Esplora library to new format

9 files changed, 0 insertions, 449 deletions

diff --git a/libraries/Esplora/Beginners/EsploraAccelerometer/EsploraAccelerometer.ino b/libraries/Esplora/Beginners/EsploraAccelerometer/EsploraAccelerometer.ino
deleted file mode 100644
index db5cc93..0000000
--- a/libraries/Esplora/Beginners/EsploraAccelerometer/EsploraAccelerometer.ino
+++ /dev/null
@@ -1,38 +0,0 @@
-/*
-  Esplora Accelerometer 
- 
- This  sketch shows you how to read the values from the accelerometer.
- To see it in action, open the serial monitor and tilt the board. You'll see
- the accelerometer values for each axis change when you tilt the board 
- on that axis.
-  
- Created on 22 Dec 2012
- by Tom Igoe
- 
- This example is in the public domain.
- */
-
-#include <Esplora.h>
-
-void setup()
-{
-  Serial.begin(9600);        // initialize serial communications with your computer
-} 
-
-void loop()
-{
-  int xAxis = Esplora.readAccelerometer(X_AXIS);    // read the X axis
-  int yAxis = Esplora.readAccelerometer(Y_AXIS);    // read the Y axis
-  int zAxis = Esplora.readAccelerometer(Z_AXIS);    // read the Z axis
-
-  Serial.print("x: ");      // print the label for X 
-  Serial.print(xAxis);      // print the value for the X axis
-  Serial.print("\ty: ");    // print a tab character, then the label for Y 
-  Serial.print(yAxis);      // print the value for the Y axis
-  Serial.print("\tz: ");    // print a tab character, then the label for Z
-  Serial.println(zAxis);    // print the value for the Z axis
-
-  delay(500);              // wait half a second (500 milliseconds)
-}
-
-
diff --git a/libraries/Esplora/Beginners/EsploraBlink/EsploraBlink.ino b/libraries/Esplora/Beginners/EsploraBlink/EsploraBlink.ino
deleted file mode 100644
index e198551..0000000
--- a/libraries/Esplora/Beginners/EsploraBlink/EsploraBlink.ino
+++ /dev/null
@@ -1,42 +0,0 @@
-
-/*
-  Esplora Blink
- 
- This  sketch blinks the Esplora's RGB LED. It goes through
- all three primary colors (red, green, blue), then it 
- combines them for secondary colors(yellow, cyan, magenta), then
- it turns on all the colors for white. 
- For best results cover the LED with a piece of white paper to see the colors.
- 
- Created on 22 Dec 2012
- by Tom Igoe
- 
- This example is in the public domain.
- */
-
-#include <Esplora.h>
-
-
-void setup() {
-  // There's nothing to set up for this sketch
-}
-
-void loop() {
-  Esplora.writeRGB(255,0,0);    // make the LED red
-  delay(1000);                  // wait 1 second
-  Esplora.writeRGB(0,255,0);    // make the LED green
-  delay(1000);                  // wait 1 second
-  Esplora.writeRGB(0,0,255);    // make the LED blue
-  delay(1000);                  // wait 1 second
-  Esplora.writeRGB(255,255,0);  // make the LED yellow
-  delay(1000);                  // wait 1 second
-  Esplora.writeRGB(0,255,255);  // make the LED cyan
-  delay(1000);                  // wait 1 second
-  Esplora.writeRGB(255,0,255);  // make the LED magenta
-  delay(1000);                  // wait 1 second
-  Esplora.writeRGB(255,255,255);// make the LED white
-  delay(1000);                  // wait 1 second
-
-}
-
-
diff --git a/libraries/Esplora/Beginners/EsploraJoystickMouse/EsploraJoystickMouse.ino b/libraries/Esplora/Beginners/EsploraJoystickMouse/EsploraJoystickMouse.ino
deleted file mode 100644
index 8d9260e..0000000
--- a/libraries/Esplora/Beginners/EsploraJoystickMouse/EsploraJoystickMouse.ino
+++ /dev/null
@@ -1,50 +0,0 @@
-/*
-  Esplora Joystick Mouse
- 
- This  sketch shows you how to read the joystick and use it to control the movement
- of the cursor on your computer.  You're making your Esplora into a mouse!
- 
- WARNING: this sketch will take over your mouse movement. If you lose control
- of your mouse do the following:
- 1) unplug the Esplora.
- 2) open the EsploraBlink sketch
- 3) hold the reset button down while plugging your Esplora back in
- 4) while holding reset, click "Upload"
- 5) when you see the message "Done compiling", release the reset button.
