1 files changed, 118 insertions, 0 deletions
diff --git a/cores/arduino/HardwareSerial_private.h b/cores/arduino/HardwareSerial_private.h
new file mode 100644
index 0000000..915d7a1
--- /dev/null
+++ b/cores/arduino/HardwareSerial_private.h
@@ -0,0 +1,118 @@
+/*
+  HardwareSerial_private.h - Hardware serial library for Wiring
+  Copyright (c) 2006 Nicholas Zambetti.  All right reserved.
+
+  This library is free software; you can redistribute it and/or
+  modify it under the terms of the GNU Lesser General Public
+  License as published by the Free Software Foundation; either
+  version 2.1 of the License, or (at your option) any later version.
+
+  This library is distributed in the hope that it will be useful,
+  but WITHOUT ANY WARRANTY; without even the implied warranty of
+  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+  Lesser General Public License for more details.
+
+  You should have received a copy of the GNU Lesser General Public
+  License along with this library; if not, write to the Free Software
+  Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+
+  Modified 23 November 2006 by David A. Mellis
+  Modified 28 September 2010 by Mark Sproul
+  Modified 14 August 2012 by Alarus
+*/
+
+#include "wiring_private.h"
+
+// this next line disables the entire HardwareSerial.cpp, 
+// this is so I can support Attiny series and any other chip without a uart
+#if defined(HAVE_HWSERIAL0) || defined(HAVE_HWSERIAL1) || defined(HAVE_HWSERIAL2) || defined(HAVE_HWSERIAL3)
+
+// Ensure that the various bit positions we use are available with a 0
+// postfix, so we can always use the values for UART0 for all UARTs. The
+// alternative, passing the various values for each UART to the
+// HardwareSerial constructor also works, but makes the code bigger and
+// slower.
+#if !defined(TXC0)
+#if defined(TXC)
+// On ATmega8, the uart and its bits are not numbered, so there is no TXC0 etc.
+#define TXC0 TXC
+#define RXEN0 RXEN
+#define TXEN0 TXEN
+#define RXCIE0 RXCIE
+#define UDRIE0 UDRIE
+#define U2X0 U2X
+#define UPE0 UPE
+#define UDRE0 UDRE
+#elif defined(TXC1)
+// Some devices have uart1 but no uart0
+#define TXC0 TXC1
+#define RXEN0 RXEN1
+#define TXEN0 TXEN1
+#define RXCIE0 RXCIE1
+#define UDRIE0 UDRIE1
+#define U2X0 U2X1
+#define UPE0 UPE1
+#define UDRE0 UDRE1
+#else
+#error No UART found in HardwareSerial.cpp
+#endif
+#endif // !defined TXC0
+
+// Check at compiletime that it is really ok to use the bit positions of
+// UART0 for the other UARTs as well, in case these values ever get
+// changed for future hardware.
+#if defined(TXC1) && (TXC1 != TXC0 || RXEN1 != RXEN0 || RXCIE1 != RXCIE0 || \
+		      UDRIE1 != UDRIE0 || U2X1 != U2X0 || UPE1 != UPE0 || \
+		      UDRE1 != UDRE0)
+#error "Not all bit positions for UART1 are the same as for UART0"
+#endif
+#if defined(TXC2) && (TXC2 != TXC0 || RXEN2 != RXEN0 || RXCIE2 != RXCIE0 || \
+		      UDRIE2 != UDRIE0 || U2X2 != U2X0 || UPE2 != UPE0 || \
+		      UDRE2 != UDRE0)
+#error "Not all bit positions for UART2 are the same as for UART0"
+#endif
+#if defined(TXC3) && (TXC3 != TXC0 || RXEN3 != RXEN0 || RXCIE3 != RXCIE0 || \
+		      UDRIE3 != UDRIE0 || U3X3 != U3X0 || UPE3 != UPE0 || \
+		      UDRE3 != UDRE0)
+#error "Not all bit positions for UART3 are the same as for UART0"
+#endif
+
+// Constructors ////////////////////////////////////////////////////////////////
+
+HardwareSerial::HardwareSerial(
+  volatile uint8_t *ubrrh, volatile uint8_t *ubrrl,
+  volatile uint8_t *ucsra, volatile uint8_t *ucsrb,
+  volatile uint8_t *ucsrc, volatile uint8_t *udr) :
+    _ubrrh(ubrrh), _ubrrl(ubrrl),
+    _ucsra(ucsra), _ucsrb(ucsrb), _ucsrc(ucsrc),
+    _udr(udr),
+    _rx_buffer_head(0), _rx_buffer_tail(0),
+    _tx_buffer_head(0), _tx_buffer_tail(0)
+{
+}
+
+// Actual interrupt handlers //////////////////////////////////////////////////////////////
+
+void HardwareSerial::_rx_complete_irq(void)
+{
+  if (bit_is_clear(*_ucsra, UPE0)) {
+    // No Parity error, read byte and store it in the buffer if there is
+    // room
+    unsigned char c = *_udr;
+    int i = (unsigned int)(_rx_buffer_head + 1) % SERIAL_BUFFER_SIZE;
+
+    // if we should be storing the received character into the location
+    // just before the tail (meaning that the head would advance to the
+    // current location of the tail), we're about to overflow the buffer
+    // and so we don't write the character or advance the head.
+    if (i != _rx_buffer_tail) {
+      _rx_buffer[_rx_buffer_head] = c;
+      _rx_buffer_head = i;
+    }
+  } else {
+    // Parity error, read byte but discard it
+    *_udr;
+  };
+}
+
+#endif // whole file