Moving libraries out of arduino platform / core directory and to top-level.

1 files changed, 0 insertions, 293 deletions

diff --git a/libraries/Firmata/examples/StandardFirmata/StandardFirmata.pde b/libraries/Firmata/examples/StandardFirmata/StandardFirmata.pde
deleted file mode 100644
index 16c8b87..0000000
--- a/libraries/Firmata/examples/StandardFirmata/StandardFirmata.pde
+++ /dev/null
@@ -1,293 +0,0 @@
-/*
-  Copyright (C) 2006-2008 Hans-Christoph Steiner.  All rights reserved.
-  
-  This library is free software; you can redistribute it and/or
-  modify it under the terms of the GNU Lesser General Public
-  License as published by the Free Software Foundation; either
-  version 2.1 of the License, or (at your option) any later version.
- 
-  See file LICENSE.txt for further informations on licensing terms.
-
-  formatted using the GNU C formatting and indenting
-*/
-
-
-/* 
- * TODO: add Servo support using setPinModeCallback(pin, SERVO);
- * TODO: use Program Control to load stored profiles from EEPROM
- */
-
-#include <Firmata.h>
-#include <Servo.h>
-
-/*==============================================================================
- * GLOBAL VARIABLES
- *============================================================================*/
-
-/* analog inputs */
-int analogInputsToReport = 0; // bitwise array to store pin reporting
-int analogPin = 0; // counter for reading analog pins
-
-/* digital pins */
-byte reportPINs[TOTAL_PORTS];   // PIN == input port
-byte previousPINs[TOTAL_PORTS]; // PIN == input port
-byte pinStatus[TOTAL_DIGITAL_PINS]; // store pin status, default OUTPUT
-byte portStatus[TOTAL_PORTS];
-
-/* timer variables */
-unsigned long currentMillis;     // store the current value from millis()
-unsigned long nextExecuteMillis; // for comparison with currentMillis
-int samplingInterval = 19;      // how often to run the main loop (in ms)
-
-Servo servos[2]; // the servo library can control servos on pins 9 and 10 only
-
-/*==============================================================================
- * FUNCTIONS
- *============================================================================*/
-
-void outputPort(byte portNumber, byte portValue)
-{
-  portValue = portValue &~ portStatus[portNumber];
-  if(previousPINs[portNumber] != portValue) {
-    Firmata.sendDigitalPort(portNumber, portValue);
-    previousPINs[portNumber] = portValue;
-    Firmata.sendDigitalPort(portNumber, portValue);
-  }
-}
-
-/* -----------------------------------------------------------------------------
- * check all the active digital inputs for change of state, then add any events
- * to the Serial output queue using Serial.print() */
-void checkDigitalInputs(void)
-{
-  byte i, tmp;
-  for(i=0; i < TOTAL_PORTS; i++) {
-    if(reportPINs[i]) {
-      switch(i) {
-      case 0:
-        outputPort(0, PIND &~ B00000011); // ignore Rx/Tx 0/1
-        break;
-      case 1:
-        outputPort(1, PINB);
-        break;
-      case ANALOG_PORT:
-        outputPort(ANALOG_PORT, PINC);
-        break;
-      }
-    }
-  }
-}
-
-// -----------------------------------------------------------------------------
-/* sets the pin mode to the correct state and sets the relevant bits in the
- * two bit-arrays that track Digital I/O and PWM status
- */
-void setPinModeCallback(byte pin, int mode) {
-  byte port = 0;
-  byte offset = 0;
-
-  // TODO: abstract for different boards
-  if (pin < 8) {
-    port = 0;
-    offset = 0;
-  } else if (pin < 14) {
-    port = 1;
-    offset = 8;
-  } else if (pin < 22) {
-    port = 2;
-    offset = 14;
-  }
-  
-  if(pin > 1) { // ignore RxTx (pins 0 and 1)
-    if(pin > 13) 
-      reportAnalogCallback(pin - 14, mode == ANALOG ? 1 : 0); // turn on/off reporting
-    switch(mode) {
-    case ANALOG:
-      digitalWrite(pin, LOW); // disable internal pull-ups and fall thru to 'case INPUT:'
-    case INPUT:
-      pinStatus[pin] = mode;
-      pinMode(pin, INPUT);
-      portStatus[port] = portStatus[port] &~ (1 << (pin - offset));
-      break;
-    case OUTPUT:
-      digitalWrite(pin, LOW); // disable PWM and fall thru to 'case PWM:' 
-    case PWM:
-      pinStatus[pin] = mode;
-      pinMode(pin, OUTPUT);
-      portStatus[port] = portStatus[port] | (1 << (pin - offset));
-      break;
-    case SERVO:
-      if((pin == 9 || pin == 10))
-        pinStatus[pin] = mode;
-      else
-        Firmata.sendString("Servo only on pins 9 and 10");
-      break;
-    case I2C:
-      pinStatus[pin] = mode;
-      Firmata.sendString("I2C mode not yet supported");
-      break;
-    default:
-      Firmata.sendString("Unknown pin mode"); // TODO: put error msgs in EEPROM
-    }
-    // TODO: save status to EEPROM here, if changed
-  }
-}
-
-void analogWriteCallback(byte pin, int value)
-{
-  switch(pinStatus[pin]) {
-  case SERVO:
-    if(pin == 9)  servos[0].write(value);
-    if(pin == 10) servos[1].write(value);
-    break;
-  case PWM:
-    analogWrite(pin, value);
-    break;
-  }
-}
-
-void digitalWriteCallback(byte port, int value)
