. -# -# $Id: Makefile,v 1.7 2007/04/13 05:28:23 eighthave Exp $ - -PORT = /dev/tty.usbserial-* -TARGET := $(shell pwd | sed 's|.*/\(.*\)|\1|') -ARDUINO = /Applications/arduino -ARDUINO_SRC = $(ARDUINO)/hardware/cores/arduino -ARDUINO_LIB_SRC = $(ARDUINO)/hardware/libraries -INCLUDE = -I$(ARDUINO_SRC) -I$(ARDUINO)/hardware/tools/avr/avr/include \ - -I$(ARDUINO_LIB_SRC)/EEPROM \ - -I$(ARDUINO_LIB_SRC)/Firmata \ - -I$(ARDUINO_LIB_SRC)/Servo \ - -I$(ARDUINO_LIB_SRC) -SRC = $(wildcard $(ARDUINO_SRC)/*.c) -CXXSRC = applet/$(TARGET).cpp $(ARDUINO_SRC)/HardwareSerial.cpp \ - $(ARDUINO_LIB_SRC)/EEPROM/EEPROM.cpp \ - $(ARDUINO_LIB_SRC)/Firmata/Firmata.cpp \ - $(ARDUINO_LIB_SRC)/Servo/Servo.cpp \ - $(ARDUINO_SRC)/WMath.cpp -HEADERS = $(wildcard $(ARDUINO_SRC)/*.h) $(wildcard $(ARDUINO_LIB_SRC)/*/*.h) - -MCU = atmega168 -#MCU = atmega8 -F_CPU = 16000000 -FORMAT = ihex -UPLOAD_RATE = 19200 - -# Name of this Makefile (used for "make depend"). -MAKEFILE = Makefile - -# Debugging format. -# Native formats for AVR-GCC's -g are stabs [default], or dwarf-2. -# AVR (extended) COFF requires stabs, plus an avr-objcopy run. -DEBUG = stabs - -OPT = s - -# Place -D or -U options here -CDEFS = -DF_CPU=$(F_CPU) -CXXDEFS = -DF_CPU=$(F_CPU) - -# Compiler flag to set the C Standard level. -# c89 - "ANSI" C -# gnu89 - c89 plus GCC extensions -# c99 - ISO C99 standard (not yet fully implemented) -# gnu99 - c99 plus GCC extensions -CSTANDARD = -std=gnu99 -CDEBUG = -g$(DEBUG) -CWARN = -Wall -Wstrict-prototypes -CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums -#CEXTRA = -Wa,-adhlns=$(<:.c=.lst) - -CFLAGS = $(CDEBUG) $(CDEFS) $(INCLUDE) -O$(OPT) $(CWARN) $(CSTANDARD) $(CEXTRA) -CXXFLAGS = $(CDEFS) $(INCLUDE) -O$(OPT) -#ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs -LDFLAGS = - - -# Programming support using avrdude. Settings and variables. -AVRDUDE_PROGRAMMER = stk500 -AVRDUDE_PORT = $(PORT) -AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex -AVRDUDE_FLAGS = -F -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) \ - -b $(UPLOAD_RATE) -q -V - -# Program settings -CC = avr-gcc -CXX = avr-g++ -OBJCOPY = avr-objcopy -OBJDUMP = avr-objdump -SIZE = avr-size -NM = avr-nm -AVRDUDE = avrdude -REMOVE = rm -f -MV = mv -f - -# Define all object files. -OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o) - -# Define all listing files. -LST = $(ASRC:.S=.lst) $(CXXSRC:.cpp=.lst) $(SRC:.c=.lst) - -# Combine all necessary flags and optional flags. -# Add target processor to flags. -ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) -ALL_CXXFLAGS = -mmcu=$(MCU) -I. $(CXXFLAGS) -ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS) - - -# Default target. -all: build - -build: applet/$(TARGET).hex - -eep: applet/$(TARGET).eep -lss: applet/$(TARGET).lss -sym: applet/$(TARGET).sym - - -# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB. -COFFCONVERT=$(OBJCOPY) --debugging \ ---change-section-address .data-0x800000 \ ---change-section-address .bss-0x800000 \ ---change-section-address .noinit-0x800000 \ ---change-section-address .eeprom-0x810000 - - -coff: applet/$(TARGET).elf - $(COFFCONVERT) -O coff-avr applet/$(TARGET).elf applet/$(TARGET).cof - - -extcoff: applet/$(TARGET).elf - $(COFFCONVERT) -O coff-ext-avr applet/$(TARGET).elf applet/$(TARGET).cof - - -.SUFFIXES: .elf .hex .eep .lss .sym .pde - -.elf.hex: - $(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@ - -.elf.eep: - -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \ - --change-section-lma .eeprom=0 -O $(FORMAT) $< $@ - -# Create extended listing file from ELF output file. -.elf.lss: - $(OBJDUMP) -h -S $< > $@ - -# Create a symbol table from ELF output file. -.elf.sym: - $(NM) -n $< > $@ - - -# Compile: create object files from C++ source files. -.cpp.o: $(HEADERS) - $(CXX) -c $(ALL_CXXFLAGS) $< -o $@ - -# Compile: create object files from C source files. -.c.o: $(HEADERS) - $(CC) -c $(ALL_CFLAGS) $< -o $@ - - -# Compile: create assembler files from C source files. -.c.s: - $(CC) -S $(ALL_CFLAGS) $< -o $@ - - -# Assemble: create object files from assembler source files. -.S.o: - $(CC) -c $(ALL_ASFLAGS) $< -o $@ - - - -applet/$(TARGET).cpp: $(TARGET).pde - test -d applet || mkdir applet - echo '#include "WProgram.h"' > applet/$(TARGET).cpp - echo '#include "avr/interrupt.h"' >> applet/$(TARGET).cpp - sed -n 's|^\(void .*)\).*|\1;|p' $(TARGET).pde | grep -v 'setup()' | \ - grep -v 'loop()' >> applet/$(TARGET).cpp - cat $(TARGET).pde >> applet/$(TARGET).cpp - cat $(ARDUINO_SRC)/main.cxx >> applet/$(TARGET).cpp - -# Link: create ELF output file from object files. -applet/$(TARGET).elf: applet/$(TARGET).cpp $(OBJ) - $(CC) $(ALL_CFLAGS) $(OBJ) --output $@ $(LDFLAGS) - -pd_close_serial: - echo 'close;' | /Applications/Pd-extended.app/Contents/Resources/bin/pdsend 34567 || true - -# Program the device. -upload: applet/$(TARGET).hex - $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) - - -pd_test: build pd_close_serial upload - -# Target: clean project. -clean: - $(REMOVE) -- applet/$(TARGET).hex applet/$(TARGET).eep \ - applet/$(TARGET).cof applet/$(TARGET).elf $(TARGET).map \ - applet/$(TARGET).sym applet/$(TARGET).lss applet/$(TARGET).cpp \ - $(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d) - rmdir -- applet - -depend: - if grep '^# DO NOT DELETE' $(MAKEFILE) >/dev/null; \ - then \ - sed -e '/^# DO NOT DELETE/,$$d' $(MAKEFILE) > \ - $(MAKEFILE).$$$$ && \ - $(MV) $(MAKEFILE).$$$$ $(MAKEFILE); \ - fi - echo '# DO NOT DELETE THIS LINE -- make depend depends on it.' \ - >> $(MAKEFILE); \ - $(CC) -M -mmcu=$(MCU) $(CDEFS) $(INCLUDE) $(SRC) $(ASRC) >> $(MAKEFILE) - -.PHONY: all build eep lss sym coff extcoff clean depend pd_close_serial pd_test - -# for emacs -etags: - make etags_`uname -s` - etags *.pde \ - $(ARDUINO_SRC)/*.[ch] \ - $(ARDUINO_SRC)/*.cpp \ - $(ARDUINO_LIB_SRC)/*/*.[ch] \ - $(ARDUINO_LIB_SRC)/*/*.cpp \ - $(ARDUINO)/hardware/tools/avr/avr/include/avr/*.[ch] \ - $(ARDUINO)/hardware/tools/avr/avr/include/*.[ch] - -etags_Darwin: -# etags -a - -etags_Linux: -# etags -a /usr/include/*.h linux/input.h /usr/include/sys/*.h - -etags_MINGW: -# etags -a /usr/include/*.h /usr/include/sys/*.h - - - diff --git a/libraries/Firmata/examples/SimpleAnalogFirmata/SimpleAnalogFirmata.pde b/libraries/Firmata/examples/SimpleAnalogFirmata/SimpleAnalogFirmata.pde deleted file mode 100644 index 430d0d0..0000000 --- a/libraries/Firmata/examples/SimpleAnalogFirmata/SimpleAnalogFirmata.pde +++ /dev/null @@ -1,32 +0,0 @@ -/* Supports as many analog inputs and analog PWM outputs as possible. - * - * This example code is in the public domain. - */ -#include <Firmata.h> - -byte analogPin; - -void analogWriteCallback(byte pin, int value) -{ - pinMode(pin,OUTPUT); - analogWrite(pin, value); -} - -void setup() -{ - Firmata.setFirmwareVersion(0, 1); - Firmata.attach(ANALOG_MESSAGE, analogWriteCallback); - Firmata.begin(57600); -} - -void loop() -{ - while(Firmata.available()) { - Firmata.processInput(); - } - for(analogPin = 0; analogPin < TOTAL_ANALOG_PINS; analogPin++) { - Firmata.sendAnalog(analogPin, analogRead(analogPin)); - } -} - - diff --git a/libraries/Firmata/examples/SimpleDigitalFirmata/Makefile b/libraries/Firmata/examples/SimpleDigitalFirmata/Makefile deleted file mode 100644 index e968c0a..0000000 --- a/libraries/Firmata/examples/SimpleDigitalFirmata/Makefile +++ /dev/null @@ -1,263 +0,0 @@ -# Arduino makefile -# -# This makefile allows you to build sketches from the command line -# without the Arduino