- 
- This will stop your Esplora from controlling your mouse while you upload a sketch
- that doesn't take control of the mouse.
- 
- Created on 22 Dec 2012
- by Tom Igoe
- 
- This example is in the public domain.
- */
-
-#include <Esplora.h>
-
-void setup()
-{
-  Serial.begin(9600);       // initialize serial communication with your computer
-  Mouse.begin();            // take control of the mouse
-} 
-
-void loop()
-{
-  int xValue = Esplora.readJoystickX();        // read the joystick's X position
-  int yValue = Esplora.readJoystickY();        // read the joystick's Y position
-  int button = Esplora.readJoystickSwitch();   // read the joystick pushbutton
-  Serial.print("Joystick X: ");                // print a label for the X value
-  Serial.print(xValue);                        // print the X value
-  Serial.print("\tY: ");                       // print a tab character and a label for the Y value
-  Serial.print(yValue);                        // print the Y value
-  Serial.print("\tButton: ");                  // print a tab character and a label for the button
-  Serial.print(button);                        // print the button value
-
-  int mouseX = map( xValue,-512, 512, 10, -10);  // map the X value to a range of movement for the mouse X
-  int mouseY = map( yValue,-512, 512, -10, 10);  // map the Y value to a range of movement for the mouse Y
-  Mouse.move(mouseX, mouseY, 0);                 // move the mouse
-  
-  delay(10);                                  // a short delay before moving again
-}
-
diff --git a/libraries/Esplora/Beginners/EsploraLedShow/EsploraLedShow.ino b/libraries/Esplora/Beginners/EsploraLedShow/EsploraLedShow.ino
deleted file mode 100644
index 3c617dc..0000000
--- a/libraries/Esplora/Beginners/EsploraLedShow/EsploraLedShow.ino
+++ /dev/null
@@ -1,42 +0,0 @@
-/*
-  Esplora LED Show
-
-  Makes the RGB LED bright and glow as the joystick or the
-  slider are moved.
-  
-  Created on 22 november 2012
-  By Enrico Gueli <enrico.gueli@gmail.com>
-  Modified 22 Dec 2012
-  by Tom Igoe
-*/
-#include <Esplora.h>
-
-void setup() {
-  // initialize the serial communication:
-  Serial.begin(9600);
-}
-
-void loop() {
-  // read the sensors into variables:
-  int xAxis = Esplora.readJoystickX();
-  int yAxis = Esplora.readJoystickY();
-  int slider = Esplora.readSlider();
-  
-  // convert the sensor readings to light levels:
-  byte red   = map(xAxis, -512, 512, 0, 255);
-  byte green = map(yAxis, -512, 512, 0, 255);
-  byte blue  = slider/4;
- 
-  // print the light levels:
-  Serial.print(red);
-  Serial.print(' ');
-  Serial.print(green);
-  Serial.print(' ');
-  Serial.println(blue);
-
-  // write the light levels to the LED. 
-  Esplora.writeRGB(red, green, blue);
-
-  // add a delay to keep the LED from flickering:  
-  delay(10);
-}
diff --git a/libraries/Esplora/Beginners/EsploraLedShow2/EsploraLedShow2.ino b/libraries/Esplora/Beginners/EsploraLedShow2/EsploraLedShow2.ino
deleted file mode 100644
index 8f9f8a2..0000000
--- a/libraries/Esplora/Beginners/EsploraLedShow2/EsploraLedShow2.ino
+++ /dev/null
@@ -1,55 +0,0 @@
-/*
-  Esplora Led/Microphone
-
-  This simple sketch reads the microphone, light sensor, and slider.
-  Then it uses those readings to set the brightness of red, green and blue
-  channels of the RGB LED. The red channel will change with the loudness
-  "heared" by the microphone, the green channel changes as the
-  amount of light in the room and the blue channel will change
-  with the position of the slider.
