diff options
Diffstat (limited to 'firmwares/atmegaxxu2/arduino-usbdfu/Arduino-usbdfu.c')
| -rw-r--r-- | firmwares/atmegaxxu2/arduino-usbdfu/Arduino-usbdfu.c | 728 |
1 files changed, 0 insertions, 728 deletions
diff --git a/firmwares/atmegaxxu2/arduino-usbdfu/Arduino-usbdfu.c b/firmwares/atmegaxxu2/arduino-usbdfu/Arduino-usbdfu.c deleted file mode 100644 index 7bed831..0000000 --- a/firmwares/atmegaxxu2/arduino-usbdfu/Arduino-usbdfu.c +++ /dev/null @@ -1,728 +0,0 @@ -/*
- LUFA Library
- Copyright (C) Dean Camera, 2010.
-
- dean [at] fourwalledcubicle [dot] com
- www.fourwalledcubicle.com
-*/
-
-/*
- Copyright 2010 Dean Camera (dean [at] fourwalledcubicle [dot] com)
-
- Permission to use, copy, modify, distribute, and sell this
- software and its documentation for any purpose is hereby granted
- without fee, provided that the above copyright notice appear in
- all copies and that both that the copyright notice and this
- permission notice and warranty disclaimer appear in supporting
- documentation, and that the name of the author not be used in
- advertising or publicity pertaining to distribution of the
- software without specific, written prior permission.
-
- The author disclaim all warranties with regard to this
- software, including all implied warranties of merchantability
- and fitness. In no event shall the author be liable for any
- special, indirect or consequential damages or any damages
- whatsoever resulting from loss of use, data or profits, whether
- in an action of contract, negligence or other tortious action,
- arising out of or in connection with the use or performance of
- this software.
-*/
-
-/** \file
- *
- * Main source file for the DFU class bootloader. This file contains the complete bootloader logic.
- */
-
-#define INCLUDE_FROM_BOOTLOADER_C
-#include "Arduino-usbdfu.h"
-
-/** Flag to indicate if the bootloader should be running, or should exit and allow the application code to run
- * via a soft reset. When cleared, the bootloader will abort, the USB interface will shut down and the application
- * jumped to via an indirect jump to location 0x0000 (or other location specified by the host).
- */
-bool RunBootloader = true;
-
-/** Flag to indicate if the bootloader is waiting to exit. When the host requests the bootloader to exit and
- * jump to the application address it specifies, it sends two sequential commands which must be properly
- * acknowledged. Upon reception of the first the RunBootloader flag is cleared and the WaitForExit flag is set,
- * causing the bootloader to wait for the final exit command before shutting down.
- */
-bool WaitForExit = false;
-
-/** Current DFU state machine state, one of the values in the DFU_State_t enum. */
-uint8_t DFU_State = dfuIDLE;
-
-/** Status code of the last executed DFU command. This is set to one of the values in the DFU_Status_t enum after
- * each operation, and returned to the host when a Get Status DFU request is issued.
- */
-uint8_t DFU_Status = OK;
-
-/** Data containing the DFU command sent from the host. */
-DFU_Command_t SentCommand;
-
-/** Response to the last issued Read Data DFU command. Unlike other DFU commands, the read command
- * requires a single byte response from the bootloader containing the read data when the next DFU_UPLOAD command
- * is issued by the host.
- */
-uint8_t ResponseByte;
-
-/** Pointer to the start of the user application. By default this is 0x0000 (the reset vector), however the host
- * may specify an alternate address when issuing the application soft-start command.
- */
-AppPtr_t AppStartPtr = (AppPtr_t)0x0000;
-
-/** 64-bit flash page number. This is concatenated with the current 16-bit address on USB AVRs containing more than
- * 64KB of flash memory.
- */
-uint8_t Flash64KBPage = 0;
-
-/** Memory start address, indicating the current address in the memory being addressed (either FLASH or EEPROM
- * depending on the issued command from the host).
- */
-uint16_t StartAddr = 0x0000;
-
-/** Memory end address, indicating the end address to read to/write from in the memory being addressed (either FLASH
- * of EEPROM depending on the issued command from the host).
