16 files changed, 5128 insertions, 0 deletions
diff --git a/bootloaders/atmega/ATmegaBOOT_168.c b/bootloaders/atmega/ATmegaBOOT_168.c
new file mode 100755
index 0000000..2b9fefa
--- /dev/null
+++ b/bootloaders/atmega/ATmegaBOOT_168.c
@@ -0,0 +1,1054 @@
+/**********************************************************/
+/* Serial Bootloader for Atmel megaAVR Controllers        */
+/*                                                        */
+/* tested with ATmega8, ATmega128 and ATmega168           */
+/* should work with other mega's, see code for details    */
+/*                                                        */
+/* ATmegaBOOT.c                                           */
+/*                                                        */
+/*                                                        */
+/* 20090308: integrated Mega changes into main bootloader */
+/*           source by D. Mellis                          */
+/* 20080930: hacked for Arduino Mega (with the 1280       */
+/*           processor, backwards compatible)             */
+/*           by D. Cuartielles                            */
+/* 20070626: hacked for Arduino Diecimila (which auto-    */
+/*           resets when a USB connection is made to it)  */
+/*           by D. Mellis                                 */
+/* 20060802: hacked for Arduino by D. Cuartielles         */
+/*           based on a previous hack by D. Mellis        */
+/*           and D. Cuartielles                           */
+/*                                                        */
+/* Monitor and debug functions were added to the original */
+/* code by Dr. Erik Lins, chip45.com. (See below)         */
+/*                                                        */
+/* Thanks to Karl Pitrich for fixing a bootloader pin     */
+/* problem and more informative LED blinking!             */
+/*                                                        */
+/* For the latest version see:                            */
+/* http://www.chip45.com/                                 */
+/*                                                        */
+/* ------------------------------------------------------ */
+/*                                                        */
+/* based on stk500boot.c                                  */
+/* Copyright (c) 2003, Jason P. Kyle                      */
+/* All rights reserved.                                   */
+/* see avr1.org for original file and information         */
+/*                                                        */
+/* This program is free software; you can redistribute it */
+/* and/or modify it under the terms of the GNU General    */
+/* Public License as published by the Free Software       */
+/* Foundation; either version 2 of the License, or        */
+/* (at your option) any later version.                    */
+/*                                                        */
+/* This program is distributed in the hope that it will   */
+/* be useful, but WITHOUT ANY WARRANTY; without even the  */
+/* implied warranty of MERCHANTABILITY or FITNESS FOR A   */
+/* PARTICULAR PURPOSE.  See the GNU General Public        */
+/* License for more details.                              */
+/*                                                        */
+/* You should have received a copy of the GNU General     */
+/* Public License along with this program; if not, write  */
+/* to the Free Software Foundation, Inc.,                 */
+/* 59 Temple Place, Suite 330, Boston, MA  02111-1307 USA */
+/*                                                        */
+/* Licence can be viewed at                               */
+/* http://www.fsf.org/licenses/gpl.txt                    */
+/*                                                        */
+/* Target = Atmel AVR m128,m64,m32,m16,m8,m162,m163,m169, */
+/* m8515,m8535. ATmega161 has a very small boot block so  */
+/* isn't supported.                                       */
+/*                                                        */
+/* Tested with m168                                       */
+/**********************************************************/
+
+/* $Id$ */
+
+
+/* some includes */
+#include <inttypes.h>
+#include <avr/io.h>
+#include <avr/pgmspace.h>
+#include <avr/interrupt.h>
+#include <avr/wdt.h>
+#include <util/delay.h>
+
+/* the current avr-libc eeprom functions do not support the ATmega168 */
+/* own eeprom write/read functions are used instead */
+#if !defined(__AVR_ATmega168__) || !defined(__AVR_ATmega328P__)
+#include <avr/eeprom.h>
+#endif
+
+/* Use the F_CPU defined in Makefile */
+
+/* 20060803: hacked by DojoCorp */
+/* 20070626: hacked by David A. Mellis to decrease waiting time for auto-reset */
+/* set the waiting time for the bootloader */
+/* get this from the Makefile instead */
+/* #define MAX_TIME_COUNT (F_CPU>>4) */
+
+/* 20070707: hacked by David A. Mellis - after this many errors give up and launch application */
+#define MAX_ERROR_COUNT 5
+
+/* set the UART baud rate */
+/* 20060803: hacked by DojoCorp */
+//#define BAUD_RATE   115200
+#ifndef BAUD_RATE
+#define BAUD_RATE   19200
+#endif
+
+
+/* SW_MAJOR and MINOR needs to be updated from time to time to avoid warning message from AVR Studio */
+/* never allow AVR Studio to do an update !!!! */
+#define HW_VER	 0x02
+#define SW_MAJOR 0x01
+#define SW_MINOR 0x10
+
+
+/* Adjust to suit whatever pin your hardware uses to enter the bootloader */
+/* ATmega128 has two UARTS so two pins are used to enter bootloader and select UART */
+/* ATmega1280 has four UARTS, but for Arduino Mega, we will only use RXD0 to get code */
+/* BL0... means UART0, BL1... means UART1 */
+#ifdef __AVR_ATmega128__
+#define BL_DDR  DDRF
+#define BL_PORT PORTF
+#define BL_PIN  PINF
+#define BL0     PINF7
+#define BL1     PINF6
+#elif defined __AVR_ATmega1280__ 
+/* we just don't do anything for the MEGA and enter bootloader on reset anyway*/
+#else
+/* other ATmegas have only one UART, so only one pin is defined to enter bootloader */
+#define BL_DDR  DDRD
+#define BL_PORT PORTD
+#define BL_PIN  PIND
+#define BL      PIND6
+#endif
+
+
+/* onboard LED is used to indicate, that the bootloader was entered (3x flashing) */
+/* if monitor functions are included, LED goes on after monitor was entered */
+#if defined __AVR_ATmega128__ || defined __AVR_ATmega1280__
+/* Onboard LED is connected to pin PB7 (e.g. Crumb128, PROBOmega128, Savvy128, Arduino Mega) */
+#define LED_DDR  DDRB
+#define LED_PORT PORTB
+#define LED_PIN  PINB
+#define LED      PINB7
+#else
+/* Onboard LED is connected to pin PB5 in Arduino NG, Diecimila, and Duomilanuove */ 
+/* other boards like e.g. Crumb8, Crumb168 are using PB2 */
+#define LED_DDR  DDRB
+#define LED_PORT PORTB
+#define LED_PIN  PINB
+#define LED      PINB5
+#endif
+
+
+/* monitor functions will only be compiled when using ATmega128, due to bootblock size constraints */
+#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
+#define MONITOR 1
+#endif
+
+
+/* define various device id's */
+/* manufacturer byte is always the same */
+#define SIG1	0x1E	// Yep, Atmel is the only manufacturer of AVR micros.  Single source :(
+
+#if defined __AVR_ATmega1280__
+#define SIG2	0x97
+#define SIG3	0x03
+#define PAGE_SIZE	0x80U	//128 words
+
+#elif defined __AVR_ATmega1281__
+#define SIG2	0x97
+#define SIG3	0x04
+#define PAGE_SIZE	0x80U	//128 words
+
+#elif defined __AVR_ATmega128__
+#define SIG2	0x97
+#define SIG3	0x02
+#define PAGE_SIZE	0x80U	//128 words
+
+#elif defined __AVR_ATmega64__
+#define SIG2	0x96
+#define SIG3	0x02
+#define PAGE_SIZE	0x80U	//128 words
+
+#elif defined __AVR_ATmega32__
+#define SIG2	0x95
+#define SIG3	0x02
+#define PAGE_SIZE	0x40U	//64 words
+
+#elif defined __AVR_ATmega16__
+#define SIG2	0x94
+#define SIG3	0x03
+#define PAGE_SIZE	0x40U	//64 words
+
+#elif defined __AVR_ATmega8__
+#define SIG2	0x93
+#define SIG3	0x07
+#define PAGE_SIZE	0x20U	//32 words
+
+#elif defined __AVR_ATmega88__
+#define SIG2	0x93
+#define SIG3	0x0a
+#define PAGE_SIZE	0x20U	//32 words
+
+#elif defined __AVR_ATmega168__
+#define SIG2	0x94
+#define SIG3	0x06
+#define PAGE_SIZE	0x40U	//64 words
+
+#elif defined __AVR_ATmega328P__
+#define SIG2	0x95
+#define SIG3	0x0F
+#define PAGE_SIZE	0x40U	//64 words
+
+#elif defined __AVR_ATmega162__
+#define SIG2	0x94
+#define SIG3	0x04
+#define PAGE_SIZE	0x40U	//64 words
+
+#elif defined __AVR_ATmega163__
+#define SIG2	0x94
+#define SIG3	0x02
+#define PAGE_SIZE	0x40U	//64 words
+
+#elif defined __AVR_ATmega169__
+#define SIG2	0x94
+#define SIG3	0x05
+#define PAGE_SIZE	0x40U	//64 words
+
+#elif defined __AVR_ATmega8515__
+#define SIG2	0x93
+#define SIG3	0x06
+#define PAGE_SIZE	0x20U	//32 words
+
+#elif defined __AVR_ATmega8535__
+#define SIG2	0x93
+#define SIG3	0x08
+#define PAGE_SIZE	0x20U	//32 words
+#endif
+
+
+/* function prototypes */
+void putch(char);
+char getch(void);
+void getNch(uint8_t);
+void byte_response(uint8_t);
+void nothing_response(void);
+char gethex(void);
+void puthex(char);
+void flash_led(uint8_t);
+
+/* some variables */
+union address_union {
+	uint16_t word;
+	uint8_t  byte[2];
+} address;
+
+union length_union {
+	uint16_t word;
+	uint8_t  byte[2];
+} length;
+
+struct flags_struct {
+	unsigned eeprom : 1;
+	unsigned rampz  : 1;
+} flags;
+
+uint8_t buff[256];
+uint8_t address_high;
+
+uint8_t pagesz=0x80;
+
+uint8_t i;
+uint8_t bootuart = 0;
+
+uint8_t error_count = 0;
+
+void (*app_start)(void) = 0x0000;
+
+
+/* main program starts here */
+int main(void)
+{
+	uint8_t ch,ch2;
+	uint16_t w;
+
+#ifdef WATCHDOG_MODS
+	ch = MCUSR;
+	MCUSR = 0;
+
+	WDTCSR |= _BV(WDCE) | _BV(WDE);
+	WDTCSR = 0;
+
+	// Check if the WDT was used to reset, in which case we dont bootload and skip straight to the code. woot.
+	if (! (ch &  _BV(EXTRF))) // if its a not an external reset...
+		app_start();  // skip bootloader
+#else
+	asm volatile("nop\n\t");
+#endif
+
+	/* set pin direction for bootloader pin and enable pullup */
+	/* for ATmega128, two pins need to be initialized */
+#ifdef __AVR_ATmega128__
+	BL_DDR &= ~_BV(BL0);
+	BL_DDR &= ~_BV(BL1);
+	BL_PORT |= _BV(BL0);
+	BL_PORT |= _BV(BL1);
+#else
+	/* We run the bootloader regardless of the state of this pin.  Thus, don't
+	put it in a different state than the other pins.  --DAM, 070709
+	This also applies to Arduino Mega -- DC, 080930
+	BL_DDR &= ~_BV(BL);
+	BL_PORT |= _BV(BL);
+	*/
+#endif
+
+
+#ifdef __AVR_ATmega128__
+	/* check which UART should be used for booting */
+	if(bit_is_clear(BL_PIN, BL0)) {
+		bootuart = 1;
+	}
+	else if(bit_is_clear(BL_PIN, BL1)) {
+		bootuart = 2;
+	}
+#endif
+
+#if defined __AVR_ATmega1280__
+	/* the mega1280 chip has four serial ports ... we could eventually use any of them, or not? */
+	/* however, we don't wanna confuse people, to avoid making a mess, we will stick to RXD0, TXD0 */
+	bootuart = 1;
+#endif
+
+	/* check if flash is programmed already, if not start bootloader anyway */
+	if(pgm_read_byte_near(0x0000) != 0xFF) {
+
+#ifdef __AVR_ATmega128__
+	/* no UART was selected, start application */
+	if(!bootuart) {
+		app_start();
+	}
+#else
+	/* check if bootloader pin is set low */
+	/* we don't start this part neither for the m8, nor m168 */
+	//if(bit_is_set(BL_PIN, BL)) {
+	//      app_start();
+	//    }
+#endif
+	}
+
+#ifdef __AVR_ATmega128__    
+	/* no bootuart was selected, default to uart 0 */
+	if(!bootuart) {
+		bootuart = 1;
+	}
+#endif
+
+
+	/* initialize UART(s) depending on CPU defined */
+#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
+	if(bootuart == 1) {
+		UBRR0L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
+		UBRR0H = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
+		UCSR0A = 0x00;
+		UCSR0C = 0x06;
+		UCSR0B = _BV(TXEN0)|_BV(RXEN0);
+	}
+	if(bootuart == 2) {
+		UBRR1L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
+		UBRR1H = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
+		UCSR1A = 0x00;
+		UCSR1C = 0x06;
+		UCSR1B = _BV(TXEN1)|_BV(RXEN1);
+	}
+#elif defined __AVR_ATmega163__
+	UBRR = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
+	UBRRHI = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
+	UCSRA = 0x00;
+	UCSRB = _BV(TXEN)|_BV(RXEN);	
+#elif defined(__AVR_ATmega168__) || defined(__AVR_ATmega328P__)
+
+#ifdef DOUBLE_SPEED
+	UCSR0A = (1<<U2X0); //Double speed mode USART0
+	UBRR0L = (uint8_t)(F_CPU/(BAUD_RATE*8L)-1);
+	UBRR0H = (F_CPU/(BAUD_RATE*8L)-1) >> 8;
+#else
+	UBRR0L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
+	UBRR0H = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
+#endif
+
+	UCSR0B = (1<<RXEN0) | (1<<TXEN0);
+	UCSR0C = (1<<UCSZ00) | (1<<UCSZ01);
+
+	/* Enable internal pull-up resistor on pin D0 (RX), in order
+	to supress line noise that prevents the bootloader from
+	timing out (DAM: 20070509) */
+	DDRD &= ~_BV(PIND0);
+	PORTD |= _BV(PIND0);
+#elif defined __AVR_ATmega8__
+	/* m8 */
+	UBRRH = (((F_CPU/BAUD_RATE)/16)-1)>>8; 	// set baud rate
+	UBRRL = (((F_CPU/BAUD_RATE)/16)-1);
+	UCSRB = (1<<RXEN)|(1<<TXEN);  // enable Rx & Tx
+	UCSRC = (1<<URSEL)|(1<<UCSZ1)|(1<<UCSZ0);  // config USART; 8N1
+#else
+	/* m16,m32,m169,m8515,m8535 */
+	UBRRL = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
+	UBRRH = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
+	UCSRA = 0x00;
+	UCSRC = 0x06;
+	UCSRB = _BV(TXEN)|_BV(RXEN);
+#endif
+
+#if defined __AVR_ATmega1280__
+	/* Enable internal pull-up resistor on pin D0 (RX), in order
+	to supress line noise that prevents the bootloader from
+	timing out (DAM: 20070509) */
+	/* feature added to the Arduino Mega --DC: 080930 */
+	DDRE &= ~_BV(PINE0);
+	PORTE |= _BV(PINE0);
+#endif
+
+
+	/* set LED pin as output */
+	LED_DDR |= _BV(LED);
+
+
+	/* flash onboard LED to signal entering of bootloader */
+#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
+	// 4x for UART0, 5x for UART1
+	flash_led(NUM_LED_FLASHES + bootuart);
+#else
+	flash_led(NUM_LED_FLASHES);
+#endif
+
+	/* 20050803: by DojoCorp, this is one of the parts provoking the
+		 system to stop listening, cancelled from the original */
+	//putch('\0');
+
+	/* forever loop */
+	for (;;) {
+
+	/* get character from UART */
+	ch = getch();
+
+	/* A bunch of if...else if... gives smaller code than switch...case ! */
+
+	/* Hello is anyone home ? */ 
+	if(ch=='0') {
+		nothing_response();
+	}
+
+
+	/* Request programmer ID */
+	/* Not using PROGMEM string due to boot block in m128 being beyond 64kB boundry  */
+	/* Would need to selectively manipulate RAMPZ, and it's only 9 characters anyway so who cares.  */
+	else if(ch=='1') {
+		if (getch() == ' ') {
+			putch(0x14);
+			putch('A');
+			putch('V');
+			putch('R');
+			putch(' ');
+			putch('I');
+			putch('S');
+			putch('P');
+			putch(0x10);
+		} else {
+			if (++error_count == MAX_ERROR_COUNT)
+				app_start();
+		}
+	}
+
+
+	/* AVR ISP/STK500 board commands  DON'T CARE so default nothing_response */
+	else if(ch=='@') {
+		ch2 = getch();
+		if (ch2>0x85) getch();
+		nothing_response();
+	}
+
+
+	/* AVR ISP/STK500 board requests */
+	else if(ch=='A') {
+		ch2 = getch();
+		if(ch2==0x80) byte_response(HW_VER);		// Hardware version
+		else if(ch2==0x81) byte_response(SW_MAJOR);	// Software major version
+		else if(ch2==0x82) byte_response(SW_MINOR);	// Software minor version
+		else if(ch2==0x98) byte_response(0x03);		// Unknown but seems to be required by avr studio 3.56
+		else byte_response(0x00);				// Covers various unnecessary responses we don't care about
+	}
+
+
+	/* Device Parameters  DON'T CARE, DEVICE IS FIXED  */
+	else if(ch=='B') {
+		getNch(20);
+		nothing_response();
+	}
+
+
+	/* Parallel programming stuff  DON'T CARE  */
+	else if(ch=='E') {
+		getNch(5);
+		nothing_response();
+	}
+
+
+	/* P: Enter programming mode  */
+	/* R: Erase device, don't care as we will erase one page at a time anyway.  */
+	else if(ch=='P' || ch=='R') {
+		nothing_response();
+	}
+
+
+	/* Leave programming mode  */
+	else if(ch=='Q') {
+		nothing_response();
+#ifdef WATCHDOG_MODS
+		// autoreset via watchdog (sneaky!)
+		WDTCSR = _BV(WDE);
+		while (1); // 16 ms
+#endif
+	}
+
+
+	/* Set address, little endian. EEPROM in bytes, FLASH in words  */
+	/* Perhaps extra address bytes may be added in future to support > 128kB FLASH.  */
+	/* This might explain why little endian was used here, big endian used everywhere else.  */
+	else if(ch=='U') {
+		address.byte[0] = getch();
+		address.byte[1] = getch();
+		nothing_response();
+	}
+
+
+	/* Universal SPI programming command, disabled.  Would be used for fuses and lock bits.  */
+	else if(ch=='V') {
+		if (getch() == 0x30) {
+			getch();
+			ch = getch();
+			getch();
+			if (ch == 0) {
+				byte_response(SIG1);
+			} else if (ch == 1) {
+				byte_response(SIG2); 
+			} else {
+				byte_response(SIG3);
+			} 
+		} else {
+			getNch(3);
+			byte_response(0x00);
+		}
+	}
+
+
+	/* Write memory, length is big endian and is in bytes  */
+	else if(ch=='d') {
+		length.byte[1] = getch();
+		length.byte[0] = getch();
+		flags.eeprom = 0;
+		if (getch() == 'E') flags.eeprom = 1;
+		for (w=0;w<length.word;w++) {
+			buff[w] = getch();	                        // Store data in buffer, can't keep up with serial data stream whilst programming pages
+		}
+		if (getch() == ' ') {
+			if (flags.eeprom) {		                //Write to EEPROM one byte at a time
+				address.word <<= 1;
+				for(w=0;w<length.word;w++) {
+#if defined(__AVR_ATmega168__)  || defined(__AVR_ATmega328P__)
+					while(EECR & (1<<EEPE));
+					EEAR = (uint16_t)(void *)address.word;
+					EEDR = buff[w];
+					EECR |= (1<<EEMPE);
+					EECR |= (1<<EEPE);
+#else
+					eeprom_write_byte((void *)address.word,buff[w]);
+#endif
+					address.word++;
+				}			
+			}
+			else {					        //Write to FLASH one page at a time
+				if (address.byte[1]>127) address_high = 0x01;	//Only possible with m128, m256 will need 3rd address byte. FIXME
+				else address_high = 0x00;
+#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__) || defined(__AVR_ATmega1281__)
+				RAMPZ = address_high;
+#endif
+				address.word = address.word << 1;	        //address * 2 -> byte location
+				/* if ((length.byte[0] & 0x01) == 0x01) length.word++;	//Even up an odd number of bytes */
+				if ((length.byte[0] & 0x01)) length.word++;	//Even up an odd number of bytes
+				cli();					//Disable interrupts, just to be sure
+#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega1281__)
+				while(bit_is_set(EECR,EEPE));			//Wait for previous EEPROM writes to complete
+#else
+				while(bit_is_set(EECR,EEWE));			//Wait for previous EEPROM writes to complete
+#endif
+				asm volatile(
+					 "clr	r17		\n\t"	//page_word_count
+					 "lds	r30,address	\n\t"	//Address of FLASH location (in bytes)
+					 "lds	r31,address+1	\n\t"
+					 "ldi	r28,lo8(buff)	\n\t"	//Start of buffer array in RAM
+					 "ldi	r29,hi8(buff)	\n\t"
+					 "lds	r24,length	\n\t"	//Length of data to be written (in bytes)
+					 "lds	r25,length+1	\n\t"
+					 "length_loop:		\n\t"	//Main loop, repeat for number of words in block							 							 
+					 "cpi	r17,0x00	\n\t"	//If page_word_count=0 then erase page
+					 "brne	no_page_erase	\n\t"						 
+					 "wait_spm1:		\n\t"
+					 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+					 "andi	r16,1           \n\t"
+					 "cpi	r16,1           \n\t"
+					 "breq	wait_spm1       \n\t"
