aboutsummaryrefslogtreecommitdiff
path: root/bootloaders/optiboot/optiboot.c
diff options
context:
space:
mode:
Diffstat (limited to 'bootloaders/optiboot/optiboot.c')
-rw-r--r--bootloaders/optiboot/optiboot.c288
1 files changed, 176 insertions, 112 deletions
diff --git a/bootloaders/optiboot/optiboot.c b/bootloaders/optiboot/optiboot.c
index c7d817a..4b4a10a 100644
--- a/bootloaders/optiboot/optiboot.c
+++ b/bootloaders/optiboot/optiboot.c
@@ -1,6 +1,11 @@
/**********************************************************/
/* Optiboot bootloader for Arduino */
/* */
+/* http://optiboot.googlecode.com */
+/* */
+/* Arduino-maintained version : See README.TXT */
+/* http://code.google.com/p/arduino/ */
+/* */
/* Heavily optimised bootloader that is faster and */
/* smaller than the Arduino standard bootloader */
/* */
@@ -10,6 +15,8 @@
/* Higher baud rate speeds up programming */
/* Written almost entirely in C */
/* Customisable timeout with accurate timeconstant */
+/* Optional virtual UART. No hardware UART required. */
+/* Optional virtual boot partition for devices without. */
/* */
/* What you lose: */
/* Implements a skeleton STK500 protocol which is */
@@ -18,12 +25,19 @@
/* High baud rate breaks compatibility with standard */
/* Arduino flash settings */
/* */
-/* Currently supports: */
-/* ATmega168 based devices (Diecimila etc) */
+/* Fully supported: */
+/* ATmega168 based devices (Diecimila etc) */
/* ATmega328P based devices (Duemilanove etc) */
/* */
+/* Alpha test */
+/* ATmega1280 based devices (Arduino Mega) */
+/* */
+/* Work in progress: */
+/* ATmega644P based devices (Sanguino) */
+/* ATtiny84 based devices (Luminet) */
+/* */
/* Does not support: */
-/* ATmega1280 based devices (eg. Mega) */
+/* USB based devices (eg. Teensy) */
/* */
/* Assumptions: */
/* The code makes several assumptions that reduce the */
@@ -64,102 +78,85 @@
/* */
/**********************************************************/
+
+/**********************************************************/
+/* */
+/* Optional defines: */
+/* */
+/**********************************************************/
+/* */
+/* BIG_BOOT: */
+/* Build a 1k bootloader, not 512 bytes. This turns on */
+/* extra functionality. */
+/* */
+/* BAUD_RATE: */
+/* Set bootloader baud rate. */
+/* */
+/* LUDICROUS_SPEED: */
+/* 230400 baud :-) */
+/* */
+/* SOFT_UART: */
+/* Use AVR305 soft-UART instead of hardware UART. */
+/* */
+/* LED_START_FLASHES: */
+/* Number of LED flashes on bootup. */
+/* */
+/* LED_DATA_FLASH: */
+/* Flash LED when transferring data. For boards without */
+/* TX or RX LEDs, or for people who like blinky lights. */
+/* */
+/* SUPPORT_EEPROM: */
+/* Support reading and writing from EEPROM. This is not */
+/* used by Arduino, so off by default. */
+/* */
+/* TIMEOUT_MS: */
+/* Bootloader timeout period, in milliseconds. */
+/* 500,1000,2000,4000,8000 supported. */
+/* */
+/**********************************************************/
+
#include <inttypes.h>
#include <avr/io.h>
#include <avr/pgmspace.h>
-#include <avr/boot.h>
-//#define LED_DATA_FLASH
+// <avr/boot.h> uses sts instructions, but this version uses out instructions
+// This saves cycles and program memory.
+#include "boot.h"
+
+
+// We don't use <avr/wdt.h> as those routines have interrupt overhead we don't need.