- */
-uint16_t EndAddr = 0x0000;
-
-
-/** Pulse generation counters to keep track of the number of milliseconds remaining for each pulse type */
-volatile struct
-{
- uint8_t TxLEDPulse; /**< Milliseconds remaining for data Tx LED pulse */
- uint8_t RxLEDPulse; /**< Milliseconds remaining for data Rx LED pulse */
- uint8_t PingPongLEDPulse; /**< Milliseconds remaining for enumeration Tx/Rx ping-pong LED pulse */
-} PulseMSRemaining;
-
-/** Main program entry point. This routine configures the hardware required by the bootloader, then continuously
- * runs the bootloader processing routine until instructed to soft-exit, or hard-reset via the watchdog to start
- * the loaded application code.
- */
-int main(void)
-{
- /* Configure hardware required by the bootloader */
- SetupHardware();
-
- /* Enable global interrupts so that the USB stack can function */
- sei();
-
- /* Run the USB management task while the bootloader is supposed to be running */
- while (RunBootloader || WaitForExit)
- USB_USBTask();
-
- /* Reset configured hardware back to their original states for the user application */
- ResetHardware();
-
- /* Start the user application */
- AppStartPtr();
-}
-
-/** Configures all hardware required for the bootloader. */
-void SetupHardware(void)
-{
- /* Disable watchdog if enabled by bootloader/fuses */
- MCUSR &= ~(1 << WDRF);
- wdt_disable();
-
- /* Disable clock division */
-// clock_prescale_set(clock_div_1);
-
- /* Relocate the interrupt vector table to the bootloader section */
- MCUCR = (1 << IVCE);
- MCUCR = (1 << IVSEL);
-
- LEDs_Init();
-
- /* Initialize the USB subsystem */
- USB_Init();
-}
-
-/** Resets all configured hardware required for the bootloader back to their original states. */
-void ResetHardware(void)
-{
- /* Shut down the USB subsystem */
- USB_ShutDown();
-
- /* Relocate the interrupt vector table back to the application section */
- MCUCR = (1 << IVCE);
- MCUCR = 0;
-}
-
-/** Event handler for the USB_UnhandledControlRequest event. This is used to catch standard and class specific
- * control requests that are not handled internally by the USB library (including the DFU commands, which are
- * all issued via the control endpoint), so that they can be handled appropriately for the application.
- */
-void EVENT_USB_Device_UnhandledControlRequest(void)
-{
- /* Get the size of the command and data from the wLength value */
- SentCommand.DataSize = USB_ControlRequest.wLength;
-
- /* Turn off TX LED(s) once the TX pulse period has elapsed */
- if (PulseMSRemaining.TxLEDPulse && !(--PulseMSRemaining.TxLEDPulse))
- LEDs_TurnOffLEDs(LEDMASK_TX);
-
- /* Turn off RX LED(s) once the RX pulse period has elapsed */
- if (PulseMSRemaining.RxLEDPulse && !(--PulseMSRemaining.RxLEDPulse))
- LEDs_TurnOffLEDs(LEDMASK_RX);
-
- switch (USB_ControlRequest.bRequest)
- {
- case DFU_DNLOAD:
- LEDs_TurnOnLEDs(LEDMASK_RX);
- PulseMSRemaining.RxLEDPulse = TX_RX_LED_PULSE_MS;
-
- Endpoint_ClearSETUP();
-
- /* Check if bootloader is waiting to terminate */
- if (WaitForExit)
- {
- /* Bootloader is terminating - process last received command */
- ProcessBootloaderCommand();
-
- /* Turn off TX/RX status LEDs so that they're not left on when application starts */
- LEDs_TurnOffLEDs(LEDMASK_TX);
- LEDs_TurnOffLEDs(LEDMASK_RX);
-
- /* Indicate that the last command has now been processed - free to exit bootloader */
- WaitForExit = false;
- }
-
- /* If the request has a data stage, load it into the command struct */
- if (SentCommand.DataSize)
- {
- while (!(Endpoint_IsOUTReceived()))
- {
- if (USB_DeviceState == DEVICE_STATE_Unattached)
- return;
- }
-
- /* First byte of the data stage is the DNLOAD request's command */