-
-  Created on 22 november 2012
-  By Enrico Gueli <enrico.gueli@gmail.com>
-  Modified 24 Nov 2012
-  by Tom Igoe
-*/
-
-#include <Esplora.h>
-
-void setup() {
-  // initialize the serial communication:
-  Serial.begin(9600);
-}
-
-int lowLight = 400;   // the light sensor reading when it's covered
-int highLight = 1023; // the maximum light sensor reading 
-int minGreen = 0;     // minimum brightness of the green LED
-int maxGreen = 100;   // maximum brightness of the green LED
-
-void loop() {
-  // read the sensors into variables:
-  int mic = Esplora.readMicrophone();
-  int light = Esplora.readLightSensor();
-  int slider = Esplora.readSlider();
-  
-  // convert the sensor readings to light levels:
-  byte red   = constrain(mic, 0, 255);
-  byte green = constrain(
-                  map(light, lowLight, highLight, minGreen, maxGreen),
-                  0, 255);
-  byte blue  = slider/4;
-
-  // print the light levels (to see what's going on):
-  Serial.print(red);
-  Serial.print(' ');
-  Serial.print(green);
-  Serial.print(' ');
-  Serial.println(blue);
-
-  // write the light levels to the LED. 
-  // note that the green value is always 0:
-  Esplora.writeRGB(red, green, blue);
-  
-  // add a delay to keep the LED from flickering:
-  delay(10); 
-}
diff --git a/libraries/Esplora/Beginners/EsploraLightCalibrator/EsploraLightCalibrator.ino b/libraries/Esplora/Beginners/EsploraLightCalibrator/EsploraLightCalibrator.ino
deleted file mode 100644
index c3eaff4..0000000
--- a/libraries/Esplora/Beginners/EsploraLightCalibrator/EsploraLightCalibrator.ino
+++ /dev/null
@@ -1,91 +0,0 @@
-/*
-  Esplora Led calibration
- 
- This  sketch shows you how to read and calibrate the light sensor.
- Because light levels vary from one location to another, you need to calibrate the 
- sensor for each location. To do this, you read the sensor for a few seconds,
- and save the highest and lowest readings as maximum and minimum.  
- Then, when you're using the sensor's reading (for example, to set the brightness
- of the LED), you map the sensor's reading to a range between the minimum
- and the maximum.
- 
- Created on 22 Dec 2012
- by Tom Igoe
- 
- This example is in the public domain.
- */
-
-#include <Esplora.h>
-
-// variables:
-int lightMin = 1023;        // minimum sensor value
-int lightMax = 0;           // maximum sensor value
-boolean calibrated = false;  // whether the sensor's been calibrated yet
-
-void setup() {
-  // initialize the serial communication:
-  Serial.begin(9600);
-
-  // print an intial message
-  Serial.println("To calibrate the light sensor, press and hold Switch 1");
-}
-
-void loop() {
-  // if switch 1 is pressed, go to the calibration function again:
-  if (Esplora.readButton(1) == LOW) {
-    calibrate();
-  }
-  // read the sensor into a variable:
-  int light = Esplora.readLightSensor();
-
-  // map the light level to a brightness level for the LED
-  // using the calibration min and max:
-  int brightness = map(light, lightMin, lightMax, 0, 255);
-  // limit the brightness to a range from 0 to 255:
-  brightness = constrain(brightness, 0, 255);
-  // write the brightness to the blue LED. 
-  Esplora.writeBlue(brightness);
-  
-  // if the calibration's been done, show the sensor and brightness
-  // levels in the serial monitor:
-  if (calibrated == true) {
-    // print the light sensor levels and the LED levels (to see what's going on):
-    Serial.print("light sensor level: ");
-    Serial.print(light);
-    Serial.print(" blue brightness: ");
-    Serial.println(brightness);
-  }
-  // add a delay to keep the LED from flickering:
-  delay(10); 
-}
-
-void calibrate() {
-  // tell the user what do to using the serial monitor:
-  Serial.println("While holding switch 1, shine a light on the light sensor, then cover it.");
-
-  // calibrate while switch 1 is pressed:
-  while(Esplora.readButton(1) == LOW) {
-    // read the sensor value: 
-    int light  = Esplora.readLightSensor();
-
-    // record the maximum sensor value:
-    if (light > lightMax) {
-      lightMax = light;
-    }
-
-    // record the minimum sensor value:
-    if (light < lightMin) {
-      lightMin = light;
-    }
-    // note that you're calibrated, for future reference:
-    calibrated = true;
-  }
-}
-
-
-
-
-
-
-
-
diff --git a/libraries/Esplora/Beginners/EsploraMusic/EsploraMusic.ino b/libraries/Esplora/Beginners/EsploraMusic/EsploraMusic.ino
deleted file mode 100644
index 7a950fb..0000000
--- a/libraries/Esplora/Beginners/EsploraMusic/EsploraMusic.ino
+++ /dev/null
@@ -1,53 +0,0 @@
-/*
-  Esplora Music
-
-  This sketch turns the Esplora in a simple musical instrument.
