From 4bfbbb3484cbc8ffccb90609e59a04796f618470 Mon Sep 17 00:00:00 2001 From: Fede85 Date: Wed, 26 Jun 2013 19:13:04 +0200 Subject: Ethernet, SD and LiquidCrystal to the new library format --- .../BarometricPressureWebServer.ino | 222 --------------------- .../Ethernet/examples/ChatServer/ChatServer.ino | 79 -------- .../Ethernet/examples/CosmClient/CosmClient.ino | 161 --------------- .../examples/CosmClientString/CosmClientString.ino | 146 -------------- .../DhcpAddressPrinter/DhcpAddressPrinter.ino | 59 ------ .../examples/DhcpChatServer/DhcpChatServer.ino | 87 -------- .../examples/PachubeClient/PachubeClient.ino | 163 --------------- .../PachubeClientString/PachubeClientString.ino | 152 -------------- .../examples/TelnetClient/TelnetClient.ino | 93 --------- .../examples/TwitterClient/TwitterClient.ino | 136 ------------- .../UDPSendReceiveString/UDPSendReceiveString.ino | 118 ----------- .../examples/UdpNtpClient/UdpNtpClient.ino | 141 ------------- .../Ethernet/examples/WebClient/WebClient.ino | 88 -------- .../WebClientRepeating/WebClientRepeating.ino | 111 ----------- .../Ethernet/examples/WebServer/WebServer.ino | 100 ---------- 15 files changed, 1856 deletions(-) delete mode 100644 libraries/Ethernet/examples/BarometricPressureWebServer/BarometricPressureWebServer.ino delete mode 100644 libraries/Ethernet/examples/ChatServer/ChatServer.ino delete mode 100644 libraries/Ethernet/examples/CosmClient/CosmClient.ino delete mode 100644 libraries/Ethernet/examples/CosmClientString/CosmClientString.ino delete mode 100644 libraries/Ethernet/examples/DhcpAddressPrinter/DhcpAddressPrinter.ino delete mode 100644 libraries/Ethernet/examples/DhcpChatServer/DhcpChatServer.ino delete mode 100644 libraries/Ethernet/examples/PachubeClient/PachubeClient.ino delete mode 100644 libraries/Ethernet/examples/PachubeClientString/PachubeClientString.ino delete mode 100644 libraries/Ethernet/examples/TelnetClient/TelnetClient.ino delete mode 100644 libraries/Ethernet/examples/TwitterClient/TwitterClient.ino delete mode 100644 libraries/Ethernet/examples/UDPSendReceiveString/UDPSendReceiveString.ino delete mode 100644 libraries/Ethernet/examples/UdpNtpClient/UdpNtpClient.ino delete mode 100644 libraries/Ethernet/examples/WebClient/WebClient.ino delete mode 100644 libraries/Ethernet/examples/WebClientRepeating/WebClientRepeating.ino delete mode 100644 libraries/Ethernet/examples/WebServer/WebServer.ino (limited to 'libraries/Ethernet/examples') diff --git a/libraries/Ethernet/examples/BarometricPressureWebServer/BarometricPressureWebServer.ino b/libraries/Ethernet/examples/BarometricPressureWebServer/BarometricPressureWebServer.ino deleted file mode 100644 index bfbcb6d..0000000 --- a/libraries/Ethernet/examples/BarometricPressureWebServer/BarometricPressureWebServer.ino +++ /dev/null @@ -1,222 +0,0 @@ -/* - SCP1000 Barometric Pressure Sensor Display - - Serves the output of a Barometric Pressure Sensor as a web page. - Uses the SPI library. For details on the sensor, see: - http://www.sparkfun.com/commerce/product_info.php?products_id=8161 - http://www.vti.fi/en/support/obsolete_products/pressure_sensors/ - - This sketch adapted from Nathan Seidle's SCP1000 example for PIC: - http://www.sparkfun.com/datasheets/Sensors/SCP1000-Testing.zip - - Circuit: - SCP1000 sensor attached to pins 6,7, and 11 - 13: - DRDY: pin 6 - CSB: pin 7 - MOSI: pin 11 - MISO: pin 12 - SCK: pin 13 - - created 31 July 2010 - by Tom Igoe - */ - -#include -// the sensor communicates using SPI, so include the library: -#include - - -// assign a MAC address for the ethernet controller. -// fill in your address here: -byte mac[] = { - 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED}; -// assign an IP address for the controller: -IPAddress ip(192,168,1,20); -IPAddress gateway(192,168,1,1); -IPAddress subnet(255, 255, 255, 0); - - -// Initialize the Ethernet server library -// with the IP address and port you want to use -// (port 80 is default for HTTP): -EthernetServer server(80); - - -//Sensor's memory register addresses: -const int PRESSURE = 0x1F; //3 most significant bits of pressure -const int PRESSURE_LSB = 0x20; //16 least significant bits of pressure -const int TEMPERATURE = 0x21; //16 bit temperature reading - -// pins used for the connection with the sensor -// the others you need are controlled by the SPI library): -const int dataReadyPin = 6; -const int chipSelectPin = 7; - -float temperature = 0.0; -long pressure = 0; -long lastReadingTime = 0; - -void setup() { - // start the SPI library: - SPI.begin(); - - // start the Ethernet connection and the server: - Ethernet.begin(mac, ip); - server.begin(); - - // initalize the data ready and chip select pins: - pinMode(dataReadyPin, INPUT); - pinMode(chipSelectPin, OUTPUT); - - Serial.begin(9600); - - //Configure SCP1000 for low noise configuration: - writeRegister(0x02, 0x2D); - writeRegister(0x01, 0x03); - writeRegister(0x03, 0x02); - - // give the sensor and Ethernet shield time to set up: - delay(1000); - - //Set the sensor to high resolution mode tp start readings: - writeRegister(0x03, 0x0A); - -} - -void loop() { - // check for a reading no more than once a second. - if (millis() - lastReadingTime > 1000){ - // if there's a reading ready, read it: - // don't do anything until the data ready pin is high: - if (digitalRead(dataReadyPin) == HIGH) { - getData(); - // timestamp the last time you got a reading: - lastReadingTime = millis(); - } - } - - // listen for incoming Ethernet connections: - listenForEthernetClients(); -} - - -void getData() { - Serial.println("Getting reading"); - //Read the temperature data - int tempData = readRegister(0x21, 2); - - // convert the temperature to celsius and display it: - temperature = (float)tempData / 20.0; - - //Read the pressure data highest 3 bits: - byte pressureDataHigh = readRegister(0x1F, 1); - pressureDataHigh &= 0b00000111; //you only needs bits 2 to 0 - - //Read the pressure data lower 16 bits: - unsigned int pressureDataLow = readRegister(0x20, 2); - //combine