+					 "ldi	r16,0x03	\n\t"	//Erase page pointed to by Z
+					 "sts	%0,r16		\n\t"
+					 "spm			\n\t"							 
+#ifdef __AVR_ATmega163__
+					 ".word 0xFFFF		\n\t"
+					 "nop			\n\t"
+#endif
+					 "wait_spm2:		\n\t"
+					 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+					 "andi	r16,1           \n\t"
+					 "cpi	r16,1           \n\t"
+					 "breq	wait_spm2       \n\t"									 
+
+					 "ldi	r16,0x11	\n\t"	//Re-enable RWW section
+					 "sts	%0,r16		\n\t"						 			 
+					 "spm			\n\t"
+#ifdef __AVR_ATmega163__
+					 ".word 0xFFFF		\n\t"
+					 "nop			\n\t"
+#endif
+					 "no_page_erase:		\n\t"							 
+					 "ld	r0,Y+		\n\t"	//Write 2 bytes into page buffer
+					 "ld	r1,Y+		\n\t"							 
+								 
+					 "wait_spm3:		\n\t"
+					 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+					 "andi	r16,1           \n\t"
+					 "cpi	r16,1           \n\t"
+					 "breq	wait_spm3       \n\t"
+					 "ldi	r16,0x01	\n\t"	//Load r0,r1 into FLASH page buffer
+					 "sts	%0,r16		\n\t"
+					 "spm			\n\t"
+								 
+					 "inc	r17		\n\t"	//page_word_count++
+					 "cpi r17,%1	        \n\t"
+					 "brlo	same_page	\n\t"	//Still same page in FLASH
+					 "write_page:		\n\t"
+					 "clr	r17		\n\t"	//New page, write current one first
+					 "wait_spm4:		\n\t"
+					 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+					 "andi	r16,1           \n\t"
+					 "cpi	r16,1           \n\t"
+					 "breq	wait_spm4       \n\t"
+#ifdef __AVR_ATmega163__
+					 "andi	r30,0x80	\n\t"	// m163 requires Z6:Z1 to be zero during page write
+#endif							 							 
+					 "ldi	r16,0x05	\n\t"	//Write page pointed to by Z
+					 "sts	%0,r16		\n\t"
+					 "spm			\n\t"
+#ifdef __AVR_ATmega163__
+					 ".word 0xFFFF		\n\t"
+					 "nop			\n\t"
+					 "ori	r30,0x7E	\n\t"	// recover Z6:Z1 state after page write (had to be zero during write)
+#endif
+					 "wait_spm5:		\n\t"
+					 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+					 "andi	r16,1           \n\t"
+					 "cpi	r16,1           \n\t"
+					 "breq	wait_spm5       \n\t"									 
+					 "ldi	r16,0x11	\n\t"	//Re-enable RWW section
+					 "sts	%0,r16		\n\t"						 			 
+					 "spm			\n\t"					 		 
+#ifdef __AVR_ATmega163__
+					 ".word 0xFFFF		\n\t"
+					 "nop			\n\t"
+#endif
+					 "same_page:		\n\t"							 
+					 "adiw	r30,2		\n\t"	//Next word in FLASH
+					 "sbiw	r24,2		\n\t"	//length-2
+					 "breq	final_write	\n\t"	//Finished
+					 "rjmp	length_loop	\n\t"
+					 "final_write:		\n\t"
+					 "cpi	r17,0		\n\t"
+					 "breq	block_done	\n\t"
+					 "adiw	r24,2		\n\t"	//length+2, fool above check on length after short page write
+					 "rjmp	write_page	\n\t"
+					 "block_done:		\n\t"
+					 "clr	__zero_reg__	\n\t"	//restore zero register
+#if defined __AVR_ATmega168__  || __AVR_ATmega328P__ || __AVR_ATmega128__ || __AVR_ATmega1280__ || __AVR_ATmega1281__ 
+					 : "=m" (SPMCSR) : "M" (PAGE_SIZE) : "r0","r16","r17","r24","r25","r28","r29","r30","r31"
+#else
+					 : "=m" (SPMCR) : "M" (PAGE_SIZE) : "r0","r16","r17","r24","r25","r28","r29","r30","r31"
+#endif
+					 );
+				/* Should really add a wait for RWW section to be enabled, don't actually need it since we never */
+				/* exit the bootloader without a power cycle anyhow */
+			}
+			putch(0x14);
+			putch(0x10);
+		} else {
+			if (++error_count == MAX_ERROR_COUNT)
+				app_start();
+		}		
+	}
+
+
+	/* Read memory block mode, length is big endian.  */
+	else if(ch=='t') {
+		length.byte[1] = getch();
+		length.byte[0] = getch();
+#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
+		if (address.word>0x7FFF) flags.rampz = 1;		// No go with m256, FIXME
+		else flags.rampz = 0;
+#endif
+		address.word = address.word << 1;	        // address * 2 -> byte location
+		if (getch() == 'E') flags.eeprom = 1;
+		else flags.eeprom = 0;
+		if (getch() == ' ') {		                // Command terminator
+			putch(0x14);
+			for (w=0;w < length.word;w++) {		        // Can handle odd and even lengths okay
+				if (flags.eeprom) {	                        // Byte access EEPROM read
+#if defined(__AVR_ATmega168__)  || defined(__AVR_ATmega328P__)
+					while(EECR & (1<<EEPE));
+					EEAR = (uint16_t)(void *)address.word;
+					EECR |= (1<<EERE);
+					putch(EEDR);
+#else
+					putch(eeprom_read_byte((void *)address.word));
+#endif
+					address.word++;
+				}
+				else {
+
+					if (!flags.rampz) putch(pgm_read_byte_near(address.word));
+#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
+					else putch(pgm_read_byte_far(address.word + 0x10000));
+					// Hmmmm, yuck  FIXME when m256 arrvies
+#endif
+					address.word++;
+				}
+			}
+			putch(0x10);
+		}
+	}
+
+
+	/* Get device signature bytes  */
+	else if(ch=='u') {
+		if (getch() == ' ') {
+			putch(0x14);
+			putch(SIG1);
+			putch(SIG2);
+			putch(SIG3);
+			putch(0x10);
+		} else {
+			if (++error_count == MAX_ERROR_COUNT)
+				app_start();
+		}
+	}
+
+
+	/* Read oscillator calibration byte */
+	else if(ch=='v') {
+		byte_response(0x00);
+	}
+
+
+#if defined MONITOR 
+
+	/* here come the extended monitor commands by Erik Lins */
+
+	/* check for three times exclamation mark pressed */
+	else if(ch=='!') {
+		ch = getch();
+		if(ch=='!') {
+		ch = getch();
+		if(ch=='!') {
+			PGM_P welcome = "";
+#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
+			uint16_t extaddr;
+#endif
+			uint8_t addrl, addrh;
+
+#ifdef CRUMB128
+			welcome = "ATmegaBOOT / Crumb128 - (C) J.P.Kyle, E.Lins - 050815\n\r";
+#elif defined PROBOMEGA128
+			welcome = "ATmegaBOOT / PROBOmega128 - (C) J.P.Kyle, E.Lins - 050815\n\r";
+#elif defined SAVVY128
+			welcome = "ATmegaBOOT / Savvy128 - (C) J.P.Kyle, E.Lins - 050815\n\r";
+#elif defined __AVR_ATmega1280__ 
+			welcome = "ATmegaBOOT / Arduino Mega - (C) Arduino LLC - 090930\n\r";
+#endif
+
+			/* turn on LED */
+			LED_DDR |= _BV(LED);
+			LED_PORT &= ~_BV(LED);
+
+			/* print a welcome message and command overview */
+			for(i=0; welcome[i] != '\0'; ++i) {
+				putch(welcome[i]);
+			}
+
+			/* test for valid commands */
+			for(;;) {
+				putch('\n');
+				putch('\r');
+				putch(':');
+				putch(' ');
+
+				ch = getch();
+				putch(ch);
+
+				/* toggle LED */
+				if(ch == 't') {
+					if(bit_is_set(LED_PIN,LED)) {
+						LED_PORT &= ~_BV(LED);
+						putch('1');
+					} else {
+						LED_PORT |= _BV(LED);
+						putch('0');
+					}
+				} 
+
+				/* read byte from address */
+				else if(ch == 'r') {
+					ch = getch(); putch(ch);
+					addrh = gethex();
+					addrl = gethex();
+					putch('=');
+					ch = *(uint8_t *)((addrh << 8) + addrl);
+					puthex(ch);
+				}
+
+				/* write a byte to address  */
+				else if(ch == 'w') {
+					ch = getch(); putch(ch);
+					addrh = gethex();
+					addrl = gethex();
+					ch = getch(); putch(ch);
+					ch = gethex();
+					*(uint8_t *)((addrh << 8) + addrl) = ch;
+				}
+
+				/* read from uart and echo back */
+				else if(ch == 'u') {
+					for(;;) {
+						putch(getch());
+					}
+				}
+#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
+				/* external bus loop  */
+				else if(ch == 'b') {
+					putch('b');
+					putch('u');
+					putch('s');
+					MCUCR = 0x80;
+					XMCRA = 0;
+					XMCRB = 0;
+					extaddr = 0x1100;
+					for(;;) {
+						ch = *(volatile uint8_t *)extaddr;
+						if(++extaddr == 0) {
+							extaddr = 0x1100;
+						}
+					}
+				}
+#endif
+
+				else if(ch == 'j') {
+					app_start();
+				}
+
+			} /* end of monitor functions */
+
+		}
+		}
+	}
+	/* end of monitor */
+#endif
+	else if (++error_count == MAX_ERROR_COUNT) {
+		app_start();
+	}
+	} /* end of forever loop */
+
+}
+
+
+char gethexnib(void) {
+	char a;
+	a = getch(); putch(a);
+	if(a >= 'a') {
+		return (a - 'a' + 0x0a);
+	} else if(a >= '0') {
+		return(a - '0');
+	}
+	return a;
+}
+
+
+char gethex(void) {
+	return (gethexnib() << 4) + gethexnib();
+}
+
+
+void puthex(char ch) {
+	char ah;
+
+	ah = ch >> 4;
+	if(ah >= 0x0a) {
+		ah = ah - 0x0a + 'a';
+	} else {
+		ah += '0';
+	}
+	
+	ch &= 0x0f;
+	if(ch >= 0x0a) {
+		ch = ch - 0x0a + 'a';
+	} else {
+		ch += '0';
+	}
+	
+	putch(ah);
+	putch(ch);
+}
+
+
+void putch(char ch)
+{
+#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
+	if(bootuart == 1) {
+		while (!(UCSR0A & _BV(UDRE0)));
+		UDR0 = ch;
+	}
+	else if (bootuart == 2) {
+		while (!(UCSR1A & _BV(UDRE1)));
+		UDR1 = ch;
+	}
+#elif defined(__AVR_ATmega168__)  || defined(__AVR_ATmega328P__)
+	while (!(UCSR0A & _BV(UDRE0)));
+	UDR0 = ch;
+#else
+	/* m8,16,32,169,8515,8535,163 */
+	while (!(UCSRA & _BV(UDRE)));
+	UDR = ch;
+#endif
+}
+
+
+char getch(void)
+{
+#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
+	uint32_t count = 0;
+	if(bootuart == 1) {
+		while(!(UCSR0A & _BV(RXC0))) {
+			/* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/               
+			/* HACKME:: here is a good place to count times*/
+			count++;
+			if (count > MAX_TIME_COUNT)
+				app_start();
+			}
+
+			return UDR0;
+		}
+	else if(bootuart == 2) {
+		while(!(UCSR1A & _BV(RXC1))) {
+			/* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/               
+			/* HACKME:: here is a good place to count times*/
+			count++;
+			if (count > MAX_TIME_COUNT)
+				app_start();
+		}
+
+		return UDR1;
+	}
+	return 0;
+#elif defined(__AVR_ATmega168__)  || defined(__AVR_ATmega328P__)
+	uint32_t count = 0;
+	while(!(UCSR0A & _BV(RXC0))){
+		/* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/               
+		/* HACKME:: here is a good place to count times*/
+		count++;
+		if (count > MAX_TIME_COUNT)
+			app_start();
+	}
+	return UDR0;
+#else
+	/* m8,16,32,169,8515,8535,163 */
+	uint32_t count = 0;
+	while(!(UCSRA & _BV(RXC))){
+		/* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/               
+		/* HACKME:: here is a good place to count times*/
+		count++;
+		if (count > MAX_TIME_COUNT)
+			app_start();
+	}
+	return UDR;
+#endif
+}
+
+
+void getNch(uint8_t count)
+{
+	while(count--) {
+#if defined(__AVR_ATmega128__) || defined(__AVR_ATmega1280__)
+		if(bootuart == 1) {
+			while(!(UCSR0A & _BV(RXC0)));
+			UDR0;
+		} 
+		else if(bootuart == 2) {
+			while(!(UCSR1A & _BV(RXC1)));
+			UDR1;
+		}
+#elif defined(__AVR_ATmega168__)  || defined(__AVR_ATmega328P__)
+		getch();
+#else
+		/* m8,16,32,169,8515,8535,163 */
+		/* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/               
+		//while(!(UCSRA & _BV(RXC)));
+		//UDR;
+		getch(); // need to handle time out
+#endif		
+	}
+}
+
+
+void byte_response(uint8_t val)
+{
+	if (getch() == ' ') {
+		putch(0x14);
+		putch(val);
+		putch(0x10);
+	} else {
+		if (++error_count == MAX_ERROR_COUNT)
+			app_start();
+	}
+}
+
+
+void nothing_response(void)
+{
+	if (getch() == ' ') {
+		putch(0x14);
+		putch(0x10);
+	} else {
+		if (++error_count == MAX_ERROR_COUNT)
+			app_start();
+	}
+}
+
+void flash_led(uint8_t count)
+{
+	while (count--) {
+		LED_PORT |= _BV(LED);
+		_delay_ms(100);
+		LED_PORT &= ~_BV(LED);
+		_delay_ms(100);
+	}
+}
+
+
+/* end of file ATmegaBOOT.c */
diff --git a/bootloaders/atmega/ATmegaBOOT_168_atmega1280.hex b/bootloaders/atmega/ATmegaBOOT_168_atmega1280.hex
new file mode 100644
index 0000000..f16e877
--- /dev/null
+++ b/bootloaders/atmega/ATmegaBOOT_168_atmega1280.hex
@@ -0,0 +1,245 @@
+:020000021000EC
+:10F000000C9472F80C9492F80C9492F80C9492F878
+:10F010000C9492F80C9492F80C9492F80C9492F848
+:10F020000C9492F80C9492F80C9492F80C9492F838
+:10F030000C9492F80C9492F80C9492F80C9492F828
+:10F040000C9492F80C9492F80C9492F80C9492F818
+:10F050000C9492F80C9492F80C9492F80C9492F808
+:10F060000C9492F80C9492F80C9492F80C9492F8F8
+:10F070000C9492F80C9492F80C9492F80C9492F8E8
+:10F080000C9492F80C9492F80C9492F80C9492F8D8
+:10F090000C9492F80C9492F80C9492F80C9492F8C8
+:10F0A0000C9492F80C9492F80C9492F80C9492F8B8
+:10F0B0000C9492F80C9492F80C9492F80C9492F8A8
+:10F0C0000C9492F80C9492F80C9492F80C9492F898
+:10F0D0000C9492F80C9492F80C9492F80C9492F888
+:10F0E0000C9492F811241FBECFEFD1E2DEBFCDBF4A
+:10F0F00012E0A0E0B2E0EEEDFEEF01E00BBF02C0D7
+:10F1000007900D92A833B107D9F71BBE13E0A8E30F
+:10F11000B2E001C01D92A334B107E1F70E9412FAD8
+:10F120000C946DFF0C9400F8982F959595959595F6
+:10F130009595905D8F708A301CF1282F295A809107
+:10F140003802813019F0823071F008958091C0004A
+:10F1500085FFFCCF9093C6008091C00085FFFCCF57
+:10F160002093C60008958091C80085FFFCCF90933E
+:10F17000CE008091C80085FFFCCF2093CE0008957B
+:10F18000282F205DDCCF982F80913802813019F034
+:10F19000823041F008958091C00085FFFCCF9093AC
+:10F1A000C60008958091C80085FFFCCF9093CE00E3
+:10F1B0000895EF92FF920F931F9380913802813050
+:10F1C00069F1823031F080E01F910F91FF90EF9054
+:10F1D0000895EE24FF2487018091C80087FD17C0A1
+:10F1E0000894E11CF11C011D111D81E4E81682E464
+:10F1F000F8068FE0080780E0180770F3E0913A0204
+:10F20000F0913B0209958091C80087FFE9CF80917A
+:10F21000CE001F910F91FF90EF900895EE24FF24F0
+:10F2200087018091C00087FD17C00894E11CF11C84
+:10F23000011D111D81E4E81682E4F8068FE008073D
+:10F2400080E0180770F3E0913A02F0913B020995D3
+:10F250008091C00087FFE9CF8091C6001F910F9178
+:10F26000FF90EF9008950E94D9F8982F809138026E
+:10F27000813049F0823091F091366CF490330CF08B
+:10F280009053892F08958091C00085FFFCCF909303
+:10F29000C60091369CF39755892F08958091C80038
+:10F2A00085FFFCCF9093CE00E7CF1F930E9433F9E8
+:10F2B000182F0E9433F91295107F810F1F91089526
+:10F2C000982F20913802992339F0213031F02230E3
+:10F2D00061F091509923C9F708958091C00087FF8C
+:10F2E000FCCF8091C6009150F5CF8091C80087FF78
+:10F2F000FCCF8091CE009150EDCF1F93182F0E942C
+:10F30000D9F8803249F0809139028F5F80933902B9
+:10F31000853091F11F910895809138028130B9F0C4
+:10F320008230C1F78091C80085FFFCCF84E18093D3
+:10F33000CE008091C80085FFFCCF1093CE00809155
+:10F34000C80085FFFCCF80E18093CE00E3CF8091A1
+:10F35000C00085FFFCCF84E18093C6008091C0008F
+:10F3600085FFFCCF1093C6008091C00085FFFCCFC5
+:10F3700080E18093C600CECFE0913A02F0913B024B
+:10F3800009951F9108950E94D9F8803241F080912B
+:10F3900039028F5F80933902853029F10895809179
+:10F3A0003802813089F08230C9F78091C80085FF2A
+:10F3B000FCCF84E18093CE008091C80085FFFCCF14
+:10F3C00080E18093CE0008958091C00085FFFCCF3E
+:10F3D00084E18093C6008091C00085FFFCCF80E16E
+:10F3E0008093C6000895E0913A02F0913B0209959E
+:10F3F000089540E951E08823A1F02F9A28EE33E0E8
+:10F40000FA013197F1F721503040D1F72F9828EECB
+:10F4100033E0FA013197F1F721503040D1F78150B4
+:10F4200061F708952F923F924F925F926F927F9271
+:10F430008F929F92AF92BF92CF92DF92EF92FF9204
+:10F440000F931F93CF93DF93000081E080933802E6
+:10F4500080E18093C4001092C5001092C00086E045
+:10F460008093C20088E18093C1006898709A279ABF
+:10F4700081E00E94F9F9E4E1EE2E7EE1D72E67E902
+:10F48000C62E53E0B52E40E1A42E9924939431E486
+:10F49000832E26E5722E92E5692E80E2582E09E42D
+:10F4A000402E13E5312EB0E52B2E0E94D9F8803383
+:10F4B000C9F1813309F452C0803409F4C8C08134E1
+:10F4C00009F4EAC0823489F1853409F4CAC0803570
+:10F4D00049F1823539F1813529F1853509F4ECC0DE
+:10F4E000863509F409C1843609F428C1843709F442
+:10F4F000ABC1853709F473C2863709F4D9C08132AC
+:10F5000009F4B7C2809139028F5F80933902853048
+:10F5100061F6E0913A02F0913B0209950E94D9F818
+:10F52000803339F60E94C3F9C0CF2091380293E1AD
+:10F5300005C0223061F09923A9F391502130C9F719
+:10F540008091C00087FFFCCF8091C600F4CF8091EE
+:10F55000C80087FFFCCF8091CE00EDCF0E94D9F884
+:10F56000803281F6809138028130D1F1823009F009
+:10F570009CCF8091C80085FFFCCFE092CE008091A7
+:10F58000C80085FFFCCF8092CE008091C80085FF27
+:10F59000FCCF7092CE008091C80085FFFCCF6092B6
+:10F5A000CE008091C80085FFFCCF5092CE008091A4
+:10F5B000C80085FFFCCF4092CE008091C80085FF37
+:10F5C000FCCF3092CE008091C80085FFFCCF209206
+:10F5D000CE008091C80085FFFCCFA092CE0065CF01
+:10F5E0008091C00085FFFCCFE092C6008091C000F2
+:10F5F00085FFFCCF8092C6008091C00085FFFCCFC4
+:10F600007092C6008091C00085FFFCCF6092C6005A
+:10F610008091C00085FFFCCF5092C6008091C00051
+:10F6200085FFFCCF4092C6008091C00085FFFCCFD3
+:10F630003092C6008091C00085FFFCCF2092C600AA
+:10F640008091C00085FFFCCFA092C6002ECF0E9403
+:10F65000D9F8863808F466CF0E94D9F80E94C3F919
+:10F6600024CF2091380294E0213041F0223069F01B
+:10F67000992309F457CF91502130C1F78091C000F0
+:10F6800087FFFCCF8091C600F3CF8091C80087FF31
+:10F69000FCCF8091CE00ECCF0E94D9F8803841F1A8
+:10F6A000813809F447C0823809F4CAC08839E1F0CA
+:10F6B00080E00E947DF9F9CE0E94D9F880933C0247
+:10F6C0000E94D9F880933D020E94C3F9EECE0E94B9
+:10F6D000D9F80E94D9F8182F0E94D9F8112309F4FB
+:10F6E0007EC2113009F40AC283E00E947DF9DDCEAA
+:10F6F00082E00E947DF9D9CE0E94D9F8803339F397
+:10F700002091380292E0213039F0223061F09923C3
+:10F7100079F291502130C9F78091C00087FFFCCF6A
+:10F720008091C600F4CF8091C80087FFFCCF809104
+:10F73000CE00EDCF81E00E947DF9B7CE0E94D9F8CE
+:10F7400080933F030E94D9F880933E038091420347
+:10F750008E7F809342030E94D9F8853409F4B3C1A7
+:10F7600080913E0390913F03892B89F000E010E0E7
+:10F770000E94D9F8F801E25CFD4F80830F5F1F4FB4
+:10F7800080913E0390913F030817190788F30E9468
+:10F79000D9F8803209F0B6CE8091420380FFB2C121
+:10F7A00040913C0250913D02440F551F50933D0241
+:10F7B00040933C0260913E0370913F0361157105D7
+:10F7C000F1F080E090E09A01280F391FFC01E25C23
+:10F7D000FD4FE081F999FECF1FBA32BD21BDE0BDDA
+:10F7E0000FB6F894FA9AF99A0FBE01968617970702
+:10F7F00050F3460F571F50933D0240933C028091B7
+:10F800003802813081F0823009F04FCE8091C800FB
+:10F8100085FFFCCFE092CE008091C80085FFFCCF31
+:10F82000A092CE0042CE8091C00085FFFCCFE09236
+:10F83000C6008091C00085FFFCCFA092C60035CEE7
+:10F8400080E10E947DF931CE0E94D9F880933F0378
+:10F850000E94D9F880933E0320913C0230913D02F2
+:10F8600037FD46C1809142038D7F80934203220F72
+:10F87000331F30933D0220933C020E94D9F8853417
+:10F8800009F430C1809142038E7F809342030E942D
+:10F89000D9F8803209F009CE60913802613009F45C
+:10F8A0006FC0623009F473C000913E0310913F03B2
+:10F8B0000115110509F440C080914203782F717041
+:10F8C000F82EF69481E0F82240913C0250913D02DE
+:10F8D00020E030E013C0FF2009F060C0FA019491ED
+:10F8E000613009F43BC0623009F441C0CA0101969D
+:10F8F0002F5F3F4FAC0120173107D0F4772359F326
+:10F90000F999FECF52BD41BDF89A90B56130F9F03A
+:10F91000623061F78091C80085FFFCCF9093CE00E4
+:10F92000CA0101962F5F3F4FAC012017310730F31A
+:10F9300090933D0280933C02613009F4CAC062306A
+:10F9400009F0B3CD8091C80085FFFCCF46CE8091F1
+:10F95000C00085FFFCCF9093C600C8CF8091C00047
+:10F9600085FDF9CF8091C00085FFF8CFF4CF80915D
+:10F97000C80085FDD3CF8091C80085FFF8CFCECFDA
+:10F980008091C00085FFFCCFE092C6008DCF8091B2
+:10F99000C80085FFFCCFE092CE0086CFCA01A0E070
+:10F9A000B0E080509040AF4FBF4FABBFFC0197918C
+:10F9B000613061F0623009F099CF8091C80085FD17
+:10F9C000ADCF8091C80085FFF8CFA8CF8091C0004F
+:10F9D00085FDC1CF8091C00085FFF8CFBCCF0E94CC
+:10F9E000D9F8803209F08ECD80913802813011F142
+:10F9F000823009F05ACD8091C80085FFFCCFE0929B
+:10FA0000CE008091C80085FFFCCFD092CE008091BF
+:10FA1000C80085FFFCCFC092CE008091C80085FF52
+:10FA2000FCCFB092CE008091C80085FFFCCFA092A1
+:10FA3000CE003BCD8091C00085FFFCCFE092C60098
+:10FA40008091C00085FFFCCFD092C6008091C0009D
+:10FA500085FFFCCFC092C6008091C00085FFFCCF1F
+:10FA6000B092C6008091C00085FFFCCFA092C60076
+:10FA70001CCD0E94D9F8813209F017CD0E94D9F827
+:10FA8000813209F012CD279A2F98109240032091CD
+:10FA90003802E1E491E00EC0223009F4A4C0909352
+:10FAA0004003E92FF0E0E050FE4FE0819F5FEE233E
+:10FAB00009F4A0C0213081F78091C00085FFFCCF00
+:10FAC000E093C600ECCF80914203816080934203B3
+:10FAD00047CE8091C00085FDB7CD8091C00085FFE5
+:10FAE000F8CFB2CD80914203816080934203CFCEA4
+:10FAF00080914203826080934203B9CE87E90E94DD
+:10FB00007DF9D3CC80913D028823880F880B892111
+:10FB1000809341038BBF80913C0290913D02880FFE
+:10FB2000991F90933D0280933C0280913E0380FF99
+:10FB300009C080913E0390913F03019690933F034B
