aboutsummaryrefslogtreecommitdiff
path: root/bootloaders/diskloader/src
diff options
context:
space:
mode:
Diffstat (limited to 'bootloaders/diskloader/src')
-rw-r--r--bootloaders/diskloader/src/DiskLoader.cpp251
-rw-r--r--bootloaders/diskloader/src/Platform.h56
-rw-r--r--bootloaders/diskloader/src/SCSI.cpp213
-rw-r--r--bootloaders/diskloader/src/ThinFAT.cpp130
-rw-r--r--bootloaders/diskloader/src/USBCore.cpp526
-rw-r--r--bootloaders/diskloader/src/USBCore.h261
-rw-r--r--bootloaders/diskloader/src/USBDesc.cpp88
-rw-r--r--bootloaders/diskloader/src/USBDesc.h81
8 files changed, 1606 insertions, 0 deletions
diff --git a/bootloaders/diskloader/src/DiskLoader.cpp b/bootloaders/diskloader/src/DiskLoader.cpp
new file mode 100644
index 0000000..9ecbc4b
--- /dev/null
+++ b/bootloaders/diskloader/src/DiskLoader.cpp
@@ -0,0 +1,251 @@
+
+
+#include "Platform.h"
+
+// This bootloader creates a composite Serial/Mass storage device
+//
+// The serial interface supports a STK500v1 protocol that is very similar to optiboot
+// The mass storage interface emulates a disk image that is used to read or write firmware.bin files
+// Delete firmware.bin and copy a new binary (not .hex) file to flash the firmware i.e:
+//
+// cp firmware.bin f:/. -f
+//
+// Ejecting the disk will run the firmware
+//
+// The bootloader will timeout and start the firmware after a few hundred milliseconds
+// if a usb connection is not detected.
+//
+// The tweakier code is to keep the bootloader below 2k (no interrupt table, for example)
+
+extern "C"
+void entrypoint(void) __attribute__ ((naked)) __attribute__ ((section (".vectors")));
+void entrypoint(void)
+{
+ asm volatile (
+ "eor r1, r1\n" // Zero register
+ "out 0x3F, r1\n" // SREG
+ "ldi r28, 0xFF\n"
+ "ldi r29, 0x0A\n"
+ "out 0x3E, r29\n" // SPH
+ "out 0x3D, r28\n" // SPL
+ "rjmp main" // Stack is all set up, start the main code
+ ::);
+}
+
+u8 _flashbuf[128];
+u8 _inSync;
+u8 _ok;
+extern volatile u8 _ejected;
+extern volatile u16 _timeout;
+
+void Program(u8 ep, u16 page, u8 count)
+{
+ u8 write = page < 30*1024; // Don't write over firmware please
+ if (write)
+ boot_page_erase(page);
+
+ Recv(ep,_flashbuf,count); // Read while page is erasing
+
+ if (!write)
+ return;
+
+ boot_spm_busy_wait(); // Wait until the memory is erased.
+
+ count >>= 1;
+ u16* p = (u16*)page;
+ u16* b = (u16*)_flashbuf;
+ for (u8 i = 0; i < count; i++)
+ boot_page_fill(p++, b[i]);
+
+ boot_page_write(page);
+ boot_spm_busy_wait();
+ boot_rww_enable ();
+}
+
+
+int USBGetChar();
+#define getch USBGetChar
+
+#define HW_VER 0x02
+#define SW_MAJOR 0x01
+#define SW_MINOR 0x10
+
+#define STK_OK 0x10
+#define STK_INSYNC 0x14 // ' '
+#define CRC_EOP 0x20 // 'SPACE'
+#define STK_GET_SYNC 0x30 // '0'
+
+#define STK_GET_PARAMETER 0x41 // 'A'
+#define STK_SET_DEVICE 0x42 // 'B'
+#define STK_SET_DEVICE_EXT 0x45 // 'E'
+#define STK_LOAD_ADDRESS 0x55 // 'U'
+#define STK_UNIVERSAL 0x56 // 'V'
+#define STK_PROG_PAGE 0x64 // 'd'
+#define STK_READ_PAGE 0x74 // 't'
+#define STK_READ_SIGN 0x75 // 'u'
+
+extern const u8 _readSize[] PROGMEM;
+const u8 _readSize[] =
+{
+ STK_GET_PARAMETER, 1,
+ STK_SET_DEVICE, 20,
+ STK_SET_DEVICE_EXT, 5,
+ STK_UNIVERSAL, 4,
+ STK_LOAD_ADDRESS, 2,
+ STK_PROG_PAGE, 3,
+ STK_READ_PAGE, 3,
+ 0,0
+};
+
+extern const u8 _consts[] PROGMEM;
+const u8 _consts[] =
+{
+ SIGNATURE_0,
+ SIGNATURE_1,
+ SIGNATURE_2,
+ HW_VER, // Hardware version
+ SW_MAJOR, // Software major version
+ SW_MINOR, // Software minor version
+ 0x03, // Unknown but seems to be required by avr studio 3.56
+ 0x00, //
+};
+
+
+void USBInit(void);
+extern u8 _sector3[512];
+
+int main(void) __attribute__ ((naked));
+
+// STK500v1 main loop, very similar to optiboot in protocol and implementation
+int main()
+{
+ TXLED0;
+ RXLED0;
+ LED0;
+ BOARD_INIT();
+ USBInit();
+
+#ifdef WRITABLE_DIRECTORY
+ _sector3[0] = 0;
+#endif
+
+ _inSync = STK_INSYNC;
+ _ok = STK_OK;
+#ifndef MSC_ENABLED
+ if (pgm_read_word(0) != -1)
+ _ejected = 1;
+#endif
+ for(;;)
+ {
+ u8* packet = _flashbuf;
+ u16 address = 0;
+ for (;;)
+ {
+ u8 cmd = getch();
+
+ // Read packet contents
+ u8 len;
+ const u8* rs = _readSize;
+ for(;;)
+ {
+ u8 c = pgm_read_byte(rs++);
+ len = pgm_read_byte(rs++);
+ if (c == cmd || c == 0)
+ break;
+ }
+#ifndef MSC_ENABLED
+ _timeout = 0;
+#endif
+ // Read params
+ Recv(CDC_RX,packet,len);
+
+ // Send a response
+ u8 send = 0;
