Moved libraries folder inside platform folder. Now libraries and examples are searched per board/platform

6 files changed, 495 insertions, 0 deletions

diff --git a/libraries/SD/examples/CardInfo/CardInfo.ino b/libraries/SD/examples/CardInfo/CardInfo.ino
new file mode 100644
index 0000000..fb2f6c3
--- /dev/null
+++ b/libraries/SD/examples/CardInfo/CardInfo.ino
@@ -0,0 +1,111 @@
+/*
+  SD card test 
+   
+ This example shows how use the utility libraries on which the'
+ SD library is based in order to get info about your SD card.
+ Very useful for testing a card when you're not sure whether its working or not.
+ 	
+ The circuit:
+  * SD card attached to SPI bus as follows:
+ ** MOSI - pin 11 on Arduino Uno/Duemilanove/Diecimila
+ ** MISO - pin 12 on Arduino Uno/Duemilanove/Diecimila
+ ** CLK - pin 13 on Arduino Uno/Duemilanove/Diecimila
+ ** CS - depends on your SD card shield or module. 
+ 		Pin 4 used here for consistency with other Arduino examples
+
+ 
+ created  28 Mar 2011
+ by Limor Fried 
+ modified 16 Mar 2011
+ by Tom Igoe
+ */
+ // include the SD library:
+#include <SD.h>
+
+// set up variables using the SD utility library functions:
+Sd2Card card;
+SdVolume volume;
+SdFile root;
+
+// change this to match your SD shield or module;
+// Arduino Ethernet shield: pin 4
+// Adafruit SD shields and modules: pin 10
+// Sparkfun SD shield: pin 8
+const int chipSelect = 4;    
+
+void setup()
+{
+  Serial.begin(9600);
+  Serial.print("\nInitializing SD card...");
+  // On the Ethernet Shield, CS is pin 4. It's set as an output by default.
+  // Note that even if it's not used as the CS pin, the hardware SS pin 
+  // (10 on most Arduino boards, 53 on the Mega) must be left as an output 
+  // or the SD library functions will not work. 
+  pinMode(10, OUTPUT);     // change this to 53 on a mega
+
+
+  // we'll use the initialization code from the utility libraries
+  // since we're just testing if the card is working!
+  if (!card.init(SPI_HALF_SPEED, chipSelect)) {
+    Serial.println("initialization failed. Things to check:");
+    Serial.println("* is a card is inserted?");
+    Serial.println("* Is your wiring correct?");
+    Serial.println("* did you change the chipSelect pin to match your shield or module?");
+    return;
+  } else {
+   Serial.println("Wiring is correct and a card is present."); 
+  }
+
+  // print the type of card
+  Serial.print("\nCard type: ");
+  switch(card.type()) {
+    case SD_CARD_TYPE_SD1:
+      Serial.println("SD1");
+      break;
+    case SD_CARD_TYPE_SD2:
+      Serial.println("SD2");
+      break;
+    case SD_CARD_TYPE_SDHC:
+      Serial.println("SDHC");
+      break;
+    default:
+      Serial.println("Unknown");
+  }
+
+  // Now we will try to open the 'volume'/'partition' - it should be FAT16 or FAT32
+  if (!volume.init(card)) {
+    Serial.println("Could not find FAT16/FAT32 partition.\nMake sure you've formatted the card");
+    return;
+  }
+
+
+  // print the type and size of the first FAT-type volume
+  uint32_t volumesize;
+  Serial.print("\nVolume type is FAT");
+  Serial.println(volume.fatType(), DEC);
+  Serial.println();
+  
+  volumesize = volume.blocksPerCluster();    // clusters are collections of blocks
+  volumesize *= volume.clusterCount();       // we'll have a lot of clusters
+  volumesize *= 512;                            // SD card blocks are always 512 bytes
+  Serial.print("Volume size (bytes): ");
+  Serial.println(volumesize);
+  Serial.print("Volume size (Kbytes): ");
+  volumesize /= 1024;
+  Serial.println(volumesize);
+  Serial.print("Volume size (Mbytes): ");
+  volumesize /= 1024;
+  Serial.println(volumesize);
+
+  
+  Serial.println("\nFiles found on the card (name, date and size in bytes): ");
+  root.openRoot(volume);
+  
+  // list all files in the card with date and size
+  root.ls(LS_R | LS_DATE | LS_SIZE);
+}
+
+
+void loop(void) {
+  
+}
diff --git a/libraries/SD/examples/Datalogger/Datalogger.ino b/libraries/SD/examples/Datalogger/Datalogger.ino
new file mode 100644
index 0000000..73d81af
--- /dev/null
+++ b/libraries/SD/examples/Datalogger/Datalogger.ino
@@ -0,0 +1,86 @@
+/*
+  SD card datalogger
+ 
+ This example shows how to log data from three analog sensors 
+ to an SD card using the SD library.
+ 	
+ The circuit:
+ * analog sensors on analog ins 0, 1, and 2
+ * SD card attached to SPI bus as follows:
+ ** MOSI - pin 11
+ ** MISO - pin 12
+ ** CLK - pin 13
+ ** CS - pin 4
+ 
+ created  24 Nov 2010
+ updated 2 Dec 2010
+ by Tom Igoe
+ 
+ This example code is in the public domain.
+ 	 
+ */
+
+#include <SD.h>
+
+// On the Ethernet Shield, CS is pin 4. Note that even if it's not
+// used as the CS pin, the hardware CS pin (10 on most Arduino boards,
+// 53 on the Mega) must be left as an output or the SD library
+// functions will not work.
+const int chipSelect = 4;
+
+void setup()
+{
+  Serial.begin(9600);
+  Serial.print("Initializing SD card...");
+  // make sure that the default chip select pin is set to
+  // output, even if you don't use it:
+  pinMode(10, OUTPUT);
+  
+  // see if the card is present and can be initialized:
+  if (!SD.begin(chipSelect)) {
+    Serial.println("Card failed, or not present");
+    // don't do anything more:
+    return;
+  }
+  Serial.println("card initialized.");
+}
+
+void loop()
+{
+  // make a string for assembling the data to log:
+  String dataString = "";
+
+  // read three sensors and append to the string:
+  for (int analogPin = 0; analogPin < 3; analogPin++) {
+    int sensor = analogRead(analogPin);
+    dataString += String(sensor);
+    if (analogPin < 2) {
+      dataString += ","; 
+    }
+  }
+
+  // open the file. note that only one file can be open at a time,
+  // so you have to close this one before opening another.
+  File dataFile = SD.open("datalog.txt", FILE_WRITE);
+
+  // if the file is available, write to it:
+  if (dataFile) {
+    dataFile.println(dataString);
+    dataFile.close();
+    // print to the serial port too:
+    Serial.println(dataString);
+  }  
+  // if the file isn't open, pop up an error:
+  else {
+    Serial.println("error opening datalog.txt");
+  } 
+}
+
+
+
+
+
+
+
+
+
diff --git a/libraries/SD/examples/DumpFile/DumpFile.ino b/libraries/SD/examples/DumpFile/DumpFile.ino
new file mode 100644
index 0000000..961717f
--- /dev/null
+++ b/libraries/SD/examples/DumpFile/DumpFile.ino
@@ -0,0 +1,64 @@
+/*
+  SD card file dump
+ 
+ This example shows how to read a file from the SD card using the
+ SD library and send it over the serial port.
+ 	
+ The circuit:
+ * SD card attached to SPI bus as follows:
+ ** MOSI - pin 11
+ ** MISO - pin 12
+ ** CLK - pin 13
+ ** CS - pin 4
+ 
+ created  22 December 2010
+ 
+ This example code is in the public domain.
+ 	 
+ */
+
+#include <SD.h>
+
+// On the Ethernet Shield, CS is pin 4. Note that even if it's not
+// used as the CS pin, the hardware CS pin (10 on most Arduino boards,
+// 53 on the Mega) must be left as an output or the SD library
+// functions will not work.
+const int chipSelect = 4;
+
+void setup()
+{
+  Serial.begin(9600);
+  Serial.print("Initializing SD card...");
+  // make sure that the default chip select pin is set to
+  // output, even if you don't use it:
+  pinMode(10, OUTPUT);
+  
+  // see if the card is present and can be initialized:
+  if (!SD.begin(chipSelect)) {
+    Serial.println("Card failed, or not present");
+    // don't do anything more:
+    return;
+  }
+  Serial.println("card initialized.");
+  
+  // open the file. note that only one file can be open at a time,
+  // so you have to close this one before opening another.
+  File dataFile = SD.open("datalog.txt");
+
+  // if the file is available, write to it:
+  if (dataFile) {
+    while (dataFile.available()) {
+      Serial.write(dataFile.read());
+    }
+    dataFile.close();
+  }  
+  // if the file isn't open, pop up an error:
+  else {
+    Serial.println("error opening datalog.txt");
+  } 
+}
+
+void loop()
+{
+}
+
diff --git a/libraries/SD/examples/Files/Files.ino b/libraries/SD/examples/Files/Files.ino
new file mode 100644
index 0000000..5ed9fea
--- /dev/null
+++ b/libraries/SD/examples/Files/Files.ino
@@ -0,0 +1,78 @@
+/*
+  SD card basic file example
+ 
+ This example shows how to create and destroy an SD card file 	
+ The circuit:
+ * SD card attached to SPI bus as follows:
+ ** MOSI - pin 11
+ ** MISO - pin 12
+ ** CLK - pin 13
+ ** CS - pin 4
+ 
+ created   Nov 2010
+ by David A. Mellis
+ updated 2 Dec 2010
+ by Tom Igoe
+ 
+ This example code is in the public domain.
+ 	 
+ */
+#include <SD.h>
+
+File myFile;
+
+void setup()
+{
+  Serial.begin(9600);
+  Serial.print("Initializing SD card...");
+  // On the Ethernet Shield, CS is pin 4. It's set as an output by default.
+  // Note that even if it's not used as the CS pin, the hardware SS pin 
+  // (10 on most Arduino boards, 53 on the Mega) must be left as an output 
+  // or the SD library functions will not work. 
+  pinMode(10, OUTPUT);
+
+  if (!SD.begin(4)) {
+    Serial.println("initialization failed!");
+    return;
+  }
+  Serial.println("initialization done.");
+
+  if (SD.exists("example.txt")) {
+    Serial.println("example.txt exists.");
+  }
+  else {
+    Serial.println("example.txt doesn't exist.");
+  }
+
+  // open a new file and immediately close it:
+  Serial.println("Creating example.txt...");
+  myFile = SD.open("example.txt", FILE_WRITE);
+  myFile.close();
+
+  // Check to see if the file exists: 
+  if (SD.exists("example.txt")) {
+    Serial.println("example.txt exists.");
+  }
+  else {
+    Serial.println("example.txt doesn't exist.");  
+  }
+
+  // delete the file:
+  Serial.println("Removing example.txt...");
+  SD.remove("example.txt");
+
+  if (SD.exists("example.txt")){ 
+    Serial.println("example.txt exists.");
+  }
+  else {
+    Serial.println("example.txt doesn't exist.");  
+  }
+}
+
+void loop()
+{
+  // nothing happens after setup finishes.
+}
+
+
+
diff --git a/libraries/SD/examples/ReadWrite/ReadWrite.ino b/libraries/SD/examples/ReadWrite/ReadWrite.ino
new file mode 100644
index 0000000..9957218
--- /dev/null
+++ b/libraries/SD/examples/ReadWrite/ReadWrite.ino
@@ -0,0 +1,79 @@
+/*
+  SD card read/write
+ 
+ This example shows how to read and write data to and from an SD card file 	
+ The circuit:
+ * SD card attached to SPI bus as follows:
+ ** MOSI - pin 11
+ ** MISO - pin 12
+ ** CLK - pin 13
+ ** CS - pin 4
+ 
+ created   Nov 2010
+ by David A. Mellis
+ updated 2 Dec 2010
+ by Tom Igoe
+ 
+ This example code is in the public domain.
+ 	 
+ */
+ 
+#include <SD.h>
+
+File myFile;
+
+void setup()
+{
+  Serial.begin(9600);
+  Serial.print("Initializing SD card...");
+  // On the Ethernet Shield, CS is pin 4. It's set as an output by default.
+  // Note that even if it's not used as the CS pin, the hardware SS pin 
+  // (10 on most Arduino boards, 53 on the Mega) must be left as an output 
+  // or the SD library functions will not work. 
+   pinMode(10, OUTPUT);
+   
+  if (!SD.begin(4)) {
+    Serial.println("initialization failed!");
+    return;
+  }
+  Serial.println("initialization done.");
+  
+  // open the file. note that only one file can be open at a time,
+  // so you have to close this one before opening another.
+  myFile = SD.open("test.txt", FILE_WRITE);
+  
+  // if the file opened okay, write to it:
+  if (myFile) {
+    Serial.print("Writing to test.txt...");
+    myFile.println("testing 1, 2, 3.");
+	// close the file:
+    myFile.close();
+    Serial.println("done.");
+  } else {
+    // if the file didn't open, print an error:
+    Serial.println("error opening test.txt");
+  }
+  
+  // re-open the file for reading:
+  myFile = SD.open("test.txt");
+  if (myFile) {
+    Serial.println("test.txt:");
+    
+    // read from the file until there's nothing else in it:
+    while (myFile.available()) {
+    	Serial.write(myFile.read());
+    }
+    // close the file:
+    myFile.close();
+  } else {
+  	// if the file didn't open, print an error:
+    Serial.println("error opening test.txt");
+  }
+}
+
+void loop()
+{
+	// nothing happens after setup
+}
+
+
diff --git a/libraries/SD/examples/listfiles/listfiles.ino b/libraries/SD/examples/listfiles/listfiles.ino
new file mode 100644
index 0000000..b2435a2
--- /dev/null
+++ b/libraries/SD/examples/listfiles/listfiles.ino
@@ -0,0 +1,77 @@
+/*
+  SD card basic file example
+ 
+ This example shows how to create and destroy an SD card file 	
+ The circuit:
+ * SD card attached to SPI bus as follows:
+ ** MOSI - pin 11
+ ** MISO - pin 12
+ ** CLK - pin 13
+ ** CS - pin 4
+ 
+ created   Nov 2010
+ by David A. Mellis
+ updated 2 Dec 2010
+ by Tom Igoe
+ 
+ This example code is in the public domain.
+ 	 
+ */
+#include <SD.h>
+
+File root;
+
+void setup()
+{
+  Serial.begin(9600);
+  Serial.print("Initializing SD card...");
+  // On the Ethernet Shield, CS is pin 4. It's set as an output by default.
+  // Note that even if it's not used as the CS pin, the hardware SS pin 
+  // (10 on most Arduino boards, 53 on the Mega) must be left as an output 
+  // or the SD library functions will not work. 
+  pinMode(10, OUTPUT);
+
+  if (!SD.begin(10)) {
+    Serial.println("initialization failed!");
+    return;
+  }
+  Serial.println("initialization done.");
+
+  root = SD.open("/");
+  
+  printDirectory(root, 0);
+  
+  Serial.println("done!");
+}
+
+void loop()
+{
+  // nothing happens after setup finishes.
+}
+
+void printDirectory(File dir, int numTabs) {
+   while(true) {
+     
+     File entry =  dir.openNextFile();
+     if (! entry) {
+       // no more files
+       //Serial.println("**nomorefiles**");
+       break;
+     }
+     for (uint8_t i=0; i<numTabs; i++) {
+       Serial.print('\t');
+     }
+     Serial.print(entry.name());
+     if (entry.isDirectory()) {
+       Serial.println("/");
+       printDirectory(entry, numTabs+1);
+     } else {
+       // files have sizes, directories do not
+       Serial.print("\t\t");
+       Serial.println(entry.size(), DEC);
+     }
+   }
+}
+
+
+