3 files changed, 0 insertions, 97 deletions
diff --git a/libraries/EEPROM/examples/eeprom_clear/eeprom_clear.pde b/libraries/EEPROM/examples/eeprom_clear/eeprom_clear.pde
deleted file mode 100644
index 36af68e..0000000
--- a/libraries/EEPROM/examples/eeprom_clear/eeprom_clear.pde
+++ /dev/null
@@ -1,21 +0,0 @@
-/*
- * EEPROM Clear
- *
- * Sets all of the bytes of the EEPROM to 0.
- */
-
-#include <EEPROM.h>
-
-void setup()
-{
-  // write a 0 to all 512 bytes of the EEPROM
-  for (int i = 0; i < 512; i++)
-    EEPROM.write(i, 0);
-    
-  // turn the LED on when we're done
-  digitalWrite(13, HIGH);
-}
-
-void loop()
-{
-}
diff --git a/libraries/EEPROM/examples/eeprom_read/eeprom_read.pde b/libraries/EEPROM/examples/eeprom_read/eeprom_read.pde
deleted file mode 100644
index 2e30708..0000000
--- a/libraries/EEPROM/examples/eeprom_read/eeprom_read.pde
+++ /dev/null
@@ -1,38 +0,0 @@
-/*
- * EEPROM Read
- *
- * Reads the value of each byte of the EEPROM and prints it 
- * to the computer.
- */
-
-#include <EEPROM.h>
-
-// start reading from the first byte (address 0) of the EEPROM
-int address = 0;
-byte value;
-
-void setup()
-{
-  Serial.begin(9600);
-}
-
-void loop()
-{
-  // read a byte from the current address of the EEPROM
-  value = EEPROM.read(address);
-  
-  Serial.print(address);
-  Serial.print("\t");
-  Serial.print(value, DEC);
-  Serial.println();
-  
-  // advance to the next address of the EEPROM
-  address = address + 1;
-  
-  // there are only 512 bytes of EEPROM, from 0 to 511, so if we're
-  // on address 512, wrap around to address 0
-  if (address == 512)
-    address = 0;
-    
-  delay(500);
-}
diff --git a/libraries/EEPROM/examples/eeprom_write/eeprom_write.pde b/libraries/EEPROM/examples/eeprom_write/eeprom_write.pde
deleted file mode 100644
index ae7c57e..0000000
--- a/libraries/EEPROM/examples/eeprom_write/eeprom_write.pde
+++ /dev/null
@@ -1,38 +0,0 @@
-/*
- * EEPROM Write
- *
- * Stores values read from analog input 0 into the EEPROM.
- * These values will stay in the EEPROM when the board is
- * turned off and may be retrieved later by another sketch.
- */
-
-#include <EEPROM.h>
-
-// the current address in the EEPROM (i.e. which byte
-// we're going to write to next)
-int addr = 0;
-
-void setup()
-{
-}
-
-void loop()
-{
-  // need to divide by 4 because analog inputs range from
-  // 0 to 1023 and each byte of the EEPROM can only hold a
-  // value from 0 to 255.
-  int val = analogRead(0) / 4;
-  
-  // write the value to the appropriate byte of the EEPROM.
-  // these values will remain there when the board is
-  // turned off.
-  EEPROM.write(addr, val);
-  
-  // advance to the next address.  there are 512 bytes in 
-  // the EEPROM, so go back to 0 when we hit 512.
-  addr = addr + 1;
-  if (addr == 512)
-    addr = 0;
-  
-  delay(100);
-}