From 0887b98f627500271b5ad8b3c4f6c7b90bc227ee Mon Sep 17 00:00:00 2001 From: Thibaut VIARD Date: Tue, 21 Jun 2011 00:20:43 +0200 Subject: Moving all AVR specific libraries to hardware/avr --- .../examples/StandardFirmata/StandardFirmata.pde | 398 +++++++++++++++++++++ 1 file changed, 398 insertions(+) create mode 100644 libraries/Firmata/examples/StandardFirmata/StandardFirmata.pde (limited to 'libraries/Firmata/examples/StandardFirmata/StandardFirmata.pde') diff --git a/libraries/Firmata/examples/StandardFirmata/StandardFirmata.pde b/libraries/Firmata/examples/StandardFirmata/StandardFirmata.pde new file mode 100644 index 0000000..cd43366 --- /dev/null +++ b/libraries/Firmata/examples/StandardFirmata/StandardFirmata.pde @@ -0,0 +1,398 @@ +/* + Copyright (C) 2006-2008 Hans-Christoph Steiner. All rights reserved. + + This library is free software; you can redistribute it and/or + modify it under the terms of the GNU Lesser General Public + License as published by the Free Software Foundation; either + version 2.1 of the License, or (at your option) any later version. + + See file LICENSE.txt for further informations on licensing terms. + + formatted using the GNU C formatting and indenting +*/ + +/* + * TODO: use Program Control to load stored profiles from EEPROM + */ + +#include +#include + +/*============================================================================== + * GLOBAL VARIABLES + *============================================================================*/ + +/* analog inputs */ +int analogInputsToReport = 0; // bitwise array to store pin reporting + +/* digital input ports */ +byte reportPINs[TOTAL_PORTS]; // 1 = report this port, 0 = silence +byte previousPINs[TOTAL_PORTS]; // previous 8 bits sent + +/* pins configuration */ +byte pinConfig[TOTAL_PINS]; // configuration of every pin +byte portConfigInputs[TOTAL_PORTS]; // each bit: 1 = pin in INPUT, 0 = anything else +int pinState[TOTAL_PINS]; // any value that has been written + +/* timer variables */ +unsigned long currentMillis; // store the current value from millis() +unsigned long previousMillis; // for comparison with currentMillis +int samplingInterval = 19; // how often to run the main loop (in ms) + +Servo servos[MAX_SERVOS]; + +/*============================================================================== + * FUNCTIONS + *============================================================================*/ + +void outputPort(byte portNumber, byte portValue, byte forceSend) +{ + // pins not configured as INPUT are cleared to zeros + portValue = portValue & portConfigInputs[portNumber]; + // only send if the value is different than previously sent + if(forceSend || previousPINs[portNumber] != portValue) { + Firmata.sendDigitalPort(portNumber, portValue); + previousPINs[portNumber] = portValue; + } +} + +/* ----------------------------------------------------------------------------- + * check all the active digital inputs for change of state, then add any events + * to the Serial output queue using Serial.print() */ +void checkDigitalInputs(void) +{ + /* Using non-looping code allows constants to be given to readPort(). + * The compiler will apply substantial optimizations if the inputs + * to readPort() are compile-time constants. */ + if (TOTAL_PORTS > 0 && reportPINs[0]) outputPort(0, readPort(0, portConfigInputs[0]), false); + if (TOTAL_PORTS > 1 && reportPINs[1]) outputPort(1, readPort(1, portConfigInputs[1]), false); + if (TOTAL_PORTS > 2 && reportPINs[2]) outputPort(2, readPort(2, portConfigInputs[2]), false); + if (TOTAL_PORTS > 3 && reportPINs[3]) outputPort(3, readPort(3, portConfigInputs[3]), false); + if (TOTAL_PORTS > 4 && reportPINs[4]) outputPort(4, readPort(4, portConfigInputs[4]), false); + if (TOTAL_PORTS > 5 && reportPINs[5]) outputPort(5, readPort(5, portConfigInputs[5]), false); + if (TOTAL_PORTS > 6 && reportPINs[6]) outputPort(6, readPort(6, portConfigInputs[6]), false); + if (TOTAL_PORTS > 7 && reportPINs[7]) outputPort(7, readPort(7, portConfigInputs[7]), false); + if (TOTAL_PORTS > 8 && reportPINs[8]) outputPort(8, readPort(8, portConfigInputs[8]), false); + if (TOTAL_PORTS > 9 && reportPINs[9]) outputPort(9, readPort(9, portConfigInputs[9]), false); + if (TOTAL_PORTS > 10 && reportPINs[10]) outputPort(10, readPort(10, portConfigInputs[10]), false); + if (TOTAL_PORTS > 11 && reportPINs[11]) outputPort(11, readPort(11, portConfigInputs[11]), false); + if (TOTAL_PORTS > 12 && reportPINs[12]) outputPort(12, readPort(12, portConfigInputs[12]), false); + if (TOTAL_PORTS > 13 && reportPINs[13]) outputPort(13, readPort(13, portConfigInputs[13]), false); + if (TOTAL_PORTS > 14 && reportPINs[14]) outputPort(14, readPort(14, portConfigInputs[14]), false); + if (TOTAL_PORTS > 15 && reportPINs[15]) outputPort(15, readPort(15, portConfigInputs[15]), false); +} + +// ----------------------------------------------------------------------------- +/* sets the pin mode to the correct state and sets the relevant bits in the + * two bit-arrays that track Digital I/O and PWM status + */ +void setPinModeCallback(byte pin, int mode) +{ + if (IS_PIN_SERVO(pin) && mode != SERVO && servos[PIN_TO_SERVO(pin)].attached()) { + servos[PIN_TO_SERVO(pin)].detach(); + } + if (IS_PIN_ANALOG(pin)) { + reportAnalogCallback(PIN_TO_ANALOG(pin), mode == ANALOG ? 1 : 0); // turn on/off reporting + } + if (IS_PIN_DIGITAL(pin)) { + if (mode == INPUT) { + portConfigInputs[pin/8] |= (1 << (pin & 7)); + } else { + portConfigInputs[pin/8] &= ~(1 << (pin & 7)); + } + } + pinState[pin] = 0; + switch(mode) { + case ANALOG: + if (IS_PIN_ANALOG(pin)) { + if (IS_PIN_DIGITAL(pin)) { + pinMode(PIN_TO_DIGITAL(pin), INPUT); // disable output driver + digitalWrite(PIN_TO_DIGITAL(pin), LOW); // disable internal pull-ups + } + pinConfig[pin] = ANALOG; + } + break; + case INPUT: + if (IS_PIN_DIGITAL(pin)) { + pinMode(PIN_TO_DIGITAL(pin), INPUT); // disable output driver + digitalWrite(PIN_TO_DIGITAL(pin), LOW); // disable internal pull-ups + pinConfig[pin] = INPUT; + } + break; + case OUTPUT: + if (IS_PIN_DIGITAL(pin)) { + digitalWrite(PIN_TO_DIGITAL(pin), LOW); // disable PWM + pinMode(PIN_TO_DIGITAL(pin), OUTPUT); + pinConfig[pin] = OUTPUT; + } + break; + case PWM: + if (IS_PIN_PWM(pin)) { + pinMode(PIN_TO_PWM(pin), OUTPUT); + analogWrite(PIN_TO_PWM(pin), 0); + pinConfig[pin] = PWM; + } + break; + case SERVO: + if (IS_PIN_SERVO(pin)) { + pinConfig[pin] = SERVO; + if (!servos[PIN_TO_SERVO(pin)].attached()) { + servos[PIN_TO_SERVO(pin)].attach(PIN_TO_DIGITAL(pin)); + } else { + Firmata.sendString("Servo only on pins from 2 to 13"); + } + } + break; + case I2C: + pinConfig[pin] = mode; + Firmata.sendString("I2C mode not yet supported"); + break; + default: + Firmata.sendString("Unknown pin mode"); // TODO: put error msgs in EEPROM + } + // TODO: save status to EEPROM here, if