+
+#include "pin_defs.h"
+#include "stk500.h"
#ifndef LED_START_FLASHES
#define LED_START_FLASHES 0
#endif
-/* Build-time variables */
-/* BAUD_RATE Programming baud rate */
-/* LED_NO_FLASHES Number of LED flashes on boot */
-/* FLASH_TIME_MS Duration of each LED flash */
-/* BOOT_TIMEOUT_MS Serial port wait time before exiting bootloader */
+#ifdef LUDICROUS_SPEED
+#define BAUD_RATE 230400L
+#endif
-/* set the UART baud rate */
+/* set the UART baud rate defaults */
#ifndef BAUD_RATE
-#define BAUD_RATE 19200
+#if F_CPU >= 8000000L
+#define BAUD_RATE 115200L // Highest rate Avrdude win32 will support
+#elsif F_CPU >= 1000000L
+#define BAUD_RATE 9600L // 19200 also supported, but with significant error
+#elsif F_CPU >= 128000L
+#define BAUD_RATE 4800L // Good for 128kHz internal RC
+#else
+#define BAUD_RATE 1200L // Good even at 32768Hz
+#endif
#endif
-#if defined(__AVR_ATmega168__) || defined(__AVR_ATmega328P__)
-/* Onboard LED is connected to pin PB5 in Arduino NG, Diecimila, and Duemilanove */
-#define LED_DDR DDRB
-#define LED_PORT PORTB
-#define LED_PIN PINB
-#define LED PINB5
-
-/* Ports for soft UART */
-#ifdef SOFT_UART
-#define UART_PORT PORTD
-#define UART_PIN PIND
-#define UART_DDR DDRD
-#define UART_TX_BIT 1
-#define UART_RX_BIT 0
+/* Switch in soft UART for hard baud rates */
+#if (F_CPU/BAUD_RATE) > 280 // > 57600 for 16MHz
+#ifndef SOFT_UART
+#define SOFT_UART
#endif
#endif
-#if defined(__AVR_ATtiny84__)
-/* Onboard LED is connected to pin PB5 in Arduino NG, Diecimila, and Duemilanove */
-#define LED_DDR DDRA
-#define LED_PORT PORTA
-#define LED_PIN PINA
-#define LED PINA4
-
-/* Ports for soft UART - left port only for now*/
-#ifdef SOFT_UART
-#define UART_PORT PORTA
-#define UART_PIN PINA
-#define UART_DDR DDRA
-#define UART_TX_BIT 2
-#define UART_RX_BIT 3
-#endif
-#endif
-
-/* STK500 constants list, from AVRDUDE */
-#define STK_OK 0x10
-#define STK_FAILED 0x11 // Not used
-#define STK_UNKNOWN 0x12 // Not used
-#define STK_NODEVICE 0x13 // Not used
-#define STK_INSYNC 0x14 // ' '
-#define STK_NOSYNC 0x15 // Not used
-#define ADC_CHANNEL_ERROR 0x16 // Not used
-#define ADC_MEASURE_OK 0x17 // Not used
-#define PWM_CHANNEL_ERROR 0x18 // Not used
-#define PWM_ADJUST_OK 0x19 // Not used
-#define CRC_EOP 0x20 // 'SPACE'
-#define STK_GET_SYNC 0x30 // '0'
-#define STK_GET_SIGN_ON 0x31 // '1'
-#define STK_SET_PARAMETER 0x40 // '@'
-#define STK_GET_PARAMETER 0x41 // 'A'
-#define STK_SET_DEVICE 0x42 // 'B'
-#define STK_SET_DEVICE_EXT 0x45 // 'E'
-#define STK_ENTER_PROGMODE 0x50 // 'P'
-#define STK_LEAVE_PROGMODE 0x51 // 'Q'
-#define STK_CHIP_ERASE 0x52 // 'R'
-#define STK_CHECK_AUTOINC 0x53 // 'S'
-#define STK_LOAD_ADDRESS 0x55 // 'U'
-#define STK_UNIVERSAL 0x56 // 'V'
-#define STK_PROG_FLASH 0x60 // '`'
-#define STK_PROG_DATA 0x61 // 'a'
-#define STK_PROG_FUSE 0x62 // 'b'
-#define STK_PROG_LOCK 0x63 // 'c'
-#define STK_PROG_PAGE 0x64 // 'd'
-#define STK_PROG_FUSE_EXT 0x65 // 'e'
-#define STK_READ_FLASH 0x70 // 'p'
-#define STK_READ_DATA 0x71 // 'q'
-#define STK_READ_FUSE 0x72 // 'r'
-#define STK_READ_LOCK 0x73 // 's'
-#define STK_READ_PAGE 0x74 // 't'
-#define STK_READ_SIGN 0x75 // 'u'
-#define STK_READ_OSCCAL 0x76 // 'v'
-#define STK_READ_FUSE_EXT 0x77 // 'w'
-#define STK_READ_OSCCAL_EXT 0x78 // 'x'
-
/* Watchdog settings */
#define WATCHDOG_OFF (0)
#define WATCHDOG_16MS (_BV(WDE))
@@ -170,8 +167,10 @@
#define WATCHDOG_500MS (_BV(WDP2) | _BV(WDP0) | _BV(WDE))
#define WATCHDOG_1S (_BV(WDP2) | _BV(WDP1) | _BV(WDE))
#define WATCHDOG_2S (_BV(WDP2) | _BV(WDP1) | _BV(WDP0) | _BV(WDE))
+#ifndef __AVR_ATmega8__
#define WATCHDOG_4S (_BV(WDE3) | _BV(WDE))
#define WATCHDOG_8S (_BV(WDE3) | _BV(WDE0) | _BV(WDE))
+#endif
/* Function Prototypes */
/* The main function is in init9, which removes the interrupt vector table */
@@ -191,18 +190,41 @@ void uartDelay() __attribute__ ((naked));
#endif
void appStart() __attribute__ ((naked));
+#if defined(__AVR_ATmega168__)
+#define RAMSTART (0x100)
+#define NRWWSTART (0x3800)
+#elif defined(__AVR_ATmega328P__)
+#define RAMSTART (0x100)
+#define NRWWSTART (0x7000)
+#elif defined (__AVR_ATmega644P__)
+#define RAMSTART (0x100)
+#define NRWWSTART (0xE000)
+#elif defined(__AVR_ATtiny84__)
+#define RAMSTART (0x100)
+#define NRWWSTART (0x0000)
+#elif defined(__AVR_ATmega1280__)
+#define RAMSTART (0x200)
+#define NRWWSTART (0xE000)
+#elif defined(__AVR_ATmega8__) || defined(__AVR_ATmega88__)
+#define RAMSTART (0x100)
+#define NRWWSTART (0x1800)
+#endif
+
/* C zero initialises all global variables. However, that requires */
/* These definitions are NOT zero initialised, but that doesn't matter */
/* This allows us to drop the zero init code, saving us memory */
-#define buff ((uint8_t*)(0x100))
-#define address (*(uint16_t*)(0x200))
-#define length (*(uint8_t*)(0x202))
+#define buff ((uint8_t*)(RAMSTART))
+#define address (*(uint16_t*)(RAMSTART+SPM_PAGESIZE*2))
+#define length (*(uint8_t*)(RAMSTART+SPM_PAGESIZE*2+2))
#ifdef VIRTUAL_BOOT_PARTITION
-#define rstVect (*(uint16_t*)(0x204))
-#define wdtVect (*(uint16_t*)(0x206))
+#define rstVect (*(uint16_t*)(RAMSTART+SPM_PAGESIZE*2+4))
+#define wdtVect (*(uint16_t*)(RAMSTART+SPM_PAGESIZE*2+6))
#endif
+
/* main program starts here */
int main(void) {
+ uint8_t ch;
+
// After the zero init loop, this is the first code to run.
//
// This code makes the following assumptions:
@@ -212,29 +234,36 @@ int main(void) {
//
// If not, uncomment the following instructions:
// cli();
- // SP=RAMEND; // This is done by hardware reset
asm volatile ("clr __zero_reg__");
+#ifdef __AVR_ATmega8__
+ SP=RAMEND; // This is done by hardware reset
+#endif
- uint8_t ch;
+ // Adaboot no-wait mod
+ ch = MCUSR;
+ MCUSR = 0;
+ if (!(ch & _BV(EXTRF))) appStart();
#if LED_START_FLASHES > 0
// Set up Timer 1 for timeout counter
TCCR1B = _BV(CS12) | _BV(CS10); // div 1024
#endif
#ifndef SOFT_UART
+#ifdef __AVR_ATmega8__
+ UCSRA = _BV(U2X); //Double speed mode USART
+ UCSRB = _BV(RXEN) | _BV(TXEN); // enable Rx & Tx
+ UCSRC = _BV(URSEL) | _BV(UCSZ1) | _BV(UCSZ0); // config USART; 8N1
+ UBRRL = (uint8_t)( (F_CPU + BAUD_RATE * 4L) / (BAUD_RATE * 8L) - 1 );
+#else
UCSR0A = _BV(U2X0); //Double speed mode USART0
UCSR0B = _BV(RXEN0) | _BV(TXEN0);
UCSR0C = _BV(UCSZ00) | _BV(UCSZ01);
UBRR0L = (uint8_t)( (F_CPU + BAUD_RATE * 4L) / (BAUD_RATE * 8L) - 1 );
#endif
-
- // Adaboot no-wait mod
- ch = MCUSR;
- MCUSR = 0;
- if (!(ch & _BV(EXTRF))) appStart();
+#endif
// Set up watchdog to trigger after 500ms
- watchdogConfig(WATCHDOG_500MS);
+ watchdogConfig(WATCHDOG_1S);
/* Set LED pin as output */
LED_DDR |= _BV(LED);
@@ -269,9 +298,15 @@ int main(void) {
}
else if(ch == STK_LOAD_ADDRESS) {
// LOAD ADDRESS
- address = getch();
- address = (address & 0xff) | (getch() << 8);
- address += address; // Convert from word address to byte address
+ uint16_t newAddress;
+ newAddress = getch();
+ newAddress = (newAddress & 0xff) | (getch() << 8);
+#ifdef RAMPZ
+ // Transfer top bit to RAMPZ
+ RAMPZ = (newAddress & 0x8000) ? 1 : 0;
+#endif
+ newAddress += newAddress; // Convert from word address to byte address
+ address = newAddress;
verifySpace();
}
else if(ch == STK_UNIVERSAL) {
@@ -279,7 +314,7 @@ int main(void) {
getNch(4);
putch(0x00);
}
- /* Write memory, length is big endian and is in bytes */
+ /* Write memory, length is big endian and is in bytes */
else if(ch == STK_PROG_PAGE) {
// PROGRAM PAGE - we support flash programming only, not EEPROM
uint8_t *bufPtr;
@@ -287,14 +322,18 @@ int main(void) {
getLen();
- // Immediately start page erase - this will 4.5ms
- boot_page_erase((uint16_t)(void*)address);
-
+ // If we are in RWW section, immediately start page erase
+ if (address < NRWWSTART) __boot_page_erase_short((uint16_t)(void*)address);
+
// While that is going on, read in page contents
bufPtr = buff;
do *bufPtr++ = getch();
while (--length);
+ // If we are in NRWW section, page erase has to be delayed until now.
+ // Todo: Take RAMPZ into account
+ if (address >= NRWWSTART) __boot_page_erase_short((uint16_t)(void*)address);
+
// Read command terminator, start reply
verifySpace();
@@ -310,10 +349,10 @@ int main(void) {
// Move RESET vector to WDT vector
uint16_t vect = buff[0] | (buff[1]<<8);
rstVect = vect;
- wdtVect = buff[10] | (buff[11]<<8);
+ wdtVect = buff[8] | (buff[9]<<8);
vect -= 4; // Instruction is a relative jump (rjmp), so recalculate.
