1 files changed, 0 insertions, 87 deletions
diff --git a/libraries/Ethernet/examples/DhcpChatServer/DhcpChatServer.ino b/libraries/Ethernet/examples/DhcpChatServer/DhcpChatServer.ino
deleted file mode 100644
index 09cbd43..0000000
--- a/libraries/Ethernet/examples/DhcpChatServer/DhcpChatServer.ino
+++ /dev/null
@@ -1,87 +0,0 @@
-/*
- DHCP Chat  Server
- 
- A simple server that distributes any incoming messages to all
- connected clients.  To use telnet to  your device's IP address and type.
- You can see the client's input in the serial monitor as well.
- Using an Arduino Wiznet Ethernet shield. 
- 
- THis version attempts to get an IP address using DHCP
- 
- Circuit:
- * Ethernet shield attached to pins 10, 11, 12, 13
- 
- created 21 May 2011
- modified 9 Apr 2012
- by Tom Igoe
- Based on ChatServer example by David A. Mellis
- 
- */
-
-#include <SPI.h>
-#include <Ethernet.h>
-
-// Enter a MAC address and IP address for your controller below.
-// The IP address will be dependent on your local network.
-// gateway and subnet are optional:
-byte mac[] = { 
-  0x00, 0xAA, 0xBB, 0xCC, 0xDE, 0x02 };
-IPAddress ip(192,168,1, 177);
-IPAddress gateway(192,168,1, 1);
-IPAddress subnet(255, 255, 0, 0);
-
-// telnet defaults to port 23
-EthernetServer server(23);
-boolean gotAMessage = false; // whether or not you got a message from the client yet
-
-void setup() {
-  // Open serial communications and wait for port to open:
-  Serial.begin(9600);
-  // this check is only needed on the Leonardo:
-   while (!Serial) {
-    ; // wait for serial port to connect. Needed for Leonardo only
-  }
-
-
-  // start the Ethernet connection:
-  Serial.println("Trying to get an IP address using DHCP");
-  if (Ethernet.begin(mac) == 0) {
-    Serial.println("Failed to configure Ethernet using DHCP");
-    // initialize the ethernet device not using DHCP:
-    Ethernet.begin(mac, ip, gateway, subnet);
-  }
-  // print your local IP address:
-  Serial.print("My IP address: ");
-  ip = Ethernet.localIP();
-  for (byte thisByte = 0; thisByte < 4; thisByte++) {
-    // print the value of each byte of the IP address:
-    Serial.print(ip[thisByte], DEC);
-    Serial.print("."); 
-  }
-  Serial.println();
-  // start listening for clients
-  server.begin();
- 
-}
-
-void loop() {
-  // wait for a new client:
-  EthernetClient client = server.available();
-
-  // when the client sends the first byte, say hello:
-  if (client) {
-    if (!gotAMessage) {
-      Serial.println("We have a new client");
-      client.println("Hello, client!"); 
-      gotAMessage = true;
-    }
-
-    // read the bytes incoming from the client:
-    char thisChar = client.read();
-    // echo the bytes back to the client:
-    server.write(thisChar);
-    // echo the bytes to the server as well:
-    Serial.print(thisChar);
-  }
-}
-