/**********************************************************/ /* Serial Bootloader for Atmel megaAVR Controllers */ /* */ /* tested with ATmega8, ATmega128 and ATmega168 */ /* should work with other mega's, see code for details */ /* */ /* ATmegaBOOT.c */ /* */ /* build: 050815 */ /* date : 15.08.2005 */ /* */ /* 20060802: hacked for Arduino by D. Cuartielles */ /* based on a previous hack by D. Mellis */ /* and D. Cuartielles */ /* */ /* Monitor and debug functions were added to the original */ /* code by Dr. Erik Lins, chip45.com. (See below) */ /* */ /* Thanks to Karl Pitrich for fixing a bootloader pin */ /* problem and more informative LED blinking! */ /* */ /* For the latest version see: */ /* http://www.chip45.com/ */ /* */ /* ------------------------------------------------------ */ /* */ /* based on stk500boot.c */ /* Copyright (c) 2003, Jason P. Kyle */ /* All rights reserved. */ /* see avr1.org for original file and information */ /* */ /* This program is free software; you can redistribute it */ /* and/or modify it under the terms of the GNU General */ /* Public License as published by the Free Software */ /* Foundation; either version 2 of the License, or */ /* (at your option) any later version. */ /* */ /* This program is distributed in the hope that it will */ /* be useful, but WITHOUT ANY WARRANTY; without even the */ /* implied warranty of MERCHANTABILITY or FITNESS FOR A */ /* PARTICULAR PURPOSE. See the GNU General Public */ /* License for more details. */ /* */ /* You should have received a copy of the GNU General */ /* Public License along with this program; if not, write */ /* to the Free Software Foundation, Inc., */ /* 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ /* */ /* Licence can be viewed at */ /* http://www.fsf.org/licenses/gpl.txt */ /* */ /* Target = Atmel AVR m128,m64,m32,m16,m8,m162,m163,m169, */ /* m8515,m8535. ATmega161 has a very small boot block so */ /* isn't supported. */ /* */ /* Tested with m128,m8,m163 - feel free to let me know */ /* how/if it works for you. */ /* */ /**********************************************************/ /* some includes */ #include #include #include #include #include #define set_output(sfr, bit) (_SFR_BYTE(sfr) |= _BV(bit)) #define set_input(sfr, bit) (_SFR_BYTE(sfr) &= ~_BV(bit)) #define high(sfr, bit) (_SFR_BYTE(sfr) |= _BV(bit)) #define low(sfr, bit) (_SFR_BYTE(sfr) &= ~_BV(bit)) /* the current avr-libc eeprom functions do not support the ATmega168 */ /* own eeprom write/read functions are used instead */ #if !defined(__AVR_ATmega168__) || !defined(__AVR_ATmega328P__) || !defined(__AVR_ATmega328__) #include #endif /* define F_CPU according to AVR_FREQ set in Makefile */ /* Is there a better way to pass such a parameter from Makefile to source code ? */ #define F_CPU 16000000L #include /* 20060803: hacked by DojoCorp */ /* set the waiting time for the bootloader */ #define MAX_TIME_COUNT (F_CPU>>1) /* set the UART baud rate */ /* 20060803: hacked by DojoCorp */ #define BAUD_RATE 115200 /* SW_MAJOR and MINOR needs to be updated from time to time to avoid warning message from AVR Studio */ /* never allow AVR Studio to do an update !!!! */ #define HW_VER 0x02 #define SW_MAJOR 0x01 #define SW_MINOR 0x0f /* Adjust to suit whatever pin your hardware uses to enter the bootloader */ /* ATmega128 has two UARTS so two pins are used to enter bootloader and select UART */ /* BL0... means UART0, BL1... means UART1 */ #ifdef __AVR_ATmega128__ #define BL_DDR DDRF #define BL_PORT PORTF #define BL_PIN PINF #define BL0 PINF7 #define BL1 PINF6 #else /* other ATmegas have only one UART, so