the two parts into one 19-bit number: - pressure = ((pressureDataHigh << 16) | pressureDataLow)/4; - - Serial.print("Temperature: "); - Serial.print(temperature); - Serial.println(" degrees C"); - Serial.print("Pressure: " + String(pressure)); - Serial.println(" Pa"); -} - -void listenForEthernetClients() { - // listen for incoming clients - EthernetClient client = server.available(); - if (client) { - Serial.println("Got a client"); - // an http request ends with a blank line - boolean currentLineIsBlank = true; - while (client.connected()) { - if (client.available()) { - char c = client.read(); - // if you've gotten to the end of the line (received a newline - // character) and the line is blank, the http request has ended, - // so you can send a reply - if (c == '\n' && currentLineIsBlank) { - // send a standard http response header - client.println("HTTP/1.1 200 OK"); - client.println("Content-Type: text/html"); - client.println(); - // print the current readings, in HTML format: - client.print("Temperature: "); - client.print(temperature); - client.print(" degrees C"); - client.println("
"); - client.print("Pressure: " + String(pressure)); - client.print(" Pa"); - client.println("
"); - break; - } - if (c == '\n') { - // you're starting a new line - currentLineIsBlank = true; - } - else if (c != '\r') { - // you've gotten a character on the current line - currentLineIsBlank = false; - } - } - } - // give the web browser time to receive the data - delay(1); - // close the connection: - client.stop(); - } -} - - -//Send a write command to SCP1000 -void writeRegister(byte registerName, byte registerValue) { - // SCP1000 expects the register name in the upper 6 bits - // of the byte: - registerName <<= 2; - // command (read or write) goes in the lower two bits: - registerName |= 0b00000010; //Write command - - // take the chip select low to select the device: - digitalWrite(chipSelectPin, LOW); - - SPI.transfer(registerName); //Send register location - SPI.transfer(registerValue); //Send value to record into register - - // take the chip select high to de-select: - digitalWrite(chipSelectPin, HIGH); -} - - -//Read register from the SCP1000: -unsigned int readRegister(byte registerName, int numBytes) { - byte inByte = 0; // incoming from the SPI read - unsigned int result = 0; // result to return - - // SCP1000 expects the register name in the upper 6 bits - // of the byte: - registerName <<= 2; - // command (read or write) goes in the lower two bits: - registerName &= 0b11111100; //Read command - - // take the chip select low to select the device: - digitalWrite(chipSelectPin, LOW); - // send the device the register you want to read: - int command = SPI.transfer(registerName); - // send a value of 0 to read the first byte returned: - inByte = SPI.transfer(0x00); - - result = inByte; - // if there's more than one byte returned, - // shift the first byte then get the second byte: - if (numBytes > 1){ - result = inByte << 8; - inByte = SPI.transfer(0x00); - result = result |inByte; - } - // take the chip select high to de-select: - digitalWrite(chipSelectPin, HIGH); - // return the result: - return(result); -} diff --git a/libraries/Ethernet/examples/ChatServer/ChatServer.ino b/libraries/Ethernet/examples/ChatServer/ChatServer.ino deleted file mode 100644 index d50e5a6..0000000 --- a/libraries/Ethernet/examples/ChatServer/ChatServer.ino +++ /dev/null @@ -1,79 +0,0 @@ -/* - Chat Server - - A simple server that distributes any incoming messages to all - connected clients. To use telnet to your device's IP address and type. - You can see the client's input in the serial monitor as well. - Using an Arduino Wiznet Ethernet shield. - - Circuit: - * Ethernet shield attached to pins 10, 11, 12, 13 - * Analog inputs attached to pins A0 through A5 (optional) - - created 18 Dec 2009 - by David A. Mellis - modified 9 Apr 2012 - by Tom Igoe - - */ - -#include -#include - -// Enter a MAC address and IP address for your controller below. -// The IP address will be dependent on your local network. -// gateway and subnet are optional: -byte mac[] = { - 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED }; -IPAddress ip(192,168,1, 177); -IPAddress gateway(192,168,1, 1); -IPAddress subnet(255, 255, 0, 0); - - -// telnet defaults to port 23 -EthernetServer server(23); -boolean alreadyConnected = false; // whether or not the client was connected previously - -void setup() { - // initialize the ethernet device - Ethernet.begin(mac, ip, gateway, subnet); - // start listening for clients - server.begin(); - // Open serial communications and wait for port to open: - Serial.begin(9600); - while (!Serial) { - ; // wait for serial port to connect. Needed for Leonardo only - } - - - Serial.print("Chat server address:"); - Serial.println(Ethernet.localIP()); -} - -void loop() { - // wait for a new client: - EthernetClient client = server.available(); - - // when the client sends the first byte, say hello: - if (client) { - if (!alreadyConnected) { - // clead out the input buffer: - client.flush(); - Serial.println("We have a new client"); - client.println("Hello, client!"); - alreadyConnected = true; - } - - if (client.available() > 0) { - // read the bytes incoming from the client: - char thisChar = client.read(); - // echo the bytes back to the client: - server.write(thisChar); - // echo the bytes to the server as well: - Serial.write(thisChar); - } - } -} - - - diff --git a/libraries/Ethernet/examples/CosmClient/CosmClient.ino b/libraries/Ethernet/examples/CosmClient/CosmClient.ino deleted file mode 100644 index ec74278..0000000 --- a/libraries/Ethernet/examples/CosmClient/CosmClient.ino +++ /dev/null @@ -1,161 +0,0 @@ -/* - Cosm sensor client - - This sketch connects an analog sensor to Cosm (http://www.cosm.com) - using a Wiznet Ethernet shield. You can use the Arduino Ethernet shield, or - the Adafruit Ethernet shield, either one will work, as long as it's got - a Wiznet Ethernet module on board. - - This example has been updated to use version 