diff options
3 files changed, 79 insertions, 22 deletions
diff --git a/libraries/Bridge/examples/Process/Process.ino b/libraries/Bridge/examples/Process/Process.ino index 248db39..25e45c7 100644 --- a/libraries/Bridge/examples/Process/Process.ino +++ b/libraries/Bridge/examples/Process/Process.ino @@ -1,25 +1,61 @@ +/* + Running process using Process class. + + This sketch demonstrate how to run linux processes + using an Arduino Yún. + + created 5 Jun 2013 + by Cristian Maglie + + */ + #include <Process.h> void setup() { - pinMode(13,OUTPUT); - digitalWrite(13,LOW); - - Serial.begin(9600); + // Setup Bridge (needed every time we communicate with the Arduino Yún) Bridge.begin(); + // Setup Console + Console.begin(); + Console.buffer(64); + // Wait until a Network Monitor is connected. + while (!Console); + + // run various example processes + runCurl(); + runCpuInfo(); +} - digitalWrite(13,HIGH); - delay(2000); - +void loop() { + // Do nothing here. +} + +void runCurl() { + // Launch "curl" command and get Arduino asciilogo from the network Process p; p.begin("curl"); p.addParameter("http://arduino.cc/asciilogo.txt"); p.run(); - + + // Print arduino logo over the console while (p.available()>0) { char c = p.read(); - Serial.print(c); + Console.print(c); } + Console.flush(); } -void loop() { +void runCpuInfo() { + // Launch "cat /proc/cpuinfo" command (shows info on Atheros CPU) + Process p; + p.begin("cat"); + p.addParameter("/proc/cpuinfo"); + p.run(); + + // Print command output on the Console + while (p.available()>0) { + char c = p.read(); + Console.print(c); + } + Console.flush(); } + diff --git a/libraries/Bridge/examples/XivelyClient/XivelyClient.ino b/libraries/Bridge/examples/XivelyClient/XivelyClient.ino index 67079de..48b1403 100644 --- a/libraries/Bridge/examples/XivelyClient/XivelyClient.ino +++ b/libraries/Bridge/examples/XivelyClient/XivelyClient.ino @@ -38,7 +38,7 @@ void setup() { while(!Console); // wait for Network Console to open Console.println("Xively client"); - // Do a first update immediatly + // Do a first update immediately updateData(); sendData(); lastRequest = millis(); @@ -80,7 +80,7 @@ void sendData() { // Send the HTTP PUT request // Is better to declare the Process here, so when the - // sendData function finishes the resources are immediatly + // sendData function finishes the resources are immediately // released. Declaring it global works too, BTW. Process xively; Console.print("\n\nSending data... "); diff --git a/libraries/Bridge/examples/YunSerialTerminal/YunSerialTerminal.ino b/libraries/Bridge/examples/YunSerialTerminal/YunSerialTerminal.ino index dea2ef5..aa152e1 100644 --- a/libraries/Bridge/examples/YunSerialTerminal/YunSerialTerminal.ino +++ b/libraries/Bridge/examples/YunSerialTerminal/YunSerialTerminal.ino @@ -1,9 +1,8 @@ - /* Arduino Yun USB-to-Serial Allows you to use the Yun's 32U4 processor as a - serial terminal for the linino processor + serial terminal for the linino processor. Upload this to an Arduino Yun via serial (not WiFi) then open the serial monitor at 115200 to see the boot process @@ -11,28 +10,31 @@ as a basic command line interface for the linino processor using this sketch. + From the serial monitor the following commands can be issued: + + '~' followed by '0' -> Set the UART speed to 57600 baud + '~' followed by '1' -> Set the UART speed to 115200 baud + The circuit: * Arduino Yun created March 2013 by Massimo Banzi + modified by Cristian Maglie This example code is in the public domain. */ -long baud = 115200; +long lininoBaud = 57600; // Pin 13 has an LED connected on most Arduino boards. -// give it a name: int led = 13; int ledState = HIGH; // whether the LED is high or low void setup() { - Serial.begin(baud); // open serial connection to Linino - Serial1.begin(baud); // open serial connection via USB-Serial - Serial.println("Prova"); // Hello USB - Serial1.println("Prova1"); // Hello Linino + Serial.begin(115200); // open serial connection via USB-Serial + Serial1.begin(lininoBaud); // open serial connection to Linino // initialize the digital pin as an output. pinMode(led, OUTPUT); @@ -40,12 +42,31 @@ void setup() { } -void loop() { +boolean commandMode = false; +void loop() { // copy from virtual serial line to uart and vice versa if (Serial.available()) { // got anything from USB-Serial? char c = (char)Serial.read(); // read from USB-serial - Serial1.write(c); // write to Linino + if (commandMode == false) { // if we aren't in command mode... + if (c == '~') { // Tilde '~' key pressed? + commandMode = true; // enter in command mode + } else { + Serial1.write(c); // otherwise write char to Linino + } + } else { // if we are in command mode... + if (c == '0') { // '0' key pressed? + Serial1.begin(57600); // set speed to 57600 + Serial.println("Speed set to 57600"); + } else if (c == '1') { // '1' key pressed? + Serial1.begin(115200); // set speed to 115200 + Serial.println("Speed set to 115200"); + } else { // any other key pressed? + Serial1.write('~'); // write '~' to Linino + Serial1.write(c); // write char to Linino + } + commandMode = false; // in all cases exit from command mode + } ledState=!ledState; // invert LED state digitalWrite(led, ledState); // toggle the LED } |