- SentCommand.Command = Endpoint_Read_Byte();
-
- /* One byte of the data stage is the command, so subtract it from the total data bytes */
- SentCommand.DataSize--;
-
- /* Load in the rest of the data stage as command parameters */
- for (uint8_t DataByte = 0; (DataByte < sizeof(SentCommand.Data)) &&
- Endpoint_BytesInEndpoint(); DataByte++)
- {
- SentCommand.Data[DataByte] = Endpoint_Read_Byte();
- SentCommand.DataSize--;
- }
-
- /* Process the command */
- ProcessBootloaderCommand();
- }
-
- /* Check if currently downloading firmware */
- if (DFU_State == dfuDNLOAD_IDLE)
- {
- if (!(SentCommand.DataSize))
- {
- DFU_State = dfuIDLE;
- }
- else
- {
- /* Throw away the filler bytes before the start of the firmware */
- DiscardFillerBytes(DFU_FILLER_BYTES_SIZE);
-
- /* Throw away the packet alignment filler bytes before the start of the firmware */
- DiscardFillerBytes(StartAddr % FIXED_CONTROL_ENDPOINT_SIZE);
-
- /* Calculate the number of bytes remaining to be written */
- uint16_t BytesRemaining = ((EndAddr - StartAddr) + 1);
-
- if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x00)) // Write flash
- {
- /* Calculate the number of words to be written from the number of bytes to be written */
- uint16_t WordsRemaining = (BytesRemaining >> 1);
-
- union
- {
- uint16_t Words[2];
- uint32_t Long;
- } CurrFlashAddress = {.Words = {StartAddr, Flash64KBPage}};
-
- uint32_t CurrFlashPageStartAddress = CurrFlashAddress.Long;
- uint8_t WordsInFlashPage = 0;
-
- while (WordsRemaining--)
- {
- /* Check if endpoint is empty - if so clear it and wait until ready for next packet */
- if (!(Endpoint_BytesInEndpoint()))
- {
- Endpoint_ClearOUT();
-
- while (!(Endpoint_IsOUTReceived()))
- {
- if (USB_DeviceState == DEVICE_STATE_Unattached)
- return;
- }
- }
-
- /* Write the next word into the current flash page */
- boot_page_fill(CurrFlashAddress.Long, Endpoint_Read_Word_LE());
-
- /* Adjust counters */
- WordsInFlashPage += 1;
- CurrFlashAddress.Long += 2;
-
- /* See if an entire page has been written to the flash page buffer */
- if ((WordsInFlashPage == (SPM_PAGESIZE >> 1)) || !(WordsRemaining))
- {
- /* Commit the flash page to memory */
- boot_page_write(CurrFlashPageStartAddress);
- boot_spm_busy_wait();
-
- /* Check if programming incomplete */
- if (WordsRemaining)
- {
- CurrFlashPageStartAddress = CurrFlashAddress.Long;
- WordsInFlashPage = 0;
-
- /* Erase next page's temp buffer */
- boot_page_erase(CurrFlashAddress.Long);
- boot_spm_busy_wait();
- }
- }
- }
-
- /* Once programming complete, start address equals the end address */
- StartAddr = EndAddr;
-
- /* Re-enable the RWW section of flash */
- boot_rww_enable();
- }
- else // Write EEPROM
- {
- while (BytesRemaining--)
- {
- /* Check if endpoint is empty - if so clear it and wait until ready for next packet */
- if (!(Endpoint_BytesInEndpoint()))
- {
- Endpoint_ClearOUT();
-
- while (!(Endpoint_IsOUTReceived()))
- {
- if (USB_DeviceState == DEVICE_STATE_Unattached)
- return;
- }
- }
-
- /* Read the byte from the USB interface and write to to the EEPROM */
- eeprom_write_byte((uint8_t*)StartAddr, Endpoint_Read_Byte());
-
- /* Adjust counters */
- StartAddr++;
- }
- }
-
- /* Throw away the currently unused DFU file suffix */
- DiscardFillerBytes(DFU_FILE_SUFFIX_SIZE);
- }
- }
-
- Endpoint_ClearOUT();
-
- Endpoint_ClearStatusStage();
-
- break;
- case DFU_UPLOAD:
- Endpoint_ClearSETUP();
-
- LEDs_TurnOnLEDs(LEDMASK_TX);
- PulseMSRemaining.TxLEDPulse = TX_RX_LED_PULSE_MS;
-
- while (!(Endpoint_IsINReady()))
- {
- if (USB_DeviceState == DEVICE_STATE_Unattached)
- return;
- }
-
- if (DFU_State != dfuUPLOAD_IDLE)
- {