2.0 of the cosm.com API. - To make it work, create a feed with a datastream, and give it the ID - sensor1. Or change the code below to match your feed. - - - Circuit: - * Analog sensor attached to analog in 0 - * Ethernet shield attached to pins 10, 11, 12, 13 - - created 15 March 2010 - updated 14 May 2012 - by Tom Igoe with input from Usman Haque and Joe Saavedra - -http://arduino.cc/en/Tutorial/CosmClient - This code is in the public domain. - - */ - -#include -#include - -#define APIKEY "YOUR API KEY GOES HERE" // replace your Cosm api key here -#define FEEDID 00000 // replace your feed ID -#define USERAGENT "My Project" // user agent is the project name - -// assign a MAC address for the ethernet controller. -// Newer Ethernet shields have a MAC address printed on a sticker on the shield -// fill in your address here: -byte mac[] = { - 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED}; - -// fill in an available IP address on your network here, -// for manual configuration: -IPAddress ip(10,0,1,20); - -// initialize the library instance: -EthernetClient client; - -// if you don't want to use DNS (and reduce your sketch size) -// use the numeric IP instead of the name for the server: -//IPAddress server(216,52,233,121); // numeric IP for api.cosm.com -char server[] = "api.cosm.com"; // name address for cosm API - -unsigned long lastConnectionTime = 0; // last time you connected to the server, in milliseconds -boolean lastConnected = false; // state of the connection last time through the main loop -const unsigned long postingInterval = 10L*1000L; // delay between updates to cosm.com - // the "L" is needed to use long type numbers - - -void setup() { - // start serial port: - Serial.begin(9600); - // start the Ethernet connection: - if (Ethernet.begin(mac) == 0) { - Serial.println("Failed to configure Ethernet using DHCP"); - // DHCP failed, so use a fixed IP address: - Ethernet.begin(mac, ip); - } -} - -void loop() { - // read the analog sensor: - int sensorReading = analogRead(A0); - - // if there's incoming data from the net connection. - // send it out the serial port. This is for debugging - // purposes only: - if (client.available()) { - char c = client.read(); - Serial.print(c); - } - - // if there's no net connection, but there was one last time - // through the loop, then stop the client: - if (!client.connected() && lastConnected) { - Serial.println(); - Serial.println("disconnecting."); - client.stop(); - } - - // if you're not connected, and ten seconds have passed since - // your last connection, then connect again and send data: - if(!client.connected() && (millis() - lastConnectionTime > postingInterval)) { - sendData(sensorReading); - } - // store the state of the connection for next time through - // the loop: - lastConnected = client.connected(); -} - -// this method makes a HTTP connection to the server: -void sendData(int thisData) { - // if there's a successful connection: - if (client.connect(server, 80)) { - Serial.println("connecting..."); - // send the HTTP PUT request: - client.print("PUT /v2/feeds/"); - client.print(FEEDID); - client.println(".csv HTTP/1.1"); - client.println("Host: api.cosm.com"); - client.print("X-ApiKey: "); - client.println(APIKEY); - client.print("User-Agent: "); - client.println(USERAGENT); - client.print("Content-Length: "); - - // calculate the length of the sensor reading in bytes: - // 8 bytes for "sensor1," + number of digits of the data: - int thisLength = 8 + getLength(thisData); - client.println(thisLength); - - // last pieces of the HTTP PUT request: - client.println("Content-Type: text/csv"); - client.println("Connection: close"); - client.println(); - - // here's the actual content of the PUT request: - client.print("sensor1,"); - client.println(thisData); - - } - else { - // if you couldn't make a connection: - Serial.println("connection failed"); - Serial.println(); - Serial.println("disconnecting."); - client.stop(); - } - // note the time that the connection was made or attempted: - lastConnectionTime = millis(); -} - - -// This method calculates the number of digits in the -// sensor reading. Since each digit of the ASCII decimal -// representation is a byte, the number of digits equals -// the number of bytes: - -int getLength(int someValue) { - // there's at least one byte: - int digits = 1; - // continually divide the value by ten, - // adding one to the digit count for each - // time you divide, until you're at 0: - int dividend = someValue /10; - while (dividend > 0) { - dividend = dividend /10; - digits++; - } - // return the number of digits: - return digits; -} - diff --git a/libraries/Ethernet/examples/CosmClientString/CosmClientString.ino b/libraries/Ethernet/examples/CosmClientString/CosmClientString.ino deleted file mode 100644 index e619924..0000000 --- a/libraries/Ethernet/examples/CosmClientString/CosmClientString.ino +++ /dev/null @@ -1,146 +0,0 @@ -/* - Cosm sensor client with Strings - - This sketch connects an analog sensor to Cosm (http://www.cosm.com) - using a Wiznet Ethernet shield. You can use the Arduino Ethernet shield, or - the Adafruit Ethernet shield, either one will work, as long as it's got - a Wiznet Ethernet module on board. - - This example has been updated to use version 2.0 of the Cosm.com API. - To make it work, create a feed with two datastreams, and give them the IDs - sensor1 and sensor2. Or change the code below to match your feed. - - This example uses the String library, which is part of the Arduino core from - version 0019. - - Circuit: - * Analog sensor attached to analog in 0 - * Ethernet shield attached to pins 10, 11, 12, 13 - - created 15 March 2010 - updated 14 May 2012 - by Tom Igoe with input from Usman Haque and Joe Saavedra - - http://arduino.cc/en/Tutorial/CosmClientString - This code is in the public domain. - - */ - -#include -#include - - -#define APIKEY "YOUR API KEY GOES HERE" // replace your Cosm api key here -#define FEEDID 00000 // replace your feed ID -#define USERAGENT "My Project" // user