Merge of arduino-1.0.1. Work in progress...

1 files changed, 0 insertions, 239 deletions

diff --git a/bootloaders/diskloader/src/DiskLoader.cpp b/bootloaders/diskloader/src/DiskLoader.cpp
deleted file mode 100644
index 6580618..0000000
--- a/bootloaders/diskloader/src/DiskLoader.cpp
+++ /dev/null
@@ -1,239 +0,0 @@
-
-
-#include "Platform.h"
-
-//	This bootloader creates a composite Serial device
-//
-//	The serial interface supports a STK500v1 protocol that is very similar to optiboot
-//
-//	The bootloader will timeout and start the firmware after a few hundred milliseconds
-//	if a usb connection is not detected.
-//	
-//	The tweakier code is to keep the bootloader below 2k (no interrupt table, for example)
-
-extern "C"
-void entrypoint(void) __attribute__ ((naked)) __attribute__ ((section (".vectors")));
-void entrypoint(void)
-{
-	asm volatile (
-		"eor	r1,		r1\n"	// Zero register
-		"out	0x3F,	r1\n"	// SREG
-		"ldi	r28,	0xFF\n"
-		"ldi	r29,	0x0A\n"
-		"out	0x3E,	r29\n"	// SPH
-		"out	0x3D,	r28\n"	// SPL
-		"rjmp	main"			// Stack is all set up, start the main code
-		::);
-}
-
-u8 _flashbuf[128];
-u8 _inSync;
-u8 _ok;
-extern volatile u8 _ejected;
-extern volatile u16 _timeout;
-
-void Program(u8 ep, u16 page, u8 count)
-{
-	u8 write = page < 30*1024;		// Don't write over firmware please
-	if (write)
-		boot_page_erase(page);
-
-	Recv(ep,_flashbuf,count);		// Read while page is erasing
-
-	if (!write)
-		return;
-
-	boot_spm_busy_wait();			// Wait until the memory is erased.
-
-	count >>= 1;
-	u16* p = (u16*)page;
-	u16* b = (u16*)_flashbuf;
-	for (u8 i = 0; i < count; i++)
-		boot_page_fill(p++, b[i]);
-
-    boot_page_write(page);
-    boot_spm_busy_wait();
-    boot_rww_enable ();
-}
-
-
-int USBGetChar();
-#define getch USBGetChar
-
-#define HW_VER	 0x02
-#define SW_MAJOR 0x01
-#define SW_MINOR 0x10
-
-#define STK_OK              0x10
-#define STK_INSYNC          0x14  // ' '
-#define CRC_EOP             0x20  // 'SPACE'
-#define STK_GET_SYNC        0x30  // '0'
-
-#define STK_GET_PARAMETER   0x41  // 'A'
-#define STK_SET_DEVICE      0x42  // 'B'
-#define STK_SET_DEVICE_EXT  0x45  // 'E'
-#define STK_LOAD_ADDRESS    0x55  // 'U'
-#define STK_UNIVERSAL       0x56  // 'V'
-#define STK_PROG_PAGE       0x64  // 'd'
-#define STK_READ_PAGE       0x74  // 't'
-#define STK_READ_SIGN       0x75  // 'u'
-
-extern const u8 _readSize[] PROGMEM;
-const u8 _readSize[] = 
-{
-	STK_GET_PARAMETER,	1,
-	STK_SET_DEVICE,		20,
-	STK_SET_DEVICE_EXT,	5,
-	STK_UNIVERSAL,		4,
-	STK_LOAD_ADDRESS,	2,
-	STK_PROG_PAGE,		3,
-	STK_READ_PAGE,		3,
-	0,0
-};
-
-extern const u8 _consts[] PROGMEM;
-const u8 _consts[] = 
-{
-	SIGNATURE_0,
-	SIGNATURE_1,
-	SIGNATURE_2,
-	HW_VER,		// Hardware version
-	SW_MAJOR,	// Software major version
-	SW_MINOR,	// Software minor version
-	0x03,		// Unknown but seems to be required by avr studio 3.56
-	0x00,		// 
-};
-
-
-void USBInit(void);
-int main(void) __attribute__ ((naked));
-
-//	STK500v1 main loop, very similar to optiboot in protocol and implementation
-int main()
-{
-	wdt_disable();
-	TXLED0;
-	RXLED0;
-	LED0;
-	BOARD_INIT();
-	USBInit();
-
-	_inSync = STK_INSYNC;
-	_ok = STK_OK;
-
-	if (pgm_read_word(0) != -1)
-		_ejected = 1;
-
-	for(;;)
-	{
-		u8* packet = _flashbuf;
-		u16 address = 0;
-		for (;;)
-		{
-			u8 cmd = getch();
-
-			//	Read packet contents
-			u8 len;
-			const u8* rs = _readSize;
-			for(;;)
-			{
-				u8 c = pgm_read_byte(rs++);
-				len = pgm_read_byte(rs++);
-				if (c == cmd || c == 0)
-					break;
-			}
-			_timeout = 0;
-			//	Read params
-			Recv(CDC_RX,packet,len);
-
-			//	Send a response
-			u8 send = 0;
-			const u8* pgm = _consts+7;			// 0
-			if (STK_GET_PARAMETER == cmd)
-			{
-				u8 i = packet[0] - 0x80;
-				if (i > 2)
-					i = (i == 0x18) ? 3 : 4;	// 0x80:HW_VER,0x81:SW_MAJOR,0x82:SW_MINOR,0x18:3 or 0
-				pgm = _consts + i + 3;
-				send = 1;
-			}
-
-			else if (STK_UNIVERSAL == cmd)
-			{
-				if (packet[0] == 0x30)
-					pgm = _consts + packet[2];	// read signature
-				send = 1;
-			}
-			
-			//	Read signature bytes
-			else if (STK_READ_SIGN == cmd)
-			{
-				pgm = _consts;
-				send = 3;
-			}
-
-			else if (STK_LOAD_ADDRESS == cmd)
-			{
-				address = *((u16*)packet);		// word addresses
-				address += address;
-			}
-
-			else if (STK_PROG_PAGE == cmd)
-			{
-				Program(CDC_RX,address,packet[1]);
-			}
-
-			else if (STK_READ_PAGE == cmd)
-			{
-				send = packet[1];
-				pgm = (const u8*)address;
-				address += send; // not sure of this is required
-			}
-
-			// Check sync
-			if (getch() != ' ')
-				break;
-			Transfer(CDC_TX,&_inSync,1);
-
-			// Send result
-			if (send)
-				Transfer(CDC_TX|TRANSFER_PGM,pgm,send);	// All from pgm memory
-
-			//	Send ok
-			Transfer(CDC_TX|TRANSFER_RELEASE,&_ok,1);
-
-			if (cmd == 'Q')
-				break;
-		}
-		_timeout = 500;		// wait a moment before exiting the bootloader - may need to finish responding to 'Q' for example
-		_ejected = 1;
-	}
-}
-
-//	Nice breathing LED indicates we are in the firmware
-u16 _pulse;
-void LEDPulse()
-{
-	_pulse += 4;
-	u8 p = _pulse >> 9;
-	if (p > 63)
-		p = 127-p;
-	p += p;
-	if (((u8)_pulse) > p)
-		LED0;
-	else
-		LED1;
-}
-
-void Reboot()
-{
-	TXLED0;		// switch off the RX and TX LEDs before starting the user sketch
-	RXLED0;
-	UDCON = 1;		// Detatch USB
-	UDIEN = 0;
-	asm volatile (	// Reset vector to run firmware
-		"clr r30\n"
-		"clr r31\n"
-		"ijmp\n"
-	::);
-}