-  Press the Switch 1 and move the slider to see how it works.
-
-  Created on 22 november 2012
-  By Enrico Gueli <enrico.gueli@gmail.com>
-  modified 22 Dec 2012
-  by Tom Igoe
-*/
-
-
-#include <Esplora.h>
-
-// these are the frequencies for the notes from middle C
-// to one octave above middle C:
-const int note[] = {
-262, // C
-277, // C#
-294, // D
-311, // D#
-330, // E
-349, // F
-370, // F#
-392, // G
-415, // G#
-440, // A
-466, // A#
-494, // B
-523  // C next octave
-};
-
-void setup() {
-}
-
-void loop() {
-  // read the button labeled SWITCH_DOWN. If it's low,
-  // then play a note:
-  if (Esplora.readButton(SWITCH_DOWN) == LOW) {
-    int slider = Esplora.readSlider();
-    
-    // use map() to map the slider's range to the 
-    // range of notes you have:
-    byte thisNote = map(slider, 0, 1023, 0, 13);
-    // play the note corresponding to the slider's position:
-    Esplora.tone(note[thisNote]);
-  }
-  else {
-    // if the button isn't pressed, turn the note off:
-    Esplora.noTone();
-  }
-}
diff --git a/libraries/Esplora/Beginners/EsploraSoundSensor/EsploraSoundSensor.ino b/libraries/Esplora/Beginners/EsploraSoundSensor/EsploraSoundSensor.ino
deleted file mode 100644
index 3bf454f..0000000
--- a/libraries/Esplora/Beginners/EsploraSoundSensor/EsploraSoundSensor.ino
+++ /dev/null
@@ -1,41 +0,0 @@
-/*
-  Esplora Sound Sensor
- 
- This  sketch shows you how to read  the microphone sensor. The microphone
-will range from 0 (total silence) to 1023 (really loud).  
- When you're using the sensor's reading (for example, to set the brightness
- of the LED), you map the sensor's reading to a range between the minimum
- and the maximum.
- 
- Created on 22 Dec 2012
- by Tom Igoe
- 
- This example is in the public domain.
- */
-
-#include <Esplora.h>
-
-void setup() {
-  // initialize the serial communication:
-  Serial.begin(9600);
-}
-
-void loop() {
-  // read the sensor into a variable:
-  int loudness = Esplora.readMicrophone();
-
-  // map the sound level to a brightness level for the LED:
-  int brightness = map(loudness, 0, 1023, 0, 255);
-  // write the brightness to the green LED: 
-  Esplora.writeGreen(brightness);
-  
-  
-    // print the microphone levels and the LED levels (to see what's going on):
-    Serial.print("sound level: ");
-    Serial.print(loudness);
-    Serial.print(" Green brightness: ");
-    Serial.println(brightness);
-  // add a delay to keep the LED from flickering:
-  delay(10); 
-}
-
diff --git a/libraries/Esplora/Beginners/EsploraTemperatureSensor/EsploraTemperatureSensor.ino b/libraries/Esplora/Beginners/EsploraTemperatureSensor/EsploraTemperatureSensor.ino
deleted file mode 100644
index 72bbf04..0000000
--- a/libraries/Esplora/Beginners/EsploraTemperatureSensor/EsploraTemperatureSensor.ino
+++ /dev/null
@@ -1,37 +0,0 @@
-/*
-  Esplora Temperature Sensor
- 
- This  sketch shows you how to read the Esplora's temperature sensor
- You can read the temperature sensor in Farhenheit or Celsius.
- 
- Created on 22 Dec 2012
- by Tom Igoe
- 
- This example is in the public domain.
- */
-#include <Esplora.h>
-
-void setup()
-{
-  Serial.begin(9600);      // initialize serial communications with your computer
-} 
-
-void loop()
-{
-  // read the temperature sensor in Celsius, then Fahrenheit:
-  int celsius = Esplora.readTemperature(DEGREES_C);
-  int fahrenheit = Esplora.readTemperature(DEGREES_F);
-
-  // print the results:
-  Serial.print("Temperature is: ");
-  Serial.print(celsius);
-  Serial.print(" degrees Celsius, or ");
-  Serial.print(fahrenheit);
-  Serial.println(" degrees Fahrenheit.");
-  Serial.println("     Fahrenheit = (9/5 * Celsius) + 32");
-
-  // wait a second before reading again:
-  delay(1000);
-}
-
-