agent is the project name - -// assign a MAC address for the ethernet controller. -// fill in your address here: - byte mac[] = { - 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED}; - -// fill in an available IP address on your network here, -// for manual configuration: -IPAddress ip(10,0,1,20); - -// initialize the library instance: -EthernetClient client; - -// if you don't want to use DNS (and reduce your sketch size) -// use the numeric IP instead of the name for the server: -//IPAddress server(216,52,233,121); // numeric IP for api.cosm.com -char server[] = "api.cosm.com"; // name address for Cosm API - -unsigned long lastConnectionTime = 0; // last time you connected to the server, in milliseconds -boolean lastConnected = false; // state of the connection last time through the main loop -const unsigned long postingInterval = 10L*1000L; // delay between updates to Cosm.com - // the "L" is needed to use long type numbers -void setup() { - // start serial port: - Serial.begin(9600); - // give the ethernet module time to boot up: - delay(1000); - // start the Ethernet connection: - if (Ethernet.begin(mac) == 0) { - Serial.println("Failed to configure Ethernet using DHCP"); - // DHCP failed, so use a fixed IP address: - Ethernet.begin(mac, ip); - } -} - -void loop() { - // read the analog sensor: - int sensorReading = analogRead(A0); - // convert the data to a String to send it: - - String dataString = "sensor1,"; - dataString += sensorReading; - - // you can append multiple readings to this String if your - // Cosm feed is set up to handle multiple values: - int otherSensorReading = analogRead(A1); - dataString += "\nsensor2,"; - dataString += otherSensorReading; - - // if there's incoming data from the net connection. - // send it out the serial port. This is for debugging - // purposes only: - if (client.available()) { - char c = client.read(); - Serial.print(c); - } - - // if there's no net connection, but there was one last time - // through the loop, then stop the client: - if (!client.connected() && lastConnected) { - Serial.println(); - Serial.println("disconnecting."); - client.stop(); - } - - // if you're not connected, and ten seconds have passed since - // your last connection, then connect again and send data: - if(!client.connected() && (millis() - lastConnectionTime > postingInterval)) { - sendData(dataString); - } - // store the state of the connection for next time through - // the loop: - lastConnected = client.connected(); -} - -// this method makes a HTTP connection to the server: -void sendData(String thisData) { - // if there's a successful connection: - if (client.connect(server, 80)) { - Serial.println("connecting..."); - // send the HTTP PUT request: - client.print("PUT /v2/feeds/"); - client.print(FEEDID); - client.println(".csv HTTP/1.1"); - client.println("Host: api.cosm.com"); - client.print("X-ApiKey: "); - client.println(APIKEY); - client.print("User-Agent: "); - client.println(USERAGENT); - client.print("Content-Length: "); - client.println(thisData.length()); - - // last pieces of the HTTP PUT request: - client.println("Content-Type: text/csv"); - client.println("Connection: close"); - client.println(); - - // here's the actual content of the PUT request: - client.println(thisData); - } - else { - // if you couldn't make a connection: - Serial.println("connection failed"); - Serial.println(); - Serial.println("disconnecting."); - client.stop(); - } - // note the time that the connection was made or attempted: - lastConnectionTime = millis(); -} - diff --git a/libraries/Ethernet/examples/DhcpAddressPrinter/DhcpAddressPrinter.ino b/libraries/Ethernet/examples/DhcpAddressPrinter/DhcpAddressPrinter.ino deleted file mode 100644 index 5eaaf24..0000000 --- a/libraries/Ethernet/examples/DhcpAddressPrinter/DhcpAddressPrinter.ino +++ /dev/null @@ -1,59 +0,0 @@ -/* - DHCP-based IP printer - - This sketch uses the DHCP extensions to the Ethernet library - to get an IP address via DHCP and print the address obtained. - using an Arduino Wiznet Ethernet shield. - - Circuit: - * Ethernet shield attached to pins 10, 11, 12, 13 - - created 12 April 2011 - modified 9 Apr 2012 - by Tom Igoe - - */ - -#include -#include - -// Enter a MAC address for your controller below. -// Newer Ethernet shields have a MAC address printed on a sticker on the shield -byte mac[] = { - 0x00, 0xAA, 0xBB, 0xCC, 0xDE, 0x02 }; - -// Initialize the Ethernet client library -// with the IP address and port of the server -// that you want to connect to (port 80 is default for HTTP): -EthernetClient client; - -void setup() { - // Open serial communications and wait for port to open: - Serial.begin(9600); - // this check is only needed on the Leonardo: - while (!Serial) { - ; // wait for serial port to connect. Needed for Leonardo only - } - - // start the Ethernet connection: - if (Ethernet.begin(mac) == 0) { - Serial.println("Failed to configure Ethernet using DHCP"); - // no point in carrying on, so do nothing forevermore: - for(;;) - ; - } - // print your local IP address: - Serial.print("My IP address: "); - for (byte thisByte = 0; thisByte < 4; thisByte++) { - // print the value of each byte of the IP address: - Serial.print(Ethernet.localIP()[thisByte], DEC); - Serial.print("."); - } - Serial.println(); -} - -void loop() { - -} - - diff --git a/libraries/Ethernet/examples/DhcpChatServer/DhcpChatServer.ino b/libraries/Ethernet/examples/DhcpChatServer/DhcpChatServer.ino deleted file mode 100644 index 09cbd43..0000000 --- a/libraries/Ethernet/examples/DhcpChatServer/DhcpChatServer.ino +++ /dev/null @@ -1,87 +0,0 @@ -/* - DHCP Chat Server - - A simple server that distributes any incoming messages to all - connected clients. To use telnet to your device's IP address and type. - You can see the client's input in the serial monitor as well. - Using an Arduino Wiznet Ethernet shield. - - THis version attempts to get an IP address using DHCP - - Circuit: - * Ethernet shield attached to pins 10, 11, 12, 13 - - created 21 May 2011 - modified 9 Apr 2012 - by Tom Igoe - Based on ChatServer example by David A. Mellis - - */ - -#include -#include - -// Enter a MAC address and IP address for your controller below. -// The IP address will be dependent on your local network. -// gateway and subnet are optional: -byte mac[] = { - 0x00, 0xAA, 0xBB, 0xCC, 0xDE, 0x02 }; -IPAddress ip(192,168,1, 177); -IPAddress gateway(192,168,1, 1); -IPAddress subnet(255, 255, 0, 0); - -// telnet defaults to port 23 -EthernetServer server(23); -boolean gotAMessage = false; // whether or not you got a message from the client yet - -void setup() { - // Open serial communications and wait for port to open: - Serial.begin(9600); - // this check is only needed on the Leonardo: - while (!Serial) { - ; // wait for serial port to connect. Needed for Leonardo only - } - - - // start the Ethernet connection: - Serial.println("Trying to get an IP address using DHCP"); - if (Ethernet.begin(mac) == 0) { - Serial.println("Failed to configure Ethernet using DHCP"); - // initialize the ethernet device not using DHCP: - Ethernet.begin(mac, ip, gateway, subnet); - } - // print your local IP address: - Serial.print("My IP address: "); - ip = Ethernet.localIP(); - for (byte thisByte = 0; thisByte < 4; thisByte++) { - // print the value of each byte of the IP address: - Serial.print(ip[thisByte], DEC); - Serial.print("."); - } - Serial.println(); - // start listening for clients - server.begin(); - -} - -void loop() { - // wait for a new client: - EthernetClient client = server.available(); - - // when the client sends the first byte, say hello: - if (client) { - if (!gotAMessage) { - Serial.println("We have a new client"); - client.println("Hello, client!"); - gotAMessage = true; - } - - // read the bytes incoming from the client: - char thisChar = client.read(); - // echo the bytes back to the client: - server.write(thisChar); - // echo the bytes to the server as well: - Serial.print(thisChar); - } -} - diff --git a/libraries/Ethernet/examples/PachubeClient/PachubeClient.ino b/libraries/Ethernet/examples/PachubeClient/PachubeClient.ino deleted file mode 100644 index dfd2d40..0000000 --- a/libraries/Ethernet/examples/PachubeClient/PachubeClient.ino +++ /dev/null @@ -1,163 +0,0 @@ -/* - Pachube sensor client - - This sketch connects an analog sensor to Pachube (http://www.pachube.com) - using a Wiznet Ethernet shield. You can use the Arduino Ethernet shield, or - the Adafruit Ethernet shield, either one will work, as long as it's got - a Wiznet Ethernet module on board. - - This example has been updated to use version 2.0 of the Pachube.com API. - To make it work, create a feed with a datastream, and give it the ID - sensor1. Or change the code below to match your feed. - - - Circuit: - * Analog sensor attached to analog in 0 - * Ethernet shield attached to pins 10, 11, 12, 13 - - created 15 March 2010 - modified 9 Apr 2012 - by Tom Igoe with input from Usman Haque and Joe Saavedra - -http://arduino.cc/en/Tutorial/PachubeClient - This code is in the public domain. - - */ - -#include -#include - -#define APIKEY "YOUR API KEY GOES HERE" // replace your pachube api key here -#define FEEDID 00000 // replace your feed ID -#define USERAGENT "My Project" // user agent is the project name - -// assign a MAC address for the ethernet controller. -// Newer Ethernet shields have a MAC address printed on a sticker on the shield -// fill in your address here: -byte mac[] = { - 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED}; - -// fill in an available IP address on your network here, -// for manual configuration: -IPAddress ip(10,0,1,20); -// initialize the library instance: -EthernetClient client; - -// if you don't want to use DNS (and reduce your sketch size) -// use the numeric IP instead of the name for the server: -IPAddress server(216,52,233,122); // numeric IP for api.pachube.com -//char server[] = "api.pachube.com"; // name address for pachube API - -unsigned long lastConnectionTime = 0; // last time you connected to the server, in milliseconds -boolean lastConnected = false; // state of the connection last time through the main loop -const unsigned long postingInterval = 10*1000; //delay between updates to Pachube.com - -void setup() { - // Open serial communications and wait for port to open: - Serial.begin(9600); - while (!Serial) { - ; // wait for serial port to connect. Needed for Leonardo only - } - - - // start the Ethernet connection: - if (Ethernet.begin(mac) == 0) { - Serial.println("Failed to configure Ethernet using DHCP"); - // DHCP failed, so use a fixed IP address: - Ethernet.begin(mac, ip); - } -} - -void loop() { - // read the analog sensor: - int sensorReading = analogRead(A0); - - // if there's incoming data from the net connection. - // send it out the serial port. This is for debugging - // purposes only: - if (client.available()) { - char c = client.read(); - Serial.print(c); - } - - // if there's no net connection, but there was one last time - // through the loop, then stop the client: - if (!client.connected() && lastConnected) { - Serial.println(); - Serial.println("disconnecting."); - client.stop(); - } - - // if you're not connected, and ten seconds have passed since - // your last connection, then connect again and send data: - if(!client.connected() && (millis() - lastConnectionTime > postingInterval)) { - sendData(sensorReading); - } - // store the state of the connection for next time through - // the loop: - lastConnected = client.connected(); -} - -// this method makes a HTTP connection to the server: -void sendData(int thisData) { - // if there's a successful connection: - if (client.connect(server, 80)) { - Serial.println("connecting..."); - // send the HTTP PUT request: - client.print("PUT /v2/feeds/"); - client.print(FEEDID); - client.println(".csv HTTP/1.1"); - client.println("Host: api.pachube.com"); - client.print("X-PachubeApiKey: "); - client.println(APIKEY); - client.print("User-Agent: "); - client.println(USERAGENT); - client.print("Content-Length: "); - - // calculate the length of the sensor reading in bytes: - // 8 bytes for "sensor1," + number of digits of the data: - int thisLength = 8 + getLength(thisData); - client.println(thisLength); - - // last pieces of the HTTP PUT request: - client.println("Content-Type: text/csv"); - client.println("Connection: close"); - client.println(); - - // here's the actual content of the PUT request: - client.print("sensor1,"); - client.println(thisData); - - } - else { - // if you couldn't make a connection: - Serial.println("connection failed"); - Serial.println(); - Serial.println("disconnecting."); - client.stop(); - } - // note the time that the connection was made or attempted: - lastConnectionTime = millis(); -} - - -// This method calculates the number of digits in the -// sensor reading. Since each digit of the ASCII decimal -// representation is a byte, the number of digits equals -// the number of bytes: - -int getLength(int someValue) { - // there's at least one byte: - int digits = 1; - // continually divide the value by ten, - // adding one to the digit count for each - // time you divide, until you're at 0: - int dividend = someValue /10; - while (dividend > 0) { - dividend = dividend /10; - digits++; - } - // return the number of digits: - return digits; -} - diff --git a/libraries/Ethernet/examples/PachubeClientString/PachubeClientString.ino b/libraries/Ethernet/examples/PachubeClientString/PachubeClientString.ino deleted file mode 100644 index 2a96e9f..0000000 --- a/libraries/Ethernet/examples/PachubeClientString/PachubeClientString.ino +++ /dev/null @@ -1,152 +0,0 @@ -/* - Cosm sensor client with Strings - - This sketch connects an analog sensor to Cosm (http://www.cosm.com) - using a Wiznet Ethernet shield. You can use the Arduino Ethernet shield, or - the Adafruit Ethernet shield, either one will work, as long as it's got - a Wiznet Ethernet module on board. - - This example has been updated to use version 2.0 of the Cosm.com API. - To make it work, create a feed with two datastreams, and give them the IDs - sensor1 and sensor2. Or change the code below to match your feed. - - This example uses the String library, which is part of the Arduino core from - version 0019. - - Circuit: - * Analog sensor attached to analog in 0 - * Ethernet shield attached to pins 10, 11, 12, 13 - - created 15 March 2010 - modified 9 Apr 2012 - by Tom Igoe with input from Usman Haque and Joe Saavedra - - http://arduino.cc/en/Tutorial/CosmClientString - This code is in the public domain. - - */ - -#include -#include - - -/#define APIKEY "YOUR API KEY GOES HERE" // replace your Cosm api key here -#define FEEDID 00000 // replace your feed ID -#define USERAGENT "My Project" // user agent is the project name - - -// assign a MAC address for the ethernet controller. -// fill in your address here: - byte mac[] = { - 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED}; - -// fill in an available IP address on your network here, -// for manual configuration: -IPAddress ip(10,0,1,20); - -// initialize the library instance: -EthernetClient client; - -// if you don't want to use DNS (and reduce your sketch size) -// use the numeric IP instead of the name for the server: -IPAddress server(216,52,233,121); // numeric IP for api.cosm.com -//char server[] = "api.cosm.com"; // name address for Cosm API - -unsigned long lastConnectionTime = 0; // last time you connected to the server, in milliseconds -boolean lastConnected = false; // state of the connection last time through the main loop -const unsigned long postingInterval = 10*1000; //delay between updates to Cosm.com - -void setup() { - // Open serial communications and wait for port to open: - Serial.begin(9600); - while (!Serial) { - ; // wait for serial port to connect. Needed for Leonardo only - } - - - // give the ethernet module time to boot up: - delay(1000); - // start the Ethernet connection: - if (Ethernet.begin(mac) == 0) { - Serial.println("Failed to configure Ethernet using DHCP"); - // DHCP failed, so use a fixed IP address: - Ethernet.begin(mac, ip); - } -} - -void loop() { - // read the analog sensor: - int sensorReading = analogRead(A0); - // convert the data to a String to send it: - - String dataString = "sensor1,"; - dataString += sensorReading; - - // you can append multiple readings to this String if your - // Cosm feed is set up to handle multiple values: - int otherSensorReading = analogRead(A1); - dataString += "\nsensor2,"; - dataString += otherSensorReading; - - // if there's incoming data from the net connection. - // send it out the serial port. This is for debugging - // purposes only: - if (client.available()) { - char c = client.read(); - Serial.print(c); - } - - // if there's no net connection, but there was one last time - // through the loop, then stop the client: - if (!client.connected() && lastConnected) { - Serial.println(); - Serial.println("disconnecting."); - client.stop(); - } - - // if you're not connected, and ten seconds have passed since - // your last connection, then connect again and send data: - if(!client.connected() && (millis() - lastConnectionTime > postingInterval)) { - sendData(dataString); - } - // store the state of the connection for next time through - // the loop: - lastConnected = client.connected(); -} - -// this method makes a HTTP connection to the server: -void sendData(String thisData) { - // if there's a successful connection: - if (client.connect(server, 80)) { - Serial.println("connecting..."); - // send the HTTP PUT request: - client.print("PUT /v2/feeds/"); - client.print(FEEDID); - client.println(".csv HTTP/1.1"); - client.println("Host: api.cosm.com"); - client.print("X-CosmApiKey: "); - client.println(APIKEY); - client.print("User-Agent: "); - client.println(USERAGENT); - client.print("Content-Length: "); - client.println(thisData.length()); - - // last pieces of the HTTP PUT request: - client.println("Content-Type: text/csv"); - client.println("Connection: close"); - client.println(); - - // here's the actual content of the