+ const u8* pgm = _consts+7; // 0
+ if (STK_GET_PARAMETER == cmd)
+ {
+ u8 i = packet[0] - 0x80;
+ if (i > 2)
+ i = (i == 0x18) ? 3 : 4; // 0x80:HW_VER,0x81:SW_MAJOR,0x82:SW_MINOR,0x18:3 or 0
+ pgm = _consts + i + 3;
+ send = 1;
+ }
+
+ else if (STK_UNIVERSAL == cmd)
+ {
+ if (packet[0] == 0x30)
+ pgm = _consts + packet[2]; // read signature
+ send = 1;
+ }
+
+ // Read signature bytes
+ else if (STK_READ_SIGN == cmd)
+ {
+ pgm = _consts;
+ send = 3;
+ }
+
+ else if (STK_LOAD_ADDRESS == cmd)
+ {
+ address = *((u16*)packet); // word addresses
+ address += address;
+ }
+
+ else if (STK_PROG_PAGE == cmd)
+ {
+ Program(CDC_RX,address,packet[1]);
+ }
+
+ else if (STK_READ_PAGE == cmd)
+ {
+ send = packet[1];
+ pgm = (const u8*)address;
+ address += send; // not sure of this is required
+ }
+
+ // Check sync
+ if (getch() != ' ')
+ break;
+ Transfer(CDC_TX,&_inSync,1);
+
+ // Send result
+ if (send)
+ Transfer(CDC_TX|TRANSFER_PGM,pgm,send); // All from pgm memory
+
+ // Send ok
+ Transfer(CDC_TX|TRANSFER_RELEASE,&_ok,1);
+
+ if (cmd == 'Q')
+ break;
+ }
+ _timeout = 1; // signal to exit the bootloader
+ _ejected = 1;
+ }
+}
+
+// Nice breathing LED indicates we are in the firmware
+u16 _pulse;
+void LEDPulse()
+{
+ _pulse++;
+ u8 p = _pulse >> 8;
+ if (p > 127)
+ p = 255-p;
+ p += p;
+ if (((u8)_pulse) > p)
+ LED0;
+ else
+ LED1;
+}
+
+void Reboot()
+{
+ /* TODO - ZE - this should probably be a WDT reset instead, right? */
+ UDCON = 1; // Detatch USB
+ UDIEN = 0;
+ asm volatile ( // Reset vector to run firmware
+ "clr r30\n"
+ "clr r31\n"
+ "ijmp\n"
+ ::);
+}
diff --git a/bootloaders/diskloader/src/Platform.h b/bootloaders/diskloader/src/Platform.h
new file mode 100644
index 0000000..004933e
--- /dev/null
+++ b/bootloaders/diskloader/src/Platform.h
@@ -0,0 +1,56 @@
+
+#include <inttypes.h>
+#include <avr/io.h>
+#include <avr/pgmspace.h>
+#include <avr/boot.h>
+#include <util/delay.h>
+#include <avr/interrupt.h>
+
+#include <stdio.h>
+#include <stdlib.h>
+#include <string.h>
+
+typedef unsigned char u8;
+typedef unsigned short u16;
+typedef unsigned long u32;
+
+//#define MICROTOUCH
+
+//#define WRITABLE_DIRECTORY // undef saved 56 + 512 RAM
+
+#define FAT_DISK_LABEL 'b','o','o','t','l','o','a','d','e','r',' ' // 11 chars (undef saves 12)
+#define FAT_FILE_NAME 'F','I','R','M','W','A','R','E','B','I','N' // 11 chars
+#define MSC_DISK_SERIAL '0','0','0','0','0','0','0','0','1','7','0','1' // 12 chars
+
+
+#define CPU_PRESCALE(n) (CLKPR = 0x80, CLKPR = (n))
+#define DISABLE_JTAG() MCUCR = (1 << JTD) | (1 << IVCE) | (0 << PUD); MCUCR = (1 << JTD) | (0 << IVSEL) | (0 << IVCE) | (0 << PUD);
+
+#define USB_VID 0x2341 // arduino LLC vid
+#define USB_PID 0x0020 // educated guess
+
+#define FAT_OEM_NAME 'l','e','o','n','a','r','d','o' // 8 chars
+#define BOARD_INIT() DDRC |= (1<<7); DDRB |= (1<<0); DDRE |= (1<<6); CPU_PRESCALE(0); DISABLE_JTAG();
+#define LED0 PORTC &= ~(1<<7)
+#define LED1 PORTC |= (1<<7)
+#define TXLED0 PORTE |= (1<<6)
+#define TXLED1 PORTE &= ~(1<<6)
+#define RXLED0 PORTB |= (1<<0)
+#define RXLED1 PORTB &= ~(1<<0)
+
+#define TRANSFER_PGM 0x80
+#define TRANSFER_RELEASE 0x40
+#define TRANSFER_ZERO 0x20
+
+void Transfer(u8 ep, const u8* data, int len);
+void Recv(u8 ep, u8* dst, u8 len);
+void Program(u8 ep, u16 page, u8 count);
+
+#define CDC_ENABLED
+//#define MSC_ENABLED
+//#define MSC_NO_MEDIA // MSC is enabled but not media inserted
+
+#include "USBCore.h"
+#include "USBDesc.h"
+
+
diff --git a/bootloaders/diskloader/src/SCSI.cpp b/bootloaders/diskloader/src/SCSI.cpp
new file mode 100644
index 0000000..dbbf9cf
--- /dev/null
+++ b/bootloaders/diskloader/src/SCSI.cpp
@@ -0,0 +1,213 @@
+
+
+/* Copyright (c) 2010, Peter Barrett
+**
+** Permission to use, copy, modify, and/or distribute this software for
+** any purpose with or without fee is hereby granted, provided that the
+** above copyright notice and this permission notice appear in all copies.
+**
+** THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
+** WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
+** WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR
+** BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES
+** OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
+** WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION,
+** ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS
+** SOFTWARE.
+*/
+
+#include "Platform.h"
+
+#ifdef MSC_ENABLED
+
+// SCSI Commands
+#define TEST_UNIT_READY 0x00
+#define REQUEST_SENSE 0x03
+#define FORMAT_UNIT 0x04
+#define INQUIRY 0x12
+#define MODE_SENSE 0x1A
+#define START_STOP_UNIT 0x1B
+#define MEDIA_REMOVAL 0x1E
+#define READ_FORMAT_CAPACITIES 0x23
+#define READ_CAPACITY 0x25
+#define READ10 0x28
+#define WRITE10 0x2A
+#define VERIFY10 0x2F
+
+
+// In FakeFAT
+void SendSector(u8 b);
+void RecvSector(u8 b);
+
+// In USBCore
+u8 RecvPacket(u8 ep, u8* dst, u8 len);
+u8 SendPacket(u8 ep, const u8* src, u8 len);
+void Reboot();
+
+#define MSC_TX MSC_ENDPOINT_IN
+#define MSC_RX MSC_ENDPOINT_OUT
+
+extern const u8 P_Inquiry[36] PROGMEM;
+extern const u8 P_RequestSense[18] PROGMEM;
+extern const u8 P_ReadCapacity[8-3] PROGMEM;
+extern const u8 P_ModeSense[4] PROGMEM;
+
+typedef struct
+{
+ u8 signature[4];
+ u8 tag[4];
+ u32 transferLength;
+ u8 flags;
+ u8 lun;
+ u8 cblength;
+ u8 cb[16];
+} CBW;
+
+const u8 P_Inquiry[36] =
+{
+ 0x00, // Direct Access Device
+ 0x80, // Removable Medium
+ 0x00, // Version
+ 0x01,
+
+ 36-4, // Additional Length
+ 0x80, // Storage Controller Component
+ 0x00,
+ 0x00,
+
+ 'r','o','s','s','u','m','u','r', // Vendor
+
+ 'm','i','c','r','o','t','o','u', // Product
+ 'c','h',' ',' ',' ',' ',' ',' ',
+
+ '2','.','4',' ' // Revision
+};
+
+const u8 P_RequestSense[18] =
+{
+ 0x70, // Response Code
+ 0x00,
+// 0x02, // Sense Key
+ 0x00,
+ 0x00,
+
+ 0x00,
+ 0x00,
+ 0x00,
+ 0x0A, // Additional Length
+
+ 0x00,
+ 0x00,
+ 0x00,
+ 0x00,
+
+ 0x30, // ASC
+ 0x01, // ASCQ
+
+ 0x00,
+ 0x00,
+ 0x00,
+ 0x00
+};
+
+// Save 3 bytes if merging
+const u8 P_ReadCapacity[8-3] =
+{
+// 0x00,
+// 0x00,
+// 0x00, // Steal 3 zero bytes from end of P_RequestSense
+ 64+4, // block count 64 + 4
+ 0x00,
+ 0x00,
+ 0x02, // block size = 512
+ 0x00
+};
+
+const u8 P_ModeSense[4] =
+{
+ 0x03,
+ 0x00,
+ 0x00,
+ 0x00
+};
+
+extern volatile u8 _ejected;
+
+void SCSI(CBW& cbw)
+{
+ const u8* pgm = 0;
+ u8 status = 0;
+ u8 blen = 0;
+
+ u8 cmd = cbw.cb[0];
+ if (START_STOP_UNIT == cmd)
+ {
+ _ejected = 1; // Stopped; going away
+ }
+ else if (TEST_UNIT_READY == cmd || MEDIA_REMOVAL == cmd)
+ {
+#ifdef MSC_NO_MEDIA
+ status = 1;
+#else
+ status = _ejected;
+#endif
+ }
+ else if (REQUEST_SENSE == cmd)
+ {
+ pgm = P_RequestSense;
+ blen = sizeof(P_RequestSense);
+ }
+ else if (INQUIRY == cmd)
+ {
+ pgm = P_Inquiry;
+ blen = sizeof(P_Inquiry);
+ }
+ else if (WRITE10 == cmd || READ10 == cmd)
+ {
+ // Write 10 byte form
+ // Read 10 byte form
+ {
+ u8 lba = cbw.cb[5];
+ u8 count = cbw.cb[8];
+ u8 read = READ10 == cbw.cb[0];
+ while (count--)
+ {
+ if (read)
+ SendSector(lba);
+ else
+ RecvSector(lba);
+ lba++;
+ cbw.transferLength -= 512; // 24 bytes
+ }
+ }
+ }
+ else if (MODE_SENSE == cmd)
+ {
+ pgm = P_ModeSense;
+ blen = 4;
+ }
+ else
+ {
+ pgm = P_ReadCapacity-3;
+ blen = 8;
+ if (READ_CAPACITY != cmd)
+ status = 1; // Faking a data phase for unknown commands
+ }
+
+ if (pgm)
+ Transfer(MSC_TX | TRANSFER_PGM | TRANSFER_RELEASE,pgm,blen);
+
+ cbw.flags = status;
+ cbw.transferLength -= blen;
+ cbw.signature[3] = 'S';
+ Transfer(MSC_TX | TRANSFER_RELEASE,(u8*)&cbw,13);
+}
+
+CBW cbw; // 38 byte savings by making this global
+void SCSITask()
+{
+ Recv(MSC_RX,(u8*)&cbw,sizeof(CBW));
+ SCSI(cbw);
+}
+
+#endif \ No newline at end of file
diff --git a/bootloaders/diskloader/src/ThinFAT.cpp b/bootloaders/diskloader/src/ThinFAT.cpp
new file mode 100644
index 0000000..c238741
--- /dev/null
+++ b/bootloaders/diskloader/src/ThinFAT.cpp
@@ -0,0 +1,130 @@
+
+
+/* Copyright (c) 2011, Peter Barrett
+**
+** Permission to use, copy, modify, and/or distribute this software for
+** any purpose with or without fee is hereby granted, provided that the
+** above copyright notice and this permission notice appear in all copies.
+**
+** THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
+** WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
+** WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR
+** BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES
+** OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
+** WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION,
+** ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS
+** SOFTWARE.
+*/
+
+#include "Platform.h"
+
+#ifdef MSC_ENABLED
+
+extern const u8 Sector_0[] PROGMEM;
+extern const u8 Sector_1[] PROGMEM;
+extern const u8 Sector_2[] PROGMEM;
+extern const u8 Sector_3[] PROGMEM;
+extern const u8 Sector_Size[] PROGMEM;
+
+
+const u8 Sector_0[27] =
+{
+ 0xEB,0x3C,0x90,
+ FAT_OEM_NAME,
+ 0x00,0x02, // Bytes per sector 512
+ 0x40, // Sectors per Cluster 32k per cluster
+ 0x01,0x00, // Reserved sectors
+ 0x02, // FATSs
+ 0x10,0x00, // root entries
+ 4+64,0x00, // number of sectors: 30k file
+ 0xF8, // Media type fixed
+ 0x01,0x00, // Sectors per FAT
+ 0x01,0x00, // Sectors per head
+ 0x01,//0x00, // Heads per cylinder
+ //0x00,0x00,0x00,0x00, // Hidden
+ //0x00,0x00,0x00,0x00, // long number of sectors
+ //0x00,0x00, // Ext flags
+ // 38 bytes
+};
+
+// FAT12 clusters for 32k file
+const u8 Sector_1[] =
+{
+#if 0
+ 0xF8,0xFF,0xFF,
+ 0xFF,0x0F//,0x00
+#endif
+};
+
+const u8 Sector_2[] =
+{
+};
+
+const u8 Sector_3[] =
+{
+#if 0
+ FAT_FILE_NAME, 0x00,0x00,0x00,0x00,0x00, // Uppercase name please
+ 0x43,0x3E,0x43,0x3E,0x00,0x00,0xAB,0x8C,0x40,0x3E,0x02,0x00,0x00,0x80,//0x00,0x00
+ // 0x00,0x00,
+#endif
+
+#ifdef FAT_DISK_LABEL
+ FAT_DISK_LABEL,0x28
+#endif
+};
+
+#if 0
+const u8 Sector_Size[] =
+{
+ 0,
+ sizeof(Sector_0),
+ sizeof(Sector_0) + sizeof(Sector_1),
+ sizeof(Sector_0) + sizeof(Sector_1) + sizeof(Sector_2),
+ sizeof(Sector_0) + sizeof(Sector_1) + sizeof(Sector_2) + sizeof(Sector_3)
+};
+#endif
+
+const u8* LBAToROM(u8 b)
+{
+ b -= 4;
+ return (const u8*)(b << 9);
+}
+
+void SendSector(u8 b)
+{
+ if (b == 0)
+ {
+ u8 n = sizeof(Sector_0);
+ Transfer(MSC_TX | TRANSFER_PGM,Sector_0,n);
+ Transfer(MSC_TX | TRANSFER_ZERO,0,512-n);
+ return;
+ }
+
+ if ((b < 4) || (b >= 64))
+ {
+ Transfer(MSC_TX | TRANSFER_ZERO,0,512);
+ return;
+ }
+
+ // Copy body of file from ROM
+ Transfer(MSC_TX | TRANSFER_PGM,LBAToROM(b),512);
+}
+
+#define GENERATE_INVALID_ROM_ADDRESS 60
+
+void RecvSector(u8 lba)
+{
+ if ((lba < 4) || (lba >= 64))
+ lba = GENERATE_INVALID_ROM_ADDRESS; // Only care about the first 30k
+
+ // Write sectors to flash
+ u16 addr = (u16)LBAToROM(lba); // may generate out of range addresses, Program will fix
+ u8 i = 4; // 4x128 is a sector
+ while (i--)
+ {
+ Program(MSC_RX,addr,128);
+ addr += 128;
+ }
+}
+
+#endif \ No newline at end of file
diff --git a/bootloaders/diskloader/src/USBCore.cpp b/bootloaders/diskloader/src/USBCore.cpp
new file mode 100644
index 0000000..8b071a1
--- /dev/null
+++ b/bootloaders/diskloader/src/USBCore.cpp
@@ -0,0 +1,526 @@
+
+
+/* Copyright (c) 2010, Peter Barrett
+**
+** Permission to use, copy, modify, and/or distribute this software for
+** any purpose with or without fee is hereby granted, provided that the
+** above copyright notice and this permission notice appear in all copies.