+:10FB400080933E03F894F999FECF1127E0913C028F
+:10FB5000F0913D02CEE3D2E080913E0390913F03CD
+:10FB6000103091F40091570001700130D9F303E097
+:10FB700000935700E8950091570001700130D9F3C8
+:10FB800001E100935700E895099019900091570002
+:10FB900001700130D9F301E000935700E895139507
+:10FBA000103898F011270091570001700130D9F3F7
+:10FBB00005E000935700E89500915700017001306F
+:10FBC000D9F301E100935700E8953296029709F0C6
+:10FBD000C7CF103011F00296E5CF112410CE8EE180
+:10FBE0000E947DF962CC8091C80085FFFCCFE09334
+:10FBF000CE0055CF7AE0B72E6DE0A62E5AE3952EB3
+:10FC000040E2842E3DE3732E90E3692E81E3582E6B
+:10FC1000213009F442C0223009F45FC00E94D9F8B3
+:10FC2000982F20913802213089F1223009F44EC0FA
+:10FC3000943709F46BC0923709F405C1973709F47A
+:10FC40007BC0953799F0923609F4BDC09A3601F71A
+:10FC5000E0913A02F0913B02099520913802D8CF09
+:10FC60008091C00085FFFCCF9093C6000E94D9F818
+:10FC7000982F80913802813099F38230B9F78091C2
+:10FC8000C80085FFFCCF9093CE00F0CF8091C000DC
+:10FC900085FFFCCF9093C600CBCF8091C00085FF3D
+:10FCA000FCCFB092C6008091C00085FFFCCFA0922F
+:10FCB000C6008091C00085FFFCCF9092C600809165
+:10FCC000C00085FFFCCF8092C600A8CF8091C800FD
+:10FCD00085FFFCCF9093CE00ABCF8091C80085FF0D
+:10FCE000FCCFB092CE008091C80085FFFCCFA092DF
+:10FCF000CE008091C80085FFFCCF9092CE0080910D
+:10FD0000C80085FFFCCF8092CE0088CF1F9947C0E6
+:10FD10002F9A213051F0223009F07ACF8091C8001B
+:10FD200085FFFCCF6092CE0073CF8091C00085FF2D
+:10FD3000FCCF6092C6006CCF0E94D9F8982F8091BA
+:10FD400038028130F1F0823009F4ABC00E9455F9DD
+:10FD5000082F0E9455F9182F0E94D9F8982F8091EA
+:10FD600038028130A9F0823009F4A2C00E9455F90E
+:10FD7000D02ECC24F601E10FF11D808320913802B2
+:10FD800047CF8091C00085FFFCCF9093C600DECFA7
+:10FD90008091C00085FFFCCF9093C600E7CF2F98DD
+:10FDA000213051F0223009F033CF8091C80085FF17
+:10FDB000FCCF5092CE002CCF8091C00085FFFCCFAD
+:10FDC0005092C60025CF213041F1223081F080E8E9
+:10FDD00085BF109274001092750080E091E1FC01E3
+:10FDE000819180E091E13097D1F3CF01F8CF8091FC
+:10FDF000C80085FFFCCF82E68093CE008091C800CA
+:10FE000085FFFCCF85E78093CE008091C80085FFF9
+:10FE1000FCCF83E78093CE00DACF8091C00085FFCE
+:10FE2000FCCF82E68093C6008091C00085FFFCCFA6
+:10FE300085E78093C6008091C00085FFFCCF83E7F3
+:10FE40008093C600C4CF0E94D9F8982F80913802C1
+:10FE50008130C9F08230D1F10E9455F9182F0E94EB
+:10FE600055F9982F809138028130A1F0823039F114
+:10FE7000F12EEE24F701E90FF11D80810E9494F824
+:10FE800020913802C5CE8091C00085FFFCCF9093B1
+:10FE9000C600E2CF8091C00085FFFCCF7092C60003
+:10FEA000E7CF8091C80085FFFCCF9093CE004ECF66
+:10FEB0008091C80085FFFCCF9093CE0057CF8091F2
+:10FEC000C80085FFFCCF7092CE00D2CF8091C800D1
+:0EFED00085FFFCCF9093CE00BFCFF894FFCFFC
+:10FEDE0041546D656761424F4F54202F204172642B
+:10FEEE0075696E6F204D656761202D20284329208E
+:10FEFE0041726475696E6F204C4C43202D20303951
+:08FF0E00303933300A0D008088
+:040000031000F000F9
+:00000001FF
diff --git a/bootloaders/atmega/ATmegaBOOT_168_atmega328.hex b/bootloaders/atmega/ATmegaBOOT_168_atmega328.hex
new file mode 100644
index 0000000..43a8b30
--- /dev/null
+++ b/bootloaders/atmega/ATmegaBOOT_168_atmega328.hex
@@ -0,0 +1,125 @@
+:107800000C94343C0C94513C0C94513C0C94513CE1
+:107810000C94513C0C94513C0C94513C0C94513CB4
+:107820000C94513C0C94513C0C94513C0C94513CA4
+:107830000C94513C0C94513C0C94513C0C94513C94
+:107840000C94513C0C94513C0C94513C0C94513C84
+:107850000C94513C0C94513C0C94513C0C94513C74
+:107860000C94513C0C94513C11241FBECFEFD8E036
+:10787000DEBFCDBF11E0A0E0B1E0ECE9FFE702C060
+:1078800005900D92A230B107D9F712E0A2E0B1E065
+:1078900001C01D92AD30B107E1F70E942D3D0C945F
+:1078A000CC3F0C94003C982F959595959595959582
+:1078B000905D8F708A307CF0282F295A8091C0000B
+:1078C00085FFFCCF9093C6008091C00085FFFCCF60
+:1078D0002093C6000895282F205DF0CF982F809127
+:1078E000C00085FFFCCF9093C6000895EF92FF92F1
+:1078F0000F931F93EE24FF2487018091C00087FD22
+:1079000017C00894E11CF11C011D111D81E4E8164B
+:1079100082E4F8068FE0080780E0180770F3E09132
+:107920000401F091050109958091C00087FFE9CF1E
+:107930008091C6001F910F91FF90EF9008950E94D3
+:10794000763C982F8091C00085FFFCCF9093C600B5
+:1079500091362CF490330CF09053892F089597555D
+:10796000892F08951F930E949F3C182F0E949F3CCF
+:107970001295107F810F1F9108951F93182F882350
+:1079800021F00E94763C1150E1F71F9108951F935A
+:10799000182F0E94763C803249F0809103018F5F5E
+:1079A000809303018530C1F01F9108958091C0003C
+:1079B00085FFFCCF84E18093C6008091C00085FFE5
+:1079C000FCCF1093C6008091C00085FFFCCF80E102
+:1079D0008093C6001F910895E0910401F091050184
+:1079E00009951F9108950E94763C803241F0809164
+:1079F00003018F5F80930301853081F008958091AA
+:107A0000C00085FFFCCF84E18093C6008091C00058
+:107A100085FFFCCF80E18093C6000895E0910401CA
+:107A2000F09105010995089540E951E08823A1F0FE
+:107A30002D9A28EE33E0FA013197F1F721503040CA
+:107A4000D1F72D9828EE33E0FA013197F1F7215064
+:107A50003040D1F7815061F708953F924F925F9285
+:107A60006F927F928F929F92AF92BF92CF92DF924E
+:107A7000EF92FF920F931F93CF93DF93000080E16B
+:107A80008093C4001092C50088E18093C10086E015
+:107A90008093C2005098589A259A81E00E94143D24
+:107AA00024E1F22E9EE1E92E85E9D82E0FE0C02ECA
+:107AB00010E1B12EAA24A394B1E49B2EA6E58A2E50
+:107AC000F2E57F2EE0E26E2E79E4572E63E5462E36
+:107AD00050E5352E0E94763C8033B1F18133B9F107
+:107AE000803409F46FC0813409F476C0823409F41B
+:107AF00085C0853409F488C0803531F1823521F1A3
+:107B0000813511F1853509F485C0863509F48DC0BC
+:107B1000843609F496C0843709F403C1853709F423
+:107B200072C1863709F466C0809103018F5F80932C
+:107B30000301853079F6E0910401F0910501099582
+:107B40000E94763C803351F60E94F33CC3CF0E94E2
+:107B5000763C803249F78091C00085FFFCCFF092DF
+:107B6000C6008091C00085FFFCCF9092C600809136
+:107B7000C00085FFFCCF8092C6008091C00085FFC9
+:107B8000FCCF7092C6008091C00085FFFCCF609250
+:107B9000C6008091C00085FFFCCF5092C600809146
+:107BA000C00085FFFCCF4092C6008091C00085FFD9
+:107BB000FCCF3092C6008091C00085FFFCCFB09210
+:107BC000C60088CF0E94763C863808F4BDCF0E945C
+:107BD000763C0E94F33C7ECF0E94763C803809F4CC
+:107BE0009CC0813809F40BC1823809F43CC1883942
+:107BF00009F48FC080E00E94C73C6CCF84E10E94F2
+:107C0000BD3C0E94F33C66CF85E00E94BD3C0E94D3
+:107C1000F33C60CF0E94763C809306010E94763C44
+:107C2000809307010E94F33C55CF0E94763C80333D
+:107C300009F41DC183E00E94BD3C80E00E94C73C66
+:107C400049CF0E94763C809309020E94763C809343
+:107C5000080280910C028E7F80930C020E94763C79
+:107C6000853409F415C18091080290910902892B8D
+:107C700089F000E010E00E94763CF801E85FFE4FDA
+:107C800080830F5F1F4F80910802909109020817AF
+:107C9000190788F30E94763C803209F045CF809125
+:107CA0000C0280FF01C16091060170910701660F0F
+:107CB000771F7093070160930601A0910802B091AD
+:107CC00009021097C9F0E8E0F1E09B01AD014E0F09
+:107CD0005F1FF999FECF32BD21BD819180BDFA9A17
+:107CE000F99A2F5F3F4FE417F50799F76A0F7B1F4B
+:107CF00070930701609306018091C00085FFFCCF5F
+:107D0000F092C6008091C00085FFFCCFB092C60003
+:107D1000E1CE83E00E94C73CDDCE82E00E94C73CFA
+:107D2000D9CE0E94763C809309020E94763C8093D3
+:107D300008028091060190910701880F991F909386
+:107D40000701809306010E94763C853409F4A6C0A1
+:107D500080910C028E7F80930C020E94763C8032D0
+:107D600009F0B8CE8091C00085FFFCCFF092C6002C
+:107D7000609108027091090261157105B9F140E046
+:107D800050E080910C02A82FA170B82FB27011C0E2
+:107D9000BB2309F45CC0E0910601F0910701319624
+:107DA000F0930701E09306014F5F5F4F46175707B7
+:107DB000E8F4AA2369F3F999FECF209106013091E6
+:107DC000070132BD21BDF89A90B58091C00085FFB2
+:107DD000FCCF9093C6002F5F3F4F30930701209355
+:107DE00006014F5F5F4F4617570718F38091C00099
+:107DF00085FDE5CE8091C00085FFF8CFE0CE81E023
+:107E00000E94C73C67CE0E94763C803209F08CCE3F
+:107E10008091C00085FFFCCFF092C6008091C00029
+:107E200085FFFCCFE092C6008091C00085FFFCCFAB
+:107E3000D092C6008091C00085FFFCCFC092C600E2
+:107E40008091C00085FFFCCFB092C60043CEE09188
+:107E50000601F091070194918091C00085FFFCCF4D
+:107E60009093C6009CCF80E10E94C73C33CE0E9415
+:107E7000763C0E94763C182F0E94763C112309F430
+:107E800083C0113009F484C08FE00E94C73C22CE29
+:107E900080910C02816080930C02E5CE80910C02EF
+:107EA000816080930C0259CF809107018823880F4D
+:107EB000880B8A2180930B02809106019091070123
+:107EC000880F991F90930701809306018091080203
+:107ED00080FF09C080910802909109020196909359
+:107EE000090280930802F894F999FECF1127E091D6
+:107EF0000601F0910701C8E0D1E08091080290915D
+:107F00000902103091F40091570001700130D9F34B
+:107F100003E000935700E89500915700017001308D
+:107F2000D9F301E100935700E89509901990009169
+:107F3000570001700130D9F301E000935700E89534
+:107F40001395103498F011270091570001700130FB
+:107F5000D9F305E000935700E895009157000170B0
+:107F60000130D9F301E100935700E895329602976A
+:107F700009F0C7CF103011F00296E5CF112480919F
+:107F8000C00085FFB9CEBCCE8EE10E94C73CA2CD19
+:0C7F900085E90E94C73C9ECDF894FFCF0D
+:027F9C00800063
+:040000030000780081
+:00000001FF
diff --git a/bootloaders/atmega/ATmegaBOOT_168_atmega328_pro_8MHz.hex b/bootloaders/atmega/ATmegaBOOT_168_atmega328_pro_8MHz.hex
new file mode 100644
index 0000000..9753e2e
--- /dev/null
+++ b/bootloaders/atmega/ATmegaBOOT_168_atmega328_pro_8MHz.hex
@@ -0,0 +1,124 @@
+:107800000C94343C0C94513C0C94513C0C94513CE1
+:107810000C94513C0C94513C0C94513C0C94513CB4
+:107820000C94513C0C94513C0C94513C0C94513CA4
+:107830000C94513C0C94513C0C94513C0C94513C94
+:107840000C94513C0C94513C0C94513C0C94513C84
+:107850000C94513C0C94513C0C94513C0C94513C74
+:107860000C94513C0C94513C11241FBECFEFD8E036
+:10787000DEBFCDBF11E0A0E0B1E0EAE8FFE702C063
+:1078800005900D92A230B107D9F712E0A2E0B1E065
+:1078900001C01D92AD30B107E1F70E942D3D0C945F
+:1078A000C33F0C94003C982F95959595959595958B
+:1078B000905D8F708A307CF0282F295A8091C0000B
+:1078C00085FFFCCF9093C6008091C00085FFFCCF60
+:1078D0002093C6000895282F205DF0CF982F809127
+:1078E000C00085FFFCCF9093C6000895EF92FF92F1
+:1078F0000F931F93EE24FF2487018091C00087FD22
+:1079000017C00894E11CF11C011D111D81E2E8164D
+:1079100081EAF80687E0080780E0180770F3E09135
+:107920000401F091050109958091C00087FFE9CF1E
+:107930008091C6001F910F91FF90EF9008950E94D3
+:10794000763C982F8091C00085FFFCCF9093C600B5
+:1079500091362CF490330CF09053892F089597555D
+:10796000892F08951F930E949F3C182F0E949F3CCF
+:107970001295107F810F1F9108951F93182F882350
+:1079800021F00E94763C1150E1F71F9108951F935A
+:10799000182F0E94763C803249F0809103018F5F5E
+:1079A000809303018530C1F01F9108958091C0003C
+:1079B00085FFFCCF84E18093C6008091C00085FFE5
+:1079C000FCCF1093C6008091C00085FFFCCF80E102
+:1079D0008093C6001F910895E0910401F091050184
+:1079E00009951F9108950E94763C803241F0809164
+:1079F00003018F5F80930301853081F008958091AA
+:107A0000C00085FFFCCF84E18093C6008091C00058
+:107A100085FFFCCF80E18093C6000895E0910401CA
+:107A2000F09105010995089548EC50E08823A1F0F4
+:107A30002D9A28EE33E0FA013197F1F721503040CA
+:107A4000D1F72D9828EE33E0FA013197F1F7215064
+:107A50003040D1F7815061F708953F924F925F9285
+:107A60006F927F928F929F92AF92BF92CF92DF924E
+:107A7000EF92FF920F931F93CF93DF93000082E06A
+:107A80008093C00080E18093C4001092C50088E11B
+:107A90008093C10086E08093C2005098589A259A3E
+:107AA00081E00E94143D24E1F22E9EE1E92E85E959
+:107AB000D82E0FE0C02E10E1B12EAA24A394B1E479
+:107AC0009B2EA6E58A2EF2E57F2EE0E26E2E79E46B
+:107AD000572E63E5462E50E5352E0E94763C8033C6
+:107AE000B1F18133B9F1803409F46FC0813409F404
+:107AF00076C0823409F485C0853409F488C08035A5
+:107B000031F1823521F1813511F1853509F485C0D6
+:107B1000863509F48DC0843609F496C0843709F49B
+:107B200003C1853709F472C1863709F466C08091B4
+:107B300003018F5F80930301853079F6E0910401A2
+:107B4000F091050109950E94763C803351F60E9420
+:107B5000F33CC3CF0E94763C803249F78091C0004D
+:107B600085FFFCCFF092C6008091C00085FFFCCF5E
+:107B70009092C6008091C00085FFFCCF8092C60025
+:107B80008091C00085FFFCCF7092C6008091C0003C
+:107B900085FFFCCF6092C6008091C00085FFFCCFBE
+:107BA0005092C6008091C00085FFFCCF4092C60075
+:107BB0008091C00085FFFCCF3092C6008091C0004C
+:107BC00085FFFCCFB092C60088CF0E94763C8638F5
+:107BD00008F4BDCF0E94763C0E94F33C7ECF0E9409
+:107BE000763C803809F49CC0813809F40BC1823896
+:107BF00009F430C1883909F48FC080E00E94C73C85
+:107C00006CCF84E10E94BD3C0E94F33C66CF85E0CE
+:107C10000E94BD3C0E94F33C60CF0E94763C809362
+:107C200006010E94763C809307010E94F33C55CFE9
+:107C30000E94763C803309F411C183E00E94BD3C70
+:107C400080E00E94C73C49CF0E94763C80930902A5
+:107C50000E94763C8093080280910C028E7F809374
+:107C60000C020E94763C853409F409C18091080217
+:107C700090910902892B89F000E010E00E94763C87
+:107C8000F801E85FFE4F80830F5F1F4F809108026D
+:107C9000909109020817190788F30E94763C8032F8
+:107CA00009F045CF80910C0280FFF5C0609106017C
+:107CB00070910701660F771F7093070160930601AB
+:107CC000A0910802B09109021097C9F0E8E0F1E034
+:107CD0009B01AD014E0F5F1FF999FECF32BD21BD53
+:107CE000819180BDFA9AF99A2F5F3F4FE417F5070B
+:107CF00099F76A0F7B1F70930701609306018091CB
+:107D0000C00085FFFCCFF092C6008091C00085FFC7
+:107D1000FCCFB092C600E1CE83E00E94C73CDDCE2E
+:107D200082E00E94C73CD9CE0E94763C8093090233
+:107D30000E94763C80930802809106019091070191
+:107D4000880F991F90930701809306010E94763C4B
+:107D5000853409F49AC080910C028E7F80930C02C6
+:107D60000E94763C803209F0B8CE8091C00085FF39
+:107D7000FCCFF092C600A0910802B09109021097C2
+:107D8000C1F180910C02082F0170182F1695117007
+:107D9000E0910601F0910701AF014F5F5F4FBA011B
+:107DA00020E030E00023B1F4112339F49491809164
+:107DB000C00085FFFCCF9093C6002F5F3F4FCB01E3
+:107DC0000196FA012A173B0780F4BC014F5F5F4F11
+:107DD000002351F3F999FECFF2BDE1BDF89A90B5B9
+:107DE0008091C00085FFFCCFE6CF709307016093C0
+:107DF00006018091C00085FDE5CE8091C00085FF21
+:107E0000F8CFE0CE81E00E94C73C67CE0E94763C6E
+:107E1000803209F08CCE8091C00085FFFCCFF092BB
+:107E2000C6008091C00085FFFCCFE092C600809123
+:107E3000C00085FFFCCFD092C6008091C00085FFB6
+:107E4000FCCFC092C6008091C00085FFFCCFB092ED
+:107E5000C60043CE80E10E94C73C3FCE0E94763CE4
+:107E60000E94763C182F0E94763C112309F483C0AF
+:107E7000113009F484C08FE00E94C73C2ECE80915F
+:107E80000C02816080930C02F1CE80910C02816023
+:107E900080930C0265CF809107018823880F880B9F
+:107EA0008A2180930B028091060190910701880F2F
+:107EB000991F90930701809306018091080280FF2B
+:107EC00009C08091080290910902019690930902DD
+:107ED00080930802F894F999FECF1127E0910601EA
+:107EE000F0910701C8E0D1E0809108029091090269
+:107EF000103091F40091570001700130D9F303E084
+:107F000000935700E8950091570001700130D9F3B4
+:107F100001E100935700E8950990199000915700EE
+:107F200001700130D9F301E000935700E8951395F3
+:107F3000103498F011270091570001700130D9F3E7
+:107F400005E000935700E89500915700017001305B
+:107F5000D9F301E100935700E8953296029709F0B2
+:107F6000C7CF103011F00296E5CF11248091C000E8
+:107F700085FFC5CEC8CE8EE10E94C73CAECD85E957
+:0A7F80000E94C73CAACDF894FFCF81
+:027F8A00800075
+:040000030000780081
+:00000001FF
diff --git a/bootloaders/atmega/ATmegaBOOT_168_diecimila.hex b/bootloaders/atmega/ATmegaBOOT_168_diecimila.hex
new file mode 100644
index 0000000..feac9d2
--- /dev/null
+++ b/bootloaders/atmega/ATmegaBOOT_168_diecimila.hex
@@ -0,0 +1,126 @@
+:103800000C94341C0C94511C0C94511C0C94511CA1
+:103810000C94511C0C94511C0C94511C0C94511C74
+:103820000C94511C0C94511C0C94511C0C94511C64
+:103830000C94511C0C94511C0C94511C0C94511C54
+:103840000C94511C0C94511C0C94511C0C94511C44
+:103850000C94511C0C94511C0C94511C0C94511C34
+:103860000C94511C0C94511C11241FBECFEFD4E0BA
+:10387000DEBFCDBF11E0A0E0B1E0E4EAFFE302C0AB
+:1038800005900D92A230B107D9F712E0A2E0B1E0A5
+:1038900001C01D92AD30B107E1F70E94361D0C94B6
+:1038A000D01F0C94001C982F9595959595959595FE
+:1038B000905D8F708A307CF0282F295A8091C0004B
+:1038C00085FFFCCF9093C6008091C00085FFFCCFA0
+:1038D0002093C6000895282F205DF0CF982F809167
+:1038E000C00085FFFCCF9093C6000895EF92FF9231
+:1038F0000F931F93EE24FF2487018091C00087FD62
+:1039000017C00894E11CF11C011D111D81E4E8168B
+:1039100082E4F8068FE0080780E0180770F3E09172
+:103920000401F091050109958091C00087FFE9CF5E
+:103930008091C6001F910F91FF90EF9008950E9413
+:10394000761C982F8091C00085FFFCCF9093C60015
+:1039500091362CF490330CF09053892F089597559D
+:10396000892F08951F930E949F1C182F0E949F1C4F
+:103970001295107F810F1F910895882351F0982F81
+:1039800091508091C00087FFFCCF8091C6009923A1
+:10399000B9F708951F93182F0E94761C803249F0C2
+:1039A000809103018F5F809303018530C1F01F91E7
+:1039B00008958091C00085FFFCCF84E18093C6000C
+:1039C0008091C00085FFFCCF1093C6008091C0009D
+:1039D00085FFFCCF80E18093C6001F910895E091A0
+:1039E0000401F091050109951F9108950E94761C2C
+:1039F000803241F0809103018F5F80930301853015
+:103A000081F008958091C00085FFFCCF84E1809310
+:103A1000C6008091C00085FFFCCF80E18093C60086
+:103A20000895E0910401F09105010995089510921F
+:103A30000A028823D1F090E040E951E02D9A28EE67
+:103A400033E0FA013197F1F721503040D1F72D984A
+:103A500028EE33E0FA013197F1F721503040D1F7E9
+:103A60009F5F981758F380930A0208953F924F92F0
+:103A70005F926F927F928F929F92AF92BF92CF92FE
+:103A8000DF92EF92FF920F931F93CF93DF9300008B
+:103A900083E38093C4001092C50088E18093C10045
+:103AA00086E08093C2005098589A259A81E00E943F
+:103AB000171D44E1F42E3EE1E32E24E9D22E96E0D8
+:103AC000C92E80E1B82EAA24A39401E4902E16E515
+:103AD000812EB2E57B2EA0E26A2EF9E45F2EE3E5AB
+:103AE0004E2E70E5372E0E94761C8033B1F1813363
+:103AF00009F441C0803409F479C0813409F48CC0E0
+:103B0000823471F1853409F47BC0803531F182351E
+:103B100021F1813511F1853509F48DC0863509F41F
+:103B20009DC0843609F4AEC0843709F41BC18537C3
+:103B300009F485C1863709F47AC0809103018F5F4B
+:103B400080930301853079F6E0910401F09105013D
+:103B500009950E94761C803351F60E94F61CC3CF53
+:103B600093E18091C00087FFFCCF8091C60099232C
+:103B7000A1F39150F6CF0E94761C8032F1F680912D
+:103B8000C00085FFFCCFF092C6008091C00085FF89
+:103B9000FCCF9092C6008091C00085FFFCCF809240
+:103BA000C6008091C00085FFFCCF7092C600809156
+:103BB000C00085FFFCCF6092C6008091C00085FFE9
+:103BC000FCCF5092C6008091C00085FFFCCF409290
+:103BD000C6008091C00085FFFCCF3092C600809166
+:103BE000C00085FFFCCFB092C6007DCF0E94761C3E
+:103BF000863808F4B2CF0E94761C0E94F61C73CF60
+:103C000094E08091C00087FFFCCF8091C60099238B
+:103C100009F4A3CF9150F5CF0E94761C8038D1F0E3
+:103C2000813861F1823809F499C0883979F080E0EF
+:103C30000E94CA1C58CF0E94761C809306010E94E5
+:103C4000761C809307010E94F61C4DCF83E00E94F2
+:103C5000CA1C49CF82E00E94CA1C45CF0E94761C34
+:103C6000803309F486C192E08091C00087FFFCCFC9
+:103C70008091C6009923D9F29150F6CF81E00E943D
+:103C8000CA1C31CF0E94761C809309020E94761CC8
+:103C90008093080280910C028E7F80930C020E9418
+:103CA000761C853429F480910C02816080930C028B
+:103CB0008091080290910902892B89F000E010E0C0
+:103CC0000E94761CF801E85FFE4F80830F5F1F4F54
+:103CD00080910802909109020817190788F30E9441
+:103CE000761C803209F029CF80910C0280FFD1C070
+:103CF0004091060150910701440F551F5093070151
+:103D000040930601A0910802B09109021097C9F0F2
+:103D1000E8E0F1E09A01BD016E0F7F1FF999FECF37
+:103D200032BD21BD819180BDFA9AF99A2F5F3F4F34
+:103D3000E617F70799F74A0F5B1F50930701409367
+:103D400006018091C00085FFFCCFF092C6008091F3
+:103D5000C00085FFFCCFB092C600C5CE80E10E94B6
+:103D6000CA1CC1CE0E94761C809309020E94761C58
+:103D7000809308028091060190910701880F991F96
+:103D800090930701809306010E94761C853409F404
+:103D90007AC080910C028E7F80930C020E94761C68
+:103DA000803209F0A0CE8091C00085FFFCCFF09258
+:103DB000C600A0910802B09109021097B9F1809154
+:103DC0000C02182F1170082F0270E0910601F0917B
+:103DD00007019F012F5F3F4FB90140E050E01123E1
+:103DE000B1F4002339F494918091C00085FFFCCF99
+:103DF0009093C6004F5F5F4FCB010196F9014A17C0
+:103E00005B0780F4BC012F5F3F4F112351F3F999F9
+:103E1000FECFF2BDE1BDF89A90B58091C00085FF5C
+:103E2000FCCFE6CF70930701609306018091C0003C
+:103E300085FDD9CE8091C00085FFF8CFD4CE0E94F9
+:103E4000761C803209F079CE8091C00085FFFCCFCE
+:103E5000F092C6008091C00085FFFCCFE092C600C2
+:103E60008091C00085FFFCCFD092C6008091C00039
+:103E700085FFFCCFC092C6008091C00085FFFCCFBB
+:103E8000B092C60030CE80910C02816080930C020B