- buff[10] = vect & 0xff;
- buff[11] = vect >> 8;
+ buff[8] = vect & 0xff;
+ buff[9] = vect >> 8;
// Add jump to bootloader at RESET vector
buff[0] = 0x7f;
@@ -329,12 +368,12 @@ int main(void) {
uint16_t a;
a = *bufPtr++;
a |= (*bufPtr++) << 8;
- boot_page_fill((uint16_t)(void*)addrPtr,a);
+ __boot_page_fill_short((uint16_t)(void*)addrPtr,a);
addrPtr += 2;
} while (--ch);
// Write from programming buffer
- boot_page_write((uint16_t)(void*)address);
+ __boot_page_write_short((uint16_t)(void*)address);
boot_spm_busy_wait();
#if defined(RWWSRE)
@@ -353,16 +392,28 @@ int main(void) {
// Undo vector patch in bottom page so verify passes
if (address == 0) ch=rstVect & 0xff;
else if (address == 1) ch=rstVect >> 8;
- else if (address == 10) ch=wdtVect & 0xff;
- else if (address == 11) ch=wdtVect >> 8;
+ else if (address == 8) ch=wdtVect & 0xff;
+ else if (address == 9) ch=wdtVect >> 8;
else ch = pgm_read_byte_near(address);
address++;
putch(ch);
} while (--length);
#else
+#ifdef __AVR_ATmega1280__
+// do putch(pgm_read_byte_near(address++));
+// while (--length);
+ do {
+ uint8_t result;
+ __asm__ ("elpm %0,Z\n":"=r"(result):"z"(address));
+ putch(result);
+ address++;
+ }
+ while (--length);
+#else
do putch(pgm_read_byte_near(address++));
while (--length);
#endif
+#endif
}
/* Get device signature bytes */
@@ -422,8 +473,12 @@ uint8_t getch(void) {
watchdogReset();
#ifdef LED_DATA_FLASH
+#ifdef __AVR_ATmega8__
+ LED_PORT ^= _BV(LED);
+#else
LED_PIN |= _BV(LED);
#endif
+#endif
#ifdef SOFT_UART
__asm__ __volatile__ (
@@ -455,14 +510,19 @@ uint8_t getch(void) {
#endif
#ifdef LED_DATA_FLASH
+#ifdef __AVR_ATmega8__
+ LED_PORT ^= _BV(LED);
+#else
LED_PIN |= _BV(LED);
#endif
+#endif
return ch;
}
#ifdef SOFT_UART
-//#define UART_B_VALUE (((F_CPU/BAUD_RATE)-23)/6)
+// AVR350 equation: #define UART_B_VALUE (((F_CPU/BAUD_RATE)-23)/6)
+// Adding 3 to numerator simulates nearest rounding for more accurate baud rates
#define UART_B_VALUE (((F_CPU/BAUD_RATE)-20)/6)
#if UART_B_VALUE > 255
#error Baud rate too slow for soft UART
@@ -495,7 +555,11 @@ void flash_led(uint8_t count) {
TCNT1 = -(F_CPU/(1024*16));
TIFR1 = _BV(TOV1);
while(!(TIFR1 & _BV(TOV1)));
+#ifdef __AVR_ATmega8__
+ LED_PORT ^= _BV(LED);
+#else
LED_PIN |= _BV(LED);
+#endif
watchdogReset();
} while (--count);
}
@@ -524,7 +588,7 @@ void appStart() {
__asm__ __volatile__ (
#ifdef VIRTUAL_BOOT_PARTITION
// Jump to WDT vector
- "ldi r30,5\n"
+ "ldi r30,4\n"
"clr r31\n"
#else
// Jump to RST vector
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-11-22 17:38:55 +0000