changed +} + +void analogWriteCallback(byte pin, int value) +{ + if (pin < TOTAL_PINS) { + switch(pinConfig[pin]) { + case SERVO: + if (IS_PIN_SERVO(pin)) + servos[PIN_TO_SERVO(pin)].write(value); + pinState[pin] = value; + break; + case PWM: + if (IS_PIN_PWM(pin)) + analogWrite(PIN_TO_PWM(pin), value); + pinState[pin] = value; + break; + } + } +} + +void digitalWriteCallback(byte port, int value) +{ + byte pin, lastPin, mask=1, pinWriteMask=0; + + if (port < TOTAL_PORTS) { + // create a mask of the pins on this port that are writable. + lastPin = port*8+8; + if (lastPin > TOTAL_PINS) lastPin = TOTAL_PINS; + for (pin=port*8; pin < lastPin; pin++) { + // do not disturb non-digital pins (eg, Rx & Tx) + if (IS_PIN_DIGITAL(pin)) { + // only write to OUTPUT and INPUT (enables pullup) + // do not touch pins in PWM, ANALOG, SERVO or other modes + if (pinConfig[pin] == OUTPUT || pinConfig[pin] == INPUT) { + pinWriteMask |= mask; + pinState[pin] = ((byte)value & mask) ? 1 : 0; + } + } + mask = mask << 1; + } + writePort(port, (byte)value, pinWriteMask); + } +} + + +// ----------------------------------------------------------------------------- +/* sets bits in a bit array (int) to toggle the reporting of the analogIns + */ +//void FirmataClass::setAnalogPinReporting(byte pin, byte state) { +//} +void reportAnalogCallback(byte analogPin, int value) +{ + if (analogPin < TOTAL_ANALOG_PINS) { + if(value == 0) { + analogInputsToReport = analogInputsToReport &~ (1 << analogPin); + } else { + analogInputsToReport = analogInputsToReport | (1 << analogPin); + } + } + // TODO: save status to EEPROM here, if changed +} + +void reportDigitalCallback(byte port, int value) +{ + if (port < TOTAL_PORTS) { + reportPINs[port] = (byte)value; + } + // do not disable analog reporting on these 8 pins, to allow some + // pins used for digital, others analog. Instead, allow both types + // of reporting to be enabled, but check if the pin is configured + // as analog when sampling the analog inputs. Likewise, while + // scanning digital pins, portConfigInputs will mask off values from any + // pins configured as analog +} + +/*============================================================================== + * SYSEX-BASED commands + *============================================================================*/ + +void sysexCallback(byte command, byte argc, byte *argv) +{ + switch(command) { + case SERVO_CONFIG: + if(argc > 4) { + // these vars are here for clarity, they'll optimized away by the compiler + byte pin = argv[0]; + int minPulse = argv[1] + (argv[2] << 7); + int maxPulse = argv[3] + (argv[4] << 7); + + if (IS_PIN_SERVO(pin)) { + // servos are pins from 2 to 13, so offset for array + if (servos[PIN_TO_SERVO(pin)].attached()) + servos[PIN_TO_SERVO(pin)].detach(); + servos[PIN_TO_SERVO(pin)].attach(PIN_TO_DIGITAL(pin), minPulse, maxPulse); + setPinModeCallback(pin, SERVO); + } + } + break; + case SAMPLING_INTERVAL: + if (argc > 1) + samplingInterval = argv[0] + (argv[1] << 7); + else + Firmata.sendString("Not enough data"); + break; + case EXTENDED_ANALOG: + if (argc > 1) { + int val = argv[1]; + if (argc > 2) val |= (argv[2] << 7); + if (argc > 3) val |= (argv[3] << 14); + analogWriteCallback(argv[0], val); + } + break; + case CAPABILITY_QUERY: + Serial.write(START_SYSEX); + Serial.write(CAPABILITY_RESPONSE); + for (byte pin=0; pin < TOTAL_PINS; pin++) { + if (IS_PIN_DIGITAL(pin)) { + Serial.write((byte)INPUT); + Serial.write(1); + Serial.write((byte)OUTPUT); + Serial.write(1); + } + if (IS_PIN_ANALOG(pin)) { + Serial.write(ANALOG); + Serial.write(10); + } + if (IS_PIN_PWM(pin)) { + Serial.write(PWM); + Serial.write(8); + } + if (IS_PIN_SERVO(pin)) { + Serial.write(SERVO); + Serial.write(14); + } + Serial.write(127); + } + Serial.write(END_SYSEX); + break; + case PIN_STATE_QUERY: + if (argc > 0) { + byte pin=argv[0]; + Serial.write(START_SYSEX); + Serial.write(PIN_STATE_RESPONSE); + Serial.write(pin); + if (pin < TOTAL_PINS) { + Serial.write((byte)pinConfig[pin]); + Serial.write((byte)pinState[pin] & 0x7F); + if (pinState[pin] & 0xFF80) Serial.write((byte)(pinState[pin] >> 7) & 0x7F); + if (pinState[pin] & 0xC000) Serial.write((byte)(pinState[pin] >> 14) & 0x7F); + } + Serial.write(END_SYSEX); + } + break; + case ANALOG_MAPPING_QUERY: + Serial.write(START_SYSEX); + Serial.write(ANALOG_MAPPING_RESPONSE); + for (byte pin=0; pin < TOTAL_PINS; pin++) { + Serial.write(IS_PIN_ANALOG(pin) ? PIN_TO_ANALOG(pin) : 127); + } + Serial.write(END_SYSEX); + break; + } +} + + +/*============================================================================== + * SETUP() + *============================================================================*/ +void setup() +{ + byte i; + + Firmata.setFirmwareVersion(2, 2); + + Firmata.attach(ANALOG_MESSAGE, analogWriteCallback); + Firmata.attach(DIGITAL_MESSAGE, digitalWriteCallback); + Firmata.attach(REPORT_ANALOG, reportAnalogCallback); + Firmata.attach(REPORT_DIGITAL, reportDigitalCallback); + Firmata.attach(SET_PIN_MODE, setPinModeCallback); + Firmata.attach(START_SYSEX, sysexCallback); + + // TODO: load state from EEPROM here + + /* these are initialized to zero by the compiler startup code + for (i=0; i < TOTAL_PORTS; i++) { + reportPINs[i] = false; + portConfigInputs[i] = 0; + previousPINs[i] = 0; + } + */ + for (i=0; i < TOTAL_PINS; i++) { + if (IS_PIN_ANALOG(i)) { + // turns off pullup, configures everything + setPinModeCallback(i, ANALOG); + } else { + // sets the output to 0, configures portConfigInputs + setPinModeCallback(i, OUTPUT); + } + } + // by defult, do not report any analog inputs + analogInputsToReport = 0; + + Firmata.begin(57600); + + /* send digital inputs to set the initial state on the host computer, + * since once in the loop(), this firmware will only send on change */ + for (i=0; i < TOTAL_PORTS; i++) { + outputPort(i, readPort(i, portConfigInputs[i]), true); + } +} + +/*============================================================================== + * LOOP() + *============================================================================*/ +void loop() +{ + byte pin, analogPin; + + /* DIGITALREAD - as fast as possible, check for changes and output them to the + * FTDI buffer using Serial.print() */ + checkDigitalInputs(); + + /* SERIALREAD - processing incoming messagse as soon as possible, while still + * checking digital inputs. */ + while(Firmata.available()) + Firmata.processInput(); + + /* SEND FTDI WRITE BUFFER - make sure that the FTDI buffer doesn't go over + * 60 bytes. use a timer to sending an event character every 4 ms to + * trigger the buffer to dump. */ + + currentMillis = millis(); + if (currentMillis - previousMillis > samplingInterval) { + previousMillis += samplingInterval; + /* ANALOGREAD - do all analogReads() at the configured sampling interval */ + for(pin=0; pin