+:103E900085CF809107018823880F880B8A21809322
+:103EA0000B028091060190910701880F991F909352
+:103EB0000701809306018091080280FF09C080916C
+:103EC00008029091090201969093090280930802DA
+:103ED000F894F999FECF1127E0910601F0910701BE
+:103EE000C8E0D1E08091080290910902103091F46D
+:103EF0000091570001700130D9F303E0009357009F
+:103F0000E8950091570001700130D9F301E1009369
+:103F10005700E89509901990009157000170013001
+:103F2000D9F301E000935700E8951395103498F009
+:103F300011270091570001700130D9F305E000937B
+:103F40005700E8950091570001700130D9F301E165
+:103F500000935700E8953296029709F0C7CF1030CA
+:103F600011F00296E5CF11248091C00085FFE9CEC3
+:103F7000ECCE0E94761C0E94761C182F0E94761CA4
+:103F8000112351F0113021F086E00E94CA1CABCD04
+:103F900084E90E94CA1CA7CD8EE10E94CA1CA3CD51
+:043FA000F894FFCFC3
+:023FA40080009B
+:0400000300003800C1
+:00000001FF
diff --git a/bootloaders/atmega/ATmegaBOOT_168_ng.hex b/bootloaders/atmega/ATmegaBOOT_168_ng.hex
new file mode 100644
index 0000000..387091e
--- /dev/null
+++ b/bootloaders/atmega/ATmegaBOOT_168_ng.hex
@@ -0,0 +1,110 @@
+:103800000C94341C0C94511C0C94511C0C94511CA1
+:103810000C94511C0C94511C0C94511C0C94511C74
+:103820000C94511C0C94511C0C94511C0C94511C64
+:103830000C94511C0C94511C0C94511C0C94511C54
+:103840000C94511C0C94511C0C94511C0C94511C44
+:103850000C94511C0C94511C0C94511C0C94511C34
+:103860000C94511C0C94511C11241FBECFEFD4E0BA
+:10387000DEBFCDBF11E0A0E0B1E0E4EAFEE302C0AC
+:1038800005900D92A230B107D9F712E0A2E0B1E0A5
+:1038900001C01D92AD30B107E1F70E94ED1C0C9400
+:1038A000511F0C94001C482F10920A0280E08417CC
+:1038B000E0F4582F2D9A28EE33E080E991E001974B
+:1038C000F1F721503040C9F72D9828EE33E080E918
+:1038D00091E00197F1F721503040C9F7852F8F5FB4
+:1038E000582F841738F380930A020895EF92FF92BD
+:1038F0000F931F93EE24FF2487018091C00087FD62
+:1039000017C00894E11CF11C011D111D81E0E8168F
+:1039100082E1F8068AE7080780E0180770F3E09173
+:103920000201F091030109958091C00087FFE9CF62
+:103930008091C600992787FD90951F910F91FF9068
+:10394000EF900895982F8091C00085FFFCCF909351
+:10395000C60008950E94761C803271F080910401A7
+:103960008F5F80930401853009F00895E091020192
+:10397000F09103010995089584E10E94A21C80E161
+:103980000E94A21C0895CF93C82F0E94761C8032FB
+:1039900041F0809104018F5F80930401853081F4B0
+:1039A0000AC084E10E94A21C8C2F0E94A21C80E10C
+:1039B0000E94A21C05C0E0910201F091030109954B
+:1039C000CF910895CF93C82FC150CF3F21F00E94CF
+:1039D000761CC150E0F7CF910895CFEFD4E0DEBF61
+:1039E000CDBF000083E38093C4001092C50088E13E
+:1039F0008093C10086E08093C2005098589A259A1F
+:103A000083E00E94531C0E94761C8033B1F1813305
+:103A1000B9F1803409F455C0813409F45BC08234B3
+:103A200009F46DC0853409F470C0803531F18235F8
+:103A300021F1813511F1853509F46BC0863509F422
+:103A400073C0843609F47AC0843709F4CEC0853750
+:103A500009F429C1863709F44AC0809104018F5FB7
+:103A600080930401853079F6E0910201F091030121
+:103A700009950E94761C803351F60E94AA1CC3CF80
+:103A80000E94761CC82F803241F784E10E94A21C5C
+:103A900081E40E94A21C86E50E94A21C82E50E948D
+:103AA000A21C8C2F0E94A21C89E40E94A21C83E508
+:103AB0000E94A21C80E50E94A21C80E10E94A21C20
+:103AC000A2CF0E94761C8638C0F20E94761C0E940B
+:103AD000AA1C99CF0E94761C803809F486C18138CF
+:103AE00009F487C1823809F488C1883921F080E05F
+:103AF0000E94C31C88CF83E00E94C31C84CF84E152
+:103B00000E94E21C0E94AA1C7ECF85E00E94E21C5B
+:103B1000F9CF0E94761C809306010E94761C809348
+:103B200007010E94AA1C6FCF0E94761C803309F403
+:103B3000CAC083E00E94E21C80E0DACF0E94761CBB
+:103B4000809309020E94761C8093080280910C02E7
+:103B50008E7F80930C020E94761C853409F4C4C0C9
+:103B600000E010E0809108029091090218161906F1
+:103B700070F4C8E0D1E00E94761C89930F5F1F4F5C
+:103B8000809108029091090208171907A0F30E947A
+:103B9000761C803209F061CF80910C0280FFAEC0AC
+:103BA000E0910601F0910701EE0FFF1F00E010E029
+:103BB00020910802309109021216130680F4A8E041
+:103BC000B1E0F999FECFF2BDE1BD8D9180BDFA9AC9
+:103BD000F99A31960F5F1F4F0217130790F3F09376
+:103BE0000701E093060184E166CF0E94761C809372
+:103BF00009020E94761C8093080280910601909130
+:103C00000701880F991F90930701809306010E9476
+:103C1000761C853409F46EC080910C028E7F8093EF
+:103C20000C020E94761C803209F0EDCE84E10E94E5
+:103C3000A21C00E010E02091080230910902121647
+:103C4000130608F03ACFE0910601F0910701809148
+:103C50000C0280FF1FC0F999FECFF2BDE1BDF89ABA
+:103C600080B50E94A21CE0910601F09107013196F7
+:103C7000F0930701E09306012091080230910902B8
+:103C80000F5F1F4F0217130708F017CF80910C0228
+:103C900080FDE1CF869580FFB4C03196F093070197
+:103CA000E0930601EDCF0E94761C803209F0D5CE5C
+:103CB00084E10E94A21C8EE10E94A21C84E90E9461
+:103CC000A21C86E0F8CE0E94761C0E94761CC82FAB
+:103CD0000E94761CCC2309F47CC0C13009F47DC05D
+:103CE00086E00E94C31C8FCE80910C02816080937D
+:103CF0000C0236CF80910C02816091CF8091070138
+:103D000087FD6FC010920B02809106019091070110
+:103D1000880F991F909307018093060180910802F4
+:103D200080FF09C08091080290910902019690934A
+:103D3000090280930802F894F999FECF1127E091C7
+:103D40000601F0910701C8E0D1E08091080290914E
+:103D50000902103091F40091570001700130D9F33D
+:103D600003E000935700E89500915700017001307F
+:103D7000D9F301E100935700E8950990199000915B
+:103D8000570001700130D9F301E000935700E89526
+:103D90001395103498F011270091570001700130ED
+:103DA000D9F305E000935700E895009157000170A2
+:103DB0000130D9F301E100935700E895329602975C
+:103DC00009F0C7CF103011F00296E5CF112484E13D
+:103DD00072CE8EE10E94C31C16CE84E90E94C31CE1
+:103DE00012CE81E080930B028FCF82E00E94C31C31
+:103DF0000ACE81E00E94C31C06CE80E10E94C31C53
+:103E000002CE84910E94A21C2091080230910902E6
+:103E1000E0910601F091070140CFCF930E94761CFC
+:103E2000C82F0E94A21CC13614F0C75503C0C0336E
+:103E30000CF0C0538C2F992787FD9095CF91089552
+:103E40000F931F930E940D1F082F112707FD109538
+:103E500002951295107F1027007F10270E940D1FDA
+:103E6000800F992787FD90951F910F910895CF930B
+:103E7000C82F85958595859585958A3034F0895A22
+:103E8000CF70CA3034F0C95A05C0805DCF70CA30D7
+:103E9000D4F7C05D0E94A21C8C2F0E94A21CCF915F
+:043EA0000895FFCFB3
+:023EA40080009C
+:0400000300003800C1
+:00000001FF
diff --git a/bootloaders/atmega/ATmegaBOOT_168_pro_8MHz.hex b/bootloaders/atmega/ATmegaBOOT_168_pro_8MHz.hex
new file mode 100644
index 0000000..994e478
--- /dev/null
+++ b/bootloaders/atmega/ATmegaBOOT_168_pro_8MHz.hex
@@ -0,0 +1,126 @@
+:103800000C94341C0C94511C0C94511C0C94511CA1
+:103810000C94511C0C94511C0C94511C0C94511C74
+:103820000C94511C0C94511C0C94511C0C94511C64
+:103830000C94511C0C94511C0C94511C0C94511C54
+:103840000C94511C0C94511C0C94511C0C94511C44
+:103850000C94511C0C94511C0C94511C0C94511C34
+:103860000C94511C0C94511C11241FBECFEFD4E0BA
+:10387000DEBFCDBF11E0A0E0B1E0EEEAFFE302C0A1
+:1038800005900D92A230B107D9F712E0A2E0B1E0A5
+:1038900001C01D92AD30B107E1F70E94331D0C94B9
+:1038A000D51F0C94001C982F9595959595959595F9
+:1038B000905D8F708A307CF0282F295A8091C0004B
+:1038C00085FFFCCF9093C6008091C00085FFFCCFA0
+:1038D0002093C6000895282F205DF0CF982F809167
+:1038E000C00085FFFCCF9093C6000895EF92FF9231
+:1038F0000F931F93EE24FF2487018091C00087FD62
+:1039000017C00894E11CF11C011D111D81E2E8168D
+:1039100081EAF80687E0080780E0180770F3E09175
+:103920000401F091050109958091C00087FFE9CF5E
+:103930008091C6001F910F91FF90EF9008950E9413
+:10394000761C982F8091C00085FFFCCF9093C60015
+:1039500091362CF490330CF09053892F089597559D
+:10396000892F08951F930E949F1C182F0E949F1C4F
+:103970001295107F810F1F9108951F93182F882390
+:1039800021F00E94761C1150E1F71F9108951F93BA
+:10399000182F0E94761C803249F0809103018F5FBE
+:1039A000809303018530C1F01F9108958091C0007C
+:1039B00085FFFCCF84E18093C6008091C00085FF25
+:1039C000FCCF1093C6008091C00085FFFCCF80E142
+:1039D0008093C6001F910895E0910401F0910501C4
+:1039E00009951F9108950E94761C803241F08091C4
+:1039F00003018F5F80930301853081F008958091EA
+:103A0000C00085FFFCCF84E18093C6008091C00098
+:103A100085FFFCCF80E18093C6000895E09104010A
+:103A2000F09105010995089510920A028823D1F0BA
+:103A300090E048EC50E02D9A28EE33E0FA013197FF
+:103A4000F1F721503040D1F72D9828EE33E0FA01FC
+:103A50003197F1F721503040D1F79F5F981758F315
+:103A600080930A0208953F924F925F926F927F92E5
+:103A70008F929F92AF92BF92CF92DF92EF92FF927E
+:103A80000F931F93CF93DF9394B714BE8091600080
+:103A90008861809360001092600091FF0CC289E100
+:103AA0008093C4001092C50088E18093C10086E035
+:103AB0008093C2005098589A259A81E00E94141D64
+:103AC00044E1F42E3EE1E32E24E9D22E96E0C92E05
+:103AD00080E1B82EAA24A39401E4902E16E5812E4D
+:103AE000B2E57B2EA0E26A2EF9E45F2EE3E54E2ECE
+:103AF00070E5372E0E94761C8033B9F18133C1F115
+:103B0000803409F470C0813409F477C0823409F438
+:103B100086C0853409F489C0803539F1823529F1B0
+:103B2000813509F4AFC1853509F485C0863509F4BE
+:103B30008DC0843609F435C1843709F4C1C0853796
+:103B400009F490C0863709F466C0809103018F5F45
+:103B500080930301853071F6E0910401F091050135
+:103B600009950E94761C803349F60E94F31CC2CF4F
+:103B70000E94761C803249F78091C00085FFFCCFFF
+:103B8000F092C6008091C00085FFFCCF9092C600E5
+:103B90008091C00085FFFCCF8092C6008091C0005C
+:103BA00085FFFCCF7092C6008091C00085FFFCCFDE
+:103BB0006092C6008091C00085FFFCCF5092C60085
+:103BC0008091C00085FFFCCF4092C6008091C0006C
+:103BD00085FFFCCF3092C6008091C00085FFFCCFEE
+:103BE000B092C60087CF0E94761C863808F4BDCFFD
+:103BF0000E94761C0E94F31C7DCF0E94761C8038A8
+:103C000009F45AC0813809F453C0823809F440C11C
+:103C1000883909F449C080E00E94C71C6BCF84E159
+:103C20000E94BD1C0E94F31C65CF85E00E94BD1C54
+:103C30000E94F31C5FCF0E94761C809306010E94B5
+:103C4000761C809307010E94F31C54CF0E94761CBF
+:103C5000803309F421C183E00E94BD1C80E00E94F2
+:103C6000C71C48CF0E94761C803209F06ECF80912D
+:103C7000C00085FFFCCFF092C6008091C00085FF98
+:103C8000FCCFE092C6008091C00085FFFCCFD092AF
+:103C9000C6008091C00085FFFCCFC092C600809115
+:103CA000C00085FFFCCF9CCF83E00E94C71C22CFC1
+:103CB00081E00E94C71C1ECF82E00E94C71C1ACF61
+:103CC0000E94761C809309020E94761C8093080251
+:103CD0008091060190910701880F991F9093070129
+:103CE000809306010E94761C853409F4C5C080913A
+:103CF0000C028E7F80930C020E94761C803209F0A9
+:103D0000F9CE8091C00085FFFCCFF092C600609193
+:103D10000802709109026115710591F140E050E0CF
+:103D200080910C02A82FA170B82FB27010C0BB23D5
+:103D300061F1E0910601F09107013196F0930701DE
+:103D4000E09306014F5F5F4F46175707C8F4AA2359
+:103D500071F3F999FECF209106013091070132BD30
+:103D600021BDF89A90B58091C00085FFFCCF90935B
+:103D7000C6002F5F3F4F3093070120930601E2CF2B
+:103D80008091C00085FFFCCF2BCFE0910601F09120
+:103D9000070194918091C00085FFFCCF9093C600ED
+:103DA000CCCF0E94761C809309020E94761C8093DF
+:103DB000080280910C028E7F80930C020E94761C78
+:103DC000853429F480910C02816080930C028091EB
+:103DD000080290910902892B89F000E010E00E940E
+:103DE000761CF801E85FFE4F80830F5F1F4F8091C4
+:103DF0000802909109020817190788F30E94761C9F
+:103E0000803209F0A2CE80910C0280FF62C0409106
+:103E1000060150910701440F551F5093070140932D
+:103E20000601609108027091090261157105C9F0DF
+:103E3000E8E0F1E09A01DB01AE0FBF1FF999FECF78
+:103E400032BD21BD819180BDFA9AF99A2F5F3F4F13
+:103E5000EA17FB0799F7460F571F50930701409346
+:103E600006018091C00085FFFCCFF092C6008091D2
+:103E7000C00085FFFCCFB4CE80910C02816080939E
+:103E80000C023ACF0E94F31C88E080936000FFCFC1
+:103E900080E10E94C71C2ECE0E94761C0E94761CD8
+:103EA000182F0E94761C112381F0113051F086E00A
+:103EB0000E94C71C1FCEE0910401F09105010995F5
+:103EC000EECD84E90E94C71C15CE8EE10E94C71C6E
+:103ED00011CE809107018823880F880B8A21809357
+:103EE0000B028091060190910701880F991F909312
+:103EF0000701809306018091080280FF09C080912C
+:103F00000802909109020196909309028093080299
+:103F1000F894F999FECF1127E0910601F09107017D
+:103F2000C8E0D1E08091080290910902103091F42C
+:103F30000091570001700130D9F303E0009357005E
+:103F4000E8950091570001700130D9F301E1009329
+:103F50005700E895099019900091570001700130C1
+:103F6000D9F301E000935700E8951395103498F0C9
+:103F700011270091570001700130D9F305E000933B
+:103F80005700E8950091570001700130D9F301E125
+:103F900000935700E8953296029709F0C7CF10308A
+:0E3FA00011F00296E5CF11245CCFF894FFCF0C
+:023FAE00800091
+:0400000300003800C1
+:00000001FF
diff --git a/bootloaders/atmega/Makefile b/bootloaders/atmega/Makefile
new file mode 100755
index 0000000..0fd54db
--- /dev/null
+++ b/bootloaders/atmega/Makefile
@@ -0,0 +1,224 @@
+# Makefile for ATmegaBOOT
+# E.Lins, 18.7.2005
+# $Id$
+#
+# Instructions
+#
+# To make bootloader .hex file:
+# make diecimila
+# make lilypad
+# make ng
+# etc...
+#
+# To burn bootloader .hex file:
+# make diecimila_isp
+# make lilypad_isp
+# make ng_isp
+# etc...
+
+# program name should not be changed...
+PROGRAM    = ATmegaBOOT_168
+
+# enter the parameters for the avrdude isp tool
+ISPTOOL	   = stk500v2
+ISPPORT	   = usb
+ISPSPEED   = -b 115200
+
+MCU_TARGET = atmega168
+LDSECTION  = --section-start=.text=0x3800
+
+# the efuse should really be 0xf8; since, however, only the lower
+# three bits of that byte are used on the atmega168, avrdude gets
+# confused if you specify 1's for the higher bits, see:
+# http://tinker.it/now/2007/02/24/the-tale-of-avrdude-atmega168-and-extended-bits-fuses/
+#
+# similarly, the lock bits should be 0xff instead of 0x3f (to
+# unlock the bootloader section) and 0xcf instead of 0x0f (to
+# lock it), but since the high two bits of the lock byte are
+# unused, avrdude would get confused.
+
+ISPFUSES    = avrdude -c $(ISPTOOL) -p $(MCU_TARGET) -P $(ISPPORT) $(ISPSPEED) \
+-e -u -U lock:w:0x3f:m -U efuse:w:0x$(EFUSE):m -U hfuse:w:0x$(HFUSE):m -U lfuse:w:0x$(LFUSE):m
+ISPFLASH    = avrdude -c $(ISPTOOL) -p $(MCU_TARGET) -P $(ISPPORT) $(ISPSPEED) \
+-U flash:w:$(PROGRAM)_$(TARGET).hex -U lock:w:0x0f:m
+
+STK500 = "C:\Program Files\Atmel\AVR Tools\STK500\Stk500.exe"
+STK500-1 = $(STK500) -e -d$(MCU_TARGET) -pf -vf -if$(PROGRAM)_$(TARGET).hex \
+-lFF -LFF -f$(HFUSE)$(LFUSE) -EF8 -ms -q -cUSB -I200kHz -s -wt
+STK500-2 = $(STK500) -d$(MCU_TARGET) -ms -q -lCF -LCF -cUSB -I200kHz -s -wt
+
+
+OBJ        = $(PROGRAM).o
+OPTIMIZE   = -O2
+
+DEFS       = 
+LIBS       =
+
+CC         = avr-gcc
+
+# Override is only needed by avr-lib build system.
+
+override CFLAGS        = -g -Wall $(OPTIMIZE) -mmcu=$(MCU_TARGET) -DF_CPU=$(AVR_FREQ) $(DEFS)
+override LDFLAGS       = -Wl,$(LDSECTION)
+#override LDFLAGS       = -Wl,-Map,$(PROGRAM).map,$(LDSECTION)
+
+OBJCOPY        = avr-objcopy
+OBJDUMP        = avr-objdump
+
+all:
+
+lilypad: TARGET = lilypad
+lilypad: CFLAGS += '-DMAX_TIME_COUNT=F_CPU>>1' '-DNUM_LED_FLASHES=3'
+lilypad: AVR_FREQ = 8000000L
+lilypad: $(PROGRAM)_lilypad.hex
+
+lilypad_isp: lilypad
+lilypad_isp: TARGET = lilypad
+lilypad_isp: HFUSE = DD
+lilypad_isp: LFUSE = E2
+lilypad_isp: EFUSE = 00
+lilypad_isp: isp
+
+lilypad_resonator: TARGET = lilypad_resonator
+lilypad_resonator: CFLAGS += '-DMAX_TIME_COUNT=F_CPU>>4' '-DNUM_LED_FLASHES=3'
+lilypad_resonator: AVR_FREQ = 8000000L
+lilypad_resonator: $(PROGRAM)_lilypad_resonator.hex
+
+lilypad_resonator_isp: lilypad_resonator
+lilypad_resonator_isp: TARGET = lilypad_resonator
+lilypad_resonator_isp: HFUSE = DD
+lilypad_resonator_isp: LFUSE = C6
+lilypad_resonator_isp: EFUSE = 00
+lilypad_resonator_isp: isp
+
+pro8: TARGET = pro_8MHz
+pro8: CFLAGS += '-DMAX_TIME_COUNT=F_CPU>>4' '-DNUM_LED_FLASHES=1' '-DWATCHDOG_MODS'
+pro8: AVR_FREQ = 8000000L
+pro8: $(PROGRAM)_pro_8MHz.hex
+
+pro8_isp: pro8
+pro8_isp: TARGET = pro_8MHz
+pro8_isp: HFUSE = DD
+pro8_isp: LFUSE = C6
+pro8_isp: EFUSE = 00
+pro8_isp: isp
+
+pro16: TARGET = pro_16MHz
+pro16: CFLAGS += '-DMAX_TIME_COUNT=F_CPU>>4' '-DNUM_LED_FLASHES=1' '-DWATCHDOG_MODS'
+pro16: AVR_FREQ = 16000000L
+pro16: $(PROGRAM)_pro_16MHz.hex
+
+pro16_isp: pro16
+pro16_isp: TARGET = pro_16MHz
+pro16_isp: HFUSE = DD
+pro16_isp: LFUSE = C6
+pro16_isp: EFUSE = 00
+pro16_isp: isp
+
+pro20: TARGET = pro_20mhz
+pro20: CFLAGS += '-DMAX_TIME_COUNT=F_CPU>>4' '-DNUM_LED_FLASHES=1' '-DWATCHDOG_MODS'
+pro20: AVR_FREQ = 20000000L
+pro20: $(PROGRAM)_pro_20mhz.hex
+
+pro20_isp: pro20
+pro20_isp: TARGET = pro_20mhz
+pro20_isp: HFUSE = DD
+pro20_isp: LFUSE = C6
+pro20_isp: EFUSE = 00
+pro20_isp: isp
+
+diecimila: TARGET = diecimila
+diecimila: CFLAGS += '-DMAX_TIME_COUNT=F_CPU>>4' '-DNUM_LED_FLASHES=1'
+diecimila: AVR_FREQ = 16000000L 
+diecimila: $(PROGRAM)_diecimila.hex
+
+diecimila_isp: diecimila
+diecimila_isp: TARGET = diecimila
+diecimila_isp: HFUSE = DD
+diecimila_isp: LFUSE = FF
+diecimila_isp: EFUSE = 00
+diecimila_isp: isp
+
+ng: TARGET = ng
+ng: CFLAGS += '-DMAX_TIME_COUNT=F_CPU>>1' '-DNUM_LED_FLASHES=3'
+ng: AVR_FREQ = 16000000L
+ng: $(PROGRAM)_ng.hex
+
+ng_isp: ng
+ng_isp: TARGET = ng
+ng_isp: HFUSE = DD
+ng_isp: LFUSE = FF
+ng_isp: EFUSE = 00
+ng_isp: isp
+
+atmega328: TARGET = atmega328
+atmega328: MCU_TARGET = atmega328p
+atmega328: CFLAGS += '-DMAX_TIME_COUNT=F_CPU>>4' '-DNUM_LED_FLASHES=1' -DBAUD_RATE=57600
+atmega328: AVR_FREQ = 16000000L 
+atmega328: LDSECTION  = --section-start=.text=0x7800
+atmega328: $(PROGRAM)_atmega328.hex
+
+atmega328_isp: atmega328
+atmega328_isp: TARGET = atmega328
+atmega328_isp: MCU_TARGET = atmega328p
+atmega328_isp: HFUSE = DA
+atmega328_isp: LFUSE = FF
+atmega328_isp: EFUSE = 05
+atmega328_isp: isp
+
+atmega328_pro8: TARGET = atmega328_pro_8MHz
+atmega328_pro8: MCU_TARGET = atmega328p
+atmega328_pro8: CFLAGS += '-DMAX_TIME_COUNT=F_CPU>>4' '-DNUM_LED_FLASHES=1' -DBAUD_RATE=57600 -DDOUBLE_SPEED
+atmega328_pro8: AVR_FREQ = 8000000L 
+atmega328_pro8: LDSECTION  = --section-start=.text=0x7800
+atmega328_pro8: $(PROGRAM)_atmega328_pro_8MHz.hex
+
+atmega328_pro8_isp: atmega328_pro8
+atmega328_pro8_isp: TARGET = atmega328_pro_8MHz
+atmega328_pro8_isp: MCU_TARGET = atmega328p
+atmega328_pro8_isp: HFUSE = DA
+atmega328_pro8_isp: LFUSE = FF
+atmega328_pro8_isp: EFUSE = 05
+atmega328_pro8_isp: isp
+
+mega: TARGET = atmega1280
+mega: MCU_TARGET = atmega1280
+mega: CFLAGS += '-DMAX_TIME_COUNT=F_CPU>>4' '-DNUM_LED_FLASHES=0' -DBAUD_RATE=57600
+mega: AVR_FREQ = 16000000L 
+mega: LDSECTION  = --section-start=.text=0x1F000
+mega: $(PROGRAM)_atmega1280.hex
+
+mega_isp: mega
+mega_isp: TARGET = atmega1280
+mega_isp: MCU_TARGET = atmega1280
+mega_isp: HFUSE = DA
+mega_isp: LFUSE = FF
+mega_isp: EFUSE = F5
+mega_isp: isp
+
+isp: $(TARGET)
+	$(ISPFUSES)
+	$(ISPFLASH)
+
+isp-stk500: $(PROGRAM)_$(TARGET).hex
+	$(STK500-1)
+	$(STK500-2)
+
+%.elf: $(OBJ)
+	$(CC) $(CFLAGS) $(LDFLAGS) -o $@ $^ $(LIBS)
+
+clean:
+	rm -rf *.o *.elf *.lst *.map *.sym *.lss *.eep *.srec *.bin *.hex
+
+%.lst: %.elf
+	$(OBJDUMP) -h -S $< > $@
+
+%.hex: %.elf
+	$(OBJCOPY) -j .text -j .data -O ihex $< $@
+
+%.srec: %.elf
+	$(OBJCOPY) -j .text -j .data -O srec $< $@
+
+%.bin: %.elf
+	$(OBJCOPY) -j .text -j .data -O binary $< $@
+	
diff --git a/bootloaders/atmega8/ATmegaBOOT.c b/bootloaders/atmega8/ATmegaBOOT.c
new file mode 100755
index 0000000..17977e6
--- /dev/null
+++ b/bootloaders/atmega8/ATmegaBOOT.c
@@ -0,0 +1,507 @@
+/**********************************************************/
+/* Serial Bootloader for Atmel mega8 AVR Controller       */
+/*                                                        */
+/* ATmegaBOOT.c                                           */
+/*                                                        */
+/* Copyright (c) 2003, Jason P. Kyle                      */
+/*                                                        */
+/* Hacked by DojoCorp - ZGZ - MMX - IVR                   */
+/* Hacked by David A. Mellis                              */
+/*                                                        */
+/* This program is free software; you can redistribute it */
+/* and/or modify it under the terms of the GNU General    */
+/* Public License as published by the Free Software       */
+/* Foundation; either version 2 of the License, or        */