+**
+** THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
+** WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
+** WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR
+** BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES
+** OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
+** WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION,
+** ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS
+** SOFTWARE.
+*/
+
+#include "Platform.h"
+
+#define MSC_TX MSC_ENDPOINT_IN
+#define MSC_RX MSC_ENDPOINT_OUT
+#define CDC_TX CDC_ENDPOINT_IN
+#define CDC_RX CDC_ENDPOINT_OUT
+
+#define EP_TYPE_CONTROL 0x00
+#define EP_TYPE_BULK_IN 0x81
+#define EP_TYPE_BULK_OUT 0x80
+#define EP_TYPE_INTERRUPT_IN 0xC1
+#define EP_TYPE_INTERRUPT_OUT 0xC0
+#define EP_TYPE_ISOCHRONOUS_IN 0x41
+#define EP_TYPE_ISOCHRONOUS_OUT 0x40
+
+void Reboot();
+
+//==================================================================
+//==================================================================
+
+typedef struct
+{
+ u32 dwDTERate;
+ u8 bCharFormat;
+ u8 bParityType;
+ u8 bDataBits;
+ u8 lineState;
+} LineInfo;
+
+static volatile LineInfo _usbLineInfo = { 57600, 0x00, 0x00, 0x00, 0x00 };
+
+//==================================================================
+//==================================================================
+
+// 4 bytes of RAM
+volatile u8 _usbConfiguration;
+volatile u8 _ejected;
+volatile u16 _timeout;
+
+static inline void WaitIN(void)
+{
+ while (!(UEINTX & (1<<TXINI)));
+}
+
+static inline void ClearIN(void)
+{
+ UEINTX = ~(1<<TXINI);
+}
+
+static inline void WaitOUT(void)
+{
+ while (!(UEINTX & (1<<RXOUTI)))
+ ;
+}
+
+static inline u8 WaitForINOrOUT()
+{
+ while (!(UEINTX & ((1<<TXINI)|(1<<RXOUTI))))
+ ;
+ return (UEINTX & (1<<RXOUTI)) == 0;
+}
+
+static inline void ClearOUT(void)
+{
+ UEINTX = ~(1<<RXOUTI);
+}
+
+static
+void Send(volatile const u8* data, u8 count)
+{
+ TXLED1; // light the TX LED
+ while (count--)
+ UEDATX = *data++;
+}
+
+void Recv(volatile u8* data, u8 count)
+{
+ RXLED1; // light the RX LED
+ while (count--)
+ *data++ = UEDATX;
+}
+
+static inline u8 Recv8()
+{
+ RXLED1; // light the RX LED
+ return UEDATX;
+}
+
+static inline void Send8(u8 d)
+{
+ TXLED1; // light the TX LED
+ UEDATX = d;
+}
+
+static inline void SetEP(u8 ep)
+{
+ UENUM = ep;
+}
+
+static inline u8 FifoByteCount()
+{
+ return UEBCLX;
+}
+
+static inline u8 ReceivedSetupInt()
+{
+ return UEINTX & (1<<RXSTPI);
+}
+
+static inline void ClearSetupInt()
+{
+ UEINTX = ~((1<<RXSTPI) | (1<<RXOUTI) | (1<<TXINI));
+}
+
+static inline void Stall()
+{
+ UECONX = (1<<STALLRQ) | (1<<EPEN);
+}
+
+static inline u8 ReadWriteAllowed()
+{
+ return UEINTX & (1<<RWAL);
+}
+
+static inline u8 Stalled()
+{
+ return UEINTX & (1<<STALLEDI);
+}
+
+static inline u8 FifoFree()
+{
+ return UEINTX & (1<<FIFOCON);
+}
+
+static inline void ReleaseRX()
+{
+ UEINTX = 0x6B; // FIFOCON=0 NAKINI=1 RWAL=1 NAKOUTI=0 RXSTPI=1 RXOUTI=0 STALLEDI=1 TXINI=1
+}
+
+static inline void ReleaseTX()
+{
+ UEINTX = 0x3A; // FIFOCON=0 NAKINI=0 RWAL=1 NAKOUTI=1 RXSTPI=1 RXOUTI=0 STALLEDI=1 TXINI=0
+}
+
+static inline u8 FrameNumber()
+{
+ return UDFNUML;
+}
+
+//==================================================================
+//==================================================================
+
+#define EP_SINGLE_64 0x32 // EP0
+#define EP_DOUBLE_64 0x36 // Other endpoints
+
+static void InitEP(u8 index, u8 type, u8 size)
+{
+ UENUM = index;
+ UECONX = 1;
+ UECFG0X = type;
+ UECFG1X = size;
+}
+
+// API
+void USBInit(void)
+{
+ _timeout = 0;
+ _usbConfiguration = 0;
+ _ejected = 0;
+
+ UHWCON = 0x01; // power internal reg (don't need this?)
+ USBCON = (1<<USBE)|(1<<FRZCLK); // clock frozen, usb enabled
+ PLLCSR = 0x12; // Need 16 MHz xtal
+ while (!(PLLCSR & (1<<PLOCK))) // wait for lock pll
+ ;
+ USBCON = ((1<<USBE)|(1<<OTGPADE)); // start USB clock
+ UDCON = 0; // enable attach resistor
+}
+
+u8 USBGetConfiguration(void)
+{
+ return _usbConfiguration;
+}
+
+u8 HasData(u8 ep)
+{
+ SetEP(ep);
+ return ReadWriteAllowed(); // count in fifo
+}
+
+int USBGetChar();
+void Recv(u8 ep, u8* dst, u8 len)
+{
+ SetEP(ep);
+ while (len--)
+ {
+ while (!ReadWriteAllowed())
+ ;
+ *dst++ = Recv8();
+ if (!ReadWriteAllowed()) // release empty buffer
+ ReleaseRX();
+ }
+}
+
+// Transmit a packet to endpoint
+void Transfer(u8 ep, const u8* data, int len)
+{
+ u8 zero = ep & TRANSFER_ZERO;
+ SetEP(ep & 7);
+ while (len--)
+ {
+ while (!ReadWriteAllowed())
+ ; // TODO Check for STALL etc
+
+ u8 d = (ep & TRANSFER_PGM) ? pgm_read_byte(data) : data[0];
+ data++;
+ if (zero)
+ d = 0;
+ Send8(d);
+
+ if (!ReadWriteAllowed())
+ ReleaseTX();
+ }
+ if (ep & TRANSFER_RELEASE)
+ ReleaseTX();
+}
+
+extern const u8 _initEndpoints[] PROGMEM;
+const u8 _initEndpoints[] =
+{
+ 0,
+
+#ifdef CDC_ENABLED
+ EP_TYPE_INTERRUPT_IN, // CDC_ENDPOINT_ACM
+ EP_TYPE_BULK_OUT, // CDC_ENDPOINT_OUT
+ EP_TYPE_BULK_IN, // CDC_ENDPOINT_IN
+#endif
+
+ EP_TYPE_INTERRUPT_IN, // HID_ENDPOINT_INT
+
+#ifdef MSC_ENABLED
+ EP_TYPE_BULK_OUT, // MSC_ENDPOINT_OUT
+ EP_TYPE_BULK_IN // MSC_ENDPOINT_IN
+#endif
+};
+
+static void InitEndpoints()
+{
+ for (u8 i = 1; i < sizeof(_initEndpoints); i++)
+ {
+ UENUM = i;
+ UECONX = 1;
+ UECFG0X = pgm_read_byte(_initEndpoints+i);
+ UECFG1X = EP_DOUBLE_64;
+ }
+ UERST = 0x7E; // And reset them
+ UERST = 0;
+}
+
+typedef struct
+{
+ u8 bmRequestType;
+ u8 bRequest;
+ u8 wValueL;
+ u8 wValueH;
+ u16 wIndex;
+ u16 wLength;
+} Setup;
+Setup _setup;
+
+//bool USBHook(Setup& setup)
+bool USBHook()
+{
+ Setup& setup = _setup;
+ u8 r = setup.bRequest;
+
+ // CDC Requests
+ if (CDC_GET_LINE_CODING == r)
+ {
+ Send((const volatile u8*)&_usbLineInfo,7);
+ }
+
+ else if (CDC_SET_LINE_CODING == r)
+ {
+ WaitOUT();
+ Recv((volatile u8*)&_usbLineInfo,7);
+ ClearOUT();
+ }
+
+ else if (CDC_SET_CONTROL_LINE_STATE == r)
+ {
+ _usbLineInfo.lineState = setup.wValueL;
+ }
+
+#ifdef MSC_ENABLED
+ // MSC Requests
+ else if (MSC_GET_MAX_LUN == r)
+ {
+ Send8(0);
+ }
+ else if (MSC_RESET == r)
+ {
+ // MSC_Reset();
+ } else
+ return false; // unhandled
+#endif
+
+ return true;
+}
+
+extern const u8 _rawHID[] PROGMEM;
+#define LSB(_x) ((_x) & 0xFF)
+#define MSB(_x) ((_x) >> 8)
+
+#define RAWHID_USAGE_PAGE 0xFFC0
+#define RAWHID_USAGE 0x0C00
+#define RAWHID_TX_SIZE 64
+#define RAWHID_RX_SIZE 64
+
+const u8 _rawHID[] =
+{
+ // RAW HID
+ 0x06, LSB(RAWHID_USAGE_PAGE), MSB(RAWHID_USAGE_PAGE), // 30
+ 0x0A, LSB(RAWHID_USAGE), MSB(RAWHID_USAGE),
+
+ 0xA1, 0x01, // Collection 0x01
+ 0x85, 0x03, // REPORT_ID (3)
+ 0x75, 0x08, // report size = 8 bits
+ 0x15, 0x00, // logical minimum = 0
+ 0x26, 0xFF, 0x00, // logical maximum = 255
+
+ 0x95, 64, // report count TX
+ 0x09, 0x01, // usage
+ 0x81, 0x02, // Input (array)
+
+ 0x95, 64, // report count RX
+ 0x09, 0x02, // usage
+ 0x91, 0x02, // Output (array)
+ 0xC0 // end collection
+};
+
+u8 _cdcComposite = 0;
+
+bool SendDescriptor()
+{
+ Setup& setup = _setup;
+ u8 desc_length = 0;
+ const u8* desc_addr = 0;
+
+ u8 t = setup.wValueH;
+ if (0x22 == t)
+ {
+ desc_addr = _rawHID;
+ desc_length = sizeof(desc_length);
+ } else if (USB_DEVICE_DESCRIPTOR_TYPE == t)
+ {
+ if (setup.wLength == 8)
+ _cdcComposite = 1;
+ desc_addr = _cdcComposite ? (const u8*)&USB_DeviceDescriptorA : (const u8*)&USB_DeviceDescriptor;
+ }
+ else if (USB_CONFIGURATION_DESCRIPTOR_TYPE == t)
+ {
+ desc_addr = (const u8*)&USB_ConfigDescriptor;
+ desc_length = sizeof(USB_ConfigDescriptor);
+ }
+ else if (USB_STRING_DESCRIPTOR_TYPE == t)
+ {
+ if (setup.wValueL == 0)
+ desc_addr = (const u8*)&STRING_LANGUAGE;
+ else if (setup.wValueL == ISERIAL)
+ desc_addr = (const u8*)&STRING_SERIAL;
+ else
+ return false;
+ } else
+ return false;
+
+ if (desc_length == 0)
+ desc_length = pgm_read_byte(desc_addr);
+ if ((u8)setup.wLength < desc_length) // bit of a cheat limiting to 255 bytes TODO (saved 8 bytes)
+ desc_length = (u8)setup.wLength;
+
+ // Send descriptor
+ // EP0 is 64 bytes long
+ // RWAL and FIFOCON don't work on EP0
+ u8 n = 0;
+ do
+ {
+ if (!WaitForINOrOUT())
+ return false;
+ Send8(pgm_read_byte(&desc_addr[n++]));
+ u8 clr = n & 0x3F;
+ if (!clr)
+ ClearIN(); // Fifo is full, release this packet
+ } while (n < desc_length);
+ return true;
+}
+
+void USBSetupInterrupt()
+{
+ SetEP(0);
+ if (!ReceivedSetupInt())
+ return;
+
+ Setup& setup = _setup; // global saves ~30 bytes
+ Recv((u8*)&setup,8);
+ ClearSetupInt();
+
+ if (setup.bmRequestType & DEVICETOHOST)
+ WaitIN();
+ else
+ ClearIN();
+
+ bool ok = true;
+ u8 r = setup.bRequest;
+ if (SET_ADDRESS == r)
+ {
+ WaitIN();
+ UDADDR = setup.wValueL | (1<<ADDEN);
+ }
+ else if (SET_CONFIGURATION == r)
+ {
+ _usbConfiguration = setup.wValueL;
+ InitEndpoints();
+ }
+ else if (GET_CONFIGURATION == r)
+ {
+ Send8(_usbConfiguration);
+ }
+ else if (GET_STATUS == r)
+ {
+ Send8(0); // All good as far as I know
+ }
+ else if (GET_DESCRIPTOR == r)
+ {
+ ok = SendDescriptor();
+ }
+ else
+ {
+ ok = USBHook();
+ }
+
+ if (ok)
+ ClearIN();
+ else
+ Stall();
+}
+
+void USBGeneralInterrupt()
+{
+ u8 udint = UDINT;
+ UDINT = 0;
+
+ // End of Reset
+ if (udint & (1<<EORSTI))
+ {
+ InitEP(0,EP_TYPE_CONTROL,EP_SINGLE_64); // init ep0
+ _usbConfiguration = 0; // not configured yet
+ //UEIENX = 1 << RXSTPE;
+ }
+
+ // Start of Frame
+ if (udint & (1<<SOFI))
+ {
+ if (!_ejected)
+ _timeout = 0;
+ }
+}
+
+void SCSITask();
+
+void LEDPulse();
+int USBGetChar()
+{
+ for(;;)
+ {
+ USBSetupInterrupt();
+ USBGeneralInterrupt();
+
+#ifdef MSC_ENABLED
+ // Service disk
+ if (HasData(MSC_RX))
+ SCSITask();
+#endif
+ // Read a char
+ if (HasData(CDC_RX))
+ {
+ u8 c = Recv8();
+ if (!ReadWriteAllowed())
+ ReleaseRX();
+ return c;
+ } else {
+ u8 temp = 0;
+ for (temp=100; temp; temp--)
+ asm volatile("nop\n\t" "nop\n\t" "nop\n\t" "nop\n\t"::);
+ RXLED0; // we turn the RX and TX LEDs on in the relevant Send or Recv instruction
+ TXLED0; // we turn them off here after some time has passed to ensure a minimum on time.
+ }
+
+ if (!--_timeout) {
+ TXLED0; // switch off the RX and TX LEDs before starting the user sketch
+ RXLED0;
+ Reboot(); // USB not connected, run firmware
+ }
+
+ LEDPulse();
+ }
+ return -1;
+}
diff --git a/bootloaders/diskloader/src/USBCore.h b/bootloaders/diskloader/src/USBCore.h
new file mode 100644
index 0000000..a37b9f2
--- /dev/null
+++ b/bootloaders/diskloader/src/USBCore.h
@@ -0,0 +1,261 @@
+
+// Copyright (c) 2010, Peter Barrett
+/*
+** Permission to use, copy, modify, and/or distribute this software for
+** any purpose with or without fee is hereby granted, provided that the
+** above copyright notice and this permission notice appear in all copies.
+**
+** THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
+** WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
+** WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR
+** BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES
+** OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
+** WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION,
+** ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS
+** SOFTWARE.
+*/
+
+#ifndef __USBCORE_H__
+#define __USBCORE_H__
+
+#define GET_STATUS 0
+#define CLEAR_FEATURE 1
+#define SET_FEATURE 3
+#define SET_ADDRESS 5
+#define GET_DESCRIPTOR 6
+#define GET_CONFIGURATION 8
+#define SET_CONFIGURATION 9
+#define GET_INTERFACE 10
+#define SET_INTERFACE 11
+
+// bmRequestType
+#define HOSTTODEVICE 0x00
+#define DEVICETOHOST 0x80
+#define STANDARD 0x00
+#define CLASS 0x20
+#define VENDOR 0x40
+#define DEVICE 0x00
+#define INTERFACE 0x01
+#define ENDPOINT 0x02
+#define OTHER 0x03
+
+#define CDC_SET_LINE_CODING 0x20
+#define CDC_GET_LINE_CODING 0x21
+#define CDC_SET_CONTROL_LINE_STATE 0x22
+
+#define MSC_RESET 0xFF
+#define MSC_GET_MAX_LUN 0xFE
+
+
+// Descriptors
+
+#define USB_DEVICE_DESC_SIZE 18
+#define USB_CONFIGUARTION_DESC_SIZE 9
+#define USB_INTERFACE_DESC_SIZE 9
+#define USB_ENDPOINT_DESC_SIZE 7
+
+#define USB_DEVICE_DESCRIPTOR_TYPE 1
+#define USB_CONFIGURATION_DESCRIPTOR_TYPE 2
+#define USB_STRING_DESCRIPTOR_TYPE 3
+#define USB_INTERFACE_DESCRIPTOR_TYPE 4
+#define USB_ENDPOINT_DESCRIPTOR_TYPE 5
+
+#define USB_DEVICE_CLASS_COMMUNICATIONS 0x02
+#define USB_DEVICE_CLASS_HUMAN_INTERFACE 0x03
+#define USB_DEVICE_CLASS_STORAGE 0x08
+#define USB_DEVICE_CLASS_VENDOR_SPECIFIC 0xFF
+
+#define USB_CONFIG_POWERED_MASK 0x40
+#define USB_CONFIG_BUS_POWERED 0x80
+#define USB_CONFIG_SELF_POWERED 0xC0
+#define USB_CONFIG_REMOTE_WAKEUP 0x20
+
+// bMaxPower in Configuration Descriptor
+#define USB_CONFIG_POWER_MA(mA) ((mA)/2)
+
+// bEndpointAddress in Endpoint Descriptor
+#define USB_ENDPOINT_DIRECTION_MASK 0x80
+#define USB_ENDPOINT_OUT(addr) ((addr) | 0x00)
+#define USB_ENDPOINT_IN(addr) ((addr) | 0x80)
+
+#define USB_ENDPOINT_TYPE_MASK 0x03
+#define USB_ENDPOINT_TYPE_CONTROL 0x00
+#define USB_ENDPOINT_TYPE_ISOCHRONOUS 0x01
+#define USB_ENDPOINT_TYPE_BULK 0x02
+#define USB_ENDPOINT_TYPE_INTERRUPT 0x03
+
+#define TOBYTES(x) ((x) & 0xFF),(((x) >> 8) & 0xFF)
+
+#define CDC_V1_10 0x0110
+#define CDC_COMMUNICATION_INTERFACE_CLASS 0x02
+
+#define CDC_CALL_MANAGEMENT 0x01
+#define CDC_ABSTRACT_CONTROL_MODEL 0x02
+#define CDC_HEADER 0x00
+#define CDC_ABSTRACT_CONTROL_MANAGEMENT 0x02
+#define CDC_UNION 0x06
+#define CDC_CS_INTERFACE 0x24
+#define CDC_CS_ENDPOINT 0x25
+#define CDC_DATA_INTERFACE_CLASS 0x0A
+
+#define MSC_SUBCLASS_SCSI 0x06
+#define MSC_PROTOCOL_BULK_ONLY 0x50
+
+
+
+// Device
+typedef struct {
+ u8 len; // 18
+ u8 dtype; // 1 USB_DEVICE_DESCRIPTOR_TYPE
+ u16 usbVersion; // 0x200
+ u8 deviceClass;
+ u8 deviceSubClass;
+ u8 deviceProtocol;
+ u8 packetSize0; // Packet 0
+ u16 idVendor;
+ u16 idProduct;
+ u16 deviceVersion; // 0x100
+ u8 iManufacturer;
+ u8 iProduct;
+ u8 iSerialNumber;
+ u8 bNumConfigurations;
+} DeviceDescriptor;
+
+// Config
+typedef struct {
+ u8 len; // 9
+ u8 dtype; // 2
+ u16 clen; // total length
+ u8 numInterfaces;
+ u8 config;
+ u8 iconfig;
+ u8 attributes;
+ u8 maxPower;
+} ConfigDescriptor;
+
+// String
+
+// Interface
+typedef struct
+{
+ u8 len; // 9
+ u8 dtype; // 4
+ u8 number;
+ u8 alternate;
+ u8 numEndpoints;
+ u8 interfaceClass;
+ u8 interfaceSubClass;
+ u8 protocol;
+ u8 iInterface;
+} InterfaceDescriptor;
+
+// Endpoint
+typedef struct
+{
+ u8 len; // 7
+ u8 dtype; // 5
+ u8 addr;
+ u8 attr;
+ u16 packetSize;
+ u8 interval;
+} EndpointDescriptor;
+
+// Interface Association Descriptor
+// Used to bind 2 interfaces together in CDC compostite device
+typedef struct
+{
+ u8 len; // 8
+ u8 dtype; // 11
+ u8 firstInterface;
+ u8 interfaceCount;
+ u8 functionClass;
+ u8 funtionSubClass;
+ u8 functionProtocol;
+ u8 iInterface;
+} IADDescriptor;
+
+// CDC CS interface descriptor
+typedef struct
+{
+ u8 len; // 5
+ u8 dtype; // 0x24
+ u8 subtype;
+ u8 d0;
+ u8 d1;
+} CDCCSInterfaceDescriptor;
+
+typedef struct
+{
+ u8 len; // 4
+ u8 dtype; // 0x24
+ u8 subtype;
+ u8 d0;
+} CDCCSInterfaceDescriptor4;
+
+typedef struct
+{
+ IADDescriptor iad; // Only needed on compound device
+
+ // Control
+ InterfaceDescriptor cif; //
+ CDCCSInterfaceDescriptor header;
+ CDCCSInterfaceDescriptor callManagement;
+ CDCCSInterfaceDescriptor4 controlManagement;
+ CDCCSInterfaceDescriptor functionalDescriptor;
+ EndpointDescriptor cifin;
+
+ // Data
+ InterfaceDescriptor dif;
+ EndpointDescriptor in;
+ EndpointDescriptor out;
+} CDCDescriptor;
+
+typedef struct
+{
+ InterfaceDescriptor msc;
+ EndpointDescriptor in;
+ EndpointDescriptor out;
+} MSCDescriptor;
+
+typedef struct
+{
+ u8 len; // 9
+ u8 dtype; // 0x21
+ u8 addr;
+ u8 versionL; // 0x101
+ u8 versionH; // 0x101
+ u8 country;
+ u8 desctype; // 0x22 report
+ u8 descLenL;
+ u8 descLenH;
+} HIDDescDescriptor;
+
+typedef struct
+{
+ InterfaceDescriptor hid;
+ HIDDescDescriptor desc;
+ EndpointDescriptor in;
+} HIDDescriptor;
+
+#define D_DEVICE(_class,_subClass,_proto,_packetSize0,_vid,_pid,_version,_im,_ip,_is,_configs) \
+ { 18, 1, 0x200, _class,_subClass,_proto,_packetSize0,_vid,_pid,_version,_im,_ip,_is,_configs }
+
+#define D_CONFIG(_totalLength,_interfaces) \
+ { 9, 2, _totalLength,_interfaces, 1, 0, USB_CONFIG_BUS_POWERED, USB_CONFIG_POWER_MA(100) }
+
+#define D_INTERFACE(_n,_numEndpoints,_class,_subClass,_protocol) \
+ { 9, 4, _n, 0, _numEndpoints, _class,_subClass, _protocol, 0 }
+
+#define D_ENDPOINT(_addr,_attr,_packetSize, _interval) \
+ { 7, 5, _addr,_attr,_packetSize, _interval }
+
+#define D_IAD(_firstInterface, _count, _class, _subClass, _protocol) \
+ { 8, 11, _firstInterface, _count, _class, _subClass, _protocol, 0 }
+
+#define D_HIDREPORT(_descriptorLength) \
+ { 9, 0x21, 0x1, 0x1, 0, 1, 0x22, _descriptorLength, 0 }
+
+#define D_CDCCS(_subtype,_d0,_d1) { 5, 0x24, _subtype, _d0, _d1 }
+#define D_CDCCS4(_subtype,_d0) { 4, 0x24, _subtype, _d0 }
+
+#endif \ No newline at end of file
diff --git a/bootloaders/diskloader/src/USBDesc.cpp b/bootloaders/diskloader/src/USBDesc.cpp
new file mode 100644
index 0000000..dfde01d
--- /dev/null
+++ b/bootloaders/diskloader/src/USBDesc.cpp
@@ -0,0 +1,88 @@
+
+
+/* Copyright (c) 2011, Peter Barrett
+**
+** Permission to use, copy, modify, and/or distribute this software for
+** any purpose with or without fee is hereby granted, provided that the
+** above copyright notice and this permission notice appear in all copies.
+**
+** THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
+** WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
+** WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR
+** BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES
+** OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
+** WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION,
+** ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS
+** SOFTWARE.