PUT request: - client.println(thisData); - } - else { - // if you couldn't make a connection: - Serial.println("connection failed"); - Serial.println(); - Serial.println("disconnecting."); - client.stop(); - } - // note the time that the connection was made or attempted: - lastConnectionTime = millis(); -} - diff --git a/libraries/Ethernet/examples/TelnetClient/TelnetClient.ino b/libraries/Ethernet/examples/TelnetClient/TelnetClient.ino deleted file mode 100644 index 3457125..0000000 --- a/libraries/Ethernet/examples/TelnetClient/TelnetClient.ino +++ /dev/null @@ -1,93 +0,0 @@ -/* - Telnet client - - This sketch connects to a a telnet server (http://www.google.com) - using an Arduino Wiznet Ethernet shield. You'll need a telnet server - to test this with. - Processing's ChatServer example (part of the network library) works well, - running on port 10002. It can be found as part of the examples - in the Processing application, available at - http://processing.org/ - - Circuit: - * Ethernet shield attached to pins 10, 11, 12, 13 - - created 14 Sep 2010 - modified 9 Apr 2012 - by Tom Igoe - - */ - -#include -#include - -// Enter a MAC address and IP address for your controller below. -// The IP address will be dependent on your local network: -byte mac[] = { - 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED }; -IPAddress ip(192,168,1,177); - -// Enter the IP address of the server you're connecting to: -IPAddress server(1,1,1,1); - -// Initialize the Ethernet client library -// with the IP address and port of the server -// that you want to connect to (port 23 is default for telnet; -// if you're using Processing's ChatServer, use port 10002): -EthernetClient client; - -void setup() { - // start the Ethernet connection: - Ethernet.begin(mac, ip); - // Open serial communications and wait for port to open: - Serial.begin(9600); - while (!Serial) { - ; // wait for serial port to connect. Needed for Leonardo only - } - - - // give the Ethernet shield a second to initialize: - delay(1000); - Serial.println("connecting..."); - - // if you get a connection, report back via serial: - if (client.connect(server, 10002)) { - Serial.println("connected"); - } - else { - // if you didn't get a connection to the server: - Serial.println("connection failed"); - } -} - -void loop() -{ - // if there are incoming bytes available - // from the server, read them and print them: - if (client.available()) { - char c = client.read(); - Serial.print(c); - } - - // as long as there are bytes in the serial queue, - // read them and send them out the socket if it's open: - while (Serial.available() > 0) { - char inChar = Serial.read(); - if (client.connected()) { - client.print(inChar); - } - } - - // if the server's disconnected, stop the client: - if (!client.connected()) { - Serial.println(); - Serial.println("disconnecting."); - client.stop(); - // do nothing: - while(true); - } -} - - - - diff --git a/libraries/Ethernet/examples/TwitterClient/TwitterClient.ino b/libraries/Ethernet/examples/TwitterClient/TwitterClient.ino deleted file mode 100644 index 9fee1fe..0000000 --- a/libraries/Ethernet/examples/TwitterClient/TwitterClient.ino +++ /dev/null @@ -1,136 +0,0 @@ -/* - Twitter Client with Strings - - This sketch connects to Twitter using an Ethernet shield. It parses the XML - returned, and looks for this is a tweet - - You can use the Arduino Ethernet shield, or the Adafruit Ethernet shield, - either one will work, as long as it's got a Wiznet Ethernet module on board. - - This example uses the DHCP routines in the Ethernet library which is part of the - Arduino core from version 1.0 beta 1 - - This example uses the String library, which is part of the Arduino core from - version 0019. - - Circuit: - * Ethernet shield attached to pins 10, 11, 12, 13 - - created 21 May 2011 - modified 9 Apr 2012 - by Tom Igoe - - This code is in the public domain. - - */ -#include -#include - - -// Enter a MAC address and IP address for your controller below. -// The IP address will be dependent on your local network: -byte mac[] = { - 0x00, 0xAA, 0xBB, 0xCC, 0xDE, 0x01 }; -IPAddress ip(192,168,1,20); - -// initialize the library instance: -EthernetClient client; - -const unsigned long requestInterval = 60000; // delay between requests - -char serverName[] = "api.twitter.com"; // twitter URL - -boolean requested; // whether you've made a request since connecting -unsigned long lastAttemptTime = 0; // last time you connected to the server, in milliseconds - -String currentLine = ""; // string to hold the text from server -String tweet = ""; // string to hold the tweet -boolean readingTweet = false; // if you're currently reading the tweet - -void setup() { - // reserve space for the strings: - currentLine.reserve(256); - tweet.reserve(150); - - // Open serial communications and wait for port to open: - Serial.begin(9600); - while (!Serial) { - ; // wait for serial port to connect. Needed for Leonardo only - } - - - // attempt a DHCP connection: - Serial.println("Attempting to get an IP address using DHCP:"); - if (!Ethernet.begin(mac)) { - // if DHCP fails, start with a hard-coded address: - Serial.println("failed to get an IP address using DHCP, trying manually"); - Ethernet.begin(mac, ip); - } - Serial.print("My address:"); - Serial.println(Ethernet.localIP()); - // connect to Twitter: - connectToServer(); -} - - - -void loop() -{ - if (client.connected()) { - if (client.available()) { - // read incoming bytes: - char inChar = client.read(); - - // add incoming byte to end of line: - currentLine += inChar; - - // if you get a newline, clear the line: - if (inChar == '\n') { - currentLine = ""; - } - // if the current line ends with , it will - // be followed by the tweet: - if ( currentLine.endsWith("")) { - // tweet is beginning. Clear the tweet string: - readingTweet = true; - tweet = ""; - } - // if you're currently reading the bytes of a tweet, - // add them to the tweet String: - if (readingTweet) { - if (inChar != '<') { - tweet += inChar; - } - else { - // if you got a "<" character, - // you've reached the end of the tweet: - readingTweet = false; - Serial.println(tweet); - // close the connection to the server: - client.stop(); - } - } - } - } - else if (millis() - lastAttemptTime > requestInterval) { - // if you're not connected, and two minutes have passed since - // your last connection, then attempt to connect again: - connectToServer(); - } -} - -void connectToServer() { - // attempt to connect, and wait a millisecond: - Serial.println("connecting to server..."); - if (client.connect(serverName, 80)) { - Serial.println("making HTTP request..."); - // make HTTP GET request to twitter: - client.println("GET /1/statuses/user_timeline.xml?screen_name=arduino&count=1 HTTP/1.1"); - client.println("HOST: api.twitter.com"); - client.println("Connection: close"); - client.println(); - } - // note the time of this connect attempt: - lastAttemptTime = millis(); -} - diff --git a/libraries/Ethernet/examples/UDPSendReceiveString/UDPSendReceiveString.ino b/libraries/Ethernet/examples/UDPSendReceiveString/UDPSendReceiveString.ino deleted file mode 100644 index 4d4045c..0000000 --- a/libraries/Ethernet/examples/UDPSendReceiveString/UDPSendReceiveString.ino +++ /dev/null @@ -1,118 +0,0 @@ -/* - UDPSendReceive.pde: - This sketch receives UDP message strings, prints them to the serial port - and sends an "acknowledge" string back to the sender - - A Processing sketch is included at the end of file that can be used to send - and received messages for testing with a computer. - - created 21 Aug 2010 - by Michael Margolis - - This code is in the public domain. - */ - - -#include // needed for Arduino versions later than 0018 -#include -#include // UDP library from: bjoern@cs.stanford.edu 12/30/2008 - - -// Enter a MAC address and IP address for your controller below. -// The IP address will be dependent on your local network: -byte mac[] = { - 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED }; -IPAddress ip(192, 168, 1, 177); - -unsigned int localPort = 8888; // local port to listen on - -// buffers for receiving and sending data -char packetBuffer[UDP_TX_PACKET_MAX_SIZE]; //buffer to hold incoming packet, -char ReplyBuffer[] = "acknowledged"; // a string to send back - -// An EthernetUDP instance to let us send and receive packets over UDP -EthernetUDP Udp; - -void setup() { - // start the Ethernet and UDP: - Ethernet.begin(mac,ip); - Udp.begin(localPort); - - Serial.begin(9600); -} - -void loop() { - // if there's data available, read a packet - int packetSize = Udp.parsePacket(); - if(packetSize) - { - Serial.print("Received packet of size "); - Serial.println(packetSize); - Serial.print("From "); - IPAddress remote = Udp.remoteIP(); - for (int i =0; i < 4; i++) - { - Serial.print(remote[i], DEC); - if (i < 3) - { - Serial.print("."); - } - } - Serial.print(", port "); - Serial.println(Udp.remotePort()); - - // read the packet into packetBufffer - Udp.read(packetBuffer,UDP_TX_PACKET_MAX_SIZE); - Serial.println("Contents:"); - Serial.println(packetBuffer); - - // send a reply, to the IP address and port that sent us the packet we received - Udp.beginPacket(Udp.remoteIP(), Udp.remotePort()); - Udp.write(ReplyBuffer); - Udp.endPacket(); - } - delay(10); -} - - -/* - Processing sketch to run with this example - ===================================================== - - // Processing UDP example to send and receive string data from Arduino - // press any key to send the "Hello Arduino" message - - - import hypermedia.net.*; - - UDP udp; // define the UDP object - - - void setup() { - udp = new UDP( this, 6000 ); // create a new datagram connection on port 6000 - //udp.log( true ); // <-- printout the connection activity - udp.listen( true ); // and wait for incoming message - } - - void draw() - { - } - - void keyPressed() { - String ip = "192.168.1.177"; // the remote IP address - int port = 8888; // the destination port - - udp.send("Hello World", ip, port ); // the message to send - - } - - void receive( byte[] data ) { // <-- default handler - //void receive( byte[] data, String ip, int port ) { // <-- extended handler - - for(int i=0; i < data.length; i++) - print(char(data[i])); - println(); - } - */ - - diff --git a/libraries/Ethernet/examples/UdpNtpClient/UdpNtpClient.ino b/libraries/Ethernet/examples/UdpNtpClient/UdpNtpClient.ino deleted file mode 100644 index 93ffe39..0000000 --- a/libraries/Ethernet/examples/UdpNtpClient/UdpNtpClient.ino +++ /dev/null @@ -1,141 +0,0 @@ -/* - - Udp NTP Client - - Get the time from a Network Time Protocol (NTP) time server - Demonstrates use of UDP sendPacket and ReceivePacket - For more on NTP time servers and the messages needed to communicate with them, - see http://en.wikipedia.org/wiki/Network_Time_Protocol - - created 4 Sep 2010 - by Michael Margolis - modified 9 Apr 2012 - by Tom Igoe - - This code is in the public domain. - - */ - -#include -#include -#include - -// Enter a MAC address for your controller below. -// Newer Ethernet shields have a MAC address printed on a sticker on the shield -byte mac[] = { - 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED }; - -unsigned int localPort = 8888; // local port to listen for UDP packets - -IPAddress timeServer(192, 43, 244, 18); // time.nist.gov NTP server - -const int NTP_PACKET_SIZE= 48; // NTP time stamp is in the first 48 bytes of the message - -byte packetBuffer[ NTP_PACKET_SIZE]; //buffer to hold incoming and outgoing packets - -// A UDP instance to let us send and receive packets over UDP -EthernetUDP Udp; - -void setup() -{ - // Open serial communications and wait for port to open: - Serial.begin(9600); - while (!Serial) { - ; // wait for serial port to connect. Needed for Leonardo only - } - - - // start Ethernet and UDP - if (Ethernet.begin(mac) == 0) { - Serial.println("Failed to configure Ethernet using DHCP"); - // no point in carrying on, so do nothing forevermore: - for(;;) - ; - } - Udp.begin(localPort); -} - -void loop() -{ - sendNTPpacket(timeServer); // send an NