Moving libraries out of arduino platform / core directory and to top-level.

14 files changed, 0 insertions, 2808 deletions

diff --git a/libraries/Firmata/examples/AnalogFirmata/AnalogFirmata.pde b/libraries/Firmata/examples/AnalogFirmata/AnalogFirmata.pde
deleted file mode 100644
index ab83726..0000000
--- a/libraries/Firmata/examples/AnalogFirmata/AnalogFirmata.pde
+++ /dev/null
@@ -1,83 +0,0 @@
-/* This firmware supports as many analog ports as possible, all analog inputs,
- * four PWM outputs, and two with servo support.
- *
- * This example code is in the public domain.
- */
-#include <Firmata.h>
-#include <Servo.h>
-
-/*==============================================================================
- * GLOBAL VARIABLES
- *============================================================================*/
-
-/* servos */
-Servo servo9, servo10; // one instance per pin
-/* analog inputs */
-int analogInputsToReport = 0; // bitwise array to store pin reporting
-int analogPin = 0; // counter for reading analog pins
-/* timer variables */
-unsigned long currentMillis;     // store the current value from millis()
-unsigned long nextExecuteMillis; // for comparison with currentMillis
-
-
-/*==============================================================================
- * FUNCTIONS                                                                
- *============================================================================*/
-
-void analogWriteCallback(byte pin, int value)
-{
-    switch(pin) {
-    case 9: servo9.write(value); break;
-    case 10: servo10.write(value); break;
-    case 3: 
-    case 5: 
-    case 6: 
-    case 11: // PWM pins
-        analogWrite(pin, value); 
-        break;
-    }
-}
-// -----------------------------------------------------------------------------
-// sets bits in a bit array (int) to toggle the reporting of the analogIns
-void reportAnalogCallback(byte pin, int value)
-{
-    if(value == 0) {
-        analogInputsToReport = analogInputsToReport &~ (1 << pin);
-    }
-    else { // everything but 0 enables reporting of that pin
-        analogInputsToReport = analogInputsToReport | (1 << pin);
-    }
-    // TODO: save status to EEPROM here, if changed
-}
-
-/*==============================================================================
- * SETUP()
- *============================================================================*/
-void setup() 
-{
-    Firmata.setFirmwareVersion(0, 2);
-    Firmata.attach(ANALOG_MESSAGE, analogWriteCallback);
-    Firmata.attach(REPORT_ANALOG, reportAnalogCallback);
-
-    servo9.attach(9);
-    servo10.attach(10);
-    Firmata.begin(57600);
-}
-
-/*==============================================================================
- * LOOP()
- *============================================================================*/
-void loop() 
-{
-    while(Firmata.available())
-        Firmata.processInput();
-    currentMillis = millis();
-    if(currentMillis > nextExecuteMillis) {  
-        nextExecuteMillis = currentMillis + 19; // run this every 20ms
-        for(analogPin=0;analogPin<TOTAL_ANALOG_PINS;analogPin++) {
-            if( analogInputsToReport & (1 << analogPin) ) 
-                Firmata.sendAnalog(analogPin, analogRead(analogPin));
-        }
-    }
-}
-
diff --git a/libraries/Firmata/examples/AnalogFirmata/Makefile b/libraries/Firmata/examples/AnalogFirmata/Makefile
deleted file mode 100644
index e968c0a..0000000
--- a/libraries/Firmata/examples/AnalogFirmata/Makefile
+++ /dev/null
@@ -1,263 +0,0 @@
-# Arduino makefile
-#
-# This makefile allows you to build sketches from the command line
-# without the Arduino environment (or Java).
-#
-# The Arduino environment does preliminary processing on a sketch before
-# compiling it.  If you're using this makefile instead, you'll need to do
-# a few things differently:
-#
-#   - Give your program's file a .cpp extension (e.g. foo.cpp).
-#
-#   - Put this line at top of your code: #include <WProgram.h>
-#
-#   - Write prototypes for all your functions (or define them before you
-#     call them).  A prototype declares the types of parameters a
-#     function will take and what type of value it will return.  This
-#     means that you can have a call to a function before the definition
-#     of the function.  A function prototype looks like the first line of
-#     the function, with a semi-colon at the end.  For example:
-#     int digitalRead(int pin);
-#
-# Instructions for using the makefile:
-#
-#  1. Copy this file into the folder with your sketch.
-#
-#  2. Below, modify the line containing "TARGET" to refer to the name of
-#     of your program's file without an extension (e.g. TARGET = foo).
-#
-#  3. Modify the line containg "ARDUINO" to point the directory that
-#     contains the Arduino core (for normal Arduino installations, this
-#     is the hardware/cores/arduino sub-directory).
-#
-#  4. Modify the line containing "PORT" to refer to the filename
-#     representing the USB or serial connection to your Arduino board
-#     (e.g. PORT = /dev/tty.USB0).  If the exact name of this file
-#     changes, you can use * as a wildcard (e.g. PORT = /dev/tty.USB*).
-#
-#  5. At the command line, change to the directory containing your
-#     program's file and the makefile.
-#
-#  6. Type "make" and press enter to compile/verify your program.
-#
-#  7. Type "make upload", reset your Arduino board, and press enter  to
-#     upload your program to the Arduino board.
-#
-# $Id: Makefile,v 1.7 2007/04/13 05:28:23 eighthave Exp $
-
-PORT = /dev/tty.usbserial-*
-TARGET := $(shell pwd | sed 's|.*/\(.*\)|\1|')
-ARDUINO = /Applications/arduino
-ARDUINO_SRC = $(ARDUINO)/hardware/cores/arduino
-ARDUINO_LIB_SRC = $(ARDUINO)/hardware/libraries
-INCLUDE = -I$(ARDUINO_SRC) -I$(ARDUINO)/hardware/tools/avr/avr/include \
-	-I$(ARDUINO_LIB_SRC)/EEPROM \
-	-I$(ARDUINO_LIB_SRC)/Firmata \
-	-I$(ARDUINO_LIB_SRC)/Servo \
-	-I$(ARDUINO_LIB_SRC)
-SRC = $(wildcard $(ARDUINO_SRC)/*.c)
-CXXSRC = applet/$(TARGET).cpp $(ARDUINO_SRC)/HardwareSerial.cpp \
-	$(ARDUINO_LIB_SRC)/EEPROM/EEPROM.cpp \
-	$(ARDUINO_LIB_SRC)/Firmata/Firmata.cpp \
-	$(ARDUINO_LIB_SRC)/Servo/Servo.cpp \
-	$(ARDUINO_SRC)/WMath.cpp
-HEADERS = $(wildcard $(ARDUINO_SRC)/*.h) $(wildcard $(ARDUINO_LIB_SRC)/*/*.h)
-
-MCU = atmega168
-#MCU = atmega8
-F_CPU = 16000000
-FORMAT = ihex
-UPLOAD_RATE = 19200
-
-# Name of this Makefile (used for "make depend").
-MAKEFILE = Makefile
-
-# Debugging format.
-# Native formats for AVR-GCC's -g are stabs [default], or dwarf-2.
-# AVR (extended) COFF requires stabs, plus an avr-objcopy run.
-DEBUG = stabs
-
-OPT = s
-
-# Place -D or -U options here
-CDEFS = -DF_CPU=$(F_CPU)
-CXXDEFS = -DF_CPU=$(F_CPU)
-
-# Compiler flag to set the C Standard level.
-# c89   - "ANSI" C
-# gnu89 - c89 plus GCC extensions
-# c99   - ISO C99 standard (not yet fully implemented)
-# gnu99 - c99 plus GCC extensions
-CSTANDARD = -std=gnu99
-CDEBUG = -g$(DEBUG)
-CWARN = -Wall -Wstrict-prototypes
-CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums
-#CEXTRA = -Wa,-adhlns=$(<:.c=.lst)
-
-CFLAGS = $(CDEBUG) $(CDEFS) $(INCLUDE) -O$(OPT) $(CWARN) $(CSTANDARD) $(CEXTRA)
-CXXFLAGS = $(CDEFS) $(INCLUDE) -O$(OPT)
-#ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs 
-LDFLAGS = 
-
-
-# Programming support using avrdude. Settings and variables.
-AVRDUDE_PROGRAMMER = stk500
-AVRDUDE_PORT = $(PORT)
-AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex
-AVRDUDE_FLAGS = -F -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) \
-  -b $(UPLOAD_RATE) -q -V
-
-# Program settings
-CC = avr-gcc
-CXX = avr-g++
-OBJCOPY = avr-objcopy
-OBJDUMP = avr-objdump
-SIZE = avr-size
-NM = avr-nm
-AVRDUDE = avrdude
-REMOVE = rm -f
-MV = mv -f
-
-# Define all object files.
-OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o)
-
-# Define all listing files.
-LST = $(ASRC:.S=.lst) $(CXXSRC:.cpp=.lst) $(SRC:.c=.lst)
-
-# Combine all necessary flags and optional flags.
-# Add target processor to flags.
-ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS)
-ALL_CXXFLAGS = -mmcu=$(MCU) -I. $(CXXFLAGS)
-ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
-
-
-# Default target.
-all: build
-
-build: applet/$(TARGET).hex
-
-eep: applet/$(TARGET).eep
-lss: applet/$(TARGET).lss 
-sym: applet/$(TARGET).sym
-
-
-# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
-COFFCONVERT=$(OBJCOPY) --debugging \
---change-section-address .data-0x800000 \
---change-section-address .bss-0x800000 \
---change-section-address .noinit-0x800000 \
---change-section-address .eeprom-0x810000 
-
-
-coff: applet/$(TARGET).elf
-	$(COFFCONVERT) -O coff-avr applet/$(TARGET).elf applet/$(TARGET).cof
-
-
-extcoff: applet/$(TARGET).elf
-	$(COFFCONVERT) -O coff-ext-avr applet/$(TARGET).elf applet/$(TARGET).cof
-
-
-.SUFFIXES: .elf .hex .eep .lss .sym .pde
-
-.elf.hex:
-	$(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@
-
-.elf.eep:
-	-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
-	--change-section-lma .eeprom=0 -O $(FORMAT) $< $@
-
-# Create extended listing file from ELF output file.
-.elf.lss:
-	$(OBJDUMP) -h -S $< > $@
-
-# Create a symbol table from ELF output file.
-.elf.sym:
-	$(NM) -n $< > $@
-
-
-# Compile: create object files from C++ source files.
-.cpp.o: $(HEADERS)
-	$(CXX) -c $(ALL_CXXFLAGS) $< -o $@ 
-
-# Compile: create object files from C source files.
-.c.o: $(HEADERS)
-	$(CC)  -c $(ALL_CFLAGS) $< -o $@ 
-
-
-# Compile: create assembler files from C source files.
-.c.s:
-	$(CC) -S $(ALL_CFLAGS) $< -o $@
-
-
-# Assemble: create object files from assembler source files.
-.S.o:
-	$(CC) -c $(ALL_ASFLAGS) $< -o $@
-
-
-
-applet/$(TARGET).cpp: $(TARGET).pde
-	test -d applet || mkdir applet
-	echo '#include "WProgram.h"' > applet/$(TARGET).cpp
-	echo '#include "avr/interrupt.h"' >> applet/$(TARGET).cpp
-	sed -n 's|^\(void .*)\).*|\1;|p' $(TARGET).pde | grep -v 'setup()' | \
-		grep -v 'loop()' >> applet/$(TARGET).cpp
-	cat $(TARGET).pde >> applet/$(TARGET).cpp
-	cat $(ARDUINO_SRC)/main.cxx >> applet/$(TARGET).cpp
-
-# Link: create ELF output file from object files.
-applet/$(TARGET).elf: applet/$(TARGET).cpp $(OBJ)
-	$(CC) $(ALL_CFLAGS) $(OBJ) --output $@ $(LDFLAGS)
-
-pd_close_serial:
-	echo 'close;' | /Applications/Pd-extended.app/Contents/Resources/bin/pdsend 34567 || true
-
-# Program the device.  
-upload: applet/$(TARGET).hex
-	$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH)
-
-
-pd_test: build pd_close_serial upload
-
-# Target: clean project.
-clean:
-	$(REMOVE) -- applet/$(TARGET).hex applet/$(TARGET).eep \
-	applet/$(TARGET).cof applet/$(TARGET).elf $(TARGET).map \
-	applet/$(TARGET).sym applet/$(TARGET).lss applet/$(TARGET).cpp \
-	$(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d)
-	rmdir -- applet
-
-depend:
-	if grep '^# DO NOT DELETE' $(MAKEFILE) >/dev/null; \
-	then \
-		sed -e '/^# DO NOT DELETE/,$$d' $(MAKEFILE) > \
-			$(MAKEFILE).$$$$ && \
-		$(MV) $(MAKEFILE).$$$$ $(MAKEFILE); \
-	fi
-	echo '# DO NOT DELETE THIS LINE -- make depend depends on it.' \
-		>> $(MAKEFILE); \
-	$(CC) -M -mmcu=$(MCU) $(CDEFS) $(INCLUDE) $(SRC) $(ASRC) >> $(MAKEFILE)
-
-.PHONY:	all build eep lss sym coff extcoff clean depend pd_close_serial pd_test
-
-# for emacs
-etags:
-	make etags_`uname -s`
-	etags *.pde \
-		$(ARDUINO_SRC)/*.[ch] \
-		$(ARDUINO_SRC)/*.cpp \
-		$(ARDUINO_LIB_SRC)/*/*.[ch] \
-		$(ARDUINO_LIB_SRC)/*/*.cpp \
-		$(ARDUINO)/hardware/tools/avr/avr/include/avr/*.[ch] \
-		$(ARDUINO)/hardware/tools/avr/avr/include/*.[ch]
-
-etags_Darwin:
-#	etags -a 
-
-etags_Linux:
-#	etags -a /usr/include/*.h linux/input.h /usr/include/sys/*.h
-
-etags_MINGW:
-#	etags -a /usr/include/*.h /usr/include/sys/*.h 
-
-
-
diff --git a/libraries/Firmata/examples/EchoString/EchoString.pde b/libraries/Firmata/examples/EchoString/EchoString.pde
deleted file mode 100644
index 6559ae1..0000000
--- a/libraries/Firmata/examples/EchoString/EchoString.pde
+++ /dev/null
@@ -1,40 +0,0 @@
-/* This sketch accepts strings and raw sysex messages and echos them back.
- *
- * This example code is in the public domain.
- */
-#include <Firmata.h>
-
-byte analogPin;
-
-void stringCallback(char *myString)
-{
-    Firmata.sendString(myString);
-}
-
-
-void sysexCallback(byte command, byte argc, byte*argv)
-{
-    Serial.print(START_SYSEX, BYTE);
-    Serial.print(command, BYTE);
-    for(byte i=0; i<argc; i++) {
-        Serial.print(argv[i], BYTE);
-    }
-    Serial.print(END_SYSEX, BYTE);
-}
-
-void setup()
-{
-    Firmata.setFirmwareVersion(0, 1);
-    Firmata.attach(STRING_DATA, stringCallback);
-    Firmata.attach(START_SYSEX, sysexCallback);
-    Firmata.begin(57600);
-}
-
-void loop()
-{
-    while(Firmata.available()) {
-        Firmata.processInput();
-    }
-}
-
-
diff --git a/libraries/Firmata/examples/EchoString/Makefile b/libraries/Firmata/examples/EchoString/Makefile
deleted file mode 100644
index e968c0a..0000000
--- a/libraries/Firmata/examples/EchoString/Makefile
+++ /dev/null
@@ -1,263 +0,0 @@
-# Arduino makefile
-#
-# This makefile allows you to build sketches from the command line
-# without the Arduino environment (or Java).
-#
-# The Arduino environment does preliminary processing on a sketch before
-# compiling it.  If you're using this makefile instead, you'll need to do
-# a few things differently:
-#
-#   - Give your program's file a .cpp extension (e.g. foo.cpp).
-#
-#   - Put this line at top of your code: #include <WProgram.h>
-#
-#   - Write prototypes for all your functions (or define them before you
-#     call them).  A prototype declares the types of parameters a
-#     function will take and what type of value it will return.  This
-#     means that you can have a call to a function before the definition
-#     of the function.  A function prototype looks like the first line of
-#     the function, with a semi-colon at the end.  For example:
-#     int digitalRead(int pin);
-#
-# Instructions for using the makefile:
-#
-#  1. Copy this file into the folder with your sketch.
-#
-#  2. Below, modify the line containing "TARGET" to refer to the name of
-#     of your program's file without an extension (e.g. TARGET = foo).
-#
-#  3. Modify the line containg "ARDUINO" to point the directory that
-#     contains the Arduino core (for normal Arduino installations, this
-#     is the hardware/cores/arduino sub-directory).
-#
-#  4. Modify the line containing "PORT" to refer to the filename
-#     representing the USB or serial connection to your Arduino board
-#     (e.g. PORT = /dev/tty.USB0).  If the exact name of this file
-#     changes, you can use * as a wildcard (e.g. PORT = /dev/tty.USB*).
-#
-#  5. At the command line, change to the directory containing your
-#     program's file and the makefile.
-#
-#  6. Type "make" and press enter to compile/verify your program.
-#
-#  7. Type "make upload", reset your Arduino board, and press enter  to
-#     upload your program to the Arduino board.
-#
-# $Id: Makefile,v 1.7 2007/04/13 05:28:23 eighthave Exp $
-
-PORT = /dev/tty.usbserial-*
-TARGET := $(shell pwd | sed 's|.*/\(.*\)|\1|')
-ARDUINO = /Applications/arduino
-ARDUINO_SRC = $(ARDUINO)/hardware/cores/arduino
-ARDUINO_LIB_SRC = $(ARDUINO)/hardware/libraries
-INCLUDE = -I$(ARDUINO_SRC) -I$(ARDUINO)/hardware/tools/avr/avr/include \
-	-I$(ARDUINO_LIB_SRC)/EEPROM \
-	-I$(ARDUINO_LIB_SRC)/Firmata \
-	-I$(ARDUINO_LIB_SRC)/Servo \
-	-I$(ARDUINO_LIB_SRC)
-SRC = $(wildcard $(ARDUINO_SRC)/*.c)
-CXXSRC = applet/$(TARGET).cpp $(ARDUINO_SRC)/HardwareSerial.cpp \
-	$(ARDUINO_LIB_SRC)/EEPROM/EEPROM.cpp \
-	$(ARDUINO_LIB_SRC)/Firmata/Firmata.cpp \
-	$(ARDUINO_LIB_SRC)/Servo/Servo.cpp \
-	$(ARDUINO_SRC)/WMath.cpp
-HEADERS = $(wildcard $(ARDUINO_SRC)/*.h) $(wildcard $(ARDUINO_LIB_SRC)/*/*.h)
-
-MCU = atmega168
-#MCU = atmega8
-F_CPU = 16000000
-FORMAT = ihex
-UPLOAD_RATE = 19200
-
-# Name of this Makefile (used for "make depend").
-MAKEFILE = Makefile
-
-# Debugging format.
-# Native formats for AVR-GCC's -g are stabs [default], or dwarf-2.
-# AVR (extended) COFF requires stabs, plus an avr-objcopy run.
-DEBUG = stabs
-
-OPT = s
-
-# Place -D or -U options here
-CDEFS = -DF_CPU=$(F_CPU)
-CXXDEFS = -DF_CPU=$(F_CPU)
-
-# Compiler flag to set the C Standard level.
-# c89   - "ANSI" C
-# gnu89 - c89 plus GCC extensions
-# c99   - ISO C99 standard (not yet fully implemented)
-# gnu99 - c99 plus GCC extensions
-CSTANDARD = -std=gnu99
-CDEBUG = -g$(DEBUG)
-CWARN = -Wall -Wstrict-prototypes
-CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums
-#CEXTRA = -Wa,-adhlns=$(<:.c=.lst)
-
-CFLAGS = $(CDEBUG) $(CDEFS) $(INCLUDE) -O$(OPT) $(CWARN) $(CSTANDARD) $(CEXTRA)
-CXXFLAGS = $(CDEFS) $(INCLUDE) -O$(OPT)
-#ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs 
-LDFLAGS = 
-
-
-# Programming support using avrdude. Settings and variables.
-AVRDUDE_PROGRAMMER = stk500
-AVRDUDE_PORT = $(PORT)
-AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex
-AVRDUDE_FLAGS = -F -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) \
-  -b $(UPLOAD_RATE) -q -V
-
-# Program settings
-CC = avr-gcc
-CXX = avr-g++
-OBJCOPY = avr-objcopy
-OBJDUMP = avr-objdump
-SIZE = avr-size
-NM = avr-nm
-AVRDUDE = avrdude
-REMOVE = rm -f
-MV = mv -f
-
-# Define all object files.
-OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o)
-
-# Define all listing files.
-LST = $(ASRC:.S=.lst) $(CXXSRC:.cpp=.lst) $(SRC:.c=.lst)
-
-# Combine all necessary flags and optional flags.
-# Add target processor to flags.
-ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS)
-ALL_CXXFLAGS = -mmcu=$(MCU) -I. $(CXXFLAGS)
-ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
-
-
-# Default target.
-all: build
-
-build: applet/$(TARGET).hex
-
-eep: applet/$(TARGET).eep
-lss: applet/$(TARGET).lss 
-sym: applet/$(TARGET).sym
-
-
-# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
-COFFCONVERT=$(OBJCOPY) --debugging \
---change-section-address .data-0x800000 \
---change-section-address .bss-0x800000 \
---change-section-address .noinit-0x800000 \
---change-section-address .eeprom-0x810000 
-
-
-coff: applet/$(TARGET).elf
-	$(COFFCONVERT) -O coff-avr applet/$(TARGET).elf applet/$(TARGET).cof
-
-
-extcoff: applet/$(TARGET).elf
-	$(COFFCONVERT) -O coff-ext-avr applet/$(TARGET).elf applet/$(TARGET).cof
-
-
-.SUFFIXES: .elf .hex .eep .lss .sym .pde
-
-.elf.hex:
-	$(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@
-
-.elf.eep:
-	-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
-	--change-section-lma .eeprom=0 -O $(FORMAT) $< $@
-
-# Create extended listing file from ELF output file.
-.elf.lss:
-	$(OBJDUMP) -h -S $< > $@
-
-# Create a symbol table from ELF output file.
-.elf.sym:
-	$(NM) -n $< > $@
-
-
-# Compile: create object files from C++ source files.
-.cpp.o: $(HEADERS)
-	$(CXX) -c $(ALL_CXXFLAGS) $< -o $@ 
-
-# Compile: create object files from C source files.
-.c.o: $(HEADERS)
-	$(CC)  -c $(ALL_CFLAGS) $< -o $@ 
-
-
-# Compile: create assembler files from C source files.
-.c.s:
-	$(CC) -S $(ALL_CFLAGS) $< -o $@
-
-
-# Assemble: create object files from assembler source files.
-.S.o:
-	$(CC) -c $(ALL_ASFLAGS) $< -o $@
-
-
-
-applet/$(TARGET).cpp: $(TARGET).pde
-	test -d applet || mkdir applet
-	echo '#include "WProgram.h"' > applet/$(TARGET).cpp
-	echo '#include "avr/interrupt.h"' >> applet/$(TARGET).cpp
-	sed -n 's|^\(void .*)\).*|\1;|p' $(TARGET).pde | grep -v 'setup()' | \
-		grep -v 'loop()' >> applet/$(TARGET).cpp
-	cat $(TARGET).pde >> applet/$(TARGET).cpp
-	cat $(ARDUINO_SRC)/main.cxx >> applet/$(TARGET).cpp
-
-# Link: create ELF output file from object files.
-applet/$(TARGET).elf: applet/$(TARGET).cpp $(OBJ)
-	$(CC) $(ALL_CFLAGS) $(OBJ) --output $@ $(LDFLAGS)
-
-pd_close_serial:
-	echo 'close;' | /Applications/Pd-extended.app/Contents/Resources/bin/pdsend 34567 || true
-
-# Program the device.  
-upload: applet/$(TARGET).hex
-	$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH)
-
-
-pd_test: build pd_close_serial upload
-
-# Target: clean project.
-clean:
-	$(REMOVE) -- applet/$(TARGET).hex applet/$(TARGET).eep \
-	applet/$(TARGET).cof applet/$(TARGET).elf $(TARGET).map \
-	applet/$(TARGET).sym applet/$(TARGET).lss applet/$(TARGET).cpp \
-	$(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d)
-	rmdir -- applet
-
-depend:
-	if grep '^# DO NOT DELETE' $(MAKEFILE) >/dev/null; \
-	then \
-		sed -e '/^# DO NOT DELETE/,$$d' $(MAKEFILE) > \
-			$(MAKEFILE).$$$$ && \
-		$(MV) $(MAKEFILE).$$$$ $(MAKEFILE); \
-	fi
-	echo '# DO NOT DELETE THIS LINE -- make depend depends on it.' \
-		>> $(MAKEFILE); \
-	$(CC) -M -mmcu=$(MCU) $(CDEFS) $(INCLUDE) $(SRC) $(ASRC) >> $(MAKEFILE)
-
-.PHONY:	all build eep lss sym coff extcoff clean depend pd_close_serial pd_test
-
-# for emacs
-etags:
-	make etags_`uname -s`
-	etags *.pde \
-		$(ARDUINO_SRC)/*.[ch] \
-		$(ARDUINO_SRC)/*.cpp \
-		$(ARDUINO_LIB_SRC)/*/*.[ch] \
-		$(ARDUINO_LIB_SRC)/*/*.cpp \
-		$(ARDUINO)/hardware/tools/avr/avr/include/avr/*.[ch] \
-		$(ARDUINO)/hardware/tools/avr/avr/include/*.[ch]
-
-etags_Darwin:
-#	etags -a 
-
-etags_Linux:
-#	etags -a /usr/include/*.h linux/input.h /usr/include/sys/*.h
-
-etags_MINGW:
-#	etags -a /usr/include/*.h /usr/include/sys/*.h 
-
-
-
diff --git a/libraries/Firmata/examples/I2CFirmata/I2CFirmata.pde b/libraries/Firmata/examples/I2CFirmata/I2CFirmata.pde
deleted file mode 100644
index 796a8d5..0000000
--- a/libraries/Firmata/examples/I2CFirmata/I2CFirmata.pde
+++ /dev/null
@@ -1,217 +0,0 @@
-/*
- Copyright (C) 2009 Jeff Hoefs.  All rights reserved.
- Copyright (C) 2009 Shigeru Kobayashi.  All rights reserved.
- 
- This library is free software; you can redistribute it and/or
- modify it under the terms of the GNU Lesser General Public
- License as published by the Free Software Foundation; either
- version 2.1 of the License, or (at your option) any later version.
- 
- See file LICENSE.txt for further informations on licensing terms.
- */
-
-#include <Wire.h>
-#include <Firmata.h>
-
-
-#define I2C_WRITE B00000000
-#define I2C_READ B00001000
-#define I2C_READ_CONTINUOUSLY B00010000
-#define I2C_STOP_READING B00011000
-#define I2C_READ_WRITE_MODE_MASK B00011000
-
-#define MAX_QUERIES 8
-
-unsigned long currentMillis;     // store the current value from millis()
-unsigned long nextExecuteMillis; // for comparison with currentMillis
-unsigned int samplingInterval = 32;  // default sampling interval is 33ms
-unsigned int i2cReadDelayTime = 0;  // default delay time between i2c read request and Wire.requestFrom()
-unsigned int powerPinsEnabled = 0;  // use as boolean to prevent enablePowerPins from being called more than once
-
-#define MINIMUM_SAMPLING_INTERVAL 10
-
-#define REGISTER_NOT_SPECIFIED -1
-
-struct i2c_device_info {
-  byte addr;
-  byte reg;
-  byte bytes;
-};
-
-i2c_device_info query[MAX_QUERIES];
-
-byte i2cRxData[32];
-boolean readingContinuously = false;
-byte queryIndex = 0;
-
-void readAndReportData(byte address, int theRegister, byte numBytes)
-{
-  if (theRegister != REGISTER_NOT_SPECIFIED) {
-    Wire.beginTransmission(address);
-    Wire.send((byte)theRegister);
-    Wire.endTransmission();
-    delayMicroseconds(i2cReadDelayTime);  // delay is necessary for some devices such as WiiNunchuck
-  } 
-  else {
-    theRegister = 0;  // fill the register with a dummy value
-  }
-
-  Wire.requestFrom(address, numBytes);
-
-  // check to be sure correct number of bytes were returned by slave
-  if(numBytes == Wire.available()) {
-    i2cRxData[0] = address;
-    i2cRxData[1] = theRegister;
-    for (int i = 0; i < numBytes; i++) {
-      i2cRxData[2 + i] = Wire.receive();
-    }
-    // send slave address, register and received bytes
-    Firmata.sendSysex(I2C_REPLY, numBytes + 2, i2cRxData);
-  }
-  else {
-    if(numBytes > Wire.available()) {
-      Firmata.sendString("I2C Read Error: Too many bytes received");
-    } else {
-      Firmata.sendString("I2C Read Error: Too few bytes received"); 
-    }
-  }
-  
-}
-
-void sysexCallback(byte command, byte argc, byte *argv)
-{
-  byte mode;
-  byte slaveAddress;
-  byte slaveRegister;
-  byte data;
-  int  delayTime;
-
-  if (command == I2C_REQUEST) {
-    mode = argv[1] & I2C_READ_WRITE_MODE_MASK;
-    slaveAddress = argv[0];
-
-    switch(mode) {
-    case I2C_WRITE:
-      Wire.beginTransmission(slaveAddress);
-      for (byte i = 2; i < argc; i += 2) {
-        data = argv[i] + (argv[i + 1] << 7);
-        Wire.send(data);
-      }
-      Wire.endTransmission();
-      delayMicroseconds(70); // TODO is this needed?
-      break;
-    case I2C_READ:
-      if (argc == 6) {
-        // a slave register is specified
-        slaveRegister = argv[2] + (argv[3] << 7);
-        data = argv[4] + (argv[5] << 7);  // bytes to read
-        readAndReportData(slaveAddress, (int)slaveRegister, data);
-      } 
-      else {
-        // a slave register is NOT specified
-        data = argv[2] + (argv[3] << 7);  // bytes to read
-        readAndReportData(slaveAddress, (int)REGISTER_NOT_SPECIFIED, data);
-      }
-      break;
-    case I2C_READ_CONTINUOUSLY:
-      if ((queryIndex + 1) >= MAX_QUERIES) {
-        // too many queries, just ignore
-        Firmata.sendString("too many queries");
-        break;
-      }
-      query[queryIndex].addr = slaveAddress;
-      query[queryIndex].reg = argv[2] + (argv[3] << 7);
-      query[queryIndex].bytes = argv[4] + (argv[5] << 7);
-      readingContinuously = true;
-      queryIndex++;
-      break;
-    case I2C_STOP_READING:
-      readingContinuously = false;
-      queryIndex = 0;
-      break;
-    default:
-      break;
-    }
-  }
-  else if (command == SAMPLING_INTERVAL) {
-    samplingInterval = argv[0] + (argv[1] << 7);
-
-    if (samplingInterval < MINIMUM_SAMPLING_INTERVAL) {
-      samplingInterval = MINIMUM_SAMPLING_INTERVAL;
-    }
-
-    samplingInterval -= 1;
-    Firmata.sendString("sampling interval");
-  }
-
-  else if (command == I2C_CONFIG) {
-    delayTime = (argv[4] + (argv[5] << 7));                        // MSB
-    delayTime = (delayTime << 8) + (argv[2] + (argv[3] << 7));     // add LSB
-
-    if((argv[0] + (argv[1] << 7)) > 0) {
-      enablePowerPins(PORTC3, PORTC2);
-    }
-
-    if(delayTime > 0) {
-      i2cReadDelayTime = delayTime;
-    }
-
-    if(argc > 6) {
-      // If you extend I2C_Config, handle your data here
-    }
-
-  }
-}
-
-void systemResetCallback()
-{
-  readingContinuously = false;
-  queryIndex = 0;
-}
-
-/* reference: BlinkM_funcs.h by Tod E. Kurt, ThingM, http://thingm.com/ */
-// Enables Pins A2 and A3 to be used as GND and Power
-// so that I2C devices can be plugged directly
-// into Arduino header (pins A2 - A5)
-static void enablePowerPins(byte pwrpin, byte gndpin)
-{
-  if(powerPinsEnabled == 0) {
-    DDRC |= _BV(pwrpin) | _BV(gndpin);
-    PORTC &=~ _BV(gndpin);
-    PORTC |=  _BV(pwrpin);
-    powerPinsEnabled = 1;
-    Firmata.sendString("Power pins enabled");
-    delay(100);
-  }
-}
-
-void setup()
-{
-  Firmata.setFirmwareVersion(2, 0);
-
-  Firmata.attach(START_SYSEX, sysexCallback);
-  Firmata.attach(SYSTEM_RESET, systemResetCallback);
-
-  for (int i = 0; i < TOTAL_DIGITAL_PINS; ++i) {
-    pinMode(i, OUTPUT);
-  }
-
-  Firmata.begin(57600);  
-  Wire.begin();
-}
-
-void loop()
-{
-  while (Firmata.available()) {
-    Firmata.processInput();
-  }
-
-  currentMillis = millis();
-  if (currentMillis > nextExecuteMillis) {
-    nextExecuteMillis = currentMillis + samplingInterval;
-
-    for (byte i = 0; i < queryIndex; i++) {
-      readAndReportData(query[i].addr, query[i].reg, query[i].bytes);
-    }
-  }
-}
diff --git a/libraries/Firmata/examples/ServoFirmata/Makefile b/libraries/Firmata/examples/ServoFirmata/Makefile
deleted file mode 100644
index e968c0a..0000000
--- a/libraries/Firmata/examples/ServoFirmata/Makefile
+++ /dev/null
@@ -1,263 +0,0 @@
-# Arduino makefile
-#
-# This makefile allows you to build sketches from the command line
-# without the Arduino environment (or Java).
-#
-# The Arduino environment does preliminary processing on a sketch before
-# compiling it.  If you're using this makefile instead, you'll need to do
-# a few things differently:
-#
-#   - Give your program's file a .cpp extension (e.g. foo.cpp).
-#
-#   - Put this line at top of your code: #include <WProgram.h>
-#
-#   - Write prototypes for all your functions (or define them before you
-#     call them).  A prototype declares the types of parameters a
-#     function will take and what type of value it will return.  This
-#     means that you can have a call to a function before the definition
-#     of the function.  A function prototype looks like the first line of
-#     the function, with a semi-colon at the end.  For example:
-#     int digitalRead(int pin);
-#
-# Instructions for using the makefile:
-#
-#  1. Copy this file into the folder with your sketch.
-#
-#  2. Below, modify the line containing "TARGET" to refer to the name of
-#     of your program's file without an extension (e.g. TARGET = foo).
-#
-#  3. Modify the line containg "ARDUINO" to point the directory that
-#     contains the Arduino core (for normal Arduino installations, this
-#     is the hardware/cores/arduino sub-directory).
-#
-#  4. Modify the line containing "PORT" to refer to the filename
-#     representing the USB or serial connection to your Arduino board
-#     (e.g. PORT = /dev/tty.USB0).  If the exact name of this file
-#     changes, you can use * as a wildcard (e.g. PORT = /dev/tty.USB*).
-#
-#  5. At the command line, change to the directory containing your
-#     program's file and the makefile.
-#
-#  6. Type "make" and press enter to compile/verify your program.
-#
-#  7. Type "make upload", reset your Arduino board, and press enter  to
-#     upload your program to the Arduino board.
-#
-# $Id: Makefile,v 1.7 2007/04/13 05:28:23 eighthave Exp $
-
-PORT = /dev/tty.usbserial-*
-TARGET := $(shell pwd | sed 's|.*/\(.*\)|\1|')
-ARDUINO = /Applications/arduino
-ARDUINO_SRC = $(ARDUINO)/hardware/cores/arduino
-ARDUINO_LIB_SRC = $(ARDUINO)/hardware/libraries
-INCLUDE = -I$(ARDUINO_SRC) -I$(ARDUINO)/hardware/tools/avr/avr/include \
-	-I$(ARDUINO_LIB_SRC)/EEPROM \
-	-I$(ARDUINO_LIB_SRC)/Firmata \
-	-I$(ARDUINO_LIB_SRC)/Servo \
-	-I$(ARDUINO_LIB_SRC)
-SRC = $(wildcard $(ARDUINO_SRC)/*.c)
-CXXSRC = applet/$(TARGET).cpp $(ARDUINO_SRC)/HardwareSerial.cpp \
-	$(ARDUINO_LIB_SRC)/EEPROM/EEPROM.cpp \
-	$(ARDUINO_LIB_SRC)/Firmata/Firmata.cpp \
-	$(ARDUINO_LIB_SRC)/Servo/Servo.cpp \
-	$(ARDUINO_SRC)/WMath.cpp
-HEADERS = $(wildcard $(ARDUINO_SRC)/*.h) $(wildcard $(ARDUINO_LIB_SRC)/*/*.h)
-
-MCU = atmega168
-#MCU = atmega8
-F_CPU = 16000000
-FORMAT = ihex
-UPLOAD_RATE = 19200
-
-# Name of this Makefile (used for "make depend").
-MAKEFILE = Makefile
-
-# Debugging format.
-# Native formats for AVR-GCC's -g are stabs [default], or dwarf-2.
-# AVR (extended) COFF requires stabs, plus an avr-objcopy run.
-DEBUG = stabs
-
-OPT = s
-
-# Place -D or -U options here
-CDEFS = -DF_CPU=$(F_CPU)
-CXXDEFS = -DF_CPU=$(F_CPU)
-
-# Compiler flag to set the C Standard level.
-# c89   - "ANSI" C
-# gnu89 - c89 plus GCC extensions
-# c99   - ISO C99 standard (not yet fully implemented)
-# gnu99 - c99 plus GCC extensions
-CSTANDARD = -std=gnu99
-CDEBUG = -g$(DEBUG)
-CWARN = -Wall -Wstrict-prototypes
-CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums
-#CEXTRA = -Wa,-adhlns=$(<:.c=.lst)
-
-CFLAGS = $(CDEBUG) $(CDEFS) $(INCLUDE) -O$(OPT) $(CWARN) $(CSTANDARD) $(CEXTRA)
-CXXFLAGS = $(CDEFS) $(INCLUDE) -O$(OPT)
-#ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs 
-LDFLAGS = 
-
-
-# Programming support using avrdude. Settings and variables.
-AVRDUDE_PROGRAMMER = stk500
-AVRDUDE_PORT = $(PORT)
-AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex
-AVRDUDE_FLAGS = -F -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) \
-  -b $(UPLOAD_RATE) -q -V
-
-# Program settings
-CC = avr-gcc
-CXX = avr-g++
-OBJCOPY = avr-objcopy
-OBJDUMP = avr-objdump
-SIZE = avr-size
-NM = avr-nm
-AVRDUDE = avrdude
-REMOVE = rm -f
-MV = mv -f
-
-# Define all object files.
-OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o)
-
-# Define all listing files.
-LST = $(ASRC:.S=.lst) $(CXXSRC:.cpp=.lst) $(SRC:.c=.lst)
-
-# Combine all necessary flags and optional flags.
-# Add target processor to flags.
-ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS)
-ALL_CXXFLAGS = -mmcu=$(MCU) -I. $(CXXFLAGS)
-ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
-
-
-# Default target.
-all: build
-
-build: applet/$(TARGET).hex
-
-eep: applet/$(TARGET).eep
-lss: applet/$(TARGET).lss 
-sym: applet/$(TARGET).sym
-
-
-# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
-COFFCONVERT=$(OBJCOPY) --debugging \
---change-section-address .data-0x800000 \
---change-section-address .bss-0x800000 \
---change-section-address .noinit-0x800000 \
---change-section-address .eeprom-0x810000 
-
-
-coff: applet/$(TARGET).elf
-	$(COFFCONVERT) -O coff-avr applet/$(TARGET).elf applet/$(TARGET).cof
-
-
-extcoff: applet/$(TARGET).elf
-	$(COFFCONVERT) -O coff-ext-avr applet/$(TARGET).elf applet/$(TARGET).cof
-
-
-.SUFFIXES: .elf .hex .eep .lss .sym .pde
-
-.elf.hex:
-	$(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@
-
-.elf.eep:
-	-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
-	--change-section-lma .eeprom=0 -O $(FORMAT) $< $@
-
-# Create extended listing file from ELF output file.
-.elf.lss:
-	$(OBJDUMP) -h -S $< > $@
-
-# Create a symbol table from ELF output file.
-.elf.sym:
-	$(NM) -n $< > $@
-
-
-# Compile: create object files from C++ source files.
-.cpp.o: $(HEADERS)
-	$(CXX) -c $(ALL_CXXFLAGS) $< -o $@ 
-
-# Compile: create object files from C source files.
-.c.o: $(HEADERS)
-	$(CC)  -c $(ALL_CFLAGS) $< -o $@ 
-
-
-# Compile: create assembler files from C source files.
-.c.s:
-	$(CC) -S $(ALL_CFLAGS) $< -o $@
-
-
-# Assemble: create object files from assembler source files.
-.S.o:
-	$(CC) -c $(ALL_ASFLAGS) $< -o $@
-
-
-
-applet/$(TARGET).cpp: $(TARGET).pde
-	test -d applet || mkdir applet
-	echo '#include "WProgram.h"' > applet/$(TARGET).cpp
-	echo '#include "avr/interrupt.h"' >> applet/$(TARGET).cpp
-	sed -n 's|^\(void .*)\).*|\1;|p' $(TARGET).pde | grep -v 'setup()' | \
-		grep -v 'loop()' >> applet/$(TARGET).cpp
-	cat $(TARGET).pde >> applet/$(TARGET).cpp
-	cat $(ARDUINO_SRC)/main.cxx >> applet/$(TARGET).cpp
-
-# Link: create ELF output file from object files.
-applet/$(TARGET).elf: applet/$(TARGET).cpp $(OBJ)
-	$(CC) $(ALL_CFLAGS) $(OBJ) --output $@ $(LDFLAGS)
-
-pd_close_serial:
-	echo 'close;' | /Applications/Pd-extended.app/Contents/Resources/bin/pdsend 34567 || true
-
-# Program the device.  
-upload: applet/$(TARGET).hex
-	$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH)
-
-
-pd_test: build pd_close_serial upload
-
-# Target: clean project.
-clean:
-	$(REMOVE) -- applet/$(TARGET).hex applet/$(TARGET).eep \
-	applet/$(TARGET).cof applet/$(TARGET).elf $(TARGET).map \
-	applet/$(TARGET).sym applet/$(TARGET).lss applet/$(TARGET).cpp \
-	$(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d)
-	rmdir -- applet
-
-depend:
-	if grep '^# DO NOT DELETE' $(MAKEFILE) >/dev/null; \
-	then \
-		sed -e '/^# DO NOT DELETE/,$$d' $(MAKEFILE) > \
-			$(MAKEFILE).$$$$ && \
-		$(MV) $(MAKEFILE).$$$$ $(MAKEFILE); \
-	fi
-	echo '# DO NOT DELETE THIS LINE -- make depend depends on it.' \
-		>> $(MAKEFILE); \
-	$(CC) -M -mmcu=$(MCU) $(CDEFS) $(INCLUDE) $(SRC) $(ASRC) >> $(MAKEFILE)
-
-.PHONY:	all build eep lss sym coff extcoff clean depend pd_close_serial pd_test
-
-# for emacs
-etags:
-	make etags_`uname -s`
-	etags *.pde \
-		$(ARDUINO_SRC)/*.[ch] \
-		$(ARDUINO_SRC)/*.cpp \
-		$(ARDUINO_LIB_SRC)/*/*.[ch] \
-		$(ARDUINO_LIB_SRC)/*/*.cpp \
-		$(ARDUINO)/hardware/tools/avr/avr/include/avr/*.[ch] \
-		$(ARDUINO)/hardware/tools/avr/avr/include/*.[ch]
-
-etags_Darwin:
-#	etags -a 
-
-etags_Linux:
-#	etags -a /usr/include/*.h linux/input.h /usr/include/sys/*.h
-
-etags_MINGW:
-#	etags -a /usr/include/*.h /usr/include/sys/*.h 
-
-
-
diff --git a/libraries/Firmata/examples/ServoFirmata/ServoFirmata.pde b/libraries/Firmata/examples/ServoFirmata/ServoFirmata.pde
deleted file mode 100644
index fa48e2b..0000000
--- a/libraries/Firmata/examples/ServoFirmata/ServoFirmata.pde
+++ /dev/null
@@ -1,39 +0,0 @@
-/* This firmware supports as many servos as possible using the Servo" library 
- * included in Arduino 0012
- *
- * TODO add message to configure minPulse/maxPulse/degrees
- *
- * This example code is in the public domain.
- */
- 
-#include <Firmata.h>
-#include <Servo.h>
-
-Servo servo9;
-Servo servo10;
-
-void analogWriteCallback(byte pin, int value)
-{
-    if(pin == 9)
-      servo9.write(value);
-    if(pin == 10)
-      servo10.write(value);
-}
-
-void setup() 
-{
-    Firmata.setFirmwareVersion(0, 2);
-    Firmata.attach(ANALOG_MESSAGE, analogWriteCallback);
-
-    servo9.attach(9);
-    servo10.attach(10);
-   
-    Firmata.begin(57600);
-}
-
-void loop() 
-{
-    while(Firmata.available())
-        Firmata.processInput();
-}
-
diff --git a/libraries/Firmata/examples/SimpleAnalogFirmata/Makefile b/libraries/Firmata/examples/SimpleAnalogFirmata/Makefile
deleted file mode 100644
index e968c0a..0000000
--- a/libraries/Firmata/examples/SimpleAnalogFirmata/Makefile
+++ /dev/null
@@ -1,263 +0,0 @@
-# Arduino makefile
-#
-# This makefile allows you to build sketches from the command line
-# without the Arduino environment (or Java).
-#
-# The Arduino environment does preliminary processing on a sketch before
-# compiling it.  If you're using this makefile instead, you'll need to do
-# a few things differently:
-#
-#   - Give your program's file a .cpp extension (e.g. foo.cpp).
-#
-#   - Put this line at top of your code: #include <WProgram.h>
-#
-#   - Write prototypes for all your functions (or define them before you
-#     call them).  A prototype declares the types of parameters a
-#     function will take and what type of value it will return.  This
-#     means that you can have a call to a function before the definition
-#     of the function.  A function prototype looks like the first line of
-#     the function, with a semi-colon at the end.  For example:
-#     int digitalRead(int pin);
-#
-# Instructions for using the makefile:
-#
-#  1. Copy this file into the folder with your sketch.
-#
-#  2. Below, modify the line containing "TARGET" to refer to the name of
-#     of your program's file without an extension (e.g. TARGET = foo).
-#
-#  3. Modify the line containg "ARDUINO" to point the directory that
-#     contains the Arduino core (for normal Arduino installations, this
-#     is the hardware/cores/arduino sub-directory).
-#
-#  4. Modify the line containing "PORT" to refer to the filename
-#     representing the USB or serial connection to your Arduino board
-#     (e.g. PORT = /dev/tty.USB0).  If the exact name of this file
-#     changes, you can use * as a wildcard (e.g. PORT = /dev/tty.USB*).
-#
-#  5. At the command line, change to the directory containing your
-#     program's file and the makefile.
-#
-#  6. Type "make" and press enter to compile/verify your program.
-#
-#  7. Type "make upload", reset your Arduino board, and press enter  to
-#     upload your program to the Arduino board.
-#
-# $Id: Makefile,v 1.7 2007/04/13 05:28:23 eighthave Exp $
-
-PORT = /dev/tty.usbserial-*
-TARGET := $(shell pwd | sed 's|.*/\(.*\)|\1|')
-ARDUINO = /Applications/arduino
-ARDUINO_SRC = $(ARDUINO)/hardware/cores/arduino
-ARDUINO_LIB_SRC = $(ARDUINO)/hardware/libraries
-INCLUDE = -I$(ARDUINO_SRC) -I$(ARDUINO)/hardware/tools/avr/avr/include \
-	-I$(ARDUINO_LIB_SRC)/EEPROM \
-	-I$(ARDUINO_LIB_SRC)/Firmata \
-	-I$(ARDUINO_LIB_SRC)/Servo \
-	-I$(ARDUINO_LIB_SRC)
-SRC = $(wildcard $(ARDUINO_SRC)/*.c)
-CXXSRC = applet/$(TARGET).cpp $(ARDUINO_SRC)/HardwareSerial.cpp \
-	$(ARDUINO_LIB_SRC)/EEPROM/EEPROM.cpp \
-	$(ARDUINO_LIB_SRC)/Firmata/Firmata.cpp \
-	$(ARDUINO_LIB_SRC)/Servo/Servo.cpp \
-	$(ARDUINO_SRC)/WMath.cpp
-HEADERS = $(wildcard $(ARDUINO_SRC)/*.h) $(wildcard $(ARDUINO_LIB_SRC)/*/*.h)
-
-MCU = atmega168
-#MCU = atmega8
-F_CPU = 16000000
-FORMAT = ihex
-UPLOAD_RATE = 19200
-
-# Name of this Makefile (used for "make depend").
-MAKEFILE = Makefile
-
-# Debugging format.
-# Native formats for AVR-GCC's -g are stabs [default], or dwarf-2.
-# AVR (extended) COFF requires stabs, plus an avr-objcopy run.
-DEBUG = stabs
-
-OPT = s
-
-# Place -D or -U options here
-CDEFS = -DF_CPU=$(F_CPU)
-CXXDEFS = -DF_CPU=$(F_CPU)
-
-# Compiler flag to set the C Standard level.
-# c89   - "ANSI" C
-# gnu89 - c89 plus GCC extensions
-# c99   - ISO C99 standard (not yet fully implemented)
-# gnu99 - c99 plus GCC extensions
-CSTANDARD = -std=gnu99
-CDEBUG = -g$(DEBUG)
-CWARN = -Wall -Wstrict-prototypes
-CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums
-#CEXTRA = -Wa,-adhlns=$(<:.c=.lst)
-
-CFLAGS = $(CDEBUG) $(CDEFS) $(INCLUDE) -O$(OPT) $(CWARN) $(CSTANDARD) $(CEXTRA)
-CXXFLAGS = $(CDEFS) $(INCLUDE) -O$(OPT)
-#ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs 
-LDFLAGS = 
-
-
-# Programming support using avrdude. Settings and variables.
-AVRDUDE_PROGRAMMER = stk500
-AVRDUDE_PORT = $(PORT)
-AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex
-AVRDUDE_FLAGS = -F -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) \
-  -b $(UPLOAD_RATE) -q -V
-
-# Program settings
-CC = avr-gcc
-CXX = avr-g++
-OBJCOPY = avr-objcopy
-OBJDUMP = avr-objdump
-SIZE = avr-size
-NM = avr-nm
-AVRDUDE = avrdude
-REMOVE = rm -f
-MV = mv -f
-
-# Define all object files.
-OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o)
-
-# Define all listing files.
-LST = $(ASRC:.S=.lst) $(CXXSRC:.cpp=.lst) $(SRC:.c=.lst)
-
-# Combine all necessary flags and optional flags.
-# Add target processor to flags.
-ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS)
-ALL_CXXFLAGS = -mmcu=$(MCU) -I. $(CXXFLAGS)
-ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
-
-
-# Default target.
-all: build
-
-build: applet/$(TARGET).hex
-
-eep: applet/$(TARGET).eep
-lss: applet/$(TARGET).lss 
-sym: applet/$(TARGET).sym
-
-
-# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
-COFFCONVERT=$(OBJCOPY) --debugging \
---change-section-address .data-0x800000 \
---change-section-address .bss-0x800000 \
---change-section-address .noinit-0x800000 \
---change-section-address .eeprom-0x810000 
-
-
-coff: applet/$(TARGET).elf
-	$(COFFCONVERT) -O coff-avr applet/$(TARGET).elf applet/$(TARGET).cof
-
-
-extcoff: applet/$(TARGET).elf
-	$(COFFCONVERT) -O coff-ext-avr applet/$(TARGET).elf applet/$(TARGET).cof
-
-
-.SUFFIXES: .elf .hex .eep .lss .sym .pde
-
-.elf.hex:
-	$(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@
-
-.elf.eep:
-	-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
-	--change-section-lma .eeprom=0 -O $(FORMAT) $< $@
-
-# Create extended listing file from ELF output file.
-.elf.lss:
-	$(OBJDUMP) -h -S $< > $@
-
-# Create a symbol table from ELF output file.
-.elf.sym:
-	$(NM) -n $< > $@
-
-
-# Compile: create object files from C++ source files.
-.cpp.o: $(HEADERS)
-	$(CXX) -c $(ALL_CXXFLAGS) $< -o $@ 
-
-# Compile: create object files from C source files.
-.c.o: $(HEADERS)
-	$(CC)  -c $(ALL_CFLAGS) $< -o $@ 
-
-
-# Compile: create assembler files from C source files.
-.c.s:
-	$(CC) -S $(ALL_CFLAGS) $< -o $@
-
-
-# Assemble: create object files from assembler source files.
-.S.o:
-	$(CC) -c $(ALL_ASFLAGS) $< -o $@
-
-
-
-applet/$(TARGET).cpp: $(TARGET).pde
-	test -d applet || mkdir applet
-	echo '#include "WProgram.h"' > applet/$(TARGET).cpp
-	echo '#include "avr/interrupt.h"' >> applet/$(TARGET).cpp
-	sed -n 's|^\(void .*)\).*|\1;|p' $(TARGET).pde | grep -v 'setup()' | \
-		grep -v 'loop()' >> applet/$(TARGET).cpp
-	cat $(TARGET).pde >> applet/$(TARGET).cpp
-	cat $(ARDUINO_SRC)/main.cxx >> applet/$(TARGET).cpp
-
-# Link: create ELF output file from object files.
-applet/$(TARGET).elf: applet/$(TARGET).cpp $(OBJ)
-	$(CC) $(ALL_CFLAGS) $(OBJ) --output $@ $(LDFLAGS)
-
-pd_close_serial:
-	echo 'close;' | /Applications/Pd-extended.app/Contents/Resources/bin/pdsend 34567 || true
-
-# Program the device.  
-upload: applet/$(TARGET).hex
-	$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH)
-
-
-pd_test: build pd_close_serial upload
-
-# Target: clean project.
-clean:
-	$(REMOVE) -- applet/$(TARGET).hex applet/$(TARGET).eep \
-	applet/$(TARGET).cof applet/$(TARGET).elf $(TARGET).map \
-	applet/$(TARGET).sym applet/$(TARGET).lss applet/$(TARGET).cpp \
-	$(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d)
-	rmdir -- applet
-
-depend:
-	if grep '^# DO NOT DELETE' $(MAKEFILE) >/dev/null; \
-	then \
-		sed -e '/^# DO NOT DELETE/,$$d' $(MAKEFILE) > \
-			$(MAKEFILE).$$$$ && \
-		$(MV) $(MAKEFILE).$$$$ $(MAKEFILE); \
-	fi
-	echo '# DO NOT DELETE THIS LINE -- make depend depends on it.' \
-		>> $(MAKEFILE); \
-	$(CC) -M -mmcu=$(MCU) $(CDEFS) $(INCLUDE) $(SRC) $(ASRC) >> $(MAKEFILE)
-
-.PHONY:	all build eep lss sym coff extcoff clean depend pd_close_serial pd_test
-
-# for emacs
-etags:
-	make etags_`uname -s`
-	etags *.pde \
-		$(ARDUINO_SRC)/*.[ch] \
-		$(ARDUINO_SRC)/*.cpp \
-		$(ARDUINO_LIB_SRC)/*/*.[ch] \
-		$(ARDUINO_LIB_SRC)/*/*.cpp \
-		$(ARDUINO)/hardware/tools/avr/avr/include/avr/*.[ch] \
-		$(ARDUINO)/hardware/tools/avr/avr/include/*.[ch]
-
-etags_Darwin:
-#	etags -a 
-
-etags_Linux:
-#	etags -a /usr/include/*.h linux/input.h /usr/include/sys/*.h
-
-etags_MINGW:
-#	etags -a /usr/include/*.h /usr/include/sys/*.h 
-
-
-
diff --git a/libraries/Firmata/examples/SimpleAnalogFirmata/SimpleAnalogFirmata.pde b/libraries/Firmata/examples/SimpleAnalogFirmata/SimpleAnalogFirmata.pde
deleted file mode 100644
index 430d0d0..0000000
--- a/libraries/Firmata/examples/SimpleAnalogFirmata/SimpleAnalogFirmata.pde
+++ /dev/null
@@ -1,32 +0,0 @@
-/* Supports as many analog inputs and analog PWM outputs as possible.
- *
- * This example code is in the public domain.
- */
-#include <Firmata.h>
-
-byte analogPin;
-
-void analogWriteCallback(byte pin, int value)
-{
-    pinMode(pin,OUTPUT);
-    analogWrite(pin, value);
-}
-
-void setup()
-{
-    Firmata.setFirmwareVersion(0, 1);
-    Firmata.attach(ANALOG_MESSAGE, analogWriteCallback);
-    Firmata.begin(57600);
-}
-
-void loop()
-{
-    while(Firmata.available()) {
-        Firmata.processInput();
-    }
-    for(analogPin = 0; analogPin < TOTAL_ANALOG_PINS; analogPin++) {
-        Firmata.sendAnalog(analogPin, analogRead(analogPin)); 
-    }
-}
-
-
diff --git a/libraries/Firmata/examples/SimpleDigitalFirmata/Makefile b/libraries/Firmata/examples/SimpleDigitalFirmata/Makefile
deleted file mode 100644
index e968c0a..0000000
--- a/libraries/Firmata/examples/SimpleDigitalFirmata/Makefile
+++ /dev/null
@@ -1,263 +0,0 @@
-# Arduino makefile
-#
-# This makefile allows you to build sketches from the command line
-# without the Arduino environment (or Java).
-#
-# The Arduino environment does preliminary processing on a sketch before
-# compiling it.  If you're using this makefile instead, you'll need to do
-# a few things differently:
-#
-#   - Give your program's file a .cpp extension (e.g. foo.cpp).
-#
-#   - Put this line at top of your code: #include <WProgram.h>
-#
-#   - Write prototypes for all your functions (or define them before you
-#     call them).  A prototype declares the types of parameters a
-#     function will take and what type of value it will return.  This
-#     means that you can have a call to a function before the definition
-#     of the function.  A function prototype looks like the first line of
-#     the function, with a semi-colon at the end.  For example:
-#     int digitalRead(int pin);
-#
-# Instructions for using the makefile:
-#
-#  1. Copy this file into the folder with your sketch.
-#
-#  2. Below, modify the line containing "TARGET" to refer to the name of
-#     of your program's file without an extension (e.g. TARGET = foo).
-#
-#  3. Modify the line containg "ARDUINO" to point the directory that
-#     contains the Arduino core (for normal Arduino installations, this
-#     is the hardware/cores/arduino sub-directory).
-#
-#  4. Modify the line containing "PORT" to refer to the filename
-#     representing the USB or serial connection to your Arduino board
-#     (e.g. PORT = /dev/tty.USB0).  If the exact name of this file
-#     changes, you can use * as a wildcard (e.g. PORT = /dev/tty.USB*).
-#
-#  5. At the command line, change to the directory containing your
-#     program's file and the makefile.
-#
-#  6. Type "make" and press enter to compile/verify your program.
-#
-#  7. Type "make upload", reset your Arduino board, and press enter  to
-#     upload your program to the Arduino board.
-#
-# $Id: Makefile,v 1.7 2007/04/13 05:28:23 eighthave Exp $
-
-PORT = /dev/tty.usbserial-*
-TARGET := $(shell pwd | sed 's|.*/\(.*\)|\1|')
-ARDUINO = /Applications/arduino
-ARDUINO_SRC = $(ARDUINO)/hardware/cores/arduino
-ARDUINO_LIB_SRC = $(ARDUINO)/hardware/libraries
-INCLUDE = -I$(ARDUINO_SRC) -I$(ARDUINO)/hardware/tools/avr/avr/include \
-	-I$(ARDUINO_LIB_SRC)/EEPROM \
-	-I$(ARDUINO_LIB_SRC)/Firmata \
-	-I$(ARDUINO_LIB_SRC)/Servo \
-	-I$(ARDUINO_LIB_SRC)
-SRC = $(wildcard $(ARDUINO_SRC)/*.c)
-CXXSRC = applet/$(TARGET).cpp $(ARDUINO_SRC)/HardwareSerial.cpp \
-	$(ARDUINO_LIB_SRC)/EEPROM/EEPROM.cpp \
-	$(ARDUINO_LIB_SRC)/Firmata/Firmata.cpp \
-	$(ARDUINO_LIB_SRC)/Servo/Servo.cpp \
-	$(ARDUINO_SRC)/WMath.cpp
-HEADERS = $(wildcard $(ARDUINO_SRC)/*.h) $(wildcard $(ARDUINO_LIB_SRC)/*/*.h)
-
-MCU = atmega168
-#MCU = atmega8
-F_CPU = 16000000
-FORMAT = ihex
-UPLOAD_RATE = 19200
-
-# Name of this Makefile (used for "make depend").
-MAKEFILE = Makefile
-
-# Debugging format.
-# Native formats for AVR-GCC's -g are stabs [default], or dwarf-2.
-# AVR (extended) COFF requires stabs, plus an avr-objcopy run.
-DEBUG = stabs
-
-OPT = s
-
-# Place -D or -U options here
-CDEFS = -DF_CPU=$(F_CPU)
-CXXDEFS = -DF_CPU=$(F_CPU)
-
-# Compiler flag to set the C Standard level.
-# c89   - "ANSI" C
-# gnu89 - c89 plus GCC extensions
-# c99   - ISO C99 standard (not yet fully implemented)
-# gnu99 - c99 plus GCC extensions
-CSTANDARD = -std=gnu99
-CDEBUG = -g$(DEBUG)
-CWARN = -Wall -Wstrict-prototypes
-CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums
-#CEXTRA = -Wa,-adhlns=$(<:.c=.lst)
-
-CFLAGS = $(CDEBUG) $(CDEFS) $(INCLUDE) -O$(OPT) $(CWARN) $(CSTANDARD) $(CEXTRA)
-CXXFLAGS = $(CDEFS) $(INCLUDE) -O$(OPT)
-#ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs 
-LDFLAGS = 
-
-
-# Programming support using avrdude. Settings and variables.
-AVRDUDE_PROGRAMMER = stk500
-AVRDUDE_PORT = $(PORT)
-AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex
-AVRDUDE_FLAGS = -F -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) \
-  -b $(UPLOAD_RATE) -q -V
-
-# Program settings
-CC = avr-gcc
-CXX = avr-g++
-OBJCOPY = avr-objcopy
-OBJDUMP = avr-objdump
-SIZE = avr-size
-NM = avr-nm
-AVRDUDE = avrdude
-REMOVE = rm -f
-MV = mv -f
-
-# Define all object files.
-OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o)
-
-# Define all listing files.
-LST = $(ASRC:.S=.lst) $(CXXSRC:.cpp=.lst) $(SRC:.c=.lst)
-
-# Combine all necessary flags and optional flags.
-# Add target processor to flags.
-ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS)
-ALL_CXXFLAGS = -mmcu=$(MCU) -I. $(CXXFLAGS)
-ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
-
-
-# Default target.
-all: build
-
-build: applet/$(TARGET).hex
-
-eep: applet/$(TARGET).eep
-lss: applet/$(TARGET).lss 
-sym: applet/$(TARGET).sym
-
-
-# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
-COFFCONVERT=$(OBJCOPY) --debugging \
---change-section-address .data-0x800000 \
---change-section-address .bss-0x800000 \
---change-section-address .noinit-0x800000 \
---change-section-address .eeprom-0x810000 
-
-
-coff: applet/$(TARGET).elf
-	$(COFFCONVERT) -O coff-avr applet/$(TARGET).elf applet/$(TARGET).cof
-
-
-extcoff: applet/$(TARGET).elf
-	$(COFFCONVERT) -O coff-ext-avr applet/$(TARGET).elf applet/$(TARGET).cof
-
-
-.SUFFIXES: .elf .hex .eep .lss .sym .pde
-
-.elf.hex:
-	$(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@
-
-.elf.eep:
-	-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
-	--change-section-lma .eeprom=0 -O $(FORMAT) $< $@
-
-# Create extended listing file from ELF output file.
-.elf.lss:
-	$(OBJDUMP) -h -S $< > $@
-
-# Create a symbol table from ELF output file.
-.elf.sym:
-	$(NM) -n $< > $@
-
-
-# Compile: create object files from C++ source files.
-.cpp.o: $(HEADERS)
-	$(CXX) -c $(ALL_CXXFLAGS) $< -o $@ 
-
-# Compile: create object files from C source files.
-.c.o: $(HEADERS)
-	$(CC)  -c $(ALL_CFLAGS) $< -o $@ 
-
-
-# Compile: create assembler files from C source files.
-.c.s:
-	$(CC) -S $(ALL_CFLAGS) $< -o $@
-
-
-# Assemble: create object files from assembler source files.
-.S.o:
-	$(CC) -c $(ALL_ASFLAGS) $< -o $@
-
-
-
-applet/$(TARGET).cpp: $(TARGET).pde
-	test -d applet || mkdir applet
-	echo '#include "WProgram.h"' > applet/$(TARGET).cpp
-	echo '#include "avr/interrupt.h"' >> applet/$(TARGET).cpp
-	sed -n 's|^\(void .*)\).*|\1;|p' $(TARGET).pde | grep -v 'setup()' | \
-		grep -v 'loop()' >> applet/$(TARGET).cpp
-	cat $(TARGET).pde >> applet/$(TARGET).cpp
-	cat $(ARDUINO_SRC)/main.cxx >> applet/$(TARGET).cpp
-
-# Link: create ELF output file from object files.
-applet/$(TARGET).elf: applet/$(TARGET).cpp $(OBJ)
-	$(CC) $(ALL_CFLAGS) $(OBJ) --output $@ $(LDFLAGS)
-
-pd_close_serial:
-	echo 'close;' | /Applications/Pd-extended.app/Contents/Resources/bin/pdsend 34567 || true
-
-# Program the device.  
-upload: applet/$(TARGET).hex
-	$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH)
-
-
-pd_test: build pd_close_serial upload
-
-# Target: clean project.
-clean:
-	$(REMOVE) -- applet/$(TARGET).hex applet/$(TARGET).eep \
-	applet/$(TARGET).cof applet/$(TARGET).elf $(TARGET).map \
-	applet/$(TARGET).sym applet/$(TARGET).lss applet/$(TARGET).cpp \
-	$(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d)
-	rmdir -- applet
-
-depend:
-	if grep '^# DO NOT DELETE' $(MAKEFILE) >/dev/null; \
-	then \
-		sed -e '/^# DO NOT DELETE/,$$d' $(MAKEFILE) > \
-			$(MAKEFILE).$$$$ && \
-		$(MV) $(MAKEFILE).$$$$ $(MAKEFILE); \
-	fi
-	echo '# DO NOT DELETE THIS LINE -- make depend depends on it.' \
-		>> $(MAKEFILE); \
-	$(CC) -M -mmcu=$(MCU) $(CDEFS) $(INCLUDE) $(SRC) $(ASRC) >> $(MAKEFILE)
-
-.PHONY:	all build eep lss sym coff extcoff clean depend pd_close_serial pd_test
-
-# for emacs
-etags:
-	make etags_`uname -s`
-	etags *.pde \
-		$(ARDUINO_SRC)/*.[ch] \
-		$(ARDUINO_SRC)/*.cpp \
-		$(ARDUINO_LIB_SRC)/*/*.[ch] \
-		$(ARDUINO_LIB_SRC)/*/*.cpp \
-		$(ARDUINO)/hardware/tools/avr/avr/include/avr/*.[ch] \
-		$(ARDUINO)/hardware/tools/avr/avr/include/*.[ch]
-
-etags_Darwin:
-#	etags -a 
-
-etags_Linux:
-#	etags -a /usr/include/*.h linux/input.h /usr/include/sys/*.h
-
-etags_MINGW:
-#	etags -a /usr/include/*.h /usr/include/sys/*.h 
-
-
-
diff --git a/libraries/Firmata/examples/SimpleDigitalFirmata/SimpleDigitalFirmata.pde b/libraries/Firmata/examples/SimpleDigitalFirmata/SimpleDigitalFirmata.pde
deleted file mode 100644
index 9c4e05d..0000000
--- a/libraries/Firmata/examples/SimpleDigitalFirmata/SimpleDigitalFirmata.pde
+++ /dev/null
@@ -1,58 +0,0 @@
-/* Supports as many digital inputs and outputs as possible.
- *
- * This example code is in the public domain.
- */
-#include <Firmata.h>
-
-byte previousPIN[2];  // PIN means PORT for input
-byte previousPORT[2]; 
-
-void outputPort(byte portNumber, byte portValue)
-{
-// only send the data when it changes, otherwise you get too many messages!
-    if(previousPIN[portNumber] != portValue) {
-        Firmata.sendDigitalPort(portNumber, portValue); 
-        previousPIN[portNumber] = portValue;
-        Firmata.sendDigitalPort(portNumber, portValue); 
-    }
-}
-
-void setPinModeCallback(byte pin, int mode) {
-    if(pin > 1) { // don't touch RxTx pins (0,1)
-        pinMode(pin, mode);
-    }
-}
-
-void digitalWriteCallback(byte port, int value)
-{
-    byte i;
-    byte currentPinValue, previousPinValue;
-
-    if(value != previousPORT[port]) {
-        for(i=0; i<8; i++) {
-            currentPinValue = (byte) value & (1 << i);
-            previousPinValue = previousPORT[port] & (1 << i);
-            if(currentPinValue != previousPinValue) {
-                digitalWrite(i + (port*8), currentPinValue);
-            }
-        }
-        previousPORT[port] = value;
-    }
-}
-
-void setup()
-{
-    Firmata.setFirmwareVersion(0, 1);
-    Firmata.attach(DIGITAL_MESSAGE, digitalWriteCallback);
-    Firmata.attach(SET_PIN_MODE, setPinModeCallback);
-    Firmata.begin(57600);
-}
-
-void loop()
-{
-    outputPort(0, PIND &~ B00000011); // pins 0-7, ignoring Rx/Tx pins (0/1)
-    outputPort(1, PINB); // pins 8-13
-    while(Firmata.available()) {
-        Firmata.processInput();
-    }
-}
diff --git a/libraries/Firmata/examples/StandardFirmata/LICENSE.txt b/libraries/Firmata/examples/StandardFirmata/LICENSE.txt
deleted file mode 100644
index 77cec6d..0000000
--- a/libraries/Firmata/examples/StandardFirmata/LICENSE.txt
+++ /dev/null
@@ -1,458 +0,0 @@
-
-		  GNU LESSER GENERAL PUBLIC LICENSE
-		       Version 2.1, February 1999
-
- Copyright (C) 1991, 1999 Free Software Foundation, Inc.
- 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301  USA
- Everyone is permitted to copy and distribute verbatim copies
- of this license document, but changing it is not allowed.
-
-[This is the first released version of the Lesser GPL.  It also counts
- as the successor of the GNU Library Public License, version 2, hence
- the version number 2.1.]
-
-			    Preamble
-
-  The licenses for most software are designed to take away your
-freedom to share and change it.  By contrast, the GNU General Public
-Licenses are intended to guarantee your freedom to share and change
-free software--to make sure the software is free for all its users.
-
-  This license, the Lesser General Public License, applies to some
-specially designated software packages--typically libraries--of the
-Free Software Foundation and other authors who decide to use it.  You
-can use it too, but we suggest you first think carefully about whether
-this license or the ordinary General Public License is the better
-strategy to use in any particular case, based on the explanations below.
-
-  When we speak of free software, we are referring to freedom of use,
-not price.  Our General Public Licenses are designed to make sure that
-you have the freedom to distribute copies of free software (and charge
-for this service if you wish); that you receive source code or can get
-it if you want it; that you can change the software and use pieces of
-it in new free programs; and that you are informed that you can do
-these things.
-
-  To protect your rights, we need to make restrictions that forbid
-distributors to deny you these rights or to ask you to surrender these
-rights.  These restrictions translate to certain responsibilities for
-you if you distribute copies of the library or if you modify it.
-
-  For example, if you distribute copies of the library, whether gratis
-or for a fee, you must give the recipients all the rights that we gave
-you.  You must make sure that they, too, receive or can get the source
-code.  If you link other code with the library, you must provide
-complete object files to the recipients, so that they can relink them
-with the library after making changes to the library and recompiling
-it.  And you must show them these terms so they know their rights.
-
-  We protect your rights with a two-step method: (1) we copyright the
-library, and (2) we offer you this license, which gives you legal
-permission to copy, distribute and/or modify the library.
-
-  To protect each distributor, we want to make it very clear that
-there is no warranty for the free library.  Also, if the library is
-modified by someone else and passed on, the recipients should know
-that what they have is not the original version, so that the original
-author's reputation will not be affected by problems that might be
-introduced by others.
-
-  Finally, software patents pose a constant threat to the existence of
-any free program.  We wish to make sure that a company cannot
-effectively restrict the users of a free program by obtaining a
-restrictive license from a patent holder.  Therefore, we insist that
-any patent license obtained for a version of the library must be
-consistent with the full freedom of use specified in this license.
-
-  Most GNU software, including some libraries, is covered by the
-ordinary GNU General Public License.  This license, the GNU Lesser
-General Public License, applies to certain designated libraries, and
-is quite different from the ordinary General Public License.  We use
-this license for certain libraries in order to permit linking those
-libraries into non-free programs.
-
-  When a program is linked with a library, whether statically or using
-a shared library, the combination of the two is legally speaking a
-combined work, a derivative of the original library.  The ordinary
-General Public License therefore permits such linking only if the
-entire combination fits its criteria of freedom.  The Lesser General
-Public License permits more lax criteria for linking other code with
-the library.
-
-  We call this license the "Lesser" General Public License because it
-does Less to protect the user's freedom than the ordinary General
-Public License.  It also provides other free software developers Less
-of an advantage over competing non-free programs.  These disadvantages
-are the reason we use the ordinary General Public License for many
-libraries.  However, the Lesser license provides advantages in certain
-special circumstances.
-
-  For example, on rare occasions, there may be a special need to
-encourage the widest possible use of a certain library, so that it becomes
-a de-facto standard.  To achieve this, non-free programs must be
-allowed to use the library.  A more frequent case is that a free
-library does the same job as widely used non-free libraries.  In this
-case, there is little to gain by limiting the free library to free
-software only, so we use the Lesser General Public License.
-
-  In other cases, permission to use a particular library in non-free
-programs enables a greater number of people to use a large body of
-free software.  For example, permission to use the GNU C Library in
-non-free programs enables many more people to use the whole GNU
-operating system, as well as its variant, the GNU/Linux operating
-system.
-
-  Although the Lesser General Public License is Less protective of the
-users' freedom, it does ensure that the user of a program that is
-linked with the Library has the freedom and the wherewithal to run
-that program using a modified version of the Library.
-
-  The precise terms and conditions for copying, distribution and
-modification follow.  Pay close attention to the difference between a
-"work based on the library" and a "work that uses the library".  The
-former contains code derived from the library, whereas the latter must
-be combined with the library in order to run.
-
-		  GNU LESSER GENERAL PUBLIC LICENSE
-   TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
-
-  0. This License Agreement applies to any software library or other
-program which contains a notice placed by the copyright holder or
-other authorized party saying it may be distributed under the terms of
-this Lesser General Public License (also called "this License").
-Each licensee is addressed as "you".
-
-  A "library" means a collection of software functions and/or data
-prepared so as to be conveniently linked with application programs
-(which use some of those functions and data) to form executables.
-
-  The "Library", below, refers to any such software library or work
-which has been distributed under these terms.  A "work based on the
-Library" means either the Library or any derivative work under
-copyright law: that is to say, a work containing the Library or a
-portion of it, either verbatim or with modifications and/or translated
-straightforwardly into another language.  (Hereinafter, translation is
-included without limitation in the term "modification".)
-
-  "Source code" for a work means the preferred form of the work for
-making modifications to it.  For a library, complete source code means
-all the source code for all modules it contains, plus any associated
-interface definition files, plus the scripts used to control compilation
-and installation of the library.
-
-  Activities other than copying, distribution and modification are not
-covered by this License; they are outside its scope.  The act of
-running a program using the Library is not restricted, and output from
-such a program is covered only if its contents constitute a work based
-on the Library (independent of the use of the Library in a tool for
-writing it).  Whether that is true depends on what the Library does
-and what the program that uses the Library does.
-  
-  1. You may copy and distribute verbatim copies of the Library's
-complete source code as you receive it, in any medium, provided that
-you conspicuously and appropriately publish on each copy an
-appropriate copyright notice and disclaimer of warranty; keep intact
-all the notices that refer to this License and to the absence of any
-warranty; and distribute a copy of this License along with the
-Library.
-
-  You may charge a fee for the physical act of transferring a copy,
-and you may at your option offer warranty protection in exchange for a
-fee.
-
-  2. You may modify your copy or copies of the Library or any portion
-of it, thus forming a work based on the Library, and copy and
-distribute such modifications or work under the terms of Section 1
-above, provided that you also meet all of these conditions:
-
-    a) The modified work must itself be a software library.
-
-    b) You must cause the files modified to carry prominent notices
-    stating that you changed the files and the date of any change.
-
-    c) You must cause the whole of the work to be licensed at no
-    charge to all third parties under the terms of this License.
-
-    d) If a facility in the modified Library refers to a function or a
-    table of data to be supplied by an application program that uses
-    the facility, other than as an argument passed when the facility
-    is invoked, then you must make a good faith effort to ensure that,
-    in the event an application does not supply such function or
-    table, the facility still operates, and performs whatever part of
-    its purpose remains meaningful.
-
-    (For example, a function in a library to compute square roots has
-    a purpose that is entirely well-defined independent of the
-    application.  Therefore, Subsection 2d requires that any
-    application-supplied function or table used by this function must
-    be optional: if the application does not supply it, the square
-    root function must still compute square roots.)
-
-These requirements apply to the modified work as a whole.  If
-identifiable sections of that work are not derived from the Library,
-and can be reasonably considered independent and separate works in
-themselves, then this License, and its terms, do not apply to those
-sections when you distribute them as separate works.  But when you
-distribute the same sections as part of a whole which is a work based
-on the Library, the distribution of the whole must be on the terms of
-this License, whose permissions for other licensees extend to the
-entire whole, and thus to each and every part regardless of who wrote
-it.
-
-Thus, it is not the intent of this section to claim rights or contest
-your rights to work written entirely by you; rather, the intent is to
-exercise the right to control the distribution of derivative or
-collective works based on the Library.
-
-In addition, mere aggregation of another work not based on the Library
-with the Library (or with a work based on the Library) on a volume of
-a storage or distribution medium does not bring the other work under
-the scope of this License.
-
-  3. You may opt to apply the terms of the ordinary GNU General Public
-License instead of this License to a given copy of the Library.  To do
-this, you must alter all the notices that refer to this License, so
-that they refer to the ordinary GNU General Public License, version 2,
-instead of to this License.  (If a newer version than version 2 of the
-ordinary GNU General Public License has appeared, then you can specify
-that version instead if you wish.)  Do not make any other change in
-these notices.
-
-  Once this change is made in a given copy, it is irreversible for
-that copy, so the ordinary GNU General Public License applies to all
-subsequent copies and derivative works made from that copy.
-
-  This option is useful when you wish to copy part of the code of
-the Library into a program that is not a library.
-
-  4. You may copy and distribute the Library (or a portion or
-derivative of it, under Section 2) in object code or executable form
-under the terms of Sections 1 and 2 above provided that you accompany
-it with the complete corresponding machine-readable source code, which
-must be distributed under the terms of Sections 1 and 2 above on a
-medium customarily used for software interchange.
-
-  If distribution of object code is made by offering access to copy
-from a designated place, then offering equivalent access to copy the
-source code from the same place satisfies the requirement to
-distribute the source code, even though third parties are not
-compelled to copy the source along with the object code.
-
-  5. A program that contains no derivative of any portion of the
-Library, but is designed to work with the Library by being compiled or
-linked with it, is called a "work that uses the Library".  Such a
-work, in isolation, is not a derivative work of the Library, and
-therefore falls outside the scope of this License.
-
-  However, linking a "work that uses the Library" with the Library
-creates an executable that is a derivative of the Library (because it
-contains portions of the Library), rather than a "work that uses the
-library".  The executable is therefore covered by this License.
-Section 6 states terms for distribution of such executables.
-
-  When a "work that uses the Library" uses material from a header file
-that is part of the Library, the object code for the work may be a
-derivative work of the Library even though the source code is not.
-Whether this is true is especially significant if the work can be
-linked without the Library, or if the work is itself a library.  The
-threshold for this to be true is not precisely defined by law.
-
-  If such an object file uses only numerical parameters, data
-structure layouts and accessors, and small macros and small inline
-functions (ten lines or less in length), then the use of the object
-file is unrestricted, regardless of whether it is legally a derivative
-work.  (Executables containing this object code plus portions of the
-Library will still fall under Section 6.)
-
-  Otherwise, if the work is a derivative of the Library, you may
-distribute the object code for the work under the terms of Section 6.
-Any executables containing that work also fall under Section 6,
-whether or not they are linked directly with the Library itself.
-
-  6. As an exception to the Sections above, you may also combine or
-link a "work that uses the Library" with the Library to produce a
-work containing portions of the Library, and distribute that work
-under terms of your choice, provided that the terms permit
-modification of the work for the customer's own use and reverse
-engineering for debugging such modifications.
-
-  You must give prominent notice with each copy of the work that the
-Library is used in it and that the Library and its use are covered by
-this License.  You must supply a copy of this License.  If the work
-during execution displays copyright notices, you must include the
-copyright notice for the Library among them, as well as a reference
-directing the user to the copy of this License.  Also, you must do one
-of these things:
-
-    a) Accompany the work with the complete corresponding
-    machine-readable source code for the Library including whatever
-    changes were used in the work (which must be distributed under
-    Sections 1 and 2 above); and, if the work is an executable linked
-    with the Library, with the complete machine-readable "work that
-    uses the Library", as object code and/or source code, so that the
-    user can modify the Library and then relink to produce a modified
-    executable containing the modified Library.  (It is understood
-    that the user who changes the contents of definitions files in the
-    Library will not necessarily be able to recompile the application
-    to use the modified definitions.)
-
-    b) Use a suitable shared library mechanism for linking with the
-    Library.  A suitable mechanism is one that (1) uses at run time a
-    copy of the library already present on the user's computer system,
-    rather than copying library functions into the executable, and (2)
-    will operate properly with a modified version of the library, if
-    the user installs one, as long as the modified version is
-    interface-compatible with the version that the work was made with.
-
-    c) Accompany the work with a written offer, valid for at
-    least three years, to give the same user the materials
-    specified in Subsection 6a, above, for a charge no more
-    than the cost of performing this distribution.
-
-    d) If distribution of the work is made by offering access to copy
-    from a designated place, offer equivalent access to copy the above
-    specified materials from the same place.
-
-    e) Verify that the user has already received a copy of these
-    materials or that you have already sent this user a copy.
-
-  For an executable, the required form of the "work that uses the
-Library" must include any data and utility programs needed for
-reproducing the executable from it.  However, as a special exception,
-the materials to be distributed need not include anything that is
-normally distributed (in either source or binary form) with the major
-components (compiler, kernel, and so on) of the operating system on
-which the executable runs, unless that component itself accompanies
-the executable.
-
-  It may happen that this requirement contradicts the license
-restrictions of other proprietary libraries that do not normally
-accompany the operating system.  Such a contradiction means you cannot
-use both them and the Library together in an executable that you
-distribute.
-
-  7. You may place library facilities that are a work based on the
-Library side-by-side in a single library together with other library
-facilities not covered by this License, and distribute such a combined
-library, provided that the separate distribution of the work based on
-the Library and of the other library facilities is otherwise
-permitted, and provided that you do these two things:
-
-    a) Accompany the combined library with a copy of the same work
-    based on the Library, uncombined with any other library
-    facilities.  This must be distributed under the terms of the
-    Sections above.
-
-    b) Give prominent notice with the combined library of the fact
-    that part of it is a work based on the Library, and explaining
-    where to find the accompanying uncombined form of the same work.
-
-  8. You may not copy, modify, sublicense, link with, or distribute
-the Library except as expressly provided under this License.  Any
-attempt otherwise to copy, modify, sublicense, link with, or
-distribute the Library is void, and will automatically terminate your
-rights under this License.  However, parties who have received copies,
-or rights, from you under this License will not have their licenses
-terminated so long as such parties remain in full compliance.
-
-  9. You are not required to accept this License, since you have not
-signed it.  However, nothing else grants you permission to modify or
-distribute the Library or its derivative works.  These actions are
-prohibited by law if you do not accept this License.  Therefore, by
-modifying or distributing the Library (or any work based on the
-Library), you indicate your acceptance of this License to do so, and
-all its terms and conditions for copying, distributing or modifying
-the Library or works based on it.
-
-  10. Each time you redistribute the Library (or any work based on the
-Library), the recipient automatically receives a license from the
-original licensor to copy, distribute, link with or modify the Library
-subject to these terms and conditions.  You may not impose any further
-restrictions on the recipients' exercise of the rights granted herein.
-You are not responsible for enforcing compliance by third parties with
-this License.
-
-  11. If, as a consequence of a court judgment or allegation of patent
-infringement or for any other reason (not limited to patent issues),
-conditions are imposed on you (whether by court order, agreement or
-otherwise) that contradict the conditions of this License, they do not
-excuse you from the conditions of this License.  If you cannot
-distribute so as to satisfy simultaneously your obligations under this
-License and any other pertinent obligations, then as a consequence you
-may not distribute the Library at all.  For example, if a patent
-license would not permit royalty-free redistribution of the Library by
-all those who receive copies directly or indirectly through you, then
-the only way you could satisfy both it and this License would be to
-refrain entirely from distribution of the Library.
-
-If any portion of this section is held invalid or unenforceable under any
-particular circumstance, the balance of the section is intended to apply,
-and the section as a whole is intended to apply in other circumstances.
-
-It is not the purpose of this section to induce you to infringe any
-patents or other property right claims or to contest validity of any
-such claims; this section has the sole purpose of protecting the
-integrity of the free software distribution system which is
-implemented by public license practices.  Many people have made
-generous contributions to the wide range of software distributed
-through that system in reliance on consistent application of that
-system; it is up to the author/donor to decide if he or she is willing
-to distribute software through any other system and a licensee cannot
-impose that choice.
-
-This section is intended to make thoroughly clear what is believed to
-be a consequence of the rest of this License.
-
-  12. If the distribution and/or use of the Library is restricted in
-certain countries either by patents or by copyrighted interfaces, the
-original copyright holder who places the Library under this License may add
-an explicit geographical distribution limitation excluding those countries,
-so that distribution is permitted only in or among countries not thus
-excluded.  In such case, this License incorporates the limitation as if
-written in the body of this License.
-
-  13. The Free Software Foundation may publish revised and/or new
-versions of the Lesser General Public License from time to time.
-Such new versions will be similar in spirit to the present version,
-but may differ in detail to address new problems or concerns.
-
-Each version is given a distinguishing version number.  If the Library
-specifies a version number of this License which applies to it and
-"any later version", you have the option of following the terms and
-conditions either of that version or of any later version published by
-the Free Software Foundation.  If the Library does not specify a
-license version number, you may choose any version ever published by
-the Free Software Foundation.
-
-  14. If you wish to incorporate parts of the Library into other free
-programs whose distribution conditions are incompatible with these,
-write to the author to ask for permission.  For software which is
-copyrighted by the Free Software Foundation, write to the Free
-Software Foundation; we sometimes make exceptions for this.  Our
-decision will be guided by the two goals of preserving the free status
-of all derivatives of our free software and of promoting the sharing
-and reuse of software generally.
-
-			    NO WARRANTY
-
-  15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO
-WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW.
-EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR
-OTHER PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY OF ANY
-KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
-IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-PURPOSE.  THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE
-LIBRARY IS WITH YOU.  SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME
-THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
-
-  16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN
-WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY
-AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU
-FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
-CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE
-LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING
-RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A
-FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF
-SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
-DAMAGES.
-
diff --git a/libraries/Firmata/examples/StandardFirmata/Makefile b/libraries/Firmata/examples/StandardFirmata/Makefile
deleted file mode 100644
index 835187a..0000000
--- a/libraries/Firmata/examples/StandardFirmata/Makefile
+++ /dev/null
@@ -1,273 +0,0 @@
-# Arduino makefile
-#
-# This makefile allows you to build sketches from the command line
-# without the Arduino environment (or Java).
-#
-# The Arduino environment does preliminary processing on a sketch before
-# compiling it.  If you're using this makefile instead, you'll need to do
-# a few things differently:
-#
-#   - Give your program's file a .cpp extension (e.g. foo.cpp).
-#
-#   - Put this line at top of your code: #include <WProgram.h>
-#
-#   - Write prototypes for all your functions (or define them before you
-#     call them).  A prototype declares the types of parameters a
-#     function will take and what type of value it will return.  This
-#     means that you can have a call to a function before the definition
-#     of the function.  A function prototype looks like the first line of
-#     the function, with a semi-colon at the end.  For example:
-#     int digitalRead(int pin);
-#
-# Instructions for using the makefile:
-#
-#  1. Copy this file into the folder with your sketch.
-#
-#  2. Below, modify the line containing "TARGET" to refer to the name of
-#     of your program's file without an extension (e.g. TARGET = foo).
-#
-#  3. Modify the line containg "ARDUINO" to point the directory that
-#     contains the Arduino core (for normal Arduino installations, this
-#     is the hardware/cores/arduino sub-directory).
-#
-#  4. Modify the line containing "PORT" to refer to the filename
-#     representing the USB or serial connection to your Arduino board
-#     (e.g. PORT = /dev/tty.USB0).  If the exact name of this file
-#     changes, you can use * as a wildcard (e.g. PORT = /dev/tty.USB*).
-#
-#  5. At the command line, change to the directory containing your
-#     program's file and the makefile.
-#
-#  6. Type "make" and press enter to compile/verify your program.
-#
-#  7. Type "make upload", reset your Arduino board, and press enter  to
-#     upload your program to the Arduino board.
-#
-# $Id: Makefile,v 1.7 2007/04/13 05:28:23 eighthave Exp $
-
-PORT = /dev/tty.usbserial-*
-TARGET := $(shell pwd | sed 's|.*/\(.*\)|\1|')
-ARDUINO = /Applications/arduino
-ARDUINO_SRC = $(ARDUINO)/hardware/cores/arduino
-ARDUINO_LIB_SRC = $(ARDUINO)/hardware/libraries
-ARDUINO_TOOLS = $(ARDUINO)/hardware/tools
-INCLUDE = -I$(ARDUINO_SRC) -I$(ARDUINO)/hardware/tools/avr/avr/include \
-	-I$(ARDUINO_LIB_SRC)/EEPROM \
-	-I$(ARDUINO_LIB_SRC)/Firmata \
-	-I$(ARDUINO_LIB_SRC)/Matrix \
-	-I$(ARDUINO_LIB_SRC)/Servo \
-	-I$(ARDUINO_LIB_SRC)/Wire \
-	-I$(ARDUINO_LIB_SRC)
-SRC = $(wildcard $(ARDUINO_SRC)/*.c)
-CXXSRC = applet/$(TARGET).cpp $(ARDUINO_SRC)/HardwareSerial.cpp \
-	$(ARDUINO_LIB_SRC)/EEPROM/EEPROM.cpp \
-	$(ARDUINO_LIB_SRC)/Firmata/Firmata.cpp \
-	$(ARDUINO_LIB_SRC)/Servo/Servo.cpp \
-	$(ARDUINO_SRC)/Print.cpp \
-	$(ARDUINO_SRC)/WMath.cpp
-HEADERS = $(wildcard $(ARDUINO_SRC)/*.h) $(wildcard $(ARDUINO_LIB_SRC)/*/*.h)
-
-MCU = atmega168
-#MCU = atmega8
-F_CPU = 16000000
-FORMAT = ihex
-UPLOAD_RATE = 19200
-
-# Name of this Makefile (used for "make depend").
-MAKEFILE = Makefile
-
-# Debugging format.
-# Native formats for AVR-GCC's -g are stabs [default], or dwarf-2.
-# AVR (extended) COFF requires stabs, plus an avr-objcopy run.
-DEBUG = stabs
-
-OPT = s
-
-# Place -D or -U options here
-CDEFS = -DF_CPU=$(F_CPU)
-CXXDEFS = -DF_CPU=$(F_CPU)
-
-# Compiler flag to set the C Standard level.
-# c89   - "ANSI" C
-# gnu89 - c89 plus GCC extensions
-# c99   - ISO C99 standard (not yet fully implemented)
-# gnu99 - c99 plus GCC extensions
-CSTANDARD = -std=gnu99
-CDEBUG = -g$(DEBUG)
-CWARN = -Wall -Wstrict-prototypes
-CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums
-#CEXTRA = -Wa,-adhlns=$(<:.c=.lst)
-
-CFLAGS = $(CDEBUG) $(CDEFS) $(INCLUDE) -O$(OPT) $(CWARN) $(CSTANDARD) $(CEXTRA)
-CXXFLAGS = $(CDEFS) $(INCLUDE) -O$(OPT)
-#ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs 
-LDFLAGS = 
-
-
-# Programming support using avrdude. Settings and variables.
-AVRDUDE_PROGRAMMER = stk500
-AVRDUDE_PORT = $(PORT)
-AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex
-AVRDUDE_FLAGS = -F -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) \
-  -b $(UPLOAD_RATE) -q -V
-
-# Program settings
-ARDUINO_AVR_BIN = $(ARDUINO_TOOLS)/avr/bin
-CC = $(ARDUINO_AVR_BIN)/avr-gcc 
-CXX = $(ARDUINO_AVR_BIN)/avr-g++
-OBJCOPY = $(ARDUINO_AVR_BIN)/avr-objcopy
-OBJDUMP = $(ARDUINO_AVR_BIN)/avr-objdump
-SIZE = $(ARDUINO_AVR_BIN)/avr-size
-NM = $(ARDUINO_AVR_BIN)/avr-nm
-#AVRDUDE = $(ARDUINO_AVR_BIN)/avrdude
-AVRDUDE = avrdude
-REMOVE = rm -f
-MV = mv -f
-
-# Define all object files.
-OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o)
-
-# Define all listing files.
-LST = $(ASRC:.S=.lst) $(CXXSRC:.cpp=.lst) $(SRC:.c=.lst)
-
-# Combine all necessary flags and optional flags.
-# Add target processor to flags.
-ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS)
-ALL_CXXFLAGS = -mmcu=$(MCU) -I. $(CXXFLAGS)
-ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
-
-
-# Default target.
-all: build
-
-build: applet/$(TARGET).hex
-
-eep: applet/$(TARGET).eep
-lss: applet/$(TARGET).lss 
-sym: applet/$(TARGET).sym
-
-
-# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
-COFFCONVERT=$(OBJCOPY) --debugging \
---change-section-address .data-0x800000 \
---change-section-address .bss-0x800000 \
---change-section-address .noinit-0x800000 \
---change-section-address .eeprom-0x810000 
-
-
-coff: applet/$(TARGET).elf
-	$(COFFCONVERT) -O coff-avr applet/$(TARGET).elf applet/$(TARGET).cof
-
-
-extcoff: applet/$(TARGET).elf
-	$(COFFCONVERT) -O coff-ext-avr applet/$(TARGET).elf applet/$(TARGET).cof
-
-
-.SUFFIXES: .elf .hex .eep .lss .sym .pde
-
-.elf.hex:
-	$(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@
-
-.elf.eep:
-	-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
-	--change-section-lma .eeprom=0 -O $(FORMAT) $< $@
-
-# Create extended listing file from ELF output file.
-.elf.lss:
-	$(OBJDUMP) -h -S $< > $@
-
-# Create a symbol table from ELF output file.
-.elf.sym:
-	$(NM) -n $< > $@
-
-
-# Compile: create object files from C++ source files.
-.cpp.o: $(HEADERS)
-	$(CXX) -c $(ALL_CXXFLAGS) $< -o $@ 
-
-# Compile: create object files from C source files.
-.c.o: $(HEADERS)
-	$(CC)  -c $(ALL_CFLAGS) $< -o $@ 
-
-
-# Compile: create assembler files from C source files.
-.c.s:
-	$(CC) -S $(ALL_CFLAGS) $< -o $@
-
-
-# Assemble: create object files from assembler source files.
-.S.o:
-	$(CC) -c $(ALL_ASFLAGS) $< -o $@
-
-
-
-applet/$(TARGET).cpp: $(TARGET).pde
-	test -d applet || mkdir applet
-	echo '#include "WProgram.h"' > applet/$(TARGET).cpp
-	echo '#include "avr/interrupt.h"' >> applet/$(TARGET).cpp
-	sed -n 's|^\(void .*)\).*|\1;|p' $(TARGET).pde | grep -v 'setup()' | \
-		grep -v 'loop()' >> applet/$(TARGET).cpp
-	cat $(TARGET).pde >> applet/$(TARGET).cpp
-	cat $(ARDUINO_SRC)/main.cxx >> applet/$(TARGET).cpp
-
-# Link: create ELF output file from object files.
-applet/$(TARGET).elf: applet/$(TARGET).cpp $(OBJ)
-	$(CC) $(ALL_CFLAGS) $(OBJ) -lm --output $@ $(LDFLAGS)
-#	$(CC) $(ALL_CFLAGS) $(OBJ) $(ARDUINO_TOOLS)/avr/avr/lib/avr5/crtm168.o --output $@ $(LDFLAGS)
-
-pd_close_serial:
-	echo 'close;' | /Applications/Pd-extended.app/Contents/Resources/bin/pdsend 34567 || true
-
-# Program the device.  
-upload: applet/$(TARGET).hex
-	$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH)
-
-
-pd_test: build pd_close_serial upload
-
-# Target: clean project.
-clean:
-	$(REMOVE) -- applet/$(TARGET).hex applet/$(TARGET).eep \
-	applet/$(TARGET).cof applet/$(TARGET).elf $(TARGET).map \
-	applet/$(TARGET).sym applet/$(TARGET).lss applet/$(TARGET).cpp \
-	$(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d)
-	rmdir -- applet
-
-depend:
-	if grep '^# DO NOT DELETE' $(MAKEFILE) >/dev/null; \
-	then \
-		sed -e '/^# DO NOT DELETE/,$$d' $(MAKEFILE) > \
-			$(MAKEFILE).$$$$ && \
-		$(MV) $(MAKEFILE).$$$$ $(MAKEFILE); \
-	fi
-	echo '# DO NOT DELETE THIS LINE -- make depend depends on it.' \
-		>> $(MAKEFILE); \
-	$(CC) -M -mmcu=$(MCU) $(CDEFS) $(INCLUDE) $(SRC) $(ASRC) >> $(MAKEFILE)
-
-.PHONY:	all build eep lss sym coff extcoff clean depend pd_close_serial pd_test
-
-# for emacs
-etags:
-	make etags_`uname -s`
-	etags *.pde \
-		$(ARDUINO_SRC)/*.[ch] \
-		$(ARDUINO_SRC)/*.cpp \
-		$(ARDUINO_LIB_SRC)/*/*.[ch] \
-		$(ARDUINO_LIB_SRC)/*/*.cpp \
-		$(ARDUINO)/hardware/tools/avr/avr/include/avr/*.[ch] \
-		$(ARDUINO)/hardware/tools/avr/avr/include/*.[ch]
-
-etags_Darwin:
-#	etags -a 
-
-etags_Linux:
-#	etags -a /usr/include/*.h linux/input.h /usr/include/sys/*.h
-
-etags_MINGW:
-#	etags -a /usr/include/*.h /usr/include/sys/*.h 
-
-
-path:
-	echo $(PATH)
-	echo $$PATH
-
diff --git a/libraries/Firmata/examples/StandardFirmata/StandardFirmata.pde b/libraries/Firmata/examples/StandardFirmata/StandardFirmata.pde
deleted file mode 100644
index 16c8b87..0000000
--- a/libraries/Firmata/examples/StandardFirmata/StandardFirmata.pde
+++ /dev/null
@@ -1,293 +0,0 @@
-/*
-  Copyright (C) 2006-2008 Hans-Christoph Steiner.  All rights reserved.
-  
-  This library is free software; you can redistribute it and/or
-  modify it under the terms of the GNU Lesser General Public
-  License as published by the Free Software Foundation; either
-  version 2.1 of the License, or (at your option) any later version.
- 
-  See file LICENSE.txt for further informations on licensing terms.
-
-  formatted using the GNU C formatting and indenting
-*/
-
-
-/* 
- * TODO: add Servo support using setPinModeCallback(pin, SERVO);
- * TODO: use Program Control to load stored profiles from EEPROM
- */
-
-#include <Firmata.h>
-#include <Servo.h>
-
-/*==============================================================================
- * GLOBAL VARIABLES
- *============================================================================*/
-
-/* analog inputs */
-int analogInputsToReport = 0; // bitwise array to store pin reporting
-int analogPin = 0; // counter for reading analog pins
-
-/* digital pins */
-byte reportPINs[TOTAL_PORTS];   // PIN == input port
-byte previousPINs[TOTAL_PORTS]; // PIN == input port
-byte pinStatus[TOTAL_DIGITAL_PINS]; // store pin status, default OUTPUT
-byte portStatus[TOTAL_PORTS];
-
-/* timer variables */
-unsigned long currentMillis;     // store the current value from millis()
-unsigned long nextExecuteMillis; // for comparison with currentMillis
-int samplingInterval = 19;      // how often to run the main loop (in ms)
-
-Servo servos[2]; // the servo library can control servos on pins 9 and 10 only
-
-/*==============================================================================
- * FUNCTIONS
- *============================================================================*/
-
-void outputPort(byte portNumber, byte portValue)
-{
-  portValue = portValue &~ portStatus[portNumber];
-  if(previousPINs[portNumber] != portValue) {
-    Firmata.sendDigitalPort(portNumber, portValue);
-    previousPINs[portNumber] = portValue;
-    Firmata.sendDigitalPort(portNumber, portValue);
-  }
-}
-
-/* -----------------------------------------------------------------------------
- * check all the active digital inputs for change of state, then add any events
- * to the Serial output queue using Serial.print() */
-void checkDigitalInputs(void)
-{
-  byte i, tmp;
-  for(i=0; i < TOTAL_PORTS; i++) {
-    if(reportPINs[i]) {
-      switch(i) {
-      case 0:
-        outputPort(0, PIND &~ B00000011); // ignore Rx/Tx 0/1
-        break;
-      case 1:
-        outputPort(1, PINB);
-        break;
-      case ANALOG_PORT:
-        outputPort(ANALOG_PORT, PINC);
-        break;
-      }
-    }
-  }
-}
-
-// -----------------------------------------------------------------------------
-/* sets the pin mode to the correct state and sets the relevant bits in the
- * two bit-arrays that track Digital I/O and PWM status
- */
-void setPinModeCallback(byte pin, int mode) {
-  byte port = 0;
-  byte offset = 0;
-
-  // TODO: abstract for different boards
-  if (pin < 8) {
-    port = 0;
-    offset = 0;
-  } else if (pin < 14) {
-    port = 1;
-    offset = 8;
-  } else if (pin < 22) {
-    port = 2;
-    offset = 14;
-  }
-  
-  if(pin > 1) { // ignore RxTx (pins 0 and 1)
-    if(pin > 13) 
-      reportAnalogCallback(pin - 14, mode == ANALOG ? 1 : 0); // turn on/off reporting
-    switch(mode) {
-    case ANALOG:
-      digitalWrite(pin, LOW); // disable internal pull-ups and fall thru to 'case INPUT:'
-    case INPUT:
-      pinStatus[pin] = mode;
-      pinMode(pin, INPUT);
-      portStatus[port] = portStatus[port] &~ (1 << (pin - offset));
-      break;
-    case OUTPUT:
-      digitalWrite(pin, LOW); // disable PWM and fall thru to 'case PWM:' 
-    case PWM:
-      pinStatus[pin] = mode;
-      pinMode(pin, OUTPUT);
-      portStatus[port] = portStatus[port] | (1 << (pin - offset));
-      break;
-    case SERVO:
-      if((pin == 9 || pin == 10))
-        pinStatus[pin] = mode;
-      else
-        Firmata.sendString("Servo only on pins 9 and 10");
-      break;
-    case I2C:
-      pinStatus[pin] = mode;
-      Firmata.sendString("I2C mode not yet supported");
-      break;
-    default:
-      Firmata.sendString("Unknown pin mode"); // TODO: put error msgs in EEPROM
-    }
-    // TODO: save status to EEPROM here, if changed
-  }
-}
-
-void analogWriteCallback(byte pin, int value)
-{
-  switch(pinStatus[pin]) {
-  case SERVO:
-    if(pin == 9)  servos[0].write(value);
-    if(pin == 10) servos[1].write(value);
-    break;
-  case PWM:
-    analogWrite(pin, value);
-    break;
-  }
-}
-
-void digitalWriteCallback(byte port, int value)
-{
-  switch(port) {
-  case 0: // pins 2-7 (don't change Rx/Tx, pins 0 and 1)
-    // 0xFF03 == B1111111100000011    0x03 == B00000011
-    PORTD = (value &~ 0xFF03) | (PORTD & 0x03);
-    break;
-  case 1: // pins 8-13 (14,15 are disabled for the crystal) 
-    PORTB = (byte)value;
-    break;
-  case 2: // analog pins used as digital
-    byte pin;
-    byte pinModeMask;
-    for(pin=0; pin<8; pin++)
-      if(pinStatus[pin] == OUTPUT)
-        pinModeMask += 1 << pin;
-    PORTC = (byte)value & pinModeMask;
-    break;
-  }
-}
-
-// -----------------------------------------------------------------------------
-/* sets bits in a bit array (int) to toggle the reporting of the analogIns
- */
-//void FirmataClass::setAnalogPinReporting(byte pin, byte state) {
-//}
-void reportAnalogCallback(byte pin, int value)
-{
-  if(value == 0) {
-    analogInputsToReport = analogInputsToReport &~ (1 << pin);
-  }
-  else { // everything but 0 enables reporting of that pin
-    analogInputsToReport = analogInputsToReport | (1 << pin);
-    setPinModeCallback(pin, ANALOG);
-  }
-  // TODO: save status to EEPROM here, if changed
-}
-
-void reportDigitalCallback(byte port, int value)
-{
-  reportPINs[port] = (byte)value;
-  if(port == ANALOG_PORT) // turn off analog reporting when used as digital
-    analogInputsToReport = 0;
-}
-
-/*==============================================================================
- * SYSEX-BASED commands
- *============================================================================*/
-
-void sysexCallback(byte command, byte argc, byte *argv)
-{
-  switch(command) {
-  case SERVO_CONFIG:
-    if(argc > 4) {
-      // these vars are here for clarity, they'll optimized away by the compiler
-      byte pin = argv[0] - 9; // servos are pins 9 and 10, so offset for array
-      int minPulse = argv[1] + (argv[2] << 7);
-      int maxPulse = argv[3] + (argv[4] << 7);
-      servos[pin].attach(argv[0], minPulse, maxPulse);
-      // TODO does the Servo have to be detach()ed before reconfiguring?
-      setPinModeCallback(pin, SERVO);
-    }
-    break;
-  case SAMPLING_INTERVAL:
-    if (argc > 1)
-      samplingInterval = argv[0] + (argv[1] << 7);
-    else
-      Firmata.sendString("Not enough data");
-    break;
-  }
-}
-
-
-/*==============================================================================
- * SETUP()
- *============================================================================*/
-void setup() 
-{
-  byte i;
-
-  Firmata.setFirmwareVersion(2, 1);
-
-  Firmata.attach(ANALOG_MESSAGE, analogWriteCallback);
-  Firmata.attach(DIGITAL_MESSAGE, digitalWriteCallback);
-  Firmata.attach(REPORT_ANALOG, reportAnalogCallback);
-  Firmata.attach(REPORT_DIGITAL, reportDigitalCallback);
-  Firmata.attach(SET_PIN_MODE, setPinModeCallback);
-  Firmata.attach(START_SYSEX, sysexCallback);
-
-  portStatus[0] = B00000011;  // ignore Tx/RX pins
-  portStatus[1] = B11000000;  // ignore 14/15 pins 
-  portStatus[2] = B00000000;
-
-  for(i=0; i<TOTAL_DIGITAL_PINS; ++i) { // TODO make this work with analogs
-    setPinModeCallback(i,OUTPUT);
-  }
-  // set all outputs to 0 to make sure internal pull-up resistors are off
-  PORTB = 0; // pins 8-15
-  PORTC = 0; // analog port
-  PORTD = 0; // pins 0-7
-
-  // TODO rethink the init, perhaps it should report analog on default
-  for(i=0; i<TOTAL_PORTS; ++i) {
-    reportPINs[i] = false;
-  }
-  // TODO: load state from EEPROM here
-
-  /* send digital inputs here, if enabled, to set the initial state on the
-   * host computer, since once in the loop(), this firmware will only send
-   * digital data on change. */
-  if(reportPINs[0]) outputPort(0, PIND &~ B00000011); // ignore Rx/Tx 0/1
-  if(reportPINs[1]) outputPort(1, PINB);
-  if(reportPINs[ANALOG_PORT]) outputPort(ANALOG_PORT, PINC);
-
-  Firmata.begin(57600);
-}
-
-/*==============================================================================
- * LOOP()
- *============================================================================*/
-void loop() 
-{
-  /* DIGITALREAD - as fast as possible, check for changes and output them to the
-   * FTDI buffer using Serial.print()  */
-  checkDigitalInputs();  
-  currentMillis = millis();
-  if(currentMillis > nextExecuteMillis) {  
-    nextExecuteMillis = currentMillis + samplingInterval;
-    /* SERIALREAD - Serial.read() uses a 128 byte circular buffer, so handle
-     * all serialReads at once, i.e. empty the buffer */
-    while(Firmata.available())
-      Firmata.processInput();
-    /* SEND FTDI WRITE BUFFER - make sure that the FTDI buffer doesn't go over
-     * 60 bytes. use a timer to sending an event character every 4 ms to
-     * trigger the buffer to dump. */
-	
-    /* ANALOGREAD - right after the event character, do all of the
-     * analogReads().  These only need to be done every 4ms. */
-    for(analogPin=0;analogPin<TOTAL_ANALOG_PINS;analogPin++) {
-      if( analogInputsToReport & (1 << analogPin) ) {
-        Firmata.sendAnalog(analogPin, analogRead(analogPin));
-      }
-    }
-  }
-}