+*/
+
+#include "Platform.h"
+
+//====================================================================================================
+//====================================================================================================
+// Actual device descriptors
+
+const u16 STRING_LANGUAGE[2] = {
+ (3<<8) | (2+2),
+ 0x0409 // English
+};
+
+#if 0
+const u16 STRING_PRODUCT[] = {
+ (3<<8) | (2+2*10),
+ 'M','i','c','r','o','t','o','u','c','h'
+};
+#endif
+
+const u16 STRING_SERIAL[13] = {
+ (3<<8) | (2+2*12),
+ MSC_DISK_SERIAL
+};
+
+
+//#ifdef CDC_ENABLED
+DeviceDescriptor USB_DeviceDescriptorA = D_DEVICE(0X02,0X00,0X00,64,USB_VID,USB_PID,0x100,0,IPRODUCT,ISERIAL,1);
+//#else
+DeviceDescriptor USB_DeviceDescriptor = D_DEVICE(0x00,0x00,0x00,64,USB_VID,USB_PID,0x100,0,IPRODUCT,ISERIAL,1);
+//#endif
+
+Config USB_ConfigDescriptor =
+{
+ D_CONFIG(sizeof(Config),INTERFACE_COUNT),
+
+#ifdef CDC_ENABLED
+ // CDC
+ {
+ D_IAD(0,2,CDC_COMMUNICATION_INTERFACE_CLASS,CDC_ABSTRACT_CONTROL_MODEL,1),
+
+ // CDC communication interface
+ D_INTERFACE(CDC_ACM_INTERFACE,1,CDC_COMMUNICATION_INTERFACE_CLASS,CDC_ABSTRACT_CONTROL_MODEL,0),
+ D_CDCCS(CDC_HEADER,0x10,0x01), // Header (1.10 bcd)
+ D_CDCCS(CDC_CALL_MANAGEMENT,1,1), // Device handles call management
+ D_CDCCS4(CDC_ABSTRACT_CONTROL_MANAGEMENT,2), // SET_LINE_CODING, GET_LINE_CODING, SET_CONTROL_LINE_STATE supported
+ D_CDCCS(CDC_UNION,CDC_ACM_INTERFACE,CDC_DATA_INTERFACE), // Communication interface is master, data interface is slave 0
+ D_ENDPOINT(USB_ENDPOINT_IN (CDC_ENDPOINT_ACM),USB_ENDPOINT_TYPE_INTERRUPT,0x10,0x40),
+
+ // CDC data interface
+ D_INTERFACE(CDC_DATA_INTERFACE,2,CDC_DATA_INTERFACE_CLASS,0,0),
+ D_ENDPOINT(USB_ENDPOINT_OUT(CDC_ENDPOINT_OUT),USB_ENDPOINT_TYPE_BULK,0x40,0),
+ D_ENDPOINT(USB_ENDPOINT_IN (CDC_ENDPOINT_IN ),USB_ENDPOINT_TYPE_BULK,0x40,0)
+ },
+#endif
+ // HID
+ {
+ D_INTERFACE(HID_INTERFACE,1,3,0,0),
+ D_HIDREPORT(30),
+ D_ENDPOINT(USB_ENDPOINT_IN (HID_ENDPOINT_INT),USB_ENDPOINT_TYPE_INTERRUPT,0x40,0x40)
+ },
+
+#ifdef MSC_ENABLED
+ // Mass Storage
+ {
+ D_INTERFACE(MSC_INTERFACE,2,USB_DEVICE_CLASS_STORAGE,MSC_SUBCLASS_SCSI,MSC_PROTOCOL_BULK_ONLY),
+ D_ENDPOINT(USB_ENDPOINT_OUT(MSC_ENDPOINT_OUT),USB_ENDPOINT_TYPE_BULK,0x40,0),
+ D_ENDPOINT(USB_ENDPOINT_IN (MSC_ENDPOINT_IN ),USB_ENDPOINT_TYPE_BULK,0x40,0)
+ }
+#endif
+};
+
diff --git a/bootloaders/diskloader/src/USBDesc.h b/bootloaders/diskloader/src/USBDesc.h
new file mode 100644
index 0000000..a551d69
--- /dev/null
+++ b/bootloaders/diskloader/src/USBDesc.h
@@ -0,0 +1,81 @@
+
+
+/* Copyright (c) 2011, Peter Barrett
+**
+** Permission to use, copy, modify, and/or distribute this software for
+** any purpose with or without fee is hereby granted, provided that the
+** above copyright notice and this permission notice appear in all copies.
+**
+** THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
+** WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
+** WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR
+** BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES
+** OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
+** WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION,
+** ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS
+** SOFTWARE.
+*/
+
+
+#ifndef CDC_ENABLED
+
+#define MSC_INTERFACE 0 // MSC Interface
+#define MSC_ENDPOINT_OUT 1
+#define MSC_ENDPOINT_IN 2
+
+#define INTERFACE_COUNT 1 // 1 for msc
+
+#else
+
+#define CDC_ACM_INTERFACE 0 // CDC ACM
+#define CDC_DATA_INTERFACE 1 // CDC Data
+#define CDC_ENDPOINT_ACM 1
+#define CDC_ENDPOINT_OUT 2
+#define CDC_ENDPOINT_IN 3
+
+#define HID_INTERFACE 2 // HID Interface
+#define HID_ENDPOINT_INT 4
+
+#ifdef MSC_ENABLED
+
+#define MSC_INTERFACE 3 // MSC Interface
+#define MSC_ENDPOINT_OUT 5
+#define MSC_ENDPOINT_IN 6
+#define INTERFACE_COUNT 4 // 2 for cdc + 1 for hid + 1 for msc
+
+#else
+
+#define INTERFACE_COUNT 3 // 2 for cdc + 1 for hid
+
+#endif
+
+#endif
+
+typedef struct
+{
+ ConfigDescriptor config;
+#ifdef CDC_ENABLED
+ CDCDescriptor cdc;
+#endif
+ HIDDescriptor hid;
+#ifdef MSC_ENABLED
+ MSCDescriptor msc;
+#endif
+} Config;
+
+extern Config USB_ConfigDescriptor PROGMEM;
+extern DeviceDescriptor USB_DeviceDescriptor PROGMEM;
+extern DeviceDescriptor USB_DeviceDescriptorA PROGMEM;
+
+extern const u16 STRING_LANGUAGE[2] PROGMEM;
+extern const u16 STRING_SERIAL[13] PROGMEM;
+
+#define IMANUFACTURER 0
+#define IPRODUCT 0
+#define ISERIAL 1 // Only need this for MSC
+
+
+#define MSC_TX MSC_ENDPOINT_IN
+#define MSC_RX MSC_ENDPOINT_OUT
+#define CDC_TX CDC_ENDPOINT_IN
+#define CDC_RX CDC_ENDPOINT_OUT \ No newline at end of file
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-11-22 21:58:42 +0000