+/* (at your option) any later version.                    */
+/*                                                        */
+/* This program is distributed in the hope that it will   */
+/* be useful, but WITHOUT ANY WARRANTY; without even the  */
+/* implied warranty of MERCHANTABILITY or FITNESS FOR A   */
+/* PARTICULAR PURPOSE.  See the GNU General Public        */
+/* License for more details.                              */
+/*                                                        */
+/* You should have received a copy of the GNU General     */
+/* Public License along with this program; if not, write  */
+/* to the Free Software Foundation, Inc.,                 */
+/* 59 Temple Place, Suite 330, Boston, MA  02111-1307 USA */
+/*                                                        */
+/* Licence can be viewed at                               */
+/* http://www.fsf.org/licenses/gpl.txt                    */
+/*                                                        */
+/* Target = Atmel AVR m8                                  */
+/**********************************************************/
+
+#include <inttypes.h>
+#include <avr/io.h>
+#include <avr/pgmspace.h>
+#include <avr/eeprom.h>
+#include <avr/interrupt.h>
+#include <avr/delay.h>
+
+//#define F_CPU			16000000
+
+/* We, Malmoitians, like slow interaction
+ * therefore the slow baud rate ;-)
+ */
+//#define BAUD_RATE		9600
+
+/* 6.000.000 is more or less 8 seconds at the
+ * speed configured here
+ */
+//#define MAX_TIME_COUNT	6000000
+#define MAX_TIME_COUNT (F_CPU>>1)
+///#define MAX_TIME_COUNT_MORATORY	1600000
+
+/* SW_MAJOR and MINOR needs to be updated from time to time to avoid warning message from AVR Studio */
+#define HW_VER	 0x02
+#define SW_MAJOR 0x01
+#define SW_MINOR 0x12
+
+// AVR-GCC compiler compatibility
+// avr-gcc compiler v3.1.x and older doesn't support outb() and inb()
+//      if necessary, convert outb and inb to outp and inp
+#ifndef outb
+	#define outb(sfr,val)  (_SFR_BYTE(sfr) = (val))
+#endif
+#ifndef inb
+	#define inb(sfr) _SFR_BYTE(sfr)
+#endif
+
+/* defines for future compatibility */
+#ifndef cbi
+	#define cbi(sfr, bit) (_SFR_BYTE(sfr) &= ~_BV(bit))
+#endif
+#ifndef sbi
+	#define sbi(sfr, bit) (_SFR_BYTE(sfr) |= _BV(bit))
+#endif
+
+/* Adjust to suit whatever pin your hardware uses to enter the bootloader */
+#define eeprom_rb(addr)   eeprom_read_byte ((uint8_t *)(addr))
+#define eeprom_rw(addr)   eeprom_read_word ((uint16_t *)(addr))
+#define eeprom_wb(addr, val)   eeprom_write_byte ((uint8_t *)(addr), (uint8_t)(val))
+
+/* Onboard LED is connected to pin PB5 */
+#define LED_DDR  DDRB
+#define LED_PORT PORTB
+#define LED_PIN  PINB
+#define LED      PINB5
+
+
+#define SIG1	0x1E	// Yep, Atmel is the only manufacturer of AVR micros.  Single source :(
+#define SIG2	0x93
+#define SIG3	0x07
+#define PAGE_SIZE	0x20U	//32 words
+
+
+void putch(char);
+char getch(void);
+void getNch(uint8_t);
+void byte_response(uint8_t);
+void nothing_response(void);
+
+union address_union {
+  uint16_t word;
+  uint8_t  byte[2];
+} address;
+
+union length_union {
+  uint16_t word;
+  uint8_t  byte[2];
+} length;
+
+struct flags_struct {
+  unsigned eeprom : 1;
+  unsigned rampz  : 1;
+} flags;
+
+uint8_t buff[256];
+//uint8_t address_high;
+
+uint8_t pagesz=0x80;
+
+uint8_t i;
+//uint8_t bootuart0=0,bootuart1=0;
+
+
+void (*app_start)(void) = 0x0000;
+
+int main(void)
+{
+  uint8_t ch,ch2;
+  uint16_t w;
+
+  //cbi(BL_DDR,BL);
+  //sbi(BL_PORT,BL);
+
+  asm volatile("nop\n\t");
+
+  /* check if flash is programmed already, if not start bootloader anyway */
+  //if(pgm_read_byte_near(0x0000) != 0xFF) {
+
+    /* check if bootloader pin is set low */
+    //if(bit_is_set(BL_PIN,BL)) app_start();
+  //}
+
+  /* initialize UART(s) depending on CPU defined */
+  /* m8 */
+  UBRRH = (((F_CPU/BAUD_RATE)/16)-1)>>8; 	// set baud rate
+  UBRRL = (((F_CPU/BAUD_RATE)/16)-1);
+  UCSRB = (1<<RXEN)|(1<<TXEN);  // enable Rx & Tx
+  UCSRC = (1<<URSEL)|(1<<UCSZ1)|(1<<UCSZ0);  // config USART; 8N1
+
+  //UBRRL = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
+  //UBRRH = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
+  //UCSRA = 0x00;
+  //UCSRC = 0x86;
+  //UCSRB = _BV(TXEN)|_BV(RXEN);
+
+
+  /* this was giving uisp problems, so I removed it; without it, the boot
+     works on with uisp and avrdude on the mac (at least). */
+  //putch('\0');
+
+  //uint32_t l;
+  //uint32_t time_count;
+  //time_count=0;
+
+  /* set LED pin as output */
+  sbi(LED_DDR,LED);
+	for (i = 0; i < 16; i++) {
+		outb(LED_PORT, inb(LED_PORT) ^ _BV(LED));
+		_delay_loop_2(0);
+	}
+	
+	//for (l=0; l<40000000; l++)
+		//outb(LED_PORT, inb(LED_PORT) ^= _BV(LED));
+
+  /* flash onboard LED three times to signal entering of bootloader */
+  //for(i=0; i<3; ++i) {
+    //for(l=0; l<40000000; ++l);
+    //sbi(LED_PORT,LED);
+    //for(l=0; l<40000000; ++l);
+    //cbi(LED_PORT,LED);
+  //}
+
+ /* see comment at previous call to putch() */
+ //putch('\0'); // this line is needed for the synchronization of the programmer
+
+  /* forever */
+  for (;;) {
+    //if((inb(UCSRA) & _BV(RXC))){
+    /* get character from UART */
+		ch = getch();
+		
+		/* A bunch of if...else if... gives smaller code than switch...case ! */
+	
+		/* Hello is anyone home ? */ 
+		if(ch=='0') {
+		  nothing_response();
+		}
+	
+		/* Request programmer ID */
+		/* Not using PROGMEM string due to boot block in m128 being beyond 64kB boundry  */
+		/* Would need to selectively manipulate RAMPZ, and it's only 9 characters anyway so who cares.  */
+		else if(ch=='1') {
+			if (getch() == ' ') {
+				putch(0x14);
+				putch('A');
+				putch('V');
+				putch('R');
+				putch(' ');
+				putch('I');
+				putch('S');
+				putch('P');
+				putch(0x10);
+		  }
+		}
+	
+		/* AVR ISP/STK500 board commands  DON'T CARE so default nothing_response */
+		else if(ch=='@') {
+		  ch2 = getch();
+		  if (ch2>0x85) getch();
+		  nothing_response();
+		}
+	
+		/* AVR ISP/STK500 board requests */
+		else if(ch=='A') {
+		  ch2 = getch();
+		  if(ch2==0x80) byte_response(HW_VER);		// Hardware version
+		  else if(ch2==0x81) byte_response(SW_MAJOR);	// Software major version
+		  else if(ch2==0x82) byte_response(SW_MINOR);	// Software minor version
+		  //else if(ch2==0x98) byte_response(0x03);		// Unknown but seems to be required by avr studio 3.56
+		  else byte_response(0x00);				// Covers various unnecessary responses we don't care about
+		}
+	
+		/* Device Parameters  DON'T CARE, DEVICE IS FIXED  */
+		else if(ch=='B') {
+		  getNch(20);
+		  nothing_response();
+		}
+	
+		/* Parallel programming stuff  DON'T CARE  */
+		else if(ch=='E') {
+		  getNch(5);
+		  nothing_response();
+		}
+	
+		/* Enter programming mode  */
+		else if(ch=='P') {
+		  nothing_response();
+		  // FIXME: modified only here by DojoCorp, Mumbai, India, 20050626
+		  //time_count=0; // exted the delay once entered prog.mode
+		}
+	
+		/* Leave programming mode  */
+		else if(ch=='Q') {
+		  nothing_response();
+		  //time_count=MAX_TIME_COUNT_MORATORY; 	// once the programming is done, 
+												// we should start the application
+												// but uisp has problems with this,
+												// therefore we just change the times
+												// and give the programmer 1 sec to react
+		}
+	
+		/* Erase device, don't care as we will erase one page at a time anyway.  */
+		else if(ch=='R') {
+		  nothing_response();
+		}
+	
+		/* Set address, little endian. EEPROM in bytes, FLASH in words  */
+		/* Perhaps extra address bytes may be added in future to support > 128kB FLASH.  */
+		/* This might explain why little endian was used here, big endian used everywhere else.  */
+		else if(ch=='U') {
+		  address.byte[0] = getch();
+		  address.byte[1] = getch();
+		  nothing_response();
+		}
+	
+		/* Universal SPI programming command, disabled.  Would be used for fuses and lock bits.  */
+		else if(ch=='V') {
+		  getNch(4);
+		  byte_response(0x00);
+		}
+	
+		/* Write memory, length is big endian and is in bytes  */
+		else if(ch=='d') {
+		  length.byte[1] = getch();
+		  length.byte[0] = getch();
+		  flags.eeprom = 0;
+		  if (getch() == 'E') flags.eeprom = 1;
+		  for (w=0;w<length.word;w++) {
+		    buff[w] = getch();	                        // Store data in buffer, can't keep up with serial data stream whilst programming pages
+		  }
+		  if (getch() == ' ') {
+				if (flags.eeprom) {		                //Write to EEPROM one byte at a time
+					for(w=0;w<length.word;w++) {
+						eeprom_wb(address.word,buff[w]);
+						address.word++;
+					}			
+				} else {					        //Write to FLASH one page at a time
+					//if (address.byte[1]>127) address_high = 0x01;	//Only possible with m128, m256 will need 3rd address byte. FIXME
+					//else address_high = 0x00;
+			
+					//address.word = address.word << 1;	        //address * 2 -> byte location
+					//if ((length.byte[0] & 0x01)) length.word++;	//Even up an odd number of bytes
+					cli();					//Disable interrupts, just to be sure
+					while(bit_is_set(EECR,EEWE));			//Wait for previous EEPROM writes to complete
+					asm volatile(
+							 "clr	r17		\n\t"	//page_word_count
+							 "lds	r30,address	\n\t"	//Address of FLASH location (in words)
+							 "lds	r31,address+1	\n\t"
+							 "lsl r30				\n\t"  //address * 2 -> byte location
+							 "rol r31				\n\t" 
+							 "ldi	r28,lo8(buff)	\n\t"	//Start of buffer array in RAM
+							 "ldi	r29,hi8(buff)	\n\t"
+							 "lds	r24,length	\n\t"	//Length of data to be written (in bytes)
+							 "lds	r25,length+1	\n\t"
+							 "sbrs r24,0		\n\t"  //Even up an odd number of bytes
+							 "rjmp length_loop		\n\t"
+							 "adiw r24,1		\n\t"
+							 "length_loop:		\n\t"	//Main loop, repeat for number of words in block							 							 
+							 "cpi	r17,0x00	\n\t"	//If page_word_count=0 then erase page
+							 "brne	no_page_erase	\n\t"						 
+							 "rcall  wait_spm		\n\t"
+//							 "wait_spm1:		\n\t"
+//							 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+//							 "andi	r16,1           \n\t"
+//							 "cpi	r16,1           \n\t"
+//							 "breq	wait_spm1       \n\t"
+							 "ldi	r16,0x03	\n\t"	//Erase page pointed to by Z
+							 "sts	%0,r16		\n\t"
+							 "spm			\n\t"							 
+							 "rcall  wait_spm		\n\t"
+//							 "wait_spm2:		\n\t"
+//							 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+//							 "andi	r16,1           \n\t"
+//							 "cpi	r16,1           \n\t"
+//							 "breq	wait_spm2       \n\t"									 
+							 "ldi	r16,0x11	\n\t"	//Re-enable RWW section
+							 "sts	%0,r16		\n\t"						 			 
+							 "spm			\n\t"
+							 "no_page_erase:		\n\t"							 
+							 "ld	r0,Y+		\n\t"	//Write 2 bytes into page buffer
+							 "ld	r1,Y+		\n\t"							 
+										 
+							 "rcall  wait_spm		\n\t"
+//							 "wait_spm3:		\n\t"
+//							 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+//							 "andi	r16,1           \n\t"
+//							 "cpi	r16,1           \n\t"
+//							 "breq	wait_spm3       \n\t"
+							 "ldi	r16,0x01	\n\t"	//Load r0,r1 into FLASH page buffer
+							 "sts	%0,r16		\n\t"
+							 "spm			\n\t"
+										 
+							 "inc	r17		\n\t"	//page_word_count++
+							 "cpi r17,%1	        \n\t"
+							 "brlo	same_page	\n\t"	//Still same page in FLASH
+							 "write_page:		\n\t"
+							 "clr	r17		\n\t"	//New page, write current one first
+							 "rcall  wait_spm		\n\t"
+//							 "wait_spm4:		\n\t"
+//							 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+//							 "andi	r16,1           \n\t"
+//							 "cpi	r16,1           \n\t"
+//							 "breq	wait_spm4       \n\t"
+							 "ldi	r16,0x05	\n\t"	//Write page pointed to by Z
+							 "sts	%0,r16		\n\t"
+							 "spm			\n\t"
+							 "rcall  wait_spm		\n\t"
+//							 "wait_spm5:		\n\t"
+//							 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+//							 "andi	r16,1           \n\t"
+//							 "cpi	r16,1           \n\t"
+//							 "breq	wait_spm5       \n\t"									 
+							 "ldi	r16,0x11	\n\t"	//Re-enable RWW section
+							 "sts	%0,r16		\n\t"						 			 
+							 "spm			\n\t"					 		 
+							 "same_page:		\n\t"							 
+							 "adiw	r30,2		\n\t"	//Next word in FLASH
+							 "sbiw	r24,2		\n\t"	//length-2
+							 "breq	final_write	\n\t"	//Finished
+							 "rjmp	length_loop	\n\t"
+							 
+							 "wait_spm:  \n\t"
+							 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+							 "andi	r16,1           \n\t"
+							 "cpi	r16,1           \n\t"
+							 "breq	wait_spm       \n\t"
+							 "ret			\n\t"
+							 
+							 "final_write:		\n\t"
+							 "cpi	r17,0		\n\t"
+							 "breq	block_done	\n\t"
+							 "adiw	r24,2		\n\t"	//length+2, fool above check on length after short page write
+							 "rjmp	write_page	\n\t"
+							 "block_done:		\n\t"
+							 "clr	__zero_reg__	\n\t"	//restore zero register
+							 : "=m" (SPMCR) : "M" (PAGE_SIZE) : "r0","r16","r17","r24","r25","r28","r29","r30","r31");
+			
+					/* Should really add a wait for RWW section to be enabled, don't actually need it since we never */
+					/* exit the bootloader without a power cycle anyhow */
+				}
+				putch(0x14);
+				putch(0x10);
+			}		
+		}
+	
+		/* Read memory block mode, length is big endian.  */
+		else if(ch=='t') {
+		  length.byte[1] = getch();
+		  length.byte[0] = getch();
+		  if (getch() == 'E') flags.eeprom = 1;
+		  else {
+				flags.eeprom = 0;
+				address.word = address.word << 1;	        // address * 2 -> byte location
+		  }
+		  if (getch() == ' ') {		                // Command terminator
+				putch(0x14);
+				for (w=0;w < length.word;w++) {		        // Can handle odd and even lengths okay
+					if (flags.eeprom) {	                        // Byte access EEPROM read
+						putch(eeprom_rb(address.word));
+						address.word++;
+					} else {	
+						if (!flags.rampz) putch(pgm_read_byte_near(address.word));
+						address.word++;
+					}
+				}
+				putch(0x10);
+		  }
+		}
+	
+		/* Get device signature bytes  */
+		else if(ch=='u') {
+		  if (getch() == ' ') {
+				putch(0x14);
+				putch(SIG1);
+				putch(SIG2);
+				putch(SIG3);
+				putch(0x10);
+		  }
+		}
+	
+		/* Read oscillator calibration byte */
+		else if(ch=='v') {
+		  byte_response(0x00);
+		}
+//    } else {
+//			time_count++;
+//			if (time_count>=MAX_TIME_COUNT) {
+//				app_start();
+//			}
+//		}
+	} /* end of forever loop */
+}
+
+void putch(char ch)
+{
+  /* m8 */
+  while (!(inb(UCSRA) & _BV(UDRE)));
+  outb(UDR,ch);
+}
+
+char getch(void)
+{
+  /* m8 */
+	uint32_t count = 0;
+  while(!(inb(UCSRA) & _BV(RXC))) {
+		/* HACKME:: here is a good place to count times*/
+		count++;
+		if (count > MAX_TIME_COUNT)
+			app_start();
+  }
+  return (inb(UDR));
+}
+
+void getNch(uint8_t count)
+{
+  uint8_t i;
+  for(i=0;i<count;i++) {
+    /* m8 */
+    //while(!(inb(UCSRA) & _BV(RXC)));
+    //inb(UDR);
+		getch(); // need to handle time out
+  }
+}
+
+void byte_response(uint8_t val)
+{
+  if (getch() == ' ') {
+    putch(0x14);
+    putch(val);
+    putch(0x10);
+  }
+}
+
+void nothing_response(void)
+{
+  if (getch() == ' ') {
+    putch(0x14);
+    putch(0x10);
+  }
+}
+
+/* end of file ATmegaBOOT.c */
+
+
+
diff --git a/bootloaders/atmega8/ATmegaBOOT.hex b/bootloaders/atmega8/ATmegaBOOT.hex
new file mode 100644
index 0000000..6190d48
--- /dev/null
+++ b/bootloaders/atmega8/ATmegaBOOT.hex
@@ -0,0 +1,66 @@
+:101C000012C02BC02AC029C028C027C026C025C0AA
+:101C100024C023C022C021C020C01FC01EC01DC0C0
+:101C20001CC01BC01AC011241FBECFE5D4E0DEBF0C
+:101C3000CDBF10E0A0E6B0E0E8EEFFE102C0059005
+:101C40000D92A236B107D9F711E0A2E6B0E001C0CB
+:101C50001D92AA36B107E1F74FC0D2CFEF92FF92A3
+:101C60000F931F93EE24FF24870113C00894E11CF7
+:101C7000F11C011D111D81E0E81682E1F8068AE7DA
+:101C8000080780E0180728F0E0916200F0916300F7
+:101C900009955F9BEBCF8CB1992787FD90951F919C
+:101CA0000F91FF90EF9008955D9BFECF8CB9089542
+:101CB000D5DF803221F484E1F7DF80E1F5DF08959C
+:101CC0001F93182FCBDF803231F484E1EDDF812FB9
+:101CD000EBDF80E1E9DF1F9108951F93CF93DF933E
+:101CE000182FC0E0D0E002C0B9DF2196C117E0F3A1
+:101CF000DF91CF911F910895CFE5D4E0DEBFCDBF36
+:101D0000000010BC83E389B988E18AB986E880BD08
+:101D1000BD9A1092680130E2E0E0F0E02FE088B375
+:101D2000832788BBCF010197F1F7215027FFF7CF19
+:101D300020E12093680192DF803381F1813399F4AF
+:101D40008DDF8032C1F784E1AFDF81E4ADDF86E56E
+:101D5000ABDF82E5A9DF80E2A7DF89E4A5DF83E5C9
+:101D6000A3DF80E5C7C0803429F478DF8638B0F07F
+:101D700075DF14C0813471F471DF803811F482E0B2
+:101D80001DC1813811F481E019C1823809F015C1F3
+:101D900082E114C1823421F484E19FDF89DFCBCF5B
+:101DA000853411F485E0F9CF8035C1F38135B1F385
+:101DB0008235A1F3853539F451DF809364004EDF1D
+:101DC00080936500EBCF863519F484E086DFF5C09B
+:101DD000843609F093C042DF809367013FDF809330
+:101DE0006601809169018E7F8093690137DF8534B8
+:101DF00029F480916901816080936901C0E0D0E09D
+:101E000006E610E005C02ADFF80181938F012196D4
+:101E10008091660190916701C817D907A0F31EDF72
+:101E2000803209F088CF8091690180FF1FC020E0D7
+:101E300030E0E6E6F0E012C0A0916400B0916500E9
+:101E40008191082EC5D08091640090916500019623
+:101E500090936500809364002F5F3F4F80916601EF
+:101E6000909167012817390738F343C0F894E19936
+:101E7000FECF1127E0916400F0916500EE0FFF1F87
+:101E8000C6E6D0E0809166019091670180FF01C0B5
+:101E90000196103051F422D003E000935700E895EA
+:101EA0001DD001E100935700E8950990199016D0D4
+:101EB00001E000935700E8951395103258F0112770
+:101EC0000DD005E000935700E89508D001E100939C
+:101ED0005700E8953296029739F0DBCF0091570012
+:101EE00001700130D9F30895103011F00296E7CF58
+:101EF000112484E1D9DE80E1D7DE1DCF843709F0DB
+:101F00004BC0ACDE80936701A9DE80936601A6DE3C
+:101F100090916901853421F49160909369010DC01D
+:101F20009E7F909369018091640090916500880F75
+:101F3000991F909365008093640090DE803209F0D1
+:101F4000FACE84E1B1DEC0E0D0E01EC0809169012C
+:101F500080FF07C0A0916400B091650031D0802D52
+:101F600008C081FD07C0E0916400F0916500E49134
+:101F70008E2F9ADE80916400909165000196909377
+:101F800065008093640021968091660190916701BD
+:101F9000C817D907D8F2AFCF853761F45FDE80323A
+:101FA00009F0C9CE84E180DE8EE17EDE83E97CDE4D
+:101FB00087E0A0CF863709F0BECE80E081DEBBCEC1
+:101FC000E199FECFBFBBAEBBE09A11960DB208956A
+:101FD000E199FECFBFBBAEBB0DBA11960FB6F89418
+:081FE000E29AE19A0FBE089598
+:021FE800800077
+:0400000300001C00DD
+:00000001FF
diff --git a/bootloaders/atmega8/Makefile b/bootloaders/atmega8/Makefile
new file mode 100644
index 0000000..8c0edd3
--- /dev/null
+++ b/bootloaders/atmega8/Makefile
@@ -0,0 +1,88 @@
+# Makefile for ATmegaBOOT
+# E.Lins, 2004-10-14
+
+# program name should not be changed...
+PROGRAM    = ATmegaBOOT
+
+PRODUCT=atmega8
+
+# enter the parameters for the UISP isp tool
+ISPPARAMS  = -dprog=stk500 -dserial=$(SERIAL) -dspeed=115200
+
+
+#DIRAVR = /usr/local/avr
+DIRAVRBIN = $(DIRAVR)/bin
+DIRAVRUTILS = $(DIRAVR)/utils/bin
+DIRINC = $(DIRAVR)/include
+DIRLIB = $(DIRAVR)/avr/lib
+
+
+MCU_TARGET = atmega8
+LDSECTION  = --section-start=.text=0x1c00
+FUSE_L     = 0xdf
+FUSE_H     = 0xca
+ISPFUSES   = $(DIRAVRBIN)/uisp -dpart=ATmega8 $(ISPPARAMS) --wr_fuse_l=$(FUSE_L) --wr_fuse_h=$(FUSE_H)
+ISPFLASH   = $(DIRAVRBIN)/uisp -dpart=ATmega8 $(ISPPARAMS) --erase --upload if=$(PROGRAM).hex -v
+
+
+OBJ        = $(PROGRAM).o
+OPTIMIZE   = -Os
+
+DEFS       = -DF_CPU=16000000 -DBAUD_RATE=19200
+LIBS       =
+
+CC         = $(DIRAVRBIN)/avr-gcc
+
+
+# Override is only needed by avr-lib build system.
+
+override CFLAGS        = -g -Wall $(OPTIMIZE) -mmcu=$(MCU_TARGET) -D$(PRODUCT) $(DEFS) -I$(DIRINC)
+override LDFLAGS       = -Wl,-Map,$(PROGRAM).map,$(LDSECTION)
+
+OBJCOPY        = $(DIRAVRBIN)/avr-objcopy
+OBJDUMP        = $(DIRAVRBIN)/avr-objdump
+SIZE           = $(DIRAVRBIN)/avr-size
+
+all: $(PROGRAM).elf lst text asm size
+
+isp: $(PROGRAM).hex
+	$(ISPFUSES)
+	$(ISPFLASH)
+
+$(PROGRAM).elf: $(OBJ)
+	$(CC) $(CFLAGS) $(LDFLAGS) -o $@ $^ $(LIBS)
+
+clean:
+	rm -rf *.s
+	rm -rf *.o *.elf
+	rm -rf *.lst *.map
+
+asm: $(PROGRAM).s
+
+%.s: %.c
+	$(CC) -S $(CFLAGS) -g1 $^
+
+lst:  $(PROGRAM).lst
+
+%.lst: %.elf
+	$(OBJDUMP) -h -S $< > $@
+
+size: $(PROGRAM).hex
+	$(SIZE) $^
+
+# Rules for building the .text rom images
+
+text: hex bin srec
+
+hex:  $(PROGRAM).hex
+bin:  $(PROGRAM).bin
+srec: $(PROGRAM).srec
+
+%.hex: %.elf
+	$(OBJCOPY) -j .text -j .data -O ihex $< $@
+
+%.srec: %.elf
+	$(OBJCOPY) -j .text -j .data -O srec $< $@
+
+%.bin: %.elf
+	$(OBJCOPY) -j .text -j .data -O binary $< $@
diff --git a/bootloaders/bt/ATmegaBOOT_168.c b/bootloaders/bt/ATmegaBOOT_168.c
new file mode 100644
index 0000000..a85dc9a
--- /dev/null
+++ b/bootloaders/bt/ATmegaBOOT_168.c
@@ -0,0 +1,1032 @@
+/**********************************************************/
+/* Serial Bootloader for Atmel megaAVR Controllers        */
+/*                                                        */
+/* tested with ATmega8, ATmega128 and ATmega168           */
+/* should work with other mega's, see code for details    */
+/*                                                        */
+/* ATmegaBOOT.c                                           */
+/*                                                        */
+/* build: 050815                                          */
+/* date : 15.08.2005                                      */
+/*                                                        */
+/* 20060802: hacked for Arduino by D. Cuartielles         */
+/*           based on a previous hack by D. Mellis        */
+/*           and D. Cuartielles                           */
+/*                                                        */
+/* Monitor and debug functions were added to the original */
+/* code by Dr. Erik Lins, chip45.com. (See below)         */
+/*                                                        */
+/* Thanks to Karl Pitrich for fixing a bootloader pin     */
+/* problem and more informative LED blinking!             */
+/*                                                        */
+/* For the latest version see:                            */
+/* http://www.chip45.com/                                 */
+/*                                                        */
+/* ------------------------------------------------------ */
+/*                                                        */
+/* based on stk500boot.c                                  */
+/* Copyright (c) 2003, Jason P. Kyle                      */
+/* All rights reserved.                                   */
+/* see avr1.org for original file and information         */
+/*                                                        */
+/* This program is free software; you can redistribute it */
+/* and/or modify it under the terms of the GNU General    */
+/* Public License as published by the Free Software       */
+/* Foundation; either version 2 of the License, or        */
+/* (at your option) any later version.                    */
+/*                                                        */
+/* This program is distributed in the hope that it will   */
+/* be useful, but WITHOUT ANY WARRANTY; without even the  */
+/* implied warranty of MERCHANTABILITY or FITNESS FOR A   */
+/* PARTICULAR PURPOSE.  See the GNU General Public        */
+/* License for more details.                              */
+/*                                                        */
+/* You should have received a copy of the GNU General     */
+/* Public License along with this program; if not, write  */
+/* to the Free Software Foundation, Inc.,                 */
+/* 59 Temple Place, Suite 330, Boston, MA  02111-1307 USA */
+/*                                                        */
+/* Licence can be viewed at                               */
+/* http://www.fsf.org/licenses/gpl.txt                    */
+/*                                                        */
+/* Target = Atmel AVR m128,m64,m32,m16,m8,m162,m163,m169, */
+/* m8515,m8535. ATmega161 has a very small boot block so  */
+/* isn't supported.                                       */
+/*                                                        */
+/* Tested with m128,m8,m163 - feel free to let me know    */
+/* how/if it works for you.                               */
+/*                                                        */
+/**********************************************************/
+
+
+/* some includes */
+#include <inttypes.h>
+#include <avr/io.h>
+#include <avr/pgmspace.h>
+#include <avr/interrupt.h>
+#include <avr/wdt.h>               
+
+
+#define set_output(sfr, bit) (_SFR_BYTE(sfr) |= _BV(bit))
+#define set_input(sfr, bit) (_SFR_BYTE(sfr) &= ~_BV(bit))
+
+
+#define high(sfr, bit) (_SFR_BYTE(sfr) |= _BV(bit))
+#define low(sfr, bit) (_SFR_BYTE(sfr) &= ~_BV(bit))
+
+
+
+
+/* the current avr-libc eeprom functions do not support the ATmega168 */
+/* own eeprom write/read functions are used instead */
+#ifndef __AVR_ATmega168__
+#include <avr/eeprom.h>
+#endif
+
+/* define F_CPU according to AVR_FREQ set in Makefile */
+/* Is there a better way to pass such a parameter from Makefile to source code ? */
+
+#define F_CPU     16000000L
+
+#include <util/delay.h> 
+
+
+/* 20060803: hacked by DojoCorp */
+/* set the waiting time for the bootloader */
+#define MAX_TIME_COUNT (F_CPU>>1)
+
+/* set the UART baud rate */
+/* 20060803: hacked by DojoCorp */
+#define BAUD_RATE   115200
+
+
+/* SW_MAJOR and MINOR needs to be updated from time to time to avoid warning message from AVR Studio */
+/* never allow AVR Studio to do an update !!!! */
+#define HW_VER	 0x02
+#define SW_MAJOR 0x01
+#define SW_MINOR 0x0f
+
+
+/* Adjust to suit whatever pin your hardware uses to enter the bootloader */
+/* ATmega128 has two UARTS so two pins are used to enter bootloader and select UART */
+/* BL0... means UART0, BL1... means UART1 */
+#ifdef __AVR_ATmega128__
+#define BL_DDR  DDRF
+#define BL_PORT PORTF
+#define BL_PIN  PINF
+#define BL0     PINF7
+#define BL1     PINF6
+#else
+/* other ATmegas have only one UART, so only one pin is defined to enter bootloader */
+#define BL_DDR  DDRD
+#define BL_PORT PORTD
+#define BL_PIN  PIND
+#define BL      PIND6
+#endif
+
+
+/* onboard LED is used to indicate, that the bootloader was entered (3x flashing) */
+/* if monitor functions are included, LED goes on after monitor was entered */
+#ifdef __AVR_ATmega128__
+/* Onboard LED is connected to pin PB7 (e.g. Crumb128, PROBOmega128, Savvy128) */
+#define LED_DDR  DDRB
+#define LED_PORT PORTB
+#define LED_PIN  PINB
+#define LED      PINB7
+#else
+/* Onboard LED is connected to pin PB2 (e.g. Crumb8, Crumb168) */
+#define LED_DDR  DDRB
+#define LED_PORT PORTB
+#define LED_PIN  PINB
+/* 20060803: hacked by DojoCorp, LED pin is B5 in Arduino */
+/* #define LED      PINB2 */
+#define LED      PINB5
+#endif
+
+
+/* monitor functions will only be compiled when using ATmega128, due to bootblock size constraints */
+#ifdef __AVR_ATmega128__
+#define MONITOR
+#endif
+
+
+/* define various device id's */
+/* manufacturer byte is always the same */
+#define SIG1	0x1E	// Yep, Atmel is the only manufacturer of AVR micros.  Single source :(
+
+#if defined __AVR_ATmega128__
+#define SIG2	0x97
+#define SIG3	0x02
+#define PAGE_SIZE	0x80U	//128 words
+
+#elif defined __AVR_ATmega64__
+#define SIG2	0x96
+#define SIG3	0x02
+#define PAGE_SIZE	0x80U	//128 words
+
+#elif defined __AVR_ATmega32__
+#define SIG2	0x95
+#define SIG3	0x02
+#define PAGE_SIZE	0x40U	//64 words
+
+#elif defined __AVR_ATmega16__
+#define SIG2	0x94
+#define SIG3	0x03
+#define PAGE_SIZE	0x40U	//64 words
+
+#elif defined __AVR_ATmega8__
+#define SIG2	0x93
+#define SIG3	0x07
+#define PAGE_SIZE	0x20U	//32 words
+
+#elif defined __AVR_ATmega88__
+#define SIG2	0x93
+#define SIG3	0x0a
+#define PAGE_SIZE	0x20U	//32 words
+
+#elif defined __AVR_ATmega168__
+#define SIG2	0x94
+#define SIG3	0x06
+#define PAGE_SIZE	0x40U	//64 words
+
+#elif defined __AVR_ATmega162__
+#define SIG2	0x94
+#define SIG3	0x04
+#define PAGE_SIZE	0x40U	//64 words
+
+#elif defined __AVR_ATmega163__
+#define SIG2	0x94
+#define SIG3	0x02
+#define PAGE_SIZE	0x40U	//64 words
+
+#elif defined __AVR_ATmega169__
+#define SIG2	0x94
+#define SIG3	0x05
+#define PAGE_SIZE	0x40U	//64 words
+
+#elif defined __AVR_ATmega8515__
+#define SIG2	0x93
+#define SIG3	0x06
+#define PAGE_SIZE	0x20U	//32 words
+
+#elif defined __AVR_ATmega8535__
+#define SIG2	0x93
+#define SIG3	0x08
+#define PAGE_SIZE	0x20U	//32 words
+#endif
+
+
+/* function prototypes */
+void putch(char);
+char getch(void);
+void getNch(uint8_t);
+void byte_response(uint8_t);
+void nothing_response(void);
+char gethex(void);
+void puthex(char);
+void flash_led(uint8_t);
+
+/* some variables */
+union address_union {
+    uint16_t word;
+    uint8_t  byte[2];
+} address;
+
+union length_union {
+    uint16_t word;
+    uint8_t  byte[2];
+} length;
+
+struct flags_struct {
+    unsigned eeprom : 1;
+    unsigned rampz  : 1;
+} flags;
+
+uint8_t buff[256];
+uint8_t address_high;
+
+uint8_t pagesz=0x80;
+
+uint8_t i;
+uint8_t bootuart = 0;
+
+void (*app_start)(void) = 0x0000;
+
+
+/* main program starts here */
+int main(void)
+{
+    uint8_t ch,ch2;
+    uint16_t w;
+
+    asm volatile("nop\n\t");
+
+    /* set pin direction for bootloader pin and enable pullup */
+    /* for ATmega128, two pins need to be initialized */
+#ifdef __AVR_ATmega128__
+    BL_DDR &= ~_BV(BL0);
+    BL_DDR &= ~_BV(BL1);
+    BL_PORT |= _BV(BL0);
+    BL_PORT |= _BV(BL1);
+#else
+    BL_DDR &= ~_BV(BL);
+    BL_PORT |= _BV(BL);
+#endif
+
+
+#ifdef __AVR_ATmega128__
+    /* check which UART should be used for booting */
+    if(bit_is_clear(BL_PIN, BL0)) {
+      bootuart = 1;
+    }
+    else if(bit_is_clear(BL_PIN, BL1)) {
+      bootuart = 2;
+    }
+#endif
+
+    /* check if flash is programmed already, if not start bootloader anyway */
+    if(pgm_read_byte_near(0x0000) != 0xFF) {
+
+#ifdef __AVR_ATmega128__
+	/* no UART was selected, start application */
+	if(!bootuart) {
+          app_start();
+	}
+#else
+	/* check if bootloader pin is set low */
+	/* we don't start this part neither for the m8, nor m168 */
+	//if(bit_is_set(BL_PIN, BL)) {
+    //      app_start();
+    //    }
+#endif
+    }
+
+#ifdef __AVR_ATmega128__    
+    /* no bootuart was selected, default to uart 0 */
+    if(!bootuart) {
+      bootuart = 1;
+    }
+#endif
+
+
+    /* initialize UART(s) depending on CPU defined */
+#ifdef __AVR_ATmega128__
+    if(bootuart == 1) {
+	UBRR0L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
+	UBRR0H = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
+	UCSR0A = 0x00;
+	UCSR0C = 0x06;
+	UCSR0B = _BV(TXEN0)|_BV(RXEN0);
+    }
+    if(bootuart == 2) {
+	UBRR1L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
+	UBRR1H = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
+	UCSR1A = 0x00;
+	UCSR1C = 0x06;
+	UCSR1B = _BV(TXEN1)|_BV(RXEN1);
+    }
+#elif defined __AVR_ATmega163__
+    UBRR = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
+    UBRRHI = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
+    UCSRA = 0x00;
+    UCSRB = _BV(TXEN)|_BV(RXEN);	
+#elif defined __AVR_ATmega168__  
+	UBRR0H = ((F_CPU / 16 + BAUD_RATE / 2) / BAUD_RATE - 1) >> 8;
+	UBRR0L = ((F_CPU / 16 + BAUD_RATE / 2) / BAUD_RATE - 1);
+
+
+    //UBRR0L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
+    //UBRR0H = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
+    UCSR0B = (1<<RXEN0) | (1<<TXEN0);
+    UCSR0C = (1<<UCSZ00) | (1<<UCSZ01);
+#elif defined __AVR_ATmega8__
+  /* m8 */
+  UBRRH = (((F_CPU/BAUD_RATE)/16)-1)>>8; 	// set baud rate
+  UBRRL = (((F_CPU/BAUD_RATE)/16)-1);
+  UCSRB = (1<<RXEN)|(1<<TXEN);  // enable Rx & Tx
+  UCSRC = (1<<URSEL)|(1<<UCSZ1)|(1<<UCSZ0);  // config USART; 8N1
+#else
+    /* m16,m32,m169,m8515,m8535 */
+    UBRRL = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
+    UBRRH = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
+    UCSRA = 0x00;
+    UCSRC = 0x06;
+    UCSRB = _BV(TXEN)|_BV(RXEN);
+#endif
+
+    /* set LED pin as output */
+    LED_DDR |= _BV(LED);
+              
+
+     
+      set_output(DDRD,PIND7);
+	  high(PORTD,PD7);    
+	  for (i = 0; i < 16; i++) {
+		 
+			_delay_loop_2(0);
+	  }
+	
+	
+	  low(PORTD,PD7);
+
+
+    /* flash onboard LED to signal entering of bootloader */
+#ifdef __AVR_ATmega128__
+    // 4x for UART0, 5x for UART1
+    flash_led(3 + bootuart);
+#else
+    flash_led(3);
+#endif
+    
+    /* 20050803: by DojoCorp, this is one of the parts provoking the
+                 system to stop listening, cancelled from the original */
+    //putch('\0');
+        
+
+   //message("SET BT PAGEMODE 3 2000 1");    
+putch('S');
+putch('E');
+putch('T');
+putch(' ');
+putch('B');
+putch('T');
+putch(' ');
+putch('P');
+putch('A');
+putch('G');
+putch('E');
+putch('M');
+putch('O');
+putch('D');
+putch('E');
+putch(' ');
+putch('3');
+putch(' ');
+putch('2');
+putch('0');
+putch('0');
+putch('0');
+putch(' ');
+putch('1');
+putch(0x0D);
+
+  
+	  //put_s("SET BT ROLE 0 f 7d00");  
+	putch('S');
+	putch('E');
+	putch('T');
+	putch(' ');
+	putch('B');
+	putch('T');
+	putch(' ');
+	putch('R');
+	putch('O');
+	putch('L');
+	putch('E');
+	putch(' ');
+	putch('0');
+	putch(' ');
+	putch('f');
+	putch(' ');
+	putch('7');
+	putch('d');
+	putch('0');
+	putch('0');
+	putch(0x0D);
+
+
+
+
+
+
+    /* forever loop */
+    for (;;) {
+
+	/* get character from UART */
+	ch = getch();
+
+	/* A bunch of if...else if... gives smaller code than switch...case ! */
+
+	/* Hello is anyone home ? */ 
+	if(ch=='0') {
+	    nothing_response();
+	}
+
+
+	/* Request programmer ID */
+	/* Not using PROGMEM string due to boot block in m128 being beyond 64kB boundry  */
+	/* Would need to selectively manipulate RAMPZ, and it's only 9 characters anyway so who cares.  */
+	else if(ch=='1') {
+	    if (getch() == ' ') {
+		putch(0x14);
+		putch('A');
+		putch('V');
+		putch('R');
+		putch(' ');
+		putch('I');
+		putch('S');
+		putch('P');
+		putch(0x10);
+	    }
+	}
+
+
+	/* AVR ISP/STK500 board commands  DON'T CARE so default nothing_response */
+	else if(ch=='@') {
+	    ch2 = getch();
+	    if (ch2>0x85) getch();
+	    nothing_response();
+	}
+
+
+	/* AVR ISP/STK500 board requests */
+	else if(ch=='A') {
+	    ch2 = getch();
+	    if(ch2==0x80) byte_response(HW_VER);		// Hardware version
+	    else if(ch2==0x81) byte_response(SW_MAJOR);	// Software major version
+	    else if(ch2==0x82) byte_response(SW_MINOR);	// Software minor version
+	    else if(ch2==0x98) byte_response(0x03);		// Unknown but seems to be required by avr studio 3.56
+	    else byte_response(0x00);				// Covers various unnecessary responses we don't care about
+	}
+
+
+	/* Device Parameters  DON'T CARE, DEVICE IS FIXED  */
+	else if(ch=='B') {
+	    getNch(20);
+	    nothing_response();
+	}
+
+
+	/* Parallel programming stuff  DON'T CARE  */
+	else if(ch=='E') {
+	    getNch(5);
+	    nothing_response();
+	}
+
+
+	/* Enter programming mode  */
+	else if(ch=='P') {
+	    nothing_response();
+	}
+
+
+	/* Leave programming mode  */
+	else if(ch=='Q') {
+	    nothing_response();
+	}
+
+
+	/* Erase device, don't care as we will erase one page at a time anyway.  */
+	else if(ch=='R') {
+	    nothing_response();
+	}
+
+
+	/* Set address, little endian. EEPROM in bytes, FLASH in words  */
+	/* Perhaps extra address bytes may be added in future to support > 128kB FLASH.  */
+	/* This might explain why little endian was used here, big endian used everywhere else.  */
+	else if(ch=='U') {
+	    address.byte[0] = getch();
+	    address.byte[1] = getch();
+	    nothing_response();
+	}
+
+
+	/* Universal SPI programming command, disabled.  Would be used for fuses and lock bits.  */
+	else if(ch=='V') {
+	    getNch(4);
+	    byte_response(0x00);
+	}
+
+
+	/* Write memory, length is big endian and is in bytes  */
+	else if(ch=='d') {
+	    length.byte[1] = getch();
+	    length.byte[0] = getch();
+	    flags.eeprom = 0;
+	    if (getch() == 'E') flags.eeprom = 1;
+	    for (w=0;w<length.word;w++) {
+		buff[w] = getch();	                        // Store data in buffer, can't keep up with serial data stream whilst programming pages
+	    }
+	    if (getch() == ' ') {
+		if (flags.eeprom) {		                //Write to EEPROM one byte at a time
+		    for(w=0;w<length.word;w++) {
+#ifdef __AVR_ATmega168__
+			while(EECR & (1<<EEPE));
+			EEAR = (uint16_t)(void *)address.word;
+			EEDR = buff[w];
+			EECR |= (1<<EEMPE);
+			EECR |= (1<<EEPE);
+#else
+			eeprom_write_byte((void *)address.word,buff[w]);
+#endif
+			address.word++;
+		    }			
+		}
+		else {					        //Write to FLASH one page at a time
+		    if (address.byte[1]>127) address_high = 0x01;	//Only possible with m128, m256 will need 3rd address byte. FIXME
+		    else address_high = 0x00;
+#ifdef __AVR_ATmega128__
+		    RAMPZ = address_high;
+#endif
+		    address.word = address.word << 1;	        //address * 2 -> byte location
+		    /* if ((length.byte[0] & 0x01) == 0x01) length.word++;	//Even up an odd number of bytes */
+		    if ((length.byte[0] & 0x01)) length.word++;	//Even up an odd number of bytes
+		    cli();					//Disable interrupts, just to be sure
+			// HACKME: EEPE used to be EEWE
+		    while(bit_is_set(EECR,EEPE));			//Wait for previous EEPROM writes to complete
+		    asm volatile(
+				 "clr	r17		\n\t"	//page_word_count
+				 "lds	r30,address	\n\t"	//Address of FLASH location (in bytes)
+				 "lds	r31,address+1	\n\t"
+				 "ldi	r28,lo8(buff)	\n\t"	//Start of buffer array in RAM
+				 "ldi	r29,hi8(buff)	\n\t"
+				 "lds	r24,length	\n\t"	//Length of data to be written (in bytes)
+				 "lds	r25,length+1	\n\t"
+				 "length_loop:		\n\t"	//Main loop, repeat for number of words in block							 							 
+				 "cpi	r17,0x00	\n\t"	//If page_word_count=0 then erase page
+				 "brne	no_page_erase	\n\t"						 
+				 "wait_spm1:		\n\t"
+				 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+				 "andi	r16,1           \n\t"
+				 "cpi	r16,1           \n\t"
+				 "breq	wait_spm1       \n\t"
+				 "ldi	r16,0x03	\n\t"	//Erase page pointed to by Z
+				 "sts	%0,r16		\n\t"
+				 "spm			\n\t"							 
+#ifdef __AVR_ATmega163__
+				 ".word 0xFFFF		\n\t"
+				 "nop			\n\t"
+#endif
+				 "wait_spm2:		\n\t"
+				 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+				 "andi	r16,1           \n\t"
+				 "cpi	r16,1           \n\t"
+				 "breq	wait_spm2       \n\t"									 
+
+				 "ldi	r16,0x11	\n\t"	//Re-enable RWW section
+				 "sts	%0,r16		\n\t"						 			 
+				 "spm			\n\t"
+#ifdef __AVR_ATmega163__
+				 ".word 0xFFFF		\n\t"
+				 "nop			\n\t"
+#endif
+				 "no_page_erase:		\n\t"							 
+				 "ld	r0,Y+		\n\t"	//Write 2 bytes into page buffer
+				 "ld	r1,Y+		\n\t"							 
+							 
+				 "wait_spm3:		\n\t"
+				 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+				 "andi	r16,1           \n\t"
+				 "cpi	r16,1           \n\t"
+				 "breq	wait_spm3       \n\t"
+				 "ldi	r16,0x01	\n\t"	//Load r0,r1 into FLASH page buffer
+				 "sts	%0,r16		\n\t"
+				 "spm			\n\t"
+							 
+				 "inc	r17		\n\t"	//page_word_count++
+				 "cpi r17,%1	        \n\t"
+				 "brlo	same_page	\n\t"	//Still same page in FLASH
+				 "write_page:		\n\t"
+				 "clr	r17		\n\t"	//New page, write current one first
+				 "wait_spm4:		\n\t"
+				 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+				 "andi	r16,1           \n\t"
+				 "cpi	r16,1           \n\t"
+				 "breq	wait_spm4       \n\t"
+#ifdef __AVR_ATmega163__
+				 "andi	r30,0x80	\n\t"	// m163 requires Z6:Z1 to be zero during page write
+#endif							 							 
+				 "ldi	r16,0x05	\n\t"	//Write page pointed to by Z
+				 "sts	%0,r16		\n\t"
+				 "spm			\n\t"
+#ifdef __AVR_ATmega163__
+				 ".word 0xFFFF		\n\t"
+				 "nop			\n\t"
+				 "ori	r30,0x7E	\n\t"	// recover Z6:Z1 state after page write (had to be zero during write)
+#endif
+				 "wait_spm5:		\n\t"
+				 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+				 "andi	r16,1           \n\t"
+				 "cpi	r16,1           \n\t"
+				 "breq	wait_spm5       \n\t"									 
+				 "ldi	r16,0x11	\n\t"	//Re-enable RWW section
+				 "sts	%0,r16		\n\t"						 			 
+				 "spm			\n\t"					 		 
+#ifdef __AVR_ATmega163__
+				 ".word 0xFFFF		\n\t"
+				 "nop			\n\t"
+#endif
+				 "same_page:		\n\t"							 
+				 "adiw	r30,2		\n\t"	//Next word in FLASH
+				 "sbiw	r24,2		\n\t"	//length-2
+				 "breq	final_write	\n\t"	//Finished
+				 "rjmp	length_loop	\n\t"
+				 "final_write:		\n\t"
+				 "cpi	r17,0		\n\t"
+				 "breq	block_done	\n\t"
+				 "adiw	r24,2		\n\t"	//length+2, fool above check on length after short page write
+				 "rjmp	write_page	\n\t"
+				 "block_done:		\n\t"
+				 "clr	__zero_reg__	\n\t"	//restore zero register
+#if defined __AVR_ATmega168__
+				 : "=m" (SPMCSR) : "M" (PAGE_SIZE) : "r0","r16","r17","r24","r25","r28","r29","r30","r31"
+#else
+				 : "=m" (SPMCR) : "M" (PAGE_SIZE) : "r0","r16","r17","r24","r25","r28","r29","r30","r31"
+#endif
+				 );
+		    /* Should really add a wait for RWW section to be enabled, don't actually need it since we never */
+		    /* exit the bootloader without a power cycle anyhow */
+		}
+		putch(0x14);
+		putch(0x10);
+	    }		
+	}
+    
+
+        /* Read memory block mode, length is big endian.  */
+        else if(ch=='t') {
+	    length.byte[1] = getch();
+	    length.byte[0] = getch();
+#if defined __AVR_ATmega128__
+	    if (address.word>0x7FFF) flags.rampz = 1;		// No go with m256, FIXME
+	    else flags.rampz = 0;
+#endif
+	    if (getch() == 'E') flags.eeprom = 1;
+	    else {
+		flags.eeprom = 0;
+		address.word = address.word << 1;	        // address * 2 -> byte location
+	    }
+	    if (getch() == ' ') {		                // Command terminator
+		putch(0x14);
+		for (w=0;w < length.word;w++) {		        // Can handle odd and even lengths okay
+		    if (flags.eeprom) {	                        // Byte access EEPROM read
+#ifdef __AVR_ATmega168__
+			while(EECR & (1<<EEPE));
+			EEAR = (uint16_t)(void *)address.word;
+			EECR |= (1<<EERE);
+			putch(EEDR);
+#else
+			putch(eeprom_read_byte((void *)address.word));
+#endif
+			address.word++;
+		    }
+		    else {
+
+			if (!flags.rampz) putch(pgm_read_byte_near(address.word));
+#if defined __AVR_ATmega128__
+			else putch(pgm_read_byte_far(address.word + 0x10000));
+			// Hmmmm, yuck  FIXME when m256 arrvies
+#endif
+			address.word++;
+		    }
+		}
+		putch(0x10);
+	    }
+	}
+
+
+        /* Get device signature bytes  */
+        else if(ch=='u') {
+	    if (getch() == ' ') {
+		putch(0x14);
+		putch(SIG1);
+		putch(SIG2);
+		putch(SIG3);
+		putch(0x10);
+	    }
+	}
+
+
+        /* Read oscillator calibration byte */
+        else if(ch=='v') {
+	    byte_response(0x00);
+	}
+
+
+#ifdef MONITOR
+
+	/* here come the extended monitor commands by Erik Lins */
+
+	/* check for three times exclamation mark pressed */