-{
-  switch(port) {
-  case 0: // pins 2-7 (don't change Rx/Tx, pins 0 and 1)
-    // 0xFF03 == B1111111100000011    0x03 == B00000011
-    PORTD = (value &~ 0xFF03) | (PORTD & 0x03);
-    break;
-  case 1: // pins 8-13 (14,15 are disabled for the crystal) 
-    PORTB = (byte)value;
-    break;
-  case 2: // analog pins used as digital
-    byte pin;
-    byte pinModeMask;
-    for(pin=0; pin<8; pin++)
-      if(pinStatus[pin] == OUTPUT)
-        pinModeMask += 1 << pin;
-    PORTC = (byte)value & pinModeMask;
-    break;
-  }
-}
-
-// -----------------------------------------------------------------------------
-/* sets bits in a bit array (int) to toggle the reporting of the analogIns
- */
-//void FirmataClass::setAnalogPinReporting(byte pin, byte state) {
-//}
-void reportAnalogCallback(byte pin, int value)
-{
-  if(value == 0) {
-    analogInputsToReport = analogInputsToReport &~ (1 << pin);
-  }
-  else { // everything but 0 enables reporting of that pin
-    analogInputsToReport = analogInputsToReport | (1 << pin);
-    setPinModeCallback(pin, ANALOG);
-  }
-  // TODO: save status to EEPROM here, if changed
-}
-
-void reportDigitalCallback(byte port, int value)
-{
-  reportPINs[port] = (byte)value;
-  if(port == ANALOG_PORT) // turn off analog reporting when used as digital
-    analogInputsToReport = 0;
-}
-
-/*==============================================================================
- * SYSEX-BASED commands
- *============================================================================*/
-
-void sysexCallback(byte command, byte argc, byte *argv)
-{
-  switch(command) {
-  case SERVO_CONFIG:
-    if(argc > 4) {
-      // these vars are here for clarity, they'll optimized away by the compiler
-      byte pin = argv[0] - 9; // servos are pins 9 and 10, so offset for array
-      int minPulse = argv[1] + (argv[2] << 7);
-      int maxPulse = argv[3] + (argv[4] << 7);
-      servos[pin].attach(argv[0], minPulse, maxPulse);
-      // TODO does the Servo have to be detach()ed before reconfiguring?
-      setPinModeCallback(pin, SERVO);
-    }
-    break;
-  case SAMPLING_INTERVAL:
-    if (argc > 1)
-      samplingInterval = argv[0] + (argv[1] << 7);
-    else
-      Firmata.sendString("Not enough data");
-    break;
-  }
-}
-
-
-/*==============================================================================
- * SETUP()
- *============================================================================*/
-void setup() 
-{
-  byte i;
-
-  Firmata.setFirmwareVersion(2, 1);
-
-  Firmata.attach(ANALOG_MESSAGE, analogWriteCallback);
-  Firmata.attach(DIGITAL_MESSAGE, digitalWriteCallback);
-  Firmata.attach(REPORT_ANALOG, reportAnalogCallback);
-  Firmata.attach(REPORT_DIGITAL, reportDigitalCallback);
-  Firmata.attach(SET_PIN_MODE, setPinModeCallback);
-  Firmata.attach(START_SYSEX, sysexCallback);
-
-  portStatus[0] = B00000011;  // ignore Tx/RX pins
-  portStatus[1] = B11000000;  // ignore 14/15 pins 
-  portStatus[2] = B00000000;
-
-  for(i=0; i<TOTAL_DIGITAL_PINS; ++i) { // TODO make this work with analogs
-    setPinModeCallback(i,OUTPUT);
-  }
-  // set all outputs to 0 to make sure internal pull-up resistors are off
-  PORTB = 0; // pins 8-15
-  PORTC = 0; // analog port
-  PORTD = 0; // pins 0-7
-
-  // TODO rethink the init, perhaps it should report analog on default
-  for(i=0; i<TOTAL_PORTS; ++i) {
-    reportPINs[i] = false;
-  }
-  // TODO: load state from EEPROM here
-
-  /* send digital inputs here, if enabled, to set the initial state on the
-   * host computer, since once in the loop(), this firmware will only send
-   * digital data on change. */
-  if(reportPINs[0]) outputPort(0, PIND &~ B00000011); // ignore Rx/Tx 0/1
-  if(reportPINs[1]) outputPort(1, PINB);
-  if(reportPINs[ANALOG_PORT]) outputPort(ANALOG_PORT, PINC);
-
-  Firmata.begin(57600);
-}
-
-/*==============================================================================
- * LOOP()
- *============================================================================*/
-void loop() 
-{
-  /* DIGITALREAD - as fast as possible, check for changes and output them to the
-   * FTDI buffer using Serial.print()  */
-  checkDigitalInputs();  
-  currentMillis = millis();
-  if(currentMillis > nextExecuteMillis) {  
-    nextExecuteMillis = currentMillis + samplingInterval;
-    /* SERIALREAD - Serial.read() uses a 128 byte circular buffer, so handle
-     * all serialReads at once, i.e. empty the buffer */
-    while(Firmata.available())
-      Firmata.processInput();
-    /* SEND FTDI WRITE BUFFER - make sure that the FTDI buffer doesn't go over
-     * 60 bytes. use a timer to sending an event character every 4 ms to
-     * trigger the buffer to dump. */
-	
-    /* ANALOGREAD - right after the event character, do all of the
-     * analogReads().  These only need to be done every 4ms. */
-    for(analogPin=0;analogPin<TOTAL_ANALOG_PINS;analogPin++) {
-      if( analogInputsToReport & (1 << analogPin) ) {
-        Firmata.sendAnalog(analogPin, analogRead(analogPin));
-      }
-    }
-  }
-}