- if ((DFU_State == dfuERROR) && IS_ONEBYTE_COMMAND(SentCommand.Data, 0x01)) // Blank Check
- {
- /* Blank checking is performed in the DFU_DNLOAD request - if we get here we've told the host
- that the memory isn't blank, and the host is requesting the first non-blank address */
- Endpoint_Write_Word_LE(StartAddr);
- }
- else
- {
- /* Idle state upload - send response to last issued command */
- Endpoint_Write_Byte(ResponseByte);
- }
- }
- else
- {
- /* Determine the number of bytes remaining in the current block */
- uint16_t BytesRemaining = ((EndAddr - StartAddr) + 1);
-
- if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x00)) // Read FLASH
- {
- /* Calculate the number of words to be written from the number of bytes to be written */
- uint16_t WordsRemaining = (BytesRemaining >> 1);
-
- union
- {
- uint16_t Words[2];
- uint32_t Long;
- } CurrFlashAddress = {.Words = {StartAddr, Flash64KBPage}};
-
- while (WordsRemaining--)
- {
- /* Check if endpoint is full - if so clear it and wait until ready for next packet */
- if (Endpoint_BytesInEndpoint() == FIXED_CONTROL_ENDPOINT_SIZE)
- {
- Endpoint_ClearIN();
-
- while (!(Endpoint_IsINReady()))
- {
- if (USB_DeviceState == DEVICE_STATE_Unattached)
- return;
- }
- }
-
- /* Read the flash word and send it via USB to the host */
- #if (FLASHEND > 0xFFFF)
- Endpoint_Write_Word_LE(pgm_read_word_far(CurrFlashAddress.Long));
- #else
- Endpoint_Write_Word_LE(pgm_read_word(CurrFlashAddress.Long));
- #endif
-
- /* Adjust counters */
- CurrFlashAddress.Long += 2;
- }
-
- /* Once reading is complete, start address equals the end address */
- StartAddr = EndAddr;
- }
- else if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x02)) // Read EEPROM
- {
- while (BytesRemaining--)
- {
- /* Check if endpoint is full - if so clear it and wait until ready for next packet */
- if (Endpoint_BytesInEndpoint() == FIXED_CONTROL_ENDPOINT_SIZE)
- {
- Endpoint_ClearIN();
-
- while (!(Endpoint_IsINReady()))
- {
- if (USB_DeviceState == DEVICE_STATE_Unattached)
- return;
- }
- }
-
- /* Read the EEPROM byte and send it via USB to the host */
- Endpoint_Write_Byte(eeprom_read_byte((uint8_t*)StartAddr));
-
- /* Adjust counters */
- StartAddr++;
- }
- }
-
- /* Return to idle state */
- DFU_State = dfuIDLE;
- }
-
- Endpoint_ClearIN();
-
- Endpoint_ClearStatusStage();
- break;
- case DFU_GETSTATUS:
- Endpoint_ClearSETUP();
-
- /* Write 8-bit status value */
- Endpoint_Write_Byte(DFU_Status);
-
- /* Write 24-bit poll timeout value */
- Endpoint_Write_Byte(0);
- Endpoint_Write_Word_LE(0);
-
- /* Write 8-bit state value */
- Endpoint_Write_Byte(DFU_State);
-
- /* Write 8-bit state string ID number */
- Endpoint_Write_Byte(0);
-
- Endpoint_ClearIN();
-
- Endpoint_ClearStatusStage();
- break;
- case DFU_CLRSTATUS:
- Endpoint_ClearSETUP();
-
- /* Reset the status value variable to the default OK status */
- DFU_Status = OK;
-
- Endpoint_ClearStatusStage();
- break;
- case DFU_GETSTATE:
- Endpoint_ClearSETUP();
-
- /* Write the current device state to the endpoint */
- Endpoint_Write_Byte(DFU_State);
-
- Endpoint_ClearIN();
-
- Endpoint_ClearStatusStage();
- break;
- case DFU_ABORT:
- Endpoint_ClearSETUP();
-
- /* Turn off TX/RX status LEDs so that they're not left on when application starts */
- LEDs_TurnOffLEDs(LEDMASK_TX);
- LEDs_TurnOffLEDs(LEDMASK_RX);
-
- /* Reset the current state variable to the default idle state */
- DFU_State = dfuIDLE;
-
- Endpoint_ClearStatusStage();
- break;
- }
-}
-
-/** Routine to discard the specified number of bytes from the control endpoint stream. This is used to
- * discard unused bytes in the stream from the host, including the memory program block suffix.