only one pin is defined to enter bootloader */ #define BL_DDR DDRD #define BL_PORT PORTD #define BL_PIN PIND #define BL PIND6 #endif /* onboard LED is used to indicate, that the bootloader was entered (3x flashing) */ /* if monitor functions are included, LED goes on after monitor was entered */ #ifdef __AVR_ATmega128__ /* Onboard LED is connected to pin PB7 (e.g. Crumb128, PROBOmega128, Savvy128) */ #define LED_DDR DDRB #define LED_PORT PORTB #define LED_PIN PINB #define LED PINB7 #else /* Onboard LED is connected to pin PB2 (e.g. Crumb8, Crumb168) */ #define LED_DDR DDRB #define LED_PORT PORTB #define LED_PIN PINB /* 20060803: hacked by DojoCorp, LED pin is B5 in Arduino */ /* #define LED PINB2 */ #define LED PINB5 #endif /* monitor functions will only be compiled when using ATmega128, due to bootblock size constraints */ #ifdef __AVR_ATmega128__ #define MONITOR #endif /* define various device id's */ /* manufacturer byte is always the same */ #define SIG1 0x1E // Yep, Atmel is the only manufacturer of AVR micros. Single source :( #if defined __AVR_ATmega128__ #define SIG2 0x97 #define SIG3 0x02 #define PAGE_SIZE 0x80U //128 words #elif defined __AVR_ATmega64__ #define SIG2 0x96 #define SIG3 0x02 #define PAGE_SIZE 0x80U //128 words #elif defined __AVR_ATmega32__ #define SIG2 0x95 #define SIG3 0x02 #define PAGE_SIZE 0x40U //64 words #elif defined __AVR_ATmega16__ #define SIG2 0x94 #define SIG3 0x03 #define PAGE_SIZE 0x40U //64 words #elif defined __AVR_ATmega8__ #define SIG2 0x93 #define SIG3 0x07 #define PAGE_SIZE 0x20U //32 words #elif defined __AVR_ATmega88__ #define SIG2 0x93 #define SIG3 0x0a #define PAGE_SIZE 0x20U //32 words #elif defined __AVR_ATmega168__ #define SIG2 0x94 #define SIG3 0x06 #define PAGE_SIZE 0x40U //64 words #elif defined __AVR_ATmega328P__ #define SIG2 0x95 #define SIG3 0x0F #define PAGE_SIZE 0x40U //64 words #elif defined __AVR_ATmega328__ #define SIG2 0x95 #define SIG3 0x14 #define PAGE_SIZE 0x40U //64 words #elif defined __AVR_ATmega162__ #define SIG2 0x94 #define SIG3 0x04 #define PAGE_SIZE 0x40U //64 words #elif defined __AVR_ATmega163__ #define SIG2 0x94 #define SIG3 0x02 #define PAGE_SIZE 0x40U //64 words #elif defined __AVR_ATmega169__ #define SIG2 0x94 #define SIG3 0x05 #define PAGE_SIZE 0x40U //64 words #elif defined __AVR_ATmega8515__ #define SIG2 0x93 #define SIG3 0x06 #define PAGE_SIZE 0x20U //32 words #elif defined __AVR_ATmega8535__ #define SIG2 0x93 #define SIG3 0x08 #define PAGE_SIZE 0x20U //32 words #endif /* function prototypes */ void putch(char); char getch(void); void getNch(uint8_t); void byte_response(uint8_t); void nothing_response(void); char gethex(void); void puthex(char); void flash_led(uint8_t); /* some variables */ union address_union { uint16_t word; uint8_t byte[2]; } address; union length_union { uint16_t word; uint8_t byte[2]; } length; struct flags_struct { unsigned eeprom : 1; unsigned rampz : 1; } flags; uint8_t buff[256]; uint8_t address_high; uint8_t pagesz=0x80; uint8_t i; uint8_t bootuart = 0; void (*app_start)(void) = 0x0000; /* main program starts here */ int main(void) { uint8_t ch,ch2; uint16_t w; asm volatile("nop\n\t"); /* set pin direction for bootloader pin and enable pullup */ /* for ATmega128, two pins need to be initialized */ #ifdef __AVR_ATmega128__ BL_DDR &= ~_BV(BL0); BL_DDR &= ~_BV(BL1); BL_PORT |= _BV(BL0); BL_PORT |= _BV(BL1); #else BL_DDR &= ~_BV(BL); BL_PORT |= _BV(BL); #endif #ifdef __AVR_ATmega128__ /* check which UART should be used for booting */ if(bit_is_clear(BL_PIN, BL0)) { bootuart = 1; } else if(bit_is_clear(BL_PIN, BL1)) { bootuart = 2; } #endif /* check