+	else if(ch=='!') {
+	    ch = getch();
+	    if(ch=='!') {
+		ch = getch();
+		if(ch=='!') {
+
+#ifdef __AVR_ATmega128__
+		    uint16_t extaddr;
+#endif
+		    uint8_t addrl, addrh;
+
+#ifdef CRUMB128
+		    PGM_P welcome = {"ATmegaBOOT / Crumb128 - (C) J.P.Kyle, E.Lins - 050815\n\r"};
+#elif defined PROBOMEGA128
+		    PGM_P welcome = {"ATmegaBOOT / PROBOmega128 - (C) J.P.Kyle, E.Lins - 050815\n\r"};
+#elif defined SAVVY128
+		    PGM_P welcome = {"ATmegaBOOT / Savvy128 - (C) J.P.Kyle, E.Lins - 050815\n\r"};
+#endif
+
+		    /* turn on LED */
+		    LED_DDR |= _BV(LED);
+		    LED_PORT &= ~_BV(LED);
+
+		    /* print a welcome message and command overview */
+		    for(i=0; welcome[i] != '\0'; ++i) {
+			putch(welcome[i]);
+		    }
+
+		    /* test for valid commands */
+		    for(;;) {
+			putch('\n');
+			putch('\r');
+			putch(':');
+			putch(' ');
+
+			ch = getch();
+			putch(ch);
+
+			/* toggle LED */
+			if(ch == 't') {
+			    if(bit_is_set(LED_PIN,LED)) {
+				LED_PORT &= ~_BV(LED);
+				putch('1');
+			    } else {
+				LED_PORT |= _BV(LED);
+				putch('0');
+			    }
+
+			} 
+
+			/* read byte from address */
+			else if(ch == 'r') {
+			    ch = getch(); putch(ch);
+			    addrh = gethex();
+			    addrl = gethex();
+			    putch('=');
+			    ch = *(uint8_t *)((addrh << 8) + addrl);
+			    puthex(ch);
+			}
+
+			/* write a byte to address  */
+			else if(ch == 'w') {
+			    ch = getch(); putch(ch);
+			    addrh = gethex();
+			    addrl = gethex();
+			    ch = getch(); putch(ch);
+			    ch = gethex();
+			    *(uint8_t *)((addrh << 8) + addrl) = ch;
+
+			}
+
+			/* read from uart and echo back */
+			else if(ch == 'u') {
+			    for(;;) {
+				putch(getch());
+			    }
+			}
+#ifdef __AVR_ATmega128__
+			/* external bus loop  */
+			else if(ch == 'b') {
+			    putch('b');
+			    putch('u');
+			    putch('s');
+			    MCUCR = 0x80;
+			    XMCRA = 0;
+			    XMCRB = 0;
+			    extaddr = 0x1100;
+			    for(;;) {
+				ch = *(volatile uint8_t *)extaddr;
+				if(++extaddr == 0) {
+				    extaddr = 0x1100;
+				}
+			    }
+			}
+#endif
+
+			else if(ch == 'j') {
+			    app_start();
+			}
+
+		    }
+		    /* end of monitor functions */
+
+		}
+	    }
+	}
+	/* end of monitor */
+#endif
+
+
+    }
+    /* end of forever loop */
+
+}
+
+
+char gethex(void) {
+    char ah,al;
+
+    ah = getch(); putch(ah);
+    al = getch(); putch(al);
+    if(ah >= 'a') {
+	ah = ah - 'a' + 0x0a;
+    } else if(ah >= '0') {
+	ah -= '0';
+    }
+    if(al >= 'a') {
+	al = al - 'a' + 0x0a;
+    } else if(al >= '0') {
+	al -= '0';
+    }
+    return (ah << 4) + al;
+}
+
+
+void puthex(char ch) {
+    char ah,al;
+
+    ah = (ch & 0xf0) >> 4;
+    if(ah >= 0x0a) {
+	ah = ah - 0x0a + 'a';
+    } else {
+	ah += '0';
+    }
+    al = (ch & 0x0f);
+    if(al >= 0x0a) {
+	al = al - 0x0a + 'a';
+    } else {
+	al += '0';
+    }
+    putch(ah);
+    putch(al);
+}
+
+
+void putch(char ch)
+{
+#ifdef __AVR_ATmega128__
+    if(bootuart == 1) {
+	while (!(UCSR0A & _BV(UDRE0)));
+	UDR0 = ch;
+    }
+    else if (bootuart == 2) {
+	while (!(UCSR1A & _BV(UDRE1)));
+	UDR1 = ch;
+    }
+#elif defined __AVR_ATmega168__
+    while (!(UCSR0A & _BV(UDRE0)));
+    UDR0 = ch;
+#else
+    /* m8,16,32,169,8515,8535,163 */
+    while (!(UCSRA & _BV(UDRE)));
+    UDR = ch;
+#endif
+}
+
+
+char getch(void)
+{
+#ifdef __AVR_ATmega128__
+    if(bootuart == 1) {
+	while(!(UCSR0A & _BV(RXC0)));
+	return UDR0;
+    }
+    else if(bootuart == 2) {
+	while(!(UCSR1A & _BV(RXC1)));
+	return UDR1;
+    }
+    return 0;
+#elif defined __AVR_ATmega168__
+    uint32_t count = 0;
+    while(!(UCSR0A & _BV(RXC0))){
+    	/* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/               
+    	/* HACKME:: here is a good place to count times*/
+    	count++;
+    	if (count > MAX_TIME_COUNT)
+    		app_start();
+     }
+    return UDR0;
+#else
+    /* m8,16,32,169,8515,8535,163 */
+    uint32_t count = 0;
+    while(!(UCSRA & _BV(RXC))){
+    	/* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/               
+    	/* HACKME:: here is a good place to count times*/
+    	count++;
+    	if (count > MAX_TIME_COUNT)
+    		app_start();
+     }
+    return UDR;
+#endif
+}
+
+
+void getNch(uint8_t count)
+{
+    uint8_t i;
+    for(i=0;i<count;i++) {
+#ifdef __AVR_ATmega128__
+	if(bootuart == 1) {
+	    while(!(UCSR0A & _BV(RXC0)));
+	    UDR0;
+	} 
+	else if(bootuart == 2) {
+	    while(!(UCSR1A & _BV(RXC1)));
+	    UDR1;
+	}
+#elif defined __AVR_ATmega168__
+	while(!(UCSR0A & _BV(RXC0)));
+	UDR0;
+#else
+	/* m8,16,32,169,8515,8535,163 */
+   	/* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/               
+	//while(!(UCSRA & _BV(RXC)));
+	//UDR;
+    uint8_t i;
+    for(i=0;i<count;i++) {
+    	getch(); // need to handle time out
+    }
+#endif		
+    }
+}
+
+
+void byte_response(uint8_t val)
+{
+    if (getch() == ' ') {
+	putch(0x14);
+	putch(val);
+	putch(0x10);
+    }
+}
+
+
+void nothing_response(void)
+{
+    if (getch() == ' ') {
+	putch(0x14);
+	putch(0x10);
+    }
+}
+
+void flash_led(uint8_t count)
+{
+    /* flash onboard LED three times to signal entering of bootloader */
+    uint32_t l;
+
+    if (count == 0) {
+      count = 3;
+    }
+    
+    for (i = 0; i < count; ++i) {
+	LED_PORT |= _BV(LED);
+	for(l = 0; l < (2 * F_CPU); ++l);
+	LED_PORT &= ~_BV(LED);
+	for(l = 0; l < (F_CPU / 5); ++l);
+    }
+}
+
+
+/* end of file ATmegaBOOT.c */
diff --git a/bootloaders/bt/ATmegaBOOT_168.hex b/bootloaders/bt/ATmegaBOOT_168.hex
new file mode 100644
index 0000000..036ae54
--- /dev/null
+++ b/bootloaders/bt/ATmegaBOOT_168.hex
@@ -0,0 +1,121 @@
+:103800000C94341C0C944F1C0C944F1C0C944F1CA7
+:103810000C944F1C0C944F1C0C944F1C0C944F1C7C
+:103820000C944F1C0C944F1C0C944F1C0C944F1C6C
+:103830000C944F1C0C944F1C0C944F1C0C944F1C5C
+:103840000C944F1C0C944F1C0C944F1C0C944F1C4C
+:103850000C944F1C0C944F1C0C944F1C0C944F1C3C
+:103860000C944F1C0C944F1C11241FBECFEFD4E0BE
+:10387000DEBFCDBF11E0A0E0B1E0E0E6FFE302C0B3
+:1038800005900D92A230B107D9F712E0A2E0B1E0A5
+:1038900001C01D92AC30B107E1F70C94D61C0C941A
+:1038A000001C882309F483E01092090290E0981725
+:1038B000F0F4692F2D9A2FEF37E448EE51E02253B0
+:1038C00030404040504057FFFACF2D982FEF33ED56
+:1038D00040E350E0225330404040504057FFFACF81
+:1038E000962F9F5F692F981728F3909309020895E8
+:1038F000982F8091C00085FFFCCF9093C60008955B
+:10390000EF92FF920F931F93EE24FF248701809183
+:10391000C00087FD17C00894E11CF11C011D111D9A
+:1039200081E0E81682E1F8068AE7080780E01807D8
+:1039300070F3E0910201F091030109958091C000BC
+:1039400087FFE9CF8091C600992787FD90951F9149
+:103950000F91FF90EF9008950E94801C803209F033
+:10396000089584E10E94781C80E10E94781C0895EB
+:10397000CF93C82F0E94801C803249F484E10E94BA
+:10398000781C8C2F0E94781C80E10E94781CCF91BB
+:103990000895282F90E007C08091C0008823E4F7A5
+:1039A0008091C6009F5F9217B8F30895CFEFD4E0DF
+:1039B000DEBFCDBF000056985E9A1092C50088E029
+:1039C0008093C40088E18093C10086E08093C200A8
+:1039D000259A579A5F9A109209022FE080E090E0B2
+:1039E0000197F1F7215027FFF9CF20E12093090239
+:1039F0005F9883E00E94511C83E50E94781C85E457
+:103A00000E94781C84E50E94781C80E20E94781C49
+:103A100082E40E94781C84E50E94781C80E20E9467
+:103A2000781C80E50E94781C81E40E94781C87E461
+:103A30000E94781C85E40E94781C8DE40E94781C0A
+:103A40008FE40E94781C84E40E94781C85E40E9424
+:103A5000781C80E20E94781C83E30E94781C80E23C
+:103A60000E94781C82E30E94781C80E30E94781CEC
+:103A700080E30E94781C80E30E94781C80E20E9410
+:103A8000781C81E30E94781C8DE00E94781C83E5FD
+:103A90000E94781C85E40E94781C84E50E94781CB2
+:103AA00080E20E94781C82E40E94781C84E50E94D7
+:103AB000781C80E20E94781C82E50E94781C8FE4CA
+:103AC0000E94781C8CE40E94781C85E40E94781C7B
+:103AD00080E20E94781C80E30E94781C80E20E94B1
+:103AE000781C86E60E94781C80E20E94781C87E39E
+:103AF0000E94781C84E60E94781C80E30E94781C57
+:103B000080E30E94781C8DE00E94781C0E94801C3B
+:103B1000803361F1813369F1803409F449C0813423
+:103B200009F44FC0823409F45DC0853409F460C0E3
+:103B30008035E1F08135D1F08235C1F0853509F469
+:103B40005BC0863509F463C0843609F465C08437E8
+:103B500009F4B9C0853709F414C18637B9F680E095
+:103B60000E94B81C0E94801C8033A1F60E94AC1CED
+:103B7000CDCF0E94801CC82F803241F684E10E9484
+:103B8000781C81E40E94781C86E50E94781C82E5FE
+:103B90000E94781C8C2F0E94781C89E40E94781C5B
+:103BA00083E50E94781C80E50E94781C80E1ACCF00
+:103BB0000E94801C8638D0F20E94801C0E94AC1C9F
+:103BC000A5CF0E94801C803809F4EDC0813809F42B
+:103BD000EEC0823809F4EFC0883909F683E00E940C
+:103BE000B81CC0CF84E10E94C91C0E94AC1C8ECFBF
+:103BF00085E00E94C91CF9CF0E94801C80930501BA
+:103C00000E94801C809306010E94AC1C7FCF84E040
+:103C10000E94C91C80E0A4CF0E94801C80930802EF
+:103C20000E94801C8093070280910B028E7F8093FC
+:103C30000B020E94801C853409F4C1C000E010E032
+:103C400080910702909108021816190670F4C7E0D7
+:103C5000D1E00E94801C89930F5F1F4F8091070263
+:103C60009091080208171907A0F30E94801C803267
+:103C700009F04CCF80910B0280FFADC000E010E056
+:103C8000209107023091080212161306C0F4E09149
+:103C90000501F0910601A7E0B1E0F999FECFF2BD70
+:103CA000E1BD8D9180BDFA9AF99A31960F5F1F4F51
+:103CB0000217130790F3F0930601E093050184E1E6
+:103CC0000E94781C73CF0E94801C809308020E947F
+:103CD000801C809307020E94801C853409F475C003
+:103CE00080910B028E7F80930B0280910501909151
+:103CF0000601880F991F90930601809305010E9489
+:103D0000801C803209F002CF84E10E94781C00E020
+:103D100010E020910702309108021216130608F0F5
+:103D200045CFE0910501F091060180910B0280FFE3
+:103D30001FC0F999FECFF2BDE1BDF89A80B50E948F
+:103D4000781CE0910501F09106013196F09306018F
+:103D5000E093050120910702309108020F5F1F4F89
+:103D60000217130708F022CF80910B0280FDE1CFEC
+:103D7000869580FF9BC03196F0930601E093050184
+:103D8000EDCF0E94801C803209F0C0CE84E10E94F9
+:103D9000781C8EE10E94781C84E90E94781C86E0E1
+:103DA0000E94781C03CF82E00E94B81CDBCE81E029
+:103DB0000E94B81CD7CE8FE00E94B81CD3CE809151
+:103DC0000B02816080930B0239CF80910B028160DE
+:103DD00080930B0294CF8091060187FD73C01092EF
+:103DE0000A028091050190910601880F991F909316
+:103DF0000601809305018091070280FF09C0809130
+:103E0000070290910802019690930802809307029E
+:103E1000F894F999FECF1127E0910501F091060180
+:103E2000C7E0D1E08091070290910802103091F430
+:103E30000091570001700130D9F303E0009357005F
+:103E4000E8950091570001700130D9F301E100932A
+:103E50005700E895099019900091570001700130C2
+:103E6000D9F301E000935700E8951395103498F0CA
+:103E700011270091570001700130D9F305E000933C
+:103E80005700E8950091570001700130D9F301E126
+:103E900000935700E8953296029709F0C7CF10308B
+:103EA00011F00296E5CF112484E10ACF84910E949B
+:103EB000781C2091070230910802E0910501F091F1
+:103EC000060159CF81E080930A028BCF1F93CF93D5
+:103ED0000E94801CC82F0E94781C0E94801C182FF2
+:103EE0000E94781CC1362CF0C75511363CF017558E
+:103EF00008C0C033D4F3C0531136CCF710330CF0E4
+:103F00001053C295C07FC10F8C2F992787FD9095C4
+:103F1000CF911F910895CF93282F992787FD9095D2
+:103F2000807F9070959587959595879595958795C0
+:103F3000959587958A303CF0895AC22FCF70CA3048
+:103F40003CF0C95A06C0805DC22FCF70CA30CCF792
+:103F5000C05D0E94781C8C2F0E94781CCF91089520
+:023F60008000DF
+:0400000300003800C1
+:00000001FF
diff --git a/bootloaders/lilypad/LilyPadBOOT_168.hex b/bootloaders/lilypad/LilyPadBOOT_168.hex
new file mode 100644
index 0000000..aea378e
--- /dev/null
+++ b/bootloaders/lilypad/LilyPadBOOT_168.hex
@@ -0,0 +1,117 @@
+:103800000C94341C0C944F1C0C944F1C0C944F1CA7
+:103810000C944F1C0C944F1C0C944F1C0C944F1C7C
+:103820000C944F1C0C944F1C0C944F1C0C944F1C6C
+:103830000C944F1C0C944F1C0C944F1C0C944F1C5C
+:103840000C944F1C0C944F1C0C944F1C0C944F1C4C
+:103850000C944F1C0C944F1C0C944F1C0C944F1C3C
+:103860000C944F1C0C944F1C11241FBECFEFD4E0BE
+:10387000DEBFCDBF11E0A0E0B1E0E8E1FFE302C0B0
+:1038800005900D92A230B107D9F712E0A2E0B1E0A5
+:1038900001C01D92AD30B107E1F70C94311D0C94BD
+:1038A000001CCF93DF93CDB7DEB724970FB6F89403
+:1038B000DEBF0FBECDBF382F882309F433E010924E
+:1038C0000A02332309F44BC020E02D9A19821A8290
+:1038D0001B821C8289819A81AB81BC8180549F416B
+:1038E000A040B040A0F489819A81AB81BC8101964F
+:1038F000A11DB11D89839A83AB83BC8389819A8181
+:10390000AB81BC8180549F41A040B04060F32D98B2
+:1039100019821A821B821C8289819A81AB81BC81A7
+:1039200080549F41A040B040A0F489819A81AB812E
+:10393000BC810196A11DB11D89839A83AB83BC8391
+:1039400089819A81AB81BC8180549F41A040B04065
+:1039500060F32F5F231708F4B8CF20930A02249650
+:103960000FB6F894DEBF0FBECDBFDF91CF910895A3
+:10397000EF92FF920F931F93EE24FF248701809113
+:10398000C00087FD17C00894E11CF11C011D111D2A
+:1039900081E0E81689E0F8068DE3080780E0180763
+:1039A00070F3E0910201F091030109958091C0004C
+:1039B00087FFE9CF8091C600992787FD90951F91D9
+:1039C0000F91FF90EF900895982F8091C00085FF90
+:1039D000FCCF9093C60008950E94B81C803271F00D
+:1039E000809104018F5F80930401853009F0089570
+:1039F000E0910201F09103010995089584E10E948C
+:103A0000E41C80E10E94E41C08951F93182F0E947B
+:103A1000B81C803269F0809104018F5F80930401AB
+:103A2000853079F4E0910201F0910301099509C014
+:103A300084E10E94E41C812F0E94E41C80E10E942A
+:103A4000E41C1F910895282F882351F090E0809165
+:103A5000C00087FFFCCF8091C6009F5F2917B9F790
+:103A60000895CFEFD4E0DEBFCDBF000089E18093A1
+:103A7000C4001092C50088E18093C10086E0809365
+:103A8000C2005098589A259A83E00E94511C0E94C7
+:103A9000B81C8033B1F18133B9F1803409F454C0DA
+:103AA000813409F45AC0823409F469C0853409F4B8
+:103AB0006CC0803531F1813521F1823511F18535C8
+:103AC00009F4B2C0863509F4BAC0843609F463C07B
+:103AD000843709F4BBC0853709F40EC1863709F471
+:103AE0004AC0809104018F5F80930401853079F68C
+:103AF000E0910201F091030109950E94B81C803306
+:103B000051F60E94EC1CC3CF0E94B81C803249F7CA
+:103B100084E10E94E41C81E40E94E41C86E50E948A
+:103B2000E41C82E50E94E41C80E20E94E41C89E41B
+:103B30000E94E41C83E50E94E41C80E50E94E41CD2
+:103B400080E10E94E41CA3CF0E94B81C8638C8F212
+:103B50000E94B81C0E94EC1C9ACF0E94B81C8038AE
+:103B600009F4F7C0813809F4F8C0823809F4F9C0C3
+:103B7000883909F4BDC080E00E94051D88CF84E12A
+:103B80000E94231D0E94EC1C82CF85E00E94231D11
+:103B90000E94EC1C7CCF0E94B81C809309020E94FA
+:103BA000B81C8093080280910C028E7F80930C02D7
+:103BB0000E94B81C853409F4C6C080910802909117
+:103BC0000902892B09F0ADC00E94B81C803209F0AF
+:103BD00088CF80910C0280FFC8C08091080290912C
+:103BE00009020097D1F02091060130910701E8E029
+:103BF000F1E0AC014E0F5F1FF999FECF32BD21BD40
+:103C0000819180BDFA9AF99A2F5F3F4F4E175F0757
+:103C100099F7309307012093060184E10E94E41C88
+:103C200080E10E94E41C33CF0E94B81C80930601FF
+:103C30000E94B81C809307010E94EC1C28CF84E0EE
+:103C40000E94231D80E00E94051D21CF0E94B81C08
+:103C5000809309020E94B81C809308020E94B81C3D
+:103C6000853409F4F4C080910C028E7F80930C029D
+:103C70008091060190910701880F991F9093070189
+:103C8000809306010E94B81C803209F000CF84E1C5
+:103C90000E94E41C2091080230910902211531058F
+:103CA00019F1C0E0D0E0E0910601F09107018091A8
+:103CB0000C0280FFC4C0F999FECFF2BDE1BDF89AB5
+:103CC00080B50E94E41CE0910601F0910701319655
+:103CD000F0930701E0930601209108023091090258
+:103CE0002196C217D30718F380E10E94E41CCFCEBF
+:103CF00083E00E94051DCBCE0E94B81C803209F0E3
+:103D0000F0CE84E10E94E41C8EE10E94E41C84E970
+:103D10000E94E41C86E00E94E41C80E10E94E41CF6
+:103D2000B6CEC0E0D0E008E011E00E94B81CF80177
+:103D300081938F0121968091080290910902C81702
+:103D4000D90798F341CF80910C02816080930C02D7
+:103D500034CF82E00E94051D9ACE81E00E94051DAD
+:103D600096CE80E10E94051D92CE8091070187FDCD
+:103D700080C010920B028091060190910701880F7C
+:103D8000991F90930701809306018091080280FF9C
+:103D900009C080910802909109020196909309024E
+:103DA00080930802F894F999FECF1127E09106015B
+:103DB000F0910701C8E0D1E08091080290910902DA
+:103DC000103091F40091570001700130D9F303E0F5
+:103DD00000935700E8950091570001700130D9F326
+:103DE00001E100935700E895099019900091570060
+:103DF00001700130D9F301E000935700E895139565
+:103E0000103498F011270091570001700130D9F358
+:103E100005E000935700E8950091570001700130CC
+:103E2000D9F301E100935700E8953296029709F023
+:103E3000C7CF103011F00296E5CF1124EECE81FFEE
+:103E40000CC03196F0930701E093060149CF8091B1
+:103E50000C02816080930C0215CF84910E94E41CB7
+:103E60002091080230910902E0910601F0910701CA
+:103E7000E8CF81E080930B027ECF0F931F930E94C7
+:103E8000B81C182F0E94E41C0E94B81C082F0E9426
+:103E9000E41C11362CF0175501363CF0075508C0CC
+:103EA0001033D4F310530136CCF700330CF0005329
+:103EB0001295107F100F812F992787FD90951F91E4
+:103EC0000F9108951F93282F992787FD9095807F44
+:103ED00090709595879595958795959587959595E6
+:103EE00087958A304CF0982F995A822F8F708A309C
+:103EF0004CF0182F195A08C0982F905D822F8F70A0
+:103F00008A30BCF7182F105D892F0E94E41C812F86
+:083F10000E94E41C1F910895BA
+:023F1800800027
+:0400000300003800C1
+:00000001FF
diff --git a/bootloaders/lilypad/src/ATmegaBOOT.c b/bootloaders/lilypad/src/ATmegaBOOT.c
new file mode 100644
index 0000000..915bc57
--- /dev/null
+++ b/bootloaders/lilypad/src/ATmegaBOOT.c
@@ -0,0 +1,979 @@
+/**********************************************************/
+/* Serial Bootloader for Atmel megaAVR Controllers        */
+/*                                                        */
+/* tested with ATmega8, ATmega128 and ATmega168           */
+/* should work with other mega's, see code for details    */
+/*                                                        */
+/* ATmegaBOOT.c                                           */
+/*                                                        */
+/* 20070626: hacked for Arduino Diecimila (which auto-    */
+/*           resets when a USB connection is made to it)  */
+/*           by D. Mellis                                 */
+/* 20060802: hacked for Arduino by D. Cuartielles         */
+/*           based on a previous hack by D. Mellis        */
+/*           and D. Cuartielles                           */
+/*                                                        */
+/* Monitor and debug functions were added to the original */
+/* code by Dr. Erik Lins, chip45.com. (See below)         */
+/*                                                        */
+/* Thanks to Karl Pitrich for fixing a bootloader pin     */
+/* problem and more informative LED blinking!             */
+/*                                                        */
+/* For the latest version see:                            */
+/* http://www.chip45.com/                                 */
+/*                                                        */
+/* ------------------------------------------------------ */
+/*                                                        */
+/* based on stk500boot.c                                  */
+/* Copyright (c) 2003, Jason P. Kyle                      */
+/* All rights reserved.                                   */
+/* see avr1.org for original file and information         */
+/*                                                        */
+/* This program is free software; you can redistribute it */
+/* and/or modify it under the terms of the GNU General    */
+/* Public License as published by the Free Software       */
+/* Foundation; either version 2 of the License, or        */
+/* (at your option) any later version.                    */
+/*                                                        */
+/* This program is distributed in the hope that it will   */
+/* be useful, but WITHOUT ANY WARRANTY; without even the  */
+/* implied warranty of MERCHANTABILITY or FITNESS FOR A   */
+/* PARTICULAR PURPOSE.  See the GNU General Public        */
+/* License for more details.                              */
+/*                                                        */
+/* You should have received a copy of the GNU General     */
+/* Public License along with this program; if not, write  */
+/* to the Free Software Foundation, Inc.,                 */
+/* 59 Temple Place, Suite 330, Boston, MA  02111-1307 USA */
+/*                                                        */
+/* Licence can be viewed at                               */
+/* http://www.fsf.org/licenses/gpl.txt                    */
+/*                                                        */
+/* Target = Atmel AVR m128,m64,m32,m16,m8,m162,m163,m169, */
+/* m8515,m8535. ATmega161 has a very small boot block so  */
+/* isn't supported.                                       */
+/*                                                        */
+/* Tested with m168                                       */
+/**********************************************************/
+
+/* $Id$ */
+
+
+/* some includes */
+#include <inttypes.h>
+#include <avr/io.h>
+#include <avr/pgmspace.h>
+#include <avr/interrupt.h>
+#include <avr/wdt.h>
+
+
+/* the current avr-libc eeprom functions do not support the ATmega168 */
+/* own eeprom write/read functions are used instead */
+#ifndef __AVR_ATmega168__
+#include <avr/eeprom.h>
+#endif
+
+/* Use the F_CPU defined in Makefile */
+
+/* 20060803: hacked by DojoCorp */
+/* 20070626: hacked by David A. Mellis to decrease waiting time for auto-reset */
+/* set the waiting time for the bootloader */
+/* get this from the Makefile instead */
+/* #define MAX_TIME_COUNT (F_CPU>>4) */
+
+/* 20070707: hacked by David A. Mellis - after this many errors give up and launch application */
+#define MAX_ERROR_COUNT 5
+
+/* set the UART baud rate */
+/* 20060803: hacked by DojoCorp */
+//#define BAUD_RATE   115200
+#define BAUD_RATE   19200
+
+
+/* SW_MAJOR and MINOR needs to be updated from time to time to avoid warning message from AVR Studio */
+/* never allow AVR Studio to do an update !!!! */
+#define HW_VER	 0x02
+#define SW_MAJOR 0x01
+#define SW_MINOR 0x10
+
+
+/* Adjust to suit whatever pin your hardware uses to enter the bootloader */
+/* ATmega128 has two UARTS so two pins are used to enter bootloader and select UART */
+/* BL0... means UART0, BL1... means UART1 */
+#ifdef __AVR_ATmega128__
+#define BL_DDR  DDRF
+#define BL_PORT PORTF
+#define BL_PIN  PINF
+#define BL0     PINF7
+#define BL1     PINF6
+#else
+/* other ATmegas have only one UART, so only one pin is defined to enter bootloader */
+#define BL_DDR  DDRD
+#define BL_PORT PORTD
+#define BL_PIN  PIND
+#define BL      PIND6
+#endif
+
+
+/* onboard LED is used to indicate, that the bootloader was entered (3x flashing) */
+/* if monitor functions are included, LED goes on after monitor was entered */
+#ifdef __AVR_ATmega128__
+/* Onboard LED is connected to pin PB7 (e.g. Crumb128, PROBOmega128, Savvy128) */
+#define LED_DDR  DDRB
+#define LED_PORT PORTB
+#define LED_PIN  PINB
+#define LED      PINB7
+#else
+/* Onboard LED is connected to pin PB2 (e.g. Crumb8, Crumb168) */
+#define LED_DDR  DDRB
+#define LED_PORT PORTB
+#define LED_PIN  PINB
+/* 20060803: hacked by DojoCorp, LED pin is B5 in Arduino */
+/* #define LED      PINB2 */
+#define LED      PINB5
+#endif
+
+
+/* monitor functions will only be compiled when using ATmega128, due to bootblock size constraints */
+#ifdef __AVR_ATmega128__
+#define MONITOR
+#endif
+
+
+/* define various device id's */
+/* manufacturer byte is always the same */
+#define SIG1	0x1E	// Yep, Atmel is the only manufacturer of AVR micros.  Single source :(
+
+#if defined __AVR_ATmega128__
+#define SIG2	0x97
+#define SIG3	0x02
+#define PAGE_SIZE	0x80U	//128 words
+
+#elif defined __AVR_ATmega64__
+#define SIG2	0x96
+#define SIG3	0x02
+#define PAGE_SIZE	0x80U	//128 words
+
+#elif defined __AVR_ATmega32__
+#define SIG2	0x95
+#define SIG3	0x02
+#define PAGE_SIZE	0x40U	//64 words
+
+#elif defined __AVR_ATmega16__
+#define SIG2	0x94
+#define SIG3	0x03
+#define PAGE_SIZE	0x40U	//64 words
+
+#elif defined __AVR_ATmega8__
+#define SIG2	0x93
+#define SIG3	0x07
+#define PAGE_SIZE	0x20U	//32 words
+
+#elif defined __AVR_ATmega88__
+#define SIG2	0x93
+#define SIG3	0x0a
+#define PAGE_SIZE	0x20U	//32 words
+
+#elif defined __AVR_ATmega168__
+#define SIG2	0x94
+#define SIG3	0x06
+#define PAGE_SIZE	0x40U	//64 words
+
+#elif defined __AVR_ATmega162__
+#define SIG2	0x94
+#define SIG3	0x04
+#define PAGE_SIZE	0x40U	//64 words
+
+#elif defined __AVR_ATmega163__
+#define SIG2	0x94
+#define SIG3	0x02
+#define PAGE_SIZE	0x40U	//64 words
+
+#elif defined __AVR_ATmega169__
+#define SIG2	0x94
+#define SIG3	0x05
+#define PAGE_SIZE	0x40U	//64 words
+
+#elif defined __AVR_ATmega8515__
+#define SIG2	0x93
+#define SIG3	0x06
+#define PAGE_SIZE	0x20U	//32 words
+
+#elif defined __AVR_ATmega8535__
+#define SIG2	0x93
+#define SIG3	0x08
+#define PAGE_SIZE	0x20U	//32 words
+#endif
+
+
+/* function prototypes */
+void putch(char);
+char getch(void);
+void getNch(uint8_t);
+void byte_response(uint8_t);
+void nothing_response(void);
+char gethex(void);
+void puthex(char);
+void flash_led(uint8_t);
+
+/* some variables */
+union address_union {
+    uint16_t word;
+    uint8_t  byte[2];
+} address;
+
+union length_union {
+    uint16_t word;
+    uint8_t  byte[2];
+} length;
+
+struct flags_struct {
+    unsigned eeprom : 1;
+    unsigned rampz  : 1;
+} flags;
+
+uint8_t buff[256];
+uint8_t address_high;
+
+uint8_t pagesz=0x80;
+
+uint8_t i;
+uint8_t bootuart = 0;
+
+uint8_t error_count = 0;
+
+void (*app_start)(void) = 0x0000;
+
+
+/* main program starts here */
+int main(void)
+{
+    uint8_t ch,ch2;
+    uint16_t w;
+
+    asm volatile("nop\n\t");
+
+    /* set pin direction for bootloader pin and enable pullup */
+    /* for ATmega128, two pins need to be initialized */
+#ifdef __AVR_ATmega128__
+    BL_DDR &= ~_BV(BL0);
+    BL_DDR &= ~_BV(BL1);
+    BL_PORT |= _BV(BL0);
+    BL_PORT |= _BV(BL1);
+#else
+    /* We run the bootloader regardless of the state of this pin.  Thus, don't
+    put it in a different state than the other pins.  --DAM, 070709
+    BL_DDR &= ~_BV(BL);
+    BL_PORT |= _BV(BL);
+    */
+#endif
+
+
+#ifdef __AVR_ATmega128__
+    /* check which UART should be used for booting */
+    if(bit_is_clear(BL_PIN, BL0)) {
+      bootuart = 1;
+    }
+    else if(bit_is_clear(BL_PIN, BL1)) {
+      bootuart = 2;
+    }
+#endif
+
+    /* check if flash is programmed already, if not start bootloader anyway */
+    if(pgm_read_byte_near(0x0000) != 0xFF) {
+
+#ifdef __AVR_ATmega128__
+	/* no UART was selected, start application */
+	if(!bootuart) {
+          app_start();
+	}
+#else
+	/* check if bootloader pin is set low */
+	/* we don't start this part neither for the m8, nor m168 */
+	//if(bit_is_set(BL_PIN, BL)) {
+    //      app_start();
+    //    }
+#endif
+    }
+
+#ifdef __AVR_ATmega128__    
+    /* no bootuart was selected, default to uart 0 */
+    if(!bootuart) {
+      bootuart = 1;
+    }
+#endif
+
+
+    /* initialize UART(s) depending on CPU defined */
+#ifdef __AVR_ATmega128__
+    if(bootuart == 1) {
+	UBRR0L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
+	UBRR0H = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
+	UCSR0A = 0x00;
+	UCSR0C = 0x06;
+	UCSR0B = _BV(TXEN0)|_BV(RXEN0);
+    }
+    if(bootuart == 2) {
+	UBRR1L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
+	UBRR1H = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
+	UCSR1A = 0x00;
+	UCSR1C = 0x06;
+	UCSR1B = _BV(TXEN1)|_BV(RXEN1);
+    }
+#elif defined __AVR_ATmega163__
+    UBRR = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
+    UBRRHI = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
+    UCSRA = 0x00;
+    UCSRB = _BV(TXEN)|_BV(RXEN);	
+#elif defined __AVR_ATmega168__
+    UBRR0L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
+    UBRR0H = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
+    UCSR0B = (1<<RXEN0) | (1<<TXEN0);
+    UCSR0C = (1<<UCSZ00) | (1<<UCSZ01);
+
+    /* Enable internal pull-up resistor on pin D0 (RX), in order
+    to supress line noise that prevents the bootloader from
+    timing out (DAM: 20070509) */
+    DDRD &= ~_BV(PIND0);
+    PORTD |= _BV(PIND0);
+#elif defined __AVR_ATmega8__
+  /* m8 */
+  UBRRH = (((F_CPU/BAUD_RATE)/16)-1)>>8; 	// set baud rate
+  UBRRL = (((F_CPU/BAUD_RATE)/16)-1);
+  UCSRB = (1<<RXEN)|(1<<TXEN);  // enable Rx & Tx
+  UCSRC = (1<<URSEL)|(1<<UCSZ1)|(1<<UCSZ0);  // config USART; 8N1
+#else
+    /* m16,m32,m169,m8515,m8535 */
+    UBRRL = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1);
+    UBRRH = (F_CPU/(BAUD_RATE*16L)-1) >> 8;
+    UCSRA = 0x00;
+    UCSRC = 0x06;
+    UCSRB = _BV(TXEN)|_BV(RXEN);
+#endif
+
+    /* set LED pin as output */
+    LED_DDR |= _BV(LED);
+
+
+    /* flash onboard LED to signal entering of bootloader */
+#ifdef __AVR_ATmega128__
+    // 4x for UART0, 5x for UART1
+    flash_led(NUM_LED_FLASHES + bootuart);
+#else
+    flash_led(NUM_LED_FLASHES);
+#endif
+    
+    /* 20050803: by DojoCorp, this is one of the parts provoking the
+                 system to stop listening, cancelled from the original */
+    //putch('\0');
+
+
+    /* forever loop */
+    for (;;) {
+
+	/* get character from UART */
+	ch = getch();
+
+	/* A bunch of if...else if... gives smaller code than switch...case ! */
+
+	/* Hello is anyone home ? */ 
+	if(ch=='0') {
+	    nothing_response();
+	}
+
+
+	/* Request programmer ID */
+	/* Not using PROGMEM string due to boot block in m128 being beyond 64kB boundry  */
+	/* Would need to selectively manipulate RAMPZ, and it's only 9 characters anyway so who cares.  */
+	else if(ch=='1') {
+	    if (getch() == ' ') {
+		putch(0x14);
+		putch('A');
+		putch('V');
+		putch('R');
+		putch(' ');
+		putch('I');
+		putch('S');
+		putch('P');
+		putch(0x10);
+	    } else {
+		if (++error_count == MAX_ERROR_COUNT)
+		    app_start();
+	    }
+	}
+
+
+	/* AVR ISP/STK500 board commands  DON'T CARE so default nothing_response */
+	else if(ch=='@') {
+	    ch2 = getch();
+	    if (ch2>0x85) getch();
+	    nothing_response();
+	}
+
+
+	/* AVR ISP/STK500 board requests */
+	else if(ch=='A') {
+	    ch2 = getch();
+	    if(ch2==0x80) byte_response(HW_VER);		// Hardware version
+	    else if(ch2==0x81) byte_response(SW_MAJOR);	// Software major version
+	    else if(ch2==0x82) byte_response(SW_MINOR);	// Software minor version
+	    else if(ch2==0x98) byte_response(0x03);		// Unknown but seems to be required by avr studio 3.56
+	    else byte_response(0x00);				// Covers various unnecessary responses we don't care about
+	}
+
+
+	/* Device Parameters  DON'T CARE, DEVICE IS FIXED  */
+	else if(ch=='B') {
+	    getNch(20);
+	    nothing_response();
+	}
+
+
+	/* Parallel programming stuff  DON'T CARE  */
+	else if(ch=='E') {
+	    getNch(5);
+	    nothing_response();
+	}
+
+
+	/* Enter programming mode  */
+	else if(ch=='P') {
+	    nothing_response();
+	}
+
+
+	/* Leave programming mode  */
+	else if(ch=='Q') {
+	    nothing_response();
+	}
+
+
+	/* Erase device, don't care as we will erase one page at a time anyway.  */
+	else if(ch=='R') {
+	    nothing_response();
+	}
+
+
+	/* Set address, little endian. EEPROM in bytes, FLASH in words  */
+	/* Perhaps extra address bytes may be added in future to support > 128kB FLASH.  */
+	/* This might explain why little endian was used here, big endian used everywhere else.  */
+	else if(ch=='U') {
+	    address.byte[0] = getch();
+	    address.byte[1] = getch();
+	    nothing_response();
+	}
+
+
+	/* Universal SPI programming command, disabled.  Would be used for fuses and lock bits.  */
+	else if(ch=='V') {
+	    getNch(4);
+	    byte_response(0x00);
+	}
+
+
+	/* Write memory, length is big endian and is in bytes  */
+	else if(ch=='d') {
+	    length.byte[1] = getch();
+	    length.byte[0] = getch();
+	    flags.eeprom = 0;
+	    if (getch() == 'E') flags.eeprom = 1;
+	    for (w=0;w<length.word;w++) {
+		buff[w] = getch();	                        // Store data in buffer, can't keep up with serial data stream whilst programming pages
+	    }
+	    if (getch() == ' ') {
+		if (flags.eeprom) {		                //Write to EEPROM one byte at a time
+		    for(w=0;w<length.word;w++) {
+#ifdef __AVR_ATmega168__
+			while(EECR & (1<<EEPE));
+			EEAR = (uint16_t)(void *)address.word;
+			EEDR = buff[w];
+			EECR |= (1<<EEMPE);
+			EECR |= (1<<EEPE);
+#else
+			eeprom_write_byte((void *)address.word,buff[w]);
+#endif
+			address.word++;
+		    }			
+		}
+		else {					        //Write to FLASH one page at a time
+		    if (address.byte[1]>127) address_high = 0x01;	//Only possible with m128, m256 will need 3rd address byte. FIXME
+		    else address_high = 0x00;
+#ifdef __AVR_ATmega128__
+		    RAMPZ = address_high;
+#endif
+		    address.word = address.word << 1;	        //address * 2 -> byte location
+		    /* if ((length.byte[0] & 0x01) == 0x01) length.word++;	//Even up an odd number of bytes */
+		    if ((length.byte[0] & 0x01)) length.word++;	//Even up an odd number of bytes
+		    cli();					//Disable interrupts, just to be sure
+			// HACKME: EEPE used to be EEWE
+		    while(bit_is_set(EECR,EEPE));			//Wait for previous EEPROM writes to complete
+		    asm volatile(
+				 "clr	r17		\n\t"	//page_word_count
+				 "lds	r30,address	\n\t"	//Address of FLASH location (in bytes)
+				 "lds	r31,address+1	\n\t"
+				 "ldi	r28,lo8(buff)	\n\t"	//Start of buffer array in RAM
+				 "ldi	r29,hi8(buff)	\n\t"
+				 "lds	r24,length	\n\t"	//Length of data to be written (in bytes)
+				 "lds	r25,length+1	\n\t"
+				 "length_loop:		\n\t"	//Main loop, repeat for number of words in block							 							 
+				 "cpi	r17,0x00	\n\t"	//If page_word_count=0 then erase page
+				 "brne	no_page_erase	\n\t"						 
+				 "wait_spm1:		\n\t"
+				 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+				 "andi	r16,1           \n\t"
+				 "cpi	r16,1           \n\t"
+				 "breq	wait_spm1       \n\t"
+				 "ldi	r16,0x03	\n\t"	//Erase page pointed to by Z
+				 "sts	%0,r16		\n\t"
+				 "spm			\n\t"							 
+#ifdef __AVR_ATmega163__
+				 ".word 0xFFFF		\n\t"
+				 "nop			\n\t"
+#endif
+				 "wait_spm2:		\n\t"
+				 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+				 "andi	r16,1           \n\t"
+				 "cpi	r16,1           \n\t"
+				 "breq	wait_spm2       \n\t"									 
+
+				 "ldi	r16,0x11	\n\t"	//Re-enable RWW section
+				 "sts	%0,r16		\n\t"						 			 
+				 "spm			\n\t"
+#ifdef __AVR_ATmega163__
+				 ".word 0xFFFF		\n\t"
+				 "nop			\n\t"
+#endif
+				 "no_page_erase:		\n\t"							 
+				 "ld	r0,Y+		\n\t"	//Write 2 bytes into page buffer
+				 "ld	r1,Y+		\n\t"							 
+							 
+				 "wait_spm3:		\n\t"
+				 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+				 "andi	r16,1           \n\t"
+				 "cpi	r16,1           \n\t"
+				 "breq	wait_spm3       \n\t"
+				 "ldi	r16,0x01	\n\t"	//Load r0,r1 into FLASH page buffer
+				 "sts	%0,r16		\n\t"
+				 "spm			\n\t"
+							 
+				 "inc	r17		\n\t"	//page_word_count++
+				 "cpi r17,%1	        \n\t"
+				 "brlo	same_page	\n\t"	//Still same page in FLASH
+				 "write_page:		\n\t"
+				 "clr	r17		\n\t"	//New page, write current one first
+				 "wait_spm4:		\n\t"
+				 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+				 "andi	r16,1           \n\t"
+				 "cpi	r16,1           \n\t"
+				 "breq	wait_spm4       \n\t"
+#ifdef __AVR_ATmega163__
+				 "andi	r30,0x80	\n\t"	// m163 requires Z6:Z1 to be zero during page write
+#endif							 							 
+				 "ldi	r16,0x05	\n\t"	//Write page pointed to by Z
+				 "sts	%0,r16		\n\t"
+				 "spm			\n\t"
+#ifdef __AVR_ATmega163__
+				 ".word 0xFFFF		\n\t"
+				 "nop			\n\t"
+				 "ori	r30,0x7E	\n\t"	// recover Z6:Z1 state after page write (had to be zero during write)
+#endif
+				 "wait_spm5:		\n\t"
+				 "lds	r16,%0		\n\t"	//Wait for previous spm to complete
+				 "andi	r16,1           \n\t"
+				 "cpi	r16,1           \n\t"
+				 "breq	wait_spm5       \n\t"									 
+				 "ldi	r16,0x11	\n\t"	//Re-enable RWW section
+				 "sts	%0,r16		\n\t"						 			 
+				 "spm			\n\t"					 		 
+#ifdef __AVR_ATmega163__
+				 ".word 0xFFFF		\n\t"
+				 "nop			\n\t"
+#endif
+				 "same_page:		\n\t"							 
+				 "adiw	r30,2		\n\t"	//Next word in FLASH
+				 "sbiw	r24,2		\n\t"	//length-2
+				 "breq	final_write	\n\t"	//Finished
+				 "rjmp	length_loop	\n\t"
+				 "final_write:		\n\t"
+				 "cpi	r17,0		\n\t"
+				 "breq	block_done	\n\t"
+				 "adiw	r24,2		\n\t"	//length+2, fool above check on length after short page write
+				 "rjmp	write_page	\n\t"
+				 "block_done:		\n\t"
+				 "clr	__zero_reg__	\n\t"	//restore zero register
+#if defined __AVR_ATmega168__
+				 : "=m" (SPMCSR) : "M" (PAGE_SIZE) : "r0","r16","r17","r24","r25","r28","r29","r30","r31"
+#else
+				 : "=m" (SPMCR) : "M" (PAGE_SIZE) : "r0","r16","r17","r24","r25","r28","r29","r30","r31"
+#endif
+				 );
+		    /* Should really add a wait for RWW section to be enabled, don't actually need it since we never */
+		    /* exit the bootloader without a power cycle anyhow */
+		}
+		putch(0x14);
+		putch(0x10);
+	    } else {
+		if (++error_count == MAX_ERROR_COUNT)
+		    app_start();
+	    }		
+	}
+    
+
+        /* Read memory block mode, length is big endian.  */
+        else if(ch=='t') {
+	    length.byte[1] = getch();
+	    length.byte[0] = getch();
+#if defined __AVR_ATmega128__
+	    if (address.word>0x7FFF) flags.rampz = 1;		// No go with m256, FIXME
+	    else flags.rampz = 0;
+#endif
+	    if (getch() == 'E') flags.eeprom = 1;
+	    else {
+		flags.eeprom = 0;
+		address.word = address.word << 1;	        // address * 2 -> byte location
+	    }
+	    if (getch() == ' ') {		                // Command terminator
+		putch(0x14);
+		for (w=0;w < length.word;w++) {		        // Can handle odd and even lengths okay
+		    if (flags.eeprom) {	                        // Byte access EEPROM read
+#ifdef __AVR_ATmega168__
+			while(EECR & (1<<EEPE));
+			EEAR = (uint16_t)(void *)address.word;
+			EECR |= (1<<EERE);
+			putch(EEDR);
+#else
+			putch(eeprom_read_byte((void *)address.word));
+#endif
+			address.word++;
+		    }
+		    else {
+
+			if (!flags.rampz) putch(pgm_read_byte_near(address.word));
+#if defined __AVR_ATmega128__
+			else putch(pgm_read_byte_far(address.word + 0x10000));
+			// Hmmmm, yuck  FIXME when m256 arrvies
+#endif
+			address.word++;
+		    }
+		}
+		putch(0x10);
+	    }
+	}
+
+
+        /* Get device signature bytes  */
+        else if(ch=='u') {
+	    if (getch() == ' ') {
+		putch(0x14);
+		putch(SIG1);
+		putch(SIG2);
+		putch(SIG3);
+		putch(0x10);
+	    } else {
+		if (++error_count == MAX_ERROR_COUNT)
+		    app_start();
+	    }
+	}
+
+
+        /* Read oscillator calibration byte */
+        else if(ch=='v') {
+	    byte_response(0x00);
+	}
+
+
+#ifdef MONITOR
+
+	/* here come the extended monitor commands by Erik Lins */
+
+	/* check for three times exclamation mark pressed */
+	else if(ch=='!') {
+	    ch = getch();
+	    if(ch=='!') {
+		ch = getch();
+		if(ch=='!') {
+
+#ifdef __AVR_ATmega128__
+		    uint16_t extaddr;
+#endif
+		    uint8_t addrl, addrh;
+
+#ifdef CRUMB128
+		    PGM_P welcome = {"ATmegaBOOT / Crumb128 - (C) J.P.Kyle, E.Lins - 050815\n\r"};
+#elif defined PROBOMEGA128
+		    PGM_P welcome = {"ATmegaBOOT / PROBOmega128 - (C) J.P.Kyle, E.Lins - 050815\n\r"};
+#elif defined SAVVY128
+		    PGM_P welcome = {"ATmegaBOOT / Savvy128 - (C) J.P.Kyle, E.Lins - 050815\n\r"};
+#endif
+
+		    /* turn on LED */
+		    LED_DDR |= _BV(LED);
+		    LED_PORT &= ~_BV(LED);
+
+		    /* print a welcome message and command overview */
+		    for(i=0; welcome[i] != '\0'; ++i) {
+			putch(welcome[i]);
+		    }
+
+		    /* test for valid commands */
+		    for(;;) {
+			putch('\n');
+			putch('\r');
+			putch(':');
+			putch(' ');
+
+			ch = getch();
+			putch(ch);
+
+			/* toggle LED */
+			if(ch == 't') {
+			    if(bit_is_set(LED_PIN,LED)) {
+				LED_PORT &= ~_BV(LED);
+				putch('1');
+			    } else {
+				LED_PORT |= _BV(LED);
+				putch('0');
+			    }
+
+			} 
+
+			/* read byte from address */
+			else if(ch == 'r') {
+			    ch = getch(); putch(ch);
+			    addrh = gethex();
+			    addrl = gethex();
+			    putch('=');
+			    ch = *(uint8_t *)((addrh << 8) + addrl);
+			    puthex(ch);
+			}
+
+			/* write a byte to address  */
+			else if(ch == 'w') {
+			    ch = getch(); putch(ch);
+			    addrh = gethex();
+			    addrl = gethex();
+			    ch = getch(); putch(ch);
+			    ch = gethex();
+			    *(uint8_t *)((addrh << 8) + addrl) = ch;
+
+			}
+
+			/* read from uart and echo back */
+			else if(ch == 'u') {
+			    for(;;) {
+				putch(getch());
+			    }
+			}
+#ifdef __AVR_ATmega128__
+			/* external bus loop  */
+			else if(ch == 'b') {
+			    putch('b');
+			    putch('u');
+			    putch('s');
+			    MCUCR = 0x80;
+			    XMCRA = 0;
+			    XMCRB = 0;
+			    extaddr = 0x1100;
+			    for(;;) {
+				ch = *(volatile uint8_t *)extaddr;
+				if(++extaddr == 0) {
+				    extaddr = 0x1100;
+				}
+			    }
+			}
+#endif
+
+			else if(ch == 'j') {
+			    app_start();
+			}
+
+		    }
+		    /* end of monitor functions */
+
+		}
+	    }
+	}
+	/* end of monitor */
+#endif
+	else if (++error_count == MAX_ERROR_COUNT) {
+	    app_start();
+	}
+    }
+    /* end of forever loop */
+
+}
+
+
+char gethex(void) {
+    char ah,al;
+
+    ah = getch(); putch(ah);
+    al = getch(); putch(al);
+    if(ah >= 'a') {
+	ah = ah - 'a' + 0x0a;
+    } else if(ah >= '0') {
+	ah -= '0';
+    }
+    if(al >= 'a') {
+	al = al - 'a' + 0x0a;
+    } else if(al >= '0') {
+	al -= '0';
+    }
+    return (ah << 4) + al;
+}
+
+
+void puthex(char ch) {
+    char ah,al;
+
+    ah = (ch & 0xf0) >> 4;
+    if(ah >= 0x0a) {
+	ah = ah - 0x0a + 'a';
+    } else {
+	ah += '0';
+    }
+    al = (ch & 0x0f);
+    if(al >= 0x0a) {
+	al = al - 0x0a + 'a';
+    } else {
+	al += '0';
+    }
+    putch(ah);
+    putch(al);
+}
+
+
+void putch(char ch)
+{
+#ifdef __AVR_ATmega128__
+    if(bootuart == 1) {
+	while (!(UCSR0A & _BV(UDRE0)));
+	UDR0 = ch;
+    }
+    else if (bootuart == 2) {
+	while (!(UCSR1A & _BV(UDRE1)));
+	UDR1 = ch;
+    }
+#elif defined __AVR_ATmega168__
+    while (!(UCSR0A & _BV(UDRE0)));
+    UDR0 = ch;
+#else
+    /* m8,16,32,169,8515,8535,163 */
+    while (!(UCSRA & _BV(UDRE)));
+    UDR = ch;
+#endif
+}
+
+
+char getch(void)
+{
+#ifdef __AVR_ATmega128__
+    if(bootuart == 1) {
+	while(!(UCSR0A & _BV(RXC0)));
+	return UDR0;
+    }
+    else if(bootuart == 2) {
+	while(!(UCSR1A & _BV(RXC1)));
+	return UDR1;
+    }
+    return 0;
+#elif defined __AVR_ATmega168__
+    uint32_t count = 0;
+    while(!(UCSR0A & _BV(RXC0))){
+    	/* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/               
+    	/* HACKME:: here is a good place to count times*/
+    	count++;
+    	if (count > MAX_TIME_COUNT)
+    		app_start();
+     }
+    return UDR0;
+#else
+    /* m8,16,32,169,8515,8535,163 */
+    uint32_t count = 0;
+    while(!(UCSRA & _BV(RXC))){
+    	/* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/               
+    	/* HACKME:: here is a good place to count times*/
+    	count++;
+    	if (count > MAX_TIME_COUNT)
+    		app_start();
+     }
+    return UDR;
+#endif
+}
+
+
+void getNch(uint8_t count)
+{
+    uint8_t i;
+    for(i=0;i<count;i++) {
+#ifdef __AVR_ATmega128__
+	if(bootuart == 1) {
+	    while(!(UCSR0A & _BV(RXC0)));
+	    UDR0;
+	} 
+	else if(bootuart == 2) {
+	    while(!(UCSR1A & _BV(RXC1)));
+	    UDR1;
+	}
+#elif defined __AVR_ATmega168__
+	while(!(UCSR0A & _BV(RXC0)));
+	UDR0;
+#else
+	/* m8,16,32,169,8515,8535,163 */
+   	/* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/               
+	//while(!(UCSRA & _BV(RXC)));
+	//UDR;
+    uint8_t i;
+    for(i=0;i<count;i++) {
+    	getch(); // need to handle time out
+    }
+#endif		
+    }
+}
+
+
+void byte_response(uint8_t val)
+{
+    if (getch() == ' ') {
+	putch(0x14);
+	putch(val);
+	putch(0x10);
+    } else {
+	if (++error_count == MAX_ERROR_COUNT)
+	    app_start();
+    }
+}
+
+
+void nothing_response(void)
+{
+    if (getch() == ' ') {
+	putch(0x14);
+	putch(0x10);
+    } else {
+	if (++error_count == MAX_ERROR_COUNT)
+	    app_start();
+    }
+}
+
+void flash_led(uint8_t count)
+{
+    /* flash onboard LED three times to signal entering of bootloader */
+	/* l needs to be volatile or the delay loops below might get
+	optimized away if compiling with optimizations (DAM). */
+    volatile uint32_t l;
+
+    if (count == 0) {
+      count = 3;
+    }
+    
+    for (i = 0; i < count; ++i) {
+	LED_PORT |= _BV(LED);
+	for(l = 0; l < (F_CPU / 1000); ++l);
+	LED_PORT &= ~_BV(LED);
+	for(l = 0; l < (F_CPU / 1000); ++l);
+    }
+}
+
+
+/* end of file ATmegaBOOT.c */
diff --git a/bootloaders/lilypad/src/Makefile b/bootloaders/lilypad/src/Makefile
new file mode 100644
index 0000000..516d5b2
--- /dev/null
+++ b/bootloaders/lilypad/src/Makefile
@@ -0,0 +1,84 @@
+# Makefile for ATmegaBOOT
+# E.Lins, 18.7.2005
+# $Id$
+
+# Instructions
+#
+# To build the bootloader for the LilyPad:
+# make lily
+
+
+# program name should not be changed...
+PROGRAM    = ATmegaBOOT_168
+
+# enter the target CPU frequency
+AVR_FREQ   = 8000000L
+
+# enter the parameters for the avrdude isp tool
+ISPTOOL	   = stk500v2
+ISPPORT	   = usb
+ISPSPEED   = -b 115200
+
+MCU_TARGET = atmega168
+LDSECTION  = --section-start=.text=0x3800
+
+# the efuse should really be 0xf8; since, however, only the lower
+# three bits of that byte are used on the atmega168, avrdude gets
+# confused if you specify 1's for the higher bits, see:
+# http://tinker.it/now/2007/02/24/the-tale-of-avrdude-atmega168-and-extended-bits-fuses/
+#
+# similarly, the lock bits should be 0xff instead of 0x3f (to
+# unlock the bootloader section) and 0xcf instead of 0x0f (to
+# lock it), but since the high two bits of the lock byte are
+# unused, avrdude would get confused.
+ISPFUSES    = avrdude -c $(ISPTOOL) -p m168 -P $(ISPPORT) $(ISPSPEED) -e -u -U lock:w:0x3f:m -U efuse:w:0x00:m -U hfuse:w:0xdd:m -U lfuse:w:0xff:m
+ISPFLASH    = avrdude -c $(ISPTOOL) -p m168 -P $(ISPPORT) $(ISPSPEED) -U flash:w:$(PROGRAM)_$(TARGET).hex -U lock:w:0x0f:m
+
+
+OBJ        = $(PROGRAM).o
+OPTIMIZE   = -O2
+
+DEFS       = 
+LIBS       =
+
+CC         = avr-gcc
+
+
+# Override is only needed by avr-lib build system.
+
+override CFLAGS        = -g -Wall $(OPTIMIZE) -mmcu=$(MCU_TARGET) -DF_CPU=$(AVR_FREQ) $(DEFS)
+override LDFLAGS       = -Wl,$(LDSECTION)
+#override LDFLAGS       = -Wl,-Map,$(PROGRAM).map,$(LDSECTION)
+
+OBJCOPY        = avr-objcopy
+OBJDUMP        = avr-objdump
+
+all:
+
+lily: CFLAGS += '-DMAX_TIME_COUNT=F_CPU>>1' '-DNUM_LED_FLASHES=3'
+lily: $(PROGRAM).hex
+
+$(PROGRAM).hex: $(PROGRAM).elf
+	$(OBJCOPY) -j .text -j .data -O ihex $< $@
+	
+$(PROGRAM).elf: $(OBJ)
+	$(CC) $(CFLAGS) $(LDFLAGS) -o $@ $^ $(LIBS)
+	
+$(OBJ): 
+	avr-gcc $(CFLAGS) $(LDFLAGS) -c -g -O2 -Wall -mmcu=atmega168 ATmegaBOOT.c -o ATmegaBOOT_168.o
+
+%.lst: %.elf
+	$(OBJDUMP) -h -S $< > $@
+
+%.srec: %.elf
+	$(OBJCOPY) -j .text -j .data -O srec $< $@
+
+%.bin: %.elf
+	$(OBJCOPY) -j .text -j .data -O binary $< $@
+
+clean:
+	rm -rf *.o *.elf *.lst *.map *.sym *.lss *.eep *.srec *.bin *.hex
+	
+install:
+	avrdude -p m168 -c stk500v2 -P /dev/cu.USA19H1b1P1.1 -e -u -U lock:w:0x3f:m -U efuse:w:0x00:m -U hfuse:w:0xdd:m -U lfuse:w:0xe2:m 
+	avrdude -p m168 -c stk500v2 -P /dev/cu.USA19H1b1P1.1 -e -u -U flash:w:ATmegaBOOT_168.hex  -U lock:w:0x0f:m