- *
- * \param[in] NumberOfBytes Number of bytes to discard from the host from the control endpoint
- */
-static void DiscardFillerBytes(uint8_t NumberOfBytes)
-{
- while (NumberOfBytes--)
- {
- if (!(Endpoint_BytesInEndpoint()))
- {
- Endpoint_ClearOUT();
-
- /* Wait until next data packet received */
- while (!(Endpoint_IsOUTReceived()))
- {
- if (USB_DeviceState == DEVICE_STATE_Unattached)
- return;
- }
- }
- else
- {
- Endpoint_Discard_Byte();
- }
- }
-}
-
-/** Routine to process an issued command from the host, via a DFU_DNLOAD request wrapper. This routine ensures
- * that the command is allowed based on the current secure mode flag value, and passes the command off to the
- * appropriate handler function.
- */
-static void ProcessBootloaderCommand(void)
-{
- /* Check if device is in secure mode */
-// if (IsSecure)
-// {
-// /* Don't process command unless it is a READ or chip erase command */
-// if (!(((SentCommand.Command == COMMAND_WRITE) &&
-// IS_TWOBYTE_COMMAND(SentCommand.Data, 0x00, 0xFF)) ||
-// (SentCommand.Command == COMMAND_READ)))
-// {
-// /* Set the state and status variables to indicate the error */
-// DFU_State = dfuERROR;
-// DFU_Status = errWRITE;
-//
-// /* Stall command */
-// Endpoint_StallTransaction();
-//
-// /* Don't process the command */
-// return;
-// }
-// }
-
- /* Dispatch the required command processing routine based on the command type */
- switch (SentCommand.Command)
- {
- case COMMAND_PROG_START:
- ProcessMemProgCommand();
- break;
- case COMMAND_DISP_DATA:
- ProcessMemReadCommand();
- break;
- case COMMAND_WRITE:
- ProcessWriteCommand();
- break;
- case COMMAND_READ:
- ProcessReadCommand();
- break;
- case COMMAND_CHANGE_BASE_ADDR:
- if (IS_TWOBYTE_COMMAND(SentCommand.Data, 0x03, 0x00)) // Set 64KB flash page command
- Flash64KBPage = SentCommand.Data[2];
- break;
- }
-}
-
-/** Routine to concatenate the given pair of 16-bit memory start and end addresses from the host, and store them
- * in the StartAddr and EndAddr global variables.
- */
-static void LoadStartEndAddresses(void)
-{
- union
- {
- uint8_t Bytes[2];
- uint16_t Word;
- } Address[2] = {{.Bytes = {SentCommand.Data[2], SentCommand.Data[1]}},
- {.Bytes = {SentCommand.Data[4], SentCommand.Data[3]}}};
-
- /* Load in the start and ending read addresses from the sent data packet */
- StartAddr = Address[0].Word;
- EndAddr = Address[1].Word;
-}
-
-/** Handler for a Memory Program command issued by the host. This routine handles the preparations needed
- * to write subsequent data from the host into the specified memory.
- */
-static void ProcessMemProgCommand(void)
-{
- if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x00) || // Write FLASH command
- IS_ONEBYTE_COMMAND(SentCommand.Data, 0x01)) // Write EEPROM command
- {
- /* Load in the start and ending read addresses */
- LoadStartEndAddresses();
-
- /* If FLASH is being written to, we need to pre-erase the first page to write to */
- if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x00))
- {
- union
- {
- uint16_t Words[2];
- uint32_t Long;
- } CurrFlashAddress = {.Words = {StartAddr, Flash64KBPage}};
-
- /* Erase the current page's temp buffer */
- boot_page_erase(CurrFlashAddress.Long);
- boot_spm_busy_wait();
- }
-
- /* Set the state so that the next DNLOAD requests reads in the firmware */
- DFU_State = dfuDNLOAD_IDLE;
- }
-}
-
-/** Handler for a Memory Read command issued by the host. This routine handles the preparations needed
- * to read subsequent data from the specified memory out to the host, as well as implementing the memory
- * blank check command.