if flash is programmed already, if not start bootloader anyway */ if(pgm_read_byte_near(0x0000) != 0xFF) { #ifdef __AVR_ATmega128__ /* no UART was selected, start application */ if(!bootuart) { app_start(); } #else /* check if bootloader pin is set low */ /* we don't start this part neither for the m8, nor m168 */ //if(bit_is_set(BL_PIN, BL)) { // app_start(); // } #endif } #ifdef __AVR_ATmega128__ /* no bootuart was selected, default to uart 0 */ if(!bootuart) { bootuart = 1; } #endif /* initialize UART(s) depending on CPU defined */ #ifdef __AVR_ATmega128__ if(bootuart == 1) { UBRR0L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1); UBRR0H = (F_CPU/(BAUD_RATE*16L)-1) >> 8; UCSR0A = 0x00; UCSR0C = 0x06; UCSR0B = _BV(TXEN0)|_BV(RXEN0); } if(bootuart == 2) { UBRR1L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1); UBRR1H = (F_CPU/(BAUD_RATE*16L)-1) >> 8; UCSR1A = 0x00; UCSR1C = 0x06; UCSR1B = _BV(TXEN1)|_BV(RXEN1); } #elif defined __AVR_ATmega163__ UBRR = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1); UBRRHI = (F_CPU/(BAUD_RATE*16L)-1) >> 8; UCSRA = 0x00; UCSRB = _BV(TXEN)|_BV(RXEN); #elif defined(__AVR_ATmega168__) || defined(__AVR_ATmega328P__) || defined(__AVR_ATmega328__) UBRR0H = ((F_CPU / 16 + BAUD_RATE / 2) / BAUD_RATE - 1) >> 8; UBRR0L = ((F_CPU / 16 + BAUD_RATE / 2) / BAUD_RATE - 1); //UBRR0L = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1); //UBRR0H = (F_CPU/(BAUD_RATE*16L)-1) >> 8; UCSR0B = (1<>8; // set baud rate UBRRL = (((F_CPU/BAUD_RATE)/16)-1); UCSRB = (1<> 8; UCSRA = 0x00; UCSRC = 0x06; UCSRB = _BV(TXEN)|_BV(RXEN); #endif /* set LED pin as output */ LED_DDR |= _BV(LED); set_output(DDRD,PIND7); high(PORTD,PD7); for (i = 0; i < 16; i++) { _delay_loop_2(0); } low(PORTD,PD7); /* flash onboard LED to signal entering of bootloader */ #ifdef __AVR_ATmega128__ // 4x for UART0, 5x for UART1 flash_led(3 + bootuart); #else flash_led(3); #endif /* 20050803: by DojoCorp, this is one of the parts provoking the system to stop listening, cancelled from the original */ //putch('\0'); //message("SET BT PAGEMODE 3 2000 1"); putch('S'); putch('E'); putch('T'); putch(' '); putch('B'); putch('T'); putch(' '); putch('P'); putch('A'); putch('G'); putch('E'); putch('M'); putch('O'); putch('D'); putch('E'); putch(' '); putch('3'); putch(' '); putch('2'); putch('0'); putch('0'); putch('0'); putch(' '); putch('1'); putch(0x0D); //put_s("SET BT ROLE 0 f 7d00"); putch('S'); putch('E'); putch('T'); putch(' '); putch('B'); putch('T'); putch(' '); putch('R'); putch('O'); putch('L'); putch('E'); putch(' '); putch('0'); putch(' '); putch('f'); putch(' '); putch('7'); putch('d'); putch('0'); putch('0'); putch(0x0D); /* forever loop */ for (;;) { /* get character from UART */ ch = getch(); /* A bunch of if...else if... gives smaller code than switch...case ! */ /* Hello is anyone home ? */ if(ch=='0') { nothing_response(); } /* Request programmer ID */ /* Not using PROGMEM string due to boot block in m128 being beyond 64kB boundry */ /* Would need to selectively manipulate RAMPZ, and it's only 9 characters anyway so who cares. */ else if(ch=='1') { if (getch() == ' ') { putch(0x14); putch('A'); putch('V'); putch('R'); putch(' '); putch('I'); putch('S'); putch('P'); putch(0x10); } } /* AVR ISP/STK500 board commands DON'T CARE so default nothing_response */ else if(ch=='@') { ch2 = getch(); if (ch2>0x85) getch(); nothing_response(); } /* AVR ISP/STK500 board requests */ else if(ch=='A') { ch2 = getch(); if(ch2==0x80) byte_response(HW_VER); // Hardware version else if(ch2==0x81) byte_response(SW_MAJOR); // Software major version else if(ch2==0x82) byte_response(SW_MINOR); // Software minor version else if(ch2==0x98) byte_response(0x03); // Unknown but seems to be required by avr studio 3.56 else byte_response(0x00); // Covers various unnecessary responses we don't care about } /* Device Parameters DON'T CARE, DEVICE IS FIXED */ else if(ch=='B') { getNch(20); nothing_response(); } /* Parallel programming stuff DON'T CARE */ else if(ch=='E') { getNch(5); nothing_response(); } /* Enter programming mode */ else if(ch=='P') { nothing_response(); } /* Leave programming mode */ else if(ch=='Q') { nothing_response(); } /* Erase device, don't care as we will erase one page at a time anyway. */ else if(ch=='R') { nothing_response(); } /* Set address, little endian. EEPROM in bytes, FLASH in words */ /* Perhaps extra address bytes may be added in future to support > 128kB FLASH. */ /* This might explain why little endian was used here, big endian used everywhere else. */ else if(ch=='U') { address.byte[0] = getch(); address.byte[1] = getch(); nothing_response(); } /* Universal SPI programming command, disabled. Would be used for fuses and lock bits. */ else if(ch=='V') { getNch(4); byte_response(0x00); } /* Write memory, length is big endian and is in bytes */ else if(ch=='d') { length.byte[1] = getch(); length.byte[0] = getch(); flags.eeprom = 0; if (getch() == 'E') flags.eeprom = 1; for (w=0;w127) address_high = 0x01; //Only possible with m128, m256 will need 3rd address byte. FIXME else address_high = 0x00; #ifdef __AVR_ATmega128__ RAMPZ = address_high; #endif address.word = address.word << 1; //address * 2 -> byte location /* if ((length.byte[0] & 0x01) == 0x01) length.word++; //Even up an odd number of bytes */ if ((length.byte[0] & 0x01)) length.word++; //Even up an odd number of bytes cli(); //Disable interrupts, just to be sure // HACKME: EEPE used to be EEWE while(bit_is_set(EECR,EEPE)); //Wait for previous EEPROM writes to complete asm volatile( "clr r17 \n\t" //page_word_count "lds r30,address \n\t" //Address of FLASH location (in bytes) "lds r31,address+1 \n\t" "ldi r28,lo8(buff) \n\t" //Start of buffer array in RAM "ldi r29,hi8(buff) \n\t" "lds r24,length \n\t" //Length of data to be written (in bytes) "lds r25,length+1 \n\t" "length_loop: \n\t" //Main loop, repeat for number of words in block "cpi r17,0x00 \n\t" //If page_word_count=0 then erase page "brne no_page_erase \n\t" "wait_spm1: \n\t" "lds r16,%0 \n\t" //Wait for previous spm to complete "andi r16,1 \n\t" "cpi r16,1 \n\t" "breq wait_spm1 \n\t" "ldi r16,0x03 \n\t" //Erase page pointed to by Z "sts %0,r16 \n\t" "spm \n\t" #ifdef __AVR_ATmega163__ ".word 0xFFFF \n\t" "nop \n\t" #endif "wait_spm2: \n\t" "lds r16,%0 \n\t" //Wait for previous spm to complete "andi r16,1 \n\t" "cpi r16,1 \n\t" "breq wait_spm2 \n\t" "ldi r16,0x11 \n\t" //Re-enable RWW section "sts %0,r16 \n\t" "spm \n\t" #ifdef __AVR_ATmega163__ ".word 0xFFFF \n\t" "nop \n\t" #endif "no_page_erase: \n\t" "ld r0,Y+ \n\t" //Write 2 bytes into page buffer "ld r1,Y+ \n\t" "wait_spm3: \n\t" "lds r16,%0 \n\t" //Wait for previous spm to complete "andi r16,1 \n\t" "cpi r16,1 \n\t" "breq wait_spm3 \n\t" "ldi r16,0x01 \n\t" //Load r0,r1 into FLASH page buffer "sts %0,r16 \n\t" "spm \n\t" "inc r17 \n\t" //page_word_count++ "cpi r17,%1 \n\t" "brlo same_page \n\t" //Still same page in FLASH "write_page: \n\t" "clr r17 \n\t" //New page, write current one first "wait_spm4: \n\t" "lds r16,%0 \n\t" //Wait for previous spm to complete "andi r16,1 \n\t" "cpi r16,1 \n\t" "breq wait_spm4 \n\t" #ifdef __AVR_ATmega163__ "andi r30,0x80 \n\t" // m163 requires Z6:Z1 to be zero during page