environment (or Java). -# -# The Arduino environment does preliminary processing on a sketch before -# compiling it. If you're using this makefile instead, you'll need to do -# a few things differently: -# -# - Give your program's file a .cpp extension (e.g. foo.cpp). -# -# - Put this line at top of your code: #include <WProgram.h> -# -# - Write prototypes for all your functions (or define them before you -# call them). A prototype declares the types of parameters a -# function will take and what type of value it will return. This -# means that you can have a call to a function before the definition -# of the function. A function prototype looks like the first line of -# the function, with a semi-colon at the end. For example: -# int digitalRead(int pin); -# -# Instructions for using the makefile: -# -# 1. Copy this file into the folder with your sketch. -# -# 2. Below, modify the line containing "TARGET" to refer to the name of -# of your program's file without an extension (e.g. TARGET = foo). -# -# 3. Modify the line containg "ARDUINO" to point the directory that -# contains the Arduino core (for normal Arduino installations, this -# is the hardware/cores/arduino sub-directory). -# -# 4. Modify the line containing "PORT" to refer to the filename -# representing the USB or serial connection to your Arduino board -# (e.g. PORT = /dev/tty.USB0). If the exact name of this file -# changes, you can use * as a wildcard (e.g. PORT = /dev/tty.USB*). -# -# 5. At the command line, change to the directory containing your -# program's file and the makefile. -# -# 6. Type "make" and press enter to compile/verify your program. -# -# 7. Type "make upload", reset your Arduino board, and press enter to -# upload your program to the Arduino board. -# -# $Id: Makefile,v 1.7 2007/04/13 05:28:23 eighthave Exp $ - -PORT = /dev/tty.usbserial-* -TARGET := $(shell pwd | sed 's|.*/\(.*\)|\1|') -ARDUINO = /Applications/arduino -ARDUINO_SRC = $(ARDUINO)/hardware/cores/arduino -ARDUINO_LIB_SRC = $(ARDUINO)/hardware/libraries -INCLUDE = -I$(ARDUINO_SRC) -I$(ARDUINO)/hardware/tools/avr/avr/include \ - -I$(ARDUINO_LIB_SRC)/EEPROM \ - -I$(ARDUINO_LIB_SRC)/Firmata \ - -I$(ARDUINO_LIB_SRC)/Servo \ - -I$(ARDUINO_LIB_SRC) -SRC = $(wildcard $(ARDUINO_SRC)/*.c) -CXXSRC = applet/$(TARGET).cpp $(ARDUINO_SRC)/HardwareSerial.cpp \ - $(ARDUINO_LIB_SRC)/EEPROM/EEPROM.cpp \ - $(ARDUINO_LIB_SRC)/Firmata/Firmata.cpp \ - $(ARDUINO_LIB_SRC)/Servo/Servo.cpp \ - $(ARDUINO_SRC)/WMath.cpp -HEADERS = $(wildcard $(ARDUINO_SRC)/*.h) $(wildcard $(ARDUINO_LIB_SRC)/*/*.h) - -MCU = atmega168 -#MCU = atmega8 -F_CPU = 16000000 -FORMAT = ihex -UPLOAD_RATE = 19200 - -# Name of this Makefile (used for "make depend"). -MAKEFILE = Makefile - -# Debugging format. -# Native formats for AVR-GCC's -g are stabs [default], or dwarf-2. -# AVR (extended) COFF requires stabs, plus an avr-objcopy run. -DEBUG = stabs - -OPT = s - -# Place -D or -U options here -CDEFS = -DF_CPU=$(F_CPU) -CXXDEFS = -DF_CPU=$(F_CPU) - -# Compiler flag to set the C Standard level. -# c89 - "ANSI" C -# gnu89 - c89 plus GCC extensions -# c99 - ISO C99 standard (not yet fully implemented) -# gnu99 - c99 plus GCC extensions -CSTANDARD = -std=gnu99 -CDEBUG = -g$(DEBUG) -CWARN = -Wall -Wstrict-prototypes -CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums -#CEXTRA = -Wa,-adhlns=$(<:.c=.lst) - -CFLAGS = $(CDEBUG) $(CDEFS) $(INCLUDE) -O$(OPT) $(CWARN) $(CSTANDARD) $(CEXTRA) -CXXFLAGS = $(CDEFS) $(INCLUDE) -O$(OPT) -#ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs -LDFLAGS = - - -# Programming support using avrdude. Settings and variables. -AVRDUDE_PROGRAMMER = stk500 -AVRDUDE_PORT = $(PORT) -AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex -AVRDUDE_FLAGS = -F -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) \ - -b $(UPLOAD_RATE) -q -V - -# Program settings -CC = avr-gcc -CXX = avr-g++ -OBJCOPY = avr-objcopy -OBJDUMP = avr-objdump -SIZE = avr-size -NM = avr-nm -AVRDUDE = avrdude -REMOVE = rm -f -MV = mv -f - -# Define all object files. -OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o) - -# Define all listing files. -LST = $(ASRC:.S=.lst) $(CXXSRC:.cpp=.lst) $(SRC:.c=.lst) - -# Combine all necessary flags and optional flags. -# Add target processor to flags. -ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) -ALL_CXXFLAGS = -mmcu=$(MCU) -I. $(CXXFLAGS) -ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS) - - -# Default target. -all: build - -build: applet/$(TARGET).hex - -eep: applet/$(TARGET).eep -lss: applet/$(TARGET).lss -sym: applet/$(TARGET).sym - - -# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB. -COFFCONVERT=$(OBJCOPY) --debugging \ ---change-section-address .data-0x800000 \ ---change-section-address .bss-0x800000 \ ---change-section-address .noinit-0x800000 \ ---change-section-address .eeprom-0x810000 - - -coff: applet/$(TARGET).elf - $(COFFCONVERT) -O coff-avr applet/$(TARGET).elf applet/$(TARGET).cof - - -extcoff: applet/$(TARGET).elf - $(COFFCONVERT) -O coff-ext-avr applet/$(TARGET).elf applet/$(TARGET).cof - - -.SUFFIXES: .elf .hex .eep .lss .sym .pde - -.elf.hex: - $(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@ - -.elf.eep: - -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \ - --change-section-lma .eeprom=0 -O $(FORMAT) $< $@ - -# Create extended listing file from ELF output file. -.elf.lss: - $(OBJDUMP) -h -S $< > $@ - -# Create a symbol table from ELF output file. -.elf.sym: - $(NM) -n $< > $@ - - -# Compile: create object files from C++ source files. -.cpp.o: $(HEADERS) - $(CXX) -c $(ALL_CXXFLAGS) $< -o $@ - -# Compile: create object files from C source files. -.c.o: $(HEADERS) - $(CC) -c $(ALL_CFLAGS) $< -o $@ - - -# Compile: create assembler files from C source files. -.c.s: - $(CC) -S $(ALL_CFLAGS) $< -o $@ - - -# Assemble: create object files from assembler source files. -.S.o: - $(CC) -c $(ALL_ASFLAGS) $< -o $@ - - - -applet/$(TARGET).cpp: $(TARGET).pde - test -d applet || mkdir applet - echo '#include "WProgram.h"' > applet/$(TARGET).cpp - echo '#include "avr/interrupt.h"' >> applet/$(TARGET).cpp - sed -n 's|^\(void .*)\).*|\1;|p' $(TARGET).pde | grep -v 'setup()' | \ - grep -v 'loop()' >> applet/$(TARGET).cpp - cat $(TARGET).pde >> applet/$(TARGET).cpp - cat $(ARDUINO_SRC)/main.cxx >> applet/$(TARGET).cpp - -# Link: create ELF output file from object files. -applet/$(TARGET).elf: applet/$(TARGET).cpp $(OBJ) - $(CC) $(ALL_CFLAGS) $(OBJ) --output $@ $(LDFLAGS) - -pd_close_serial: - echo 'close;' | /Applications/Pd-extended.app/Contents/Resources/bin/pdsend 34567 || true - -# Program the device. -upload: applet/$(TARGET).hex - $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) - - -pd_test: build pd_close_serial upload - -# Target: clean project. -clean: - $(REMOVE) -- applet/$(TARGET).hex applet/$(TARGET).eep \ - applet/$(TARGET).cof applet/$(TARGET).elf $(TARGET).map \ - applet/$(TARGET).sym applet/$(TARGET).lss applet/$(TARGET).cpp \ - $(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d) - rmdir -- applet - -depend: - if grep '^# DO NOT DELETE' $(MAKEFILE) >/dev/null; \ - then \ - sed -e '/^# DO NOT DELETE/,$$d' $(MAKEFILE) > \ - $(MAKEFILE).$$$$ && \ - $(MV) $(MAKEFILE).$$$$ $(MAKEFILE); \ - fi - echo '# DO NOT DELETE THIS LINE -- make depend depends on it.' \ - >> $(MAKEFILE); \ - $(CC) -M -mmcu=$(MCU) $(CDEFS) $(INCLUDE) $(SRC) $(ASRC) >> $(MAKEFILE) - -.PHONY: all build eep lss sym coff extcoff clean depend pd_close_serial pd_test - -# for emacs -etags: - make etags_`uname -s` - etags *.pde \ - $(ARDUINO_SRC)/*.[ch] \ - $(ARDUINO_SRC)/*.cpp \ - $(ARDUINO_LIB_SRC)/*/*.[ch] \ - $(ARDUINO_LIB_SRC)/*/*.cpp \ - $(ARDUINO)/hardware/tools/avr/avr/include/avr/*.[ch] \ - $(ARDUINO)/hardware/tools/avr/avr/include/*.[ch] - -etags_Darwin: -# etags -a - -etags_Linux: -# etags -a /usr/include/*.h linux/input.h /usr/include/sys/*.h - -etags_MINGW: -# etags -a /usr/include/*.h /usr/include/sys/*.h - - - diff --git a/libraries/Firmata/examples/SimpleDigitalFirmata/SimpleDigitalFirmata.pde b/libraries/Firmata/examples/SimpleDigitalFirmata/SimpleDigitalFirmata.pde deleted file mode 100644 index 9c4e05d..0000000 --- a/libraries/Firmata/examples/SimpleDigitalFirmata/SimpleDigitalFirmata.pde +++ /dev/null @@ -1,58 +0,0 @@ -/* Supports as many digital inputs and outputs as possible. - * - * This example code is in the public domain. - */ -#include <Firmata.h> - -byte previousPIN[2]; // PIN means PORT for input -byte previousPORT[2]; - -void outputPort(byte portNumber, byte portValue) -{ -// only send the data when it changes, otherwise you get too many messages! - if(previousPIN[portNumber] != portValue) { - Firmata.sendDigitalPort(portNumber, portValue); - previousPIN[portNumber] = portValue; - Firmata.sendDigitalPort(portNumber, portValue); - } -} - -void setPinModeCallback(byte pin, int mode) { - if(pin > 1) { // don't touch RxTx pins (0,1) - pinMode(pin, mode); - } -} - -void digitalWriteCallback(byte port, int value) -{ - byte i; - byte currentPinValue, previousPinValue; - - if(value != previousPORT[port]) { - for(i=0; i<8; i++) { - currentPinValue = (byte) value & (1 << i); - previousPinValue = previousPORT[port] & (1 << i); - if(currentPinValue != previousPinValue) { - digitalWrite(i + (port*8), currentPinValue); - } - } - previousPORT[port] = value; - } -} - -void setup() -{ - Firmata.setFirmwareVersion(0, 1); - Firmata.attach(DIGITAL_MESSAGE, digitalWriteCallback); - Firmata.attach(SET_PIN_MODE, setPinModeCallback); - Firmata.begin(57600); -} - -void loop() -{ - outputPort(0, PIND &~ B00000011); // pins 0-7, ignoring Rx/Tx pins (0/1) - outputPort(1, PINB); // pins 8-13 - while(Firmata.available()) { - Firmata.processInput(); - } -} diff --git a/libraries/Firmata/examples/StandardFirmata/LICENSE.txt b/libraries/Firmata/examples/StandardFirmata/LICENSE.txt deleted file mode 100644 index 77cec6d..0000000 --- a/libraries/Firmata/examples/StandardFirmata/LICENSE.txt +++ /dev/null @@ -1,458 +0,0 @@ - - GNU LESSER GENERAL PUBLIC LICENSE - Version 2.1, February 1999 - - Copyright (C) 1991, 1999 Free Software Foundation, Inc. - 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA - Everyone is permitted to copy and distribute verbatim copies - of this license document, but changing it is not allowed. - -[This is the first released version of the Lesser GPL. It also counts - as the successor of the GNU Library Public License, version 2, hence - the version number 2.1.] - - Preamble - - The licenses for most software are designed to take away your -freedom to share and change it. By contrast, the GNU General Public -Licenses are intended to guarantee your freedom to share and change -free software--to make sure the software is free for all its users. - - This license, the Lesser General Public License, applies to some -specially designated software packages--typically libraries--of the -Free Software Foundation and other authors who decide to use it. You -can use it too, but we suggest you first think carefully about whether -this license or the ordinary General Public License is the better -strategy to use in any particular case, based on the explanations below. - - When we speak of free software, we are referring to freedom of use, -not price. Our General Public Licenses are designed to make sure that -you have the freedom to distribute copies of free software (and charge -for this service if you wish); that you receive source code or can get -it if you want it; that you can change the software and use pieces of -it in new free programs; and that you are informed that you can do -these things. - - To protect your rights, we need to make restrictions that forbid -distributors to deny you these rights or to ask you to surrender these -rights. These restrictions translate to certain responsibilities for -you if you distribute copies of the library or if you modify it. - - For example, if you distribute copies of the library, whether gratis -or for a fee, you must give the recipients all the rights that we gave -you. You must make sure that they, too, receive or can get the source -code. If you link other code with the library, you must provide -complete object files to the recipients, so that they can relink them -with the library after making changes to the library and recompiling -it. And you must show them these terms so they know their rights. - - We protect your rights with a two-step method: (1) we copyright the -library, and (2) we offer you this license, which gives you legal -permission to copy, distribute and/or modify the library. - - To protect each distributor, we want to make it very clear that -there is no warranty for the free library. Also, if the library is -modified by someone else and passed on, the recipients should know -that what they have is not the original version, so that the original -author's reputation will not be affected by problems that might be -introduced by others. - - Finally, software patents pose a constant threat to the existence of -any free program. We wish to make sure that a company cannot -effectively restrict the users of a free program by obtaining a -restrictive license from a patent holder. Therefore, we insist that -any patent license obtained for a version of the library must be -consistent with the full freedom of use specified in this license. - - Most GNU software, including some libraries, is covered by the -ordinary GNU General Public License. This license, the GNU Lesser -General Public License, applies to certain designated libraries, and -is quite different from the ordinary General Public License. We use -this license for certain libraries in order to permit linking those -libraries into non-free programs. - - When a program is linked with a library, whether statically or using -a shared library, the combination of the two is legally speaking a -combined work, a derivative of the original library. The ordinary -General Public License therefore permits such linking only if the -entire combination fits its criteria of freedom. The Lesser General -Public License permits more lax criteria for linking other code with -the library. - - We call this license the "Lesser" General Public License because it -does Less to protect the user's freedom than the ordinary General -Public License. It also provides other free software developers Less -of an advantage over competing non-free programs. These disadvantages -are the reason we use the ordinary General Public License for many -libraries. However, the Lesser license provides advantages in certain -special circumstances. - - For example, on rare occasions, there may be a special need to -encourage the widest possible use of a certain library, so that it becomes -a de-facto standard. To achieve this, non-free programs must be -allowed to use the library. A more frequent case is that a free -library does the same job as widely used non-free libraries. In this -case, there is little to gain by limiting the free library to free -software only, so we use the Lesser General Public License. - - In other cases, permission to use a particular library in non-free -programs enables a greater number of people to use a large body of -free software. For example, permission to use the GNU C Library in -non-free programs enables many more people to use the whole GNU -operating system, as well as its variant, the GNU/Linux operating -system. - - Although the Lesser General Public License is Less protective of the -users' freedom, it does ensure that the user of a program that is -linked with the Library has the freedom and the wherewithal to run -that program using a modified version of the Library. - - The precise terms and conditions for copying, distribution and -modification follow. Pay close attention to the difference between a -"work based on the library" and a "work that uses the library". The -former contains code derived from the library, whereas the latter must -be combined with the library in order to run. - - GNU LESSER GENERAL PUBLIC LICENSE - TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION - - 0. This License Agreement applies to any software library or other -program which contains a notice placed by the copyright holder or -other authorized party saying it may be distributed under the terms of -this Lesser General Public License (also called "this License"). -Each licensee is addressed as "you". - - A "library" means a collection of software functions and/or data -prepared so as to be conveniently linked with application programs -(which use some of those functions and data) to form executables. - - The "Library", below, refers to any such software library or work -which has been distributed under these terms. A "work based on the -Library" means either the Library or any derivative work under -copyright law: that is to say, a work containing the Library or a -portion of it, either verbatim or with modifications and/or translated -straightforwardly into another language. (Hereinafter, translation is -included without limitation in the term "modification".) - - "Source code" for a work means the preferred form of the work for -making modifications to it. For a library, complete source code means -all the source code for all modules it contains, plus any associated -interface definition files, plus the scripts used to control compilation -and installation of the library. - - Activities other than copying, distribution and modification are not -covered by this License; they are outside its scope. The act of -running a program using the Library is not restricted, and output from -such a program is covered only if its contents constitute a work based -on the Library (independent of the use of the Library in a tool for -writing it). Whether that is true depends on what the Library does -and what the program that uses the Library does. - - 1. You may copy and distribute verbatim copies of the Library's -complete source code as you receive it, in any medium, provided that -you conspicuously and appropriately publish on each copy an -appropriate copyright notice and disclaimer of warranty; keep intact -all the notices that refer to this License and to the absence of any -warranty; and distribute a copy of this License along with the -Library. - - You may charge a fee for the physical act of transferring a copy, -and you may at your option offer warranty protection in exchange for a -fee. - - 2. You may modify your copy or copies of the Library or any portion -of it, thus forming a work based on the Library, and copy and -distribute such modifications or work under the terms of Section 1 -above, provided that you also meet all of these conditions: - - a) The modified work must itself be a software library. - - b) You must cause the files modified to carry prominent notices - stating that you changed the files and the date of any change. - - c) You must cause the whole of the work to be licensed at no - charge to all third parties under the terms of this License. - - d) If a facility in the modified Library refers to a function or a - table of data to be supplied by an application program that uses - the facility, other than as an argument passed when the facility - is invoked, then you must make a good faith effort to ensure that, - in the event an application does not supply such function or - table, the facility still operates, and performs whatever part of - its purpose remains meaningful. - - (For example, a function in a library to compute square roots has - a purpose that is entirely well-defined independent of the - application. Therefore, Subsection 2d requires that any - application-supplied function or table used by this function must - be optional: if the application does not supply it, the square - root function must still compute square roots.) - -These requirements apply to the modified work as a whole. If -identifiable sections of that work are not derived from the Library, -and can be reasonably considered independent and separate works in -themselves, then this License, and its terms, do not apply to those -sections when you distribute them as separate works. But when you -distribute the same sections as part of a whole which is a work based -on the Library, the distribution of the whole must be on the terms of -this License, whose permissions for other licensees extend to the -entire whole, and thus to each and every part regardless of who wrote -it. - -Thus, it is not the intent of this section to claim rights or contest -your rights to work written entirely by you; rather, the intent is to -exercise the right to control the distribution of derivative or -collective works based on the Library. - -In addition, mere aggregation of another work not based on the Library -with the Library (or with a work based on the Library) on a volume of -a storage or distribution medium does not bring the other work under -the scope of this License. - - 3. You may opt to apply the terms of the ordinary GNU General Public -License instead of this License to a given copy of the Library. To do -this, you must alter all the notices that refer to this License, so -that they refer to the ordinary GNU General Public License, version 2, -instead of to this License. (If a newer version than version 2 of the -ordinary GNU General Public License has appeared, then you can specify -that version instead if you wish.) Do not make any other change in -these notices. - - Once this change is made in a given copy, it is irreversible for -that copy, so the ordinary GNU General Public License applies to all -subsequent copies and derivative works made from that copy. - - This option is useful when you wish to copy part of the code of -the Library into a program that is not a library. - - 4. You may copy and distribute the Library (or a portion or -derivative of it, under Section 2) in object code or executable form -under the terms of Sections 1 and 2 above provided that you accompany -it with the complete corresponding machine-readable source code, which -must be distributed under the terms of Sections 1 and 2 above on a -medium customarily used for software interchange. - - If distribution of object code is made by offering access to copy -from a designated place, then offering equivalent access to copy the -source code from the same place satisfies the requirement to -distribute the source code, even though third parties are not -compelled to copy the source along with the object code. - - 5. A program that contains no derivative of any portion of the -Library, but is designed to work with the Library by being compiled or -linked with it, is called a "work that uses the Library". Such a -work, in isolation, is not a derivative work of the Library, and -therefore falls outside the scope of this License. - - However, linking a "work that uses the Library" with the Library -creates an executable that is a derivative of the Library (because it -contains portions of the Library), rather than a "work that uses the -library". The executable is therefore covered by this License. -Section 6 states terms for distribution of such executables. - - When a "work that uses the Library" uses material from a header file -that is part of the Library, the object code for the work may be a -derivative work of the Library even though the source code is not. -Whether this is true is especially significant if the work can be -linked without the Library, or if the work is itself a library. The -threshold for this to be true is not precisely defined by law. - - If such an object file uses only numerical parameters, data -structure layouts and accessors, and small macros and small inline -functions (ten lines or less in length), then the use of the object -file is unrestricted, regardless of whether it is legally a derivative -work. (Executables containing this object code plus portions of the -Library will still fall under Section 6.) - - Otherwise, if the work is a derivative of the Library, you may -distribute the object code for the work under the terms of Section 6. -Any executables containing that work also fall under Section 6, -whether or not they are linked directly with the Library itself. - - 6. As an exception to the Sections above, you may also combine or -link a "work that uses the Library" with the Library to produce a -work containing portions of the Library, and distribute that work -under terms of your choice, provided that the terms permit -modification of the work for the customer's own use and reverse -engineering for debugging such modifications. - - You must give prominent notice with each copy of the work that the -Library is used in it and that the Library and its use are covered by -this License. You must supply a copy of this License. If the work -during execution displays copyright notices, you must include the -copyright notice for the Library among them, as well as a reference -directing the user to the copy of this License. Also, you must do one -of these things: - - a) Accompany the work with the complete corresponding - machine-readable source code for the Library including whatever - changes were used in the work (which must be distributed under - Sections 1 and 2 above); and, if the work is an executable linked - with the Library, with the complete machine-readable "work that - uses the Library", as object code and/or source code, so that the - user can modify the Library and then relink to produce a modified - executable containing the modified Library. (It is understood - that the user who changes the contents of definitions files in the - Library will not necessarily be able to recompile the application - to use the modified definitions.) - - b) Use a suitable shared library mechanism for linking with the - Library. A suitable mechanism is one that (1) uses at run time a - copy of the library already present on the user's computer system, - rather than copying library functions into the executable, and (2) - will operate properly with a modified version of the library, if - the user installs one, as long as the modified version is - interface-compatible with the version that the work was made with. - - c) Accompany the work with a written offer, valid for at - least three years, to give the same user the materials - specified in Subsection 6a, above, for a charge no more - than the cost of performing this distribution. - - d) If distribution of the work is made by offering access to copy - from a designated place, offer equivalent access to copy the above - specified materials from the same place. - - e) Verify that the user has already received a copy of these - materials or that you have already sent this user a copy. - - For an executable, the required form of the "work that uses the -Library" must include any data and utility programs needed for -reproducing the executable from it. However, as a special exception, -the materials to be distributed need not include anything that is -normally distributed (in either source or binary form) with the major -components (compiler, kernel, and so on) of the operating system on -which the executable runs, unless that component itself accompanies -the executable. - - It may happen that this requirement contradicts the license -restrictions of other proprietary libraries that do not normally -accompany the operating system. Such a contradiction means you cannot -use both them and the Library together in an executable that you -distribute. - - 7. You may place library facilities that are a work based on the -Library side-by-side in a single library together with other library -facilities not covered by this License, and distribute such a combined -library, provided that the separate distribution of the work based on -the Library and of the other library facilities is otherwise -permitted, and provided that you do these two things: - - a) Accompany the combined library with a copy of the same work - based on the Library, uncombined with any other library - facilities. This must be distributed under the terms of the - Sections above. - - b) Give prominent notice with the combined library of the fact - that part of it is a work based on the Library, and explaining - where to find the accompanying uncombined form of the same work. - - 8. You may not copy, modify, sublicense, link with, or distribute -the Library except as expressly provided under this License. Any -attempt otherwise to copy, modify, sublicense, link with, or -distribute the Library is void, and will automatically terminate your -rights under this License. However, parties who have received copies, -or rights, from you under this License will not have their licenses -terminated so long as such parties remain in full compliance. - - 9. You are not required to accept this License, since you have not -signed it. However, nothing else grants you permission to modify or -distribute the Library or its derivative works. These actions are -prohibited by law if you do not accept this License. Therefore, by -modifying or distributing the Library (or any work based on the -Library), you indicate your acceptance of this License to do so, and -all its terms and conditions for copying, distributing or modifying -the Library or works based on it. - - 10. Each time you redistribute the Library (or any work based on the -Library), the recipient automatically receives a license from the -original licensor to copy, distribute, link with or modify the Library -subject to these terms and conditions. You may not impose any further -restrictions on the recipients' exercise of the rights granted herein. -You are not responsible for enforcing compliance by third parties with -this License. - - 11. If, as a consequence of a court judgment or allegation of patent -infringement or for any other reason (not limited to patent issues), -conditions are imposed on you (whether by court order, agreement or -otherwise) that contradict the conditions of this License, they do not -excuse you from the conditions of this License. If you cannot -distribute so as to satisfy simultaneously your obligations under this -License and any other pertinent obligations, then as a consequence you -may not distribute the Library at all. For example, if a patent -license would not permit royalty-free redistribution of the Library by -all those who receive copies directly or indirectly through you, then -the only way you could satisfy both it and this License would be to -refrain entirely from distribution of the Library. - -If any portion of this section is held invalid or unenforceable under any -particular circumstance, the balance of the section is intended to apply, -and the section as a whole is intended to apply in other circumstances. - -It is not the purpose of this section to induce you to infringe any -patents or other property right claims or to contest validity of any -such claims; this section has the sole purpose of protecting the -integrity of the free software distribution system which is -implemented by public license practices. Many people have made -generous contributions to the wide range of software distributed -through that system in reliance on consistent application of that -system; it is up to the author/donor to decide if he or she is willing -to distribute software through any other system and a licensee cannot -impose that choice. - -This section is intended to make thoroughly clear what is believed to -be a consequence of the rest of this License. - - 12. If the distribution and/or use of the Library is restricted in -certain countries either by patents or by copyrighted interfaces, the -original copyright holder who places the Library under this License may add -an explicit geographical distribution limitation excluding those countries, -so that distribution is permitted only in or among countries not thus -excluded. In such case, this License incorporates the limitation as if -written in the body of this License. - - 13. The Free Software Foundation may publish revised and/or new -versions of the Lesser General Public License from time to time. -Such new versions will be similar in spirit to the present version, -but may differ in detail to address new problems or concerns. - -Each version is given a distinguishing version number. If the Library -specifies a version number of this License which applies to it and -"any later version", you have the option of following the terms and -conditions either of that version or of any later version published by -the Free Software Foundation. If the Library does not specify a -license version number, you may choose any version ever published by -the Free Software Foundation. - - 14. If you wish to incorporate parts of the Library into other free -programs whose distribution conditions are incompatible with these, -write to the author to ask for permission. For software which is -copyrighted by the Free Software Foundation, write to the Free -Software Foundation; we sometimes make exceptions for this. Our -decision will be guided by the two goals of preserving the free status -of all derivatives of our free software and of promoting the sharing -and reuse of software generally. - - NO WARRANTY - - 15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO -WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. -EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR -OTHER PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY OF ANY -KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE -IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR -PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE -LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME -THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. - - 16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN -WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY -AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU -FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR -CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE -LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING -RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A -FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF -SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH -DAMAGES. - diff --git a/libraries/Firmata/examples/StandardFirmata/Makefile b/libraries/Firmata/examples/StandardFirmata/Makefile deleted file mode 100644 index 835187a..0000000 --- a/libraries/Firmata/examples/StandardFirmata/Makefile +++ /dev/null @@ -1,273 +0,0 @@ -# Arduino makefile -# -# This makefile allows you to build sketches from the command line -# without the Arduino environment (or Java). -# -# The Arduino environment does preliminary processing on a sketch before -# compiling it. If you're using this makefile instead, you'll need to do -# a few things differently: -# -# - Give your program's file a .cpp extension (e.g. foo.cpp). -# -# - Put this line at top of your code: #include <WProgram.h> -# -# - Write prototypes for all your functions (or define them before you -# call them). A prototype declares the types of parameters a -# function will take and what type of value it will return. This -# means that you can have a call to a function before the definition -# of the function. A function prototype looks like the first line of -# the function, with a semi-colon at the end. For example: -# int digitalRead(int pin); -# -# Instructions for using the makefile: -# -# 1. Copy this file into the folder with your sketch. -# -# 2. Below, modify the line containing "TARGET" to refer to the name of -# of your program's file without an extension (e.g. TARGET = foo). -# -# 3. Modify the line containg "ARDUINO" to point the directory that -# contains the Arduino core (for normal Arduino installations, this -# is the hardware/cores/arduino sub-directory). -# -# 4. Modify the line containing "PORT" to refer to the filename -# representing the USB or serial connection to your Arduino board -# (e.g. PORT = /dev/tty.USB0). If the exact name of this file -# changes, you can use * as a wildcard (e.g. PORT = /dev/tty.USB*). -# -# 5. At the command line, change to the directory containing your -# program's file and the makefile. -# -# 6. Type "make" and press enter to compile/verify your program. -# -# 7. Type "make upload", reset your Arduino board, and press enter to -# upload your program to the Arduino board. -# -# $Id: Makefile,v 1.7 2007/04/13 05:28:23 eighthave Exp $ - -PORT = /dev/tty.usbserial-* -TARGET := $(shell pwd | sed 's|.*/\(.*\)|\1|') -ARDUINO = /Applications/arduino -ARDUINO_SRC = $(ARDUINO)/hardware/cores/arduino -ARDUINO_LIB_SRC = $(ARDUINO)/hardware/libraries -ARDUINO_TOOLS = $(ARDUINO)/hardware/tools -INCLUDE = -I$(ARDUINO_SRC) -I$(ARDUINO)/hardware/tools/avr/avr/include \ - -I$(ARDUINO_LIB_SRC)/EEPROM \ - -I$(ARDUINO_LIB_SRC)/Firmata \ - -I$(ARDUINO_LIB_SRC)/Matrix \ - -I$(ARDUINO_LIB_SRC)/Servo \ - -I$(ARDUINO_LIB_SRC)/Wire \ - -I$(ARDUINO_LIB_SRC) -SRC = $(wildcard $(ARDUINO_SRC)/*.c) -CXXSRC = applet/$(TARGET).cpp $(ARDUINO_SRC)/HardwareSerial.cpp \ - $(ARDUINO_LIB_SRC)/EEPROM/EEPROM.cpp \ - $(ARDUINO_LIB_SRC)/Firmata/Firmata.cpp \ - $(ARDUINO_LIB_SRC)/Servo/Servo.cpp \ - $(ARDUINO_SRC)/Print.cpp \ - $(ARDUINO_SRC)/WMath.cpp -HEADERS = $(wildcard $(ARDUINO_SRC)/*.h) $(wildcard $(ARDUINO_LIB_SRC)/*/*.h) - -MCU = atmega168 -#MCU = atmega8 -F_CPU = 16000000 -FORMAT = ihex -UPLOAD_RATE = 19200 - -# Name of this Makefile (used for "make depend"). -MAKEFILE = Makefile - -# Debugging format. -# Native formats for AVR-GCC's -g are stabs [default], or dwarf-2. -# AVR (extended) COFF requires stabs, plus an avr-objcopy run. -DEBUG = stabs - -OPT = s - -# Place -D or -U options here -CDEFS = -DF_CPU=$(F_CPU) -CXXDEFS = -DF_CPU=$(F_CPU) - -# Compiler flag to set the C Standard level. -# c89 - "ANSI" C -# gnu89 - c89 plus GCC extensions -# c99 - ISO C99 standard (not yet fully implemented) -# gnu99 - c99 plus GCC extensions -CSTANDARD = -std=gnu99 -CDEBUG = -g$(DEBUG) -CWARN = -Wall -Wstrict-prototypes -CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums -#CEXTRA = -Wa,-adhlns=$(<:.c=.lst) - -CFLAGS = $(CDEBUG) $(CDEFS) $(INCLUDE) -O$(OPT) $(CWARN) $(CSTANDARD) $(CEXTRA) -CXXFLAGS = $(CDEFS) $(INCLUDE) -O$(OPT) -#ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs -LDFLAGS = - - -# Programming support using avrdude. Settings and variables. -AVRDUDE_PROGRAMMER = stk500 -AVRDUDE_PORT = $(PORT) -AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex -AVRDUDE_FLAGS = -F -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) \ - -b $(UPLOAD_RATE) -q -V - -# Program settings -ARDUINO_AVR_BIN = $(ARDUINO_TOOLS)/avr/bin -CC = $(ARDUINO_AVR_BIN)/avr-gcc -CXX = $(ARDUINO_AVR_BIN)/avr-g++ -OBJCOPY = $(ARDUINO_AVR_BIN)/avr-objcopy -OBJDUMP = $(ARDUINO_AVR_BIN)/avr-objdump -SIZE = $(ARDUINO_AVR_BIN)/avr-size -NM = $(ARDUINO_AVR_BIN)/avr-nm -#AVRDUDE = $(ARDUINO_AVR_BIN)/avrdude -AVRDUDE = avrdude -REMOVE = rm -f -MV = mv -f - -# Define all object files. -OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o) - -# Define all listing files. -LST = $(ASRC:.S=.lst) $(CXXSRC:.cpp=.lst) $(SRC:.c=.lst) - -# Combine all necessary flags and optional flags. -# Add target processor to flags. -ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) -ALL_CXXFLAGS = -mmcu=$(MCU) -I. $(CXXFLAGS) -ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS) - - -# Default target. -all: build - -build: applet/$(TARGET).hex - -eep: applet/$(TARGET).eep -lss: applet/$(TARGET).lss -sym: applet/$(TARGET).sym - - -# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB. -COFFCONVERT=$(OBJCOPY) --debugging \ ---change-section-address .data-0x800000 \ ---change-section-address .bss-0x800000 \ ---change-section-address .noinit-0x800000 \ ---change-section-address .eeprom-0x810000 - - -coff: applet/$(TARGET).elf - $(COFFCONVERT) -O coff-avr applet/$(TARGET).elf applet/$(TARGET).cof - - -extcoff: applet/$(TARGET).elf - $(COFFCONVERT) -O coff-ext-avr applet/$(TARGET).elf applet/$(TARGET).cof - - -.SUFFIXES: .elf .hex .eep .lss .sym .pde - -.elf.hex: - $(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@ - -.elf.eep: - -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \ - --change-section-lma .eeprom=0 -O $(FORMAT) $< $@ - -# Create extended listing file from ELF output file. -.elf.lss: - $(OBJDUMP) -h -S $< > $@ - -# Create a symbol table from ELF output file. -.elf.sym: - $(NM) -n $< > $@ - - -# Compile: create object files from C++ source files. -.cpp.o: $(HEADERS) - $(CXX) -c $(ALL_CXXFLAGS) $< -o $@ - -# Compile: create object files from C source files. -.c.o: $(HEADERS) - $(CC) -c $(ALL_CFLAGS) $< -o $@ - - -# Compile: create assembler files from C source files. -.c.s: - $(CC) -S $(ALL_CFLAGS) $< -o $@ - - -# Assemble: create object files from assembler source files. -.S.o: - $(CC) -c $(ALL_ASFLAGS) $< -o $@ - - - -applet/$(TARGET).cpp: $(TARGET).pde - test -d applet || mkdir applet - echo '#include "WProgram.h"' > applet/$(TARGET).cpp - echo '#include "avr/interrupt.h"' >> applet/$(TARGET).cpp - sed -n 's|^\(void .*)\).*|\1;|p' $(TARGET).pde | grep -v 'setup()' | \ - grep -v 'loop()' >> applet/$(TARGET).cpp - cat $(TARGET).pde >> applet/$(TARGET).cpp - cat $(ARDUINO_SRC)/main.cxx >> applet/$(TARGET).cpp - -# Link: create ELF output file from object files. -applet/$(TARGET).elf: applet/$(TARGET).cpp $(OBJ) - $(CC) $(ALL_CFLAGS) $(OBJ) -lm --output $@ $(LDFLAGS) -# $(CC) $(ALL_CFLAGS) $(OBJ) $(ARDUINO_TOOLS)/avr/avr/lib/avr5/crtm168.o --output $@ $(LDFLAGS) - -pd_close_serial: - echo 'close;' | /Applications/Pd-extended.app/Contents/Resources/bin/pdsend 34567 || true - -# Program the device. -upload: applet/$(TARGET).hex - $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) - - -pd_test: build pd_close_serial upload - -# Target: clean project. -clean: - $(REMOVE) -- applet/$(TARGET).hex applet/$(TARGET).eep \ - applet/$(TARGET).cof applet/$(TARGET).elf $(TARGET).map \ - applet/$(TARGET).sym applet/$(TARGET).lss applet/$(TARGET).cpp \ - $(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d) - rmdir -- applet - -depend: - if grep '^# DO NOT DELETE' $(MAKEFILE) >/dev/null; \ - then \ - sed -e '/^# DO NOT DELETE/,$$d' $(MAKEFILE) > \ - $(MAKEFILE).$$$$ && \ - $(MV) $(MAKEFILE).$$$$ $(MAKEFILE); \ - fi - echo '# DO NOT DELETE THIS LINE -- make depend depends on it.' \ - >> $(MAKEFILE); \ - $(CC) -M -mmcu=$(MCU) $(CDEFS) $(INCLUDE) $(SRC) $(ASRC) >> $(MAKEFILE) - -.PHONY: all build eep lss sym coff extcoff clean depend pd_close_serial pd_test - -# for emacs -etags: - make etags_`uname -s` - etags *.pde \ - $(ARDUINO_SRC)/*.[ch] \ - $(ARDUINO_SRC)/*.cpp \ - $(ARDUINO_LIB_SRC)/*/*.[ch] \ - $(ARDUINO_LIB_SRC)/*/*.cpp \ - $(ARDUINO)/hardware/tools/avr/avr/include/avr/*.[ch] \ - $(ARDUINO)/hardware/tools/avr/avr/include/*.[ch] - -etags_Darwin: -# etags -a - -etags_Linux: -# etags -a /usr/include/*.h linux/input.h /usr/include/sys/*.h - -etags_MINGW: -# etags -a /usr/include/*.h /usr/include/sys/*.h - - -path: - echo $(PATH) - echo $$PATH - diff --git a/libraries/Firmata/examples/StandardFirmata/StandardFirmata.pde b/libraries/Firmata/examples/StandardFirmata/StandardFirmata.pde deleted file mode 100644 index 16c8b87..0000000 --- a/libraries/Firmata/examples/StandardFirmata/StandardFirmata.pde +++ /dev/null @@ -1,293 +0,0 @@ -/* - Copyright (C) 2006-2008 Hans-Christoph Steiner. All rights reserved. - - This library is free software; you can redistribute it and/or - modify it under the terms of the GNU Lesser General Public - License as published by the Free Software Foundation; either - version 2.1 of the License, or (at your option) any later version. - - See file LICENSE.txt for further informations on licensing terms. - - formatted using the GNU C formatting and indenting -*/ - - -/* - * TODO: add Servo support using setPinModeCallback(pin, SERVO); - * TODO: use Program Control to load stored profiles from EEPROM - */ - -#include <Firmata.h> -#include <Servo.h> - -/*============================================================================== - * GLOBAL VARIABLES - *============================================================================*/ - -/* analog inputs */ -int analogInputsToReport = 0; // bitwise array to store pin reporting -int analogPin = 0; // counter for reading analog pins - -/* digital pins */ -byte reportPINs[TOTAL_PORTS]; // PIN == input port -byte previousPINs[TOTAL_PORTS]; // PIN == input port -byte pinStatus[TOTAL_DIGITAL_PINS]; // store pin status, default OUTPUT -byte portStatus[TOTAL_PORTS]; - -/* timer variables */ -unsigned long currentMillis; // store the current value from millis() -unsigned long nextExecuteMillis; // for comparison with currentMillis -int samplingInterval = 19; // how often to run the main loop (in ms) - -Servo servos[2]; // the servo library can control servos on pins 9 and 10 only - -/*============================================================================== - * FUNCTIONS - *============================================================================*/ - -void outputPort(byte portNumber, byte portValue) -{ - portValue = portValue &~ portStatus[portNumber]; - if(previousPINs[portNumber] != portValue) { - Firmata.sendDigitalPort(portNumber, portValue); - previousPINs[portNumber] = portValue; - Firmata.sendDigitalPort(portNumber, portValue); - } -} - -/* ----------------------------------------------------------------------------- - * check all the active digital inputs for change of state, then add any events - * to the Serial output queue using Serial.print() */ -void checkDigitalInputs(void) -{ - byte i, tmp; - for(i=0; i < TOTAL_PORTS; i++) { - if(reportPINs[i]) { - switch(i) { - case 0: - outputPort(0, PIND &~ B00000011); // ignore Rx/Tx 0/1 - break; - case 1: - outputPort(1, PINB); - break; - case ANALOG_PORT: - outputPort(ANALOG_PORT, PINC); - break; - } - } - } -} - -// ----------------------------------------------------------------------------- -/* sets the pin mode to the correct state and sets the relevant bits in the - * two bit-arrays that track Digital I/O and PWM status - */ -void setPinModeCallback(byte pin, int mode) { - byte port = 0; - byte offset = 0; - - // TODO: abstract for different boards - if (pin < 8) { - port = 0; - offset = 0; - } else if (pin < 14) { - port = 1; - offset = 8; - } else if (pin < 22) { - port = 2; - offset = 14; - } - - if(pin > 1) { // ignore RxTx (pins 0 and 1) - if(pin > 13) - reportAnalogCallback(pin - 14, mode == ANALOG ? 1 : 0); // turn on/off reporting - switch(mode) { - case ANALOG: - digitalWrite(pin, LOW); // disable internal pull-ups and fall thru to 'case INPUT:' - case INPUT: - pinStatus[pin] = mode; - pinMode(pin, INPUT); - portStatus[port] = portStatus[port] &~ (1 << (pin - offset)); - break; - case OUTPUT: - digitalWrite(pin, LOW); // disable PWM and fall thru to 'case PWM:' - case PWM: - pinStatus[pin] = mode; - pinMode(pin, OUTPUT); - portStatus[port] = portStatus[port] | (1 << (pin - offset)); - break; - case SERVO: - if((pin == 9 || pin == 10)) - pinStatus[pin] = mode; - else - Firmata.sendString("Servo only on pins 9 and 10"); - break; - case I2C: - pinStatus[pin] = mode; - Firmata.sendString("I2C mode not yet supported"); - break; - default: - Firmata.sendString("Unknown pin mode"); // TODO: put error msgs in EEPROM - } - // TODO: save status to EEPROM here, if changed - } -} - -void analogWriteCallback(byte pin, int value) -{ - switch(pinStatus[pin]) { - case SERVO: - if(pin == 9) servos[0].write(value); - if(pin == 10) servos[1].write(value); - break; - case PWM: - analogWrite(pin, value); - break; - } -} - -void digitalWriteCallback(byte port, int value) -{ - switch(port) { - case 0: // pins 2-7 (don't change Rx/Tx, pins 0 and 1) - // 0xFF03 == B1111111100000011 0x03 == B00000011 - PORTD = (value &~ 0xFF03) | (PORTD & 0x03); - break; - case 1: // pins 8-13 (14,15 are disabled for the crystal) - PORTB = (byte)value; - break; - case 2: // analog pins used as digital - byte pin; - byte pinModeMask; - for(pin=0; pin<8; pin++) - if(pinStatus[pin] == OUTPUT) - pinModeMask += 1 << pin; - PORTC = (byte)value & pinModeMask; - break; - } -} - -// ----------------------------------------------------------------------------- -/* sets bits in a bit array (int) to toggle the reporting of the analogIns - */ -//void FirmataClass::setAnalogPinReporting(byte pin, byte state) { -//} -void reportAnalogCallback(byte pin, int value) -{ - if(value == 0) { - analogInputsToReport = analogInputsToReport &~ (1 << pin); - } - else { // everything but 0 enables reporting of that pin - analogInputsToReport = analogInputsToReport | (1 << pin); - setPinModeCallback(pin, ANALOG); - } - // TODO: save status to EEPROM here, if changed -} - -void reportDigitalCallback(byte port, int value) -{ - reportPINs[port] = (byte)value; - if(port == ANALOG_PORT) // turn off analog reporting when used as digital - analogInputsToReport = 0; -} - -/*============================================================================== - * SYSEX-BASED commands - *============================================================================*/ - -void sysexCallback(byte command, byte argc, byte *argv) -{ - switch(command) { - case SERVO_CONFIG: - if(argc > 4) { - // these vars are here for clarity, they'll optimized away by the compiler - byte pin = argv[0] - 9; // servos are pins 9 and 10, so offset for array - int minPulse = argv[1] + (argv[2] << 7); - int maxPulse = argv[3] + (argv[4] << 7); - servos[pin].attach(argv[0], minPulse, maxPulse); - // TODO does the Servo have to be detach()ed before reconfiguring? - setPinModeCallback(pin, SERVO); - } - break; - case SAMPLING_INTERVAL: - if (argc > 1) - samplingInterval = argv[0] + (argv[1] << 7); - else - Firmata.sendString("Not enough data"); - break; - } -} - - -/*============================================================================== - * SETUP() - *============================================================================*/ -void setup() -{ - byte i; - - Firmata.setFirmwareVersion(2, 1); - - Firmata.attach(ANALOG_MESSAGE, analogWriteCallback); - Firmata.attach(DIGITAL_MESSAGE, digitalWriteCallback); - Firmata.attach(REPORT_ANALOG, reportAnalogCallback); - Firmata.attach(REPORT_DIGITAL, reportDigitalCallback); - Firmata.attach(SET_PIN_MODE, setPinModeCallback); - Firmata.attach(START_SYSEX, sysexCallback); - - portStatus[0] = B00000011; // ignore Tx/RX pins - portStatus[1] = B11000000; // ignore 14/15 pins - portStatus[2] = B00000000; - - for(i=0; i<TOTAL_DIGITAL_PINS; ++i) { // TODO make this work with analogs - setPinModeCallback(i,OUTPUT); - } - // set all outputs to 0 to make sure internal pull-up resistors are off - PORTB = 0; // pins 8-15 - PORTC = 0; // analog port - PORTD = 0; // pins 0-7 - - // TODO rethink the init, perhaps it should report analog on default - for(i=0; i<TOTAL_PORTS; ++i) { - reportPINs[i] = false; - } - // TODO: load state from EEPROM here - - /* send digital inputs here, if enabled, to set the initial state on the - * host computer, since once in the loop(), this firmware will only send - * digital data on change. */ - if(reportPINs[0]) outputPort(0, PIND &~ B00000011); // ignore Rx/Tx 0/1 - if(reportPINs[1]) outputPort(1, PINB); - if(reportPINs[ANALOG_PORT]) outputPort(ANALOG_PORT, PINC); - - Firmata.begin(57600); -} - -/*============================================================================== - * LOOP() - *============================================================================*/ -void loop() -{ - /* DIGITALREAD - as fast as possible, check for changes and output them to the - * FTDI buffer using Serial.print() */ - checkDigitalInputs(); - currentMillis = millis(); - if(currentMillis > nextExecuteMillis) { - nextExecuteMillis = currentMillis + samplingInterval; - /* SERIALREAD - Serial.read() uses a 128 byte circular buffer, so handle - * all serialReads at once, i.e. empty the buffer */ - while(Firmata.available()) - Firmata.processInput(); - /* SEND FTDI WRITE BUFFER - make sure that the FTDI buffer doesn't go over - * 60 bytes. use a timer to sending an event character every 4 ms to - * trigger the buffer to dump. */ - - /* ANALOGREAD - right after the event character, do all of the - * analogReads(). These only need to be done every 4ms. */ - for(analogPin=0;analogPin<TOTAL_ANALOG_PINS;analogPin++) { - if( analogInputsToReport & (1 << analogPin) ) { - Firmata.sendAnalog(analogPin, analogRead(analogPin)); - } - } - } -} |