- */
-static void ProcessMemReadCommand(void)
-{
- if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x00) || // Read FLASH command
- IS_ONEBYTE_COMMAND(SentCommand.Data, 0x02)) // Read EEPROM command
- {
- /* Load in the start and ending read addresses */
- LoadStartEndAddresses();
-
- /* Set the state so that the next UPLOAD requests read out the firmware */
- DFU_State = dfuUPLOAD_IDLE;
- }
- else if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x01)) // Blank check FLASH command
- {
- uint32_t CurrFlashAddress = 0;
-
- while (CurrFlashAddress < BOOT_START_ADDR)
- {
- /* Check if the current byte is not blank */
- #if (FLASHEND > 0xFFFF)
- if (pgm_read_byte_far(CurrFlashAddress) != 0xFF)
- #else
- if (pgm_read_byte(CurrFlashAddress) != 0xFF)
- #endif
- {
- /* Save the location of the first non-blank byte for response back to the host */
- Flash64KBPage = (CurrFlashAddress >> 16);
- StartAddr = CurrFlashAddress;
-
- /* Set state and status variables to the appropriate error values */
- DFU_State = dfuERROR;
- DFU_Status = errCHECK_ERASED;
-
- break;
- }
-
- CurrFlashAddress++;
- }
- }
-}
-
-/** Handler for a Data Write command issued by the host. This routine handles non-programming commands such as
- * bootloader exit (both via software jumps and hardware watchdog resets) and flash memory erasure.
- */
-static void ProcessWriteCommand(void)
-{
- if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x03)) // Start application
- {
- /* Indicate that the bootloader is terminating */
- WaitForExit = true;
-
- /* Check if data supplied for the Start Program command - no data executes the program */
- if (SentCommand.DataSize)
- {
- if (SentCommand.Data[1] == 0x01) // Start via jump
- {
- union
- {
- uint8_t Bytes[2];
- AppPtr_t FuncPtr;
- } Address = {.Bytes = {SentCommand.Data[4], SentCommand.Data[3]}};
-
- /* Load in the jump address into the application start address pointer */
- AppStartPtr = Address.FuncPtr;
- }
- }
- else
- {
- if (SentCommand.Data[1] == 0x00) // Start via watchdog
- {
- /* Start the watchdog to reset the AVR once the communications are finalized */
- wdt_enable(WDTO_250MS);
- }
- else // Start via jump
- {
- /* Set the flag to terminate the bootloader at next opportunity */
- RunBootloader = false;
- }
- }
- }
- else if (IS_TWOBYTE_COMMAND(SentCommand.Data, 0x00, 0xFF)) // Erase flash
- {
- uint32_t CurrFlashAddress = 0;
-
- /* Clear the application section of flash */
- while (CurrFlashAddress < BOOT_START_ADDR)
- {
- boot_page_erase(CurrFlashAddress);
- boot_spm_busy_wait();
- boot_page_write(CurrFlashAddress);
- boot_spm_busy_wait();
-
- CurrFlashAddress += SPM_PAGESIZE;
- }
-
- /* Re-enable the RWW section of flash as writing to the flash locks it out */
- boot_rww_enable();
-
- /* Memory has been erased, reset the security bit so that programming/reading is allowed */
-// IsSecure = false;
- }
-}
-
-/** Handler for a Data Read command issued by the host. This routine handles bootloader information retrieval
- * commands such as device signature and bootloader version retrieval.
- */
-static void ProcessReadCommand(void)
-{
- const uint8_t BootloaderInfo[3] = {BOOTLOADER_VERSION, BOOTLOADER_ID_BYTE1, BOOTLOADER_ID_BYTE2};
- const uint8_t SignatureInfo[3] = {AVR_SIGNATURE_1, AVR_SIGNATURE_2, AVR_SIGNATURE_3};
-
- uint8_t DataIndexToRead = SentCommand.Data[1];
-
- if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x00)) // Read bootloader info
- ResponseByte = BootloaderInfo[DataIndexToRead];
- else if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x01)) // Read signature byte
- ResponseByte = SignatureInfo[DataIndexToRead - 0x30];
-}
|