write #endif "ldi r16,0x05 \n\t" //Write page pointed to by Z "sts %0,r16 \n\t" "spm \n\t" #ifdef __AVR_ATmega163__ ".word 0xFFFF \n\t" "nop \n\t" "ori r30,0x7E \n\t" // recover Z6:Z1 state after page write (had to be zero during write) #endif "wait_spm5: \n\t" "lds r16,%0 \n\t" //Wait for previous spm to complete "andi r16,1 \n\t" "cpi r16,1 \n\t" "breq wait_spm5 \n\t" "ldi r16,0x11 \n\t" //Re-enable RWW section "sts %0,r16 \n\t" "spm \n\t" #ifdef __AVR_ATmega163__ ".word 0xFFFF \n\t" "nop \n\t" #endif "same_page: \n\t" "adiw r30,2 \n\t" //Next word in FLASH "sbiw r24,2 \n\t" //length-2 "breq final_write \n\t" //Finished "rjmp length_loop \n\t" "final_write: \n\t" "cpi r17,0 \n\t" "breq block_done \n\t" "adiw r24,2 \n\t" //length+2, fool above check on length after short page write "rjmp write_page \n\t" "block_done: \n\t" "clr __zero_reg__ \n\t" //restore zero register #if defined __AVR_ATmega168__ || __AVR_ATmega328P__ || __AVR_ATmega_328__ : "=m" (SPMCSR) : "M" (PAGE_SIZE) : "r0","r16","r17","r24","r25","r28","r29","r30","r31" #else : "=m" (SPMCR) : "M" (PAGE_SIZE) : "r0","r16","r17","r24","r25","r28","r29","r30","r31" #endif ); /* Should really add a wait for RWW section to be enabled, don't actually need it since we never */ /* exit the bootloader without a power cycle anyhow */ } putch(0x14); putch(0x10); } } /* Read memory block mode, length is big endian. */ else if(ch=='t') { length.byte[1] = getch(); length.byte[0] = getch(); #if defined __AVR_ATmega128__ if (address.word>0x7FFF) flags.rampz = 1; // No go with m256, FIXME else flags.rampz = 0; #endif if (getch() == 'E') flags.eeprom = 1; else { flags.eeprom = 0; address.word = address.word << 1; // address * 2 -> byte location } if (getch() == ' ') { // Command terminator putch(0x14); for (w=0;w < length.word;w++) { // Can handle odd and even lengths okay if (flags.eeprom) { // Byte access EEPROM read #if defined __AVR_ATmega168__ || __AVR_ATmega328P__ || __AVR_ATmega328__ while(EECR & (1<= 'a') { ah = ah - 'a' + 0x0a; } else if(ah >= '0') { ah -= '0'; } if(al >= 'a') { al = al - 'a' + 0x0a; } else if(al >= '0') { al -= '0'; } return (ah << 4) + al; } void puthex(char ch) { char ah,al; ah = (ch & 0xf0) >> 4; if(ah >= 0x0a) { ah = ah - 0x0a + 'a'; } else { ah += '0'; } al = (ch & 0x0f); if(al >= 0x0a) { al = al - 0x0a + 'a'; } else { al += '0'; } putch(ah); putch(al); } void putch(char ch) { #ifdef __AVR_ATmega128__ if(bootuart == 1) { while (!(UCSR0A & _BV(UDRE0))); UDR0 = ch; } else if (bootuart == 2) { while (!(UCSR1A & _BV(UDRE1))); UDR1 = ch; } #elif defined (__AVR_ATmega168__) || defined(__AVR_ATmega328P__) || defined(__AVR_ATmega328__) while (!(UCSR0A & _BV(UDRE0))); UDR0 = ch; #else /* m8,16,32,169,8515,8535,163 */ while (!(UCSRA & _BV(UDRE))); UDR = ch; #endif } char getch(void) { #ifdef __AVR_ATmega128__ if(bootuart == 1) { while(!(UCSR0A & _BV(RXC0))); return UDR0; } else if(bootuart == 2) { while(!(UCSR1A & _BV(RXC1))); return UDR1; } return 0; #elif defined (__AVR_ATmega168__) || defined(__AVR_ATmega328P__) || defined(__AVR_ATmega328__) uint32_t count = 0; while(!(UCSR0A & _BV(RXC0))){ /* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/ /* HACKME:: here is a good place to count times*/ count++; if (count > MAX_TIME_COUNT) app_start(); } return UDR0; #else /* m8,16,32,169,8515,8535,163 */ uint32_t count = 0; while(!(UCSRA & _BV(RXC))){ /* 20060803 DojoCorp:: Addon coming from the previous Bootloader*/ /* HACKME:: here is a good place to count times*/ count++; if (count > MAX_TIME_COUNT) app_start(); } return UDR; #endif } void getNch(uint8_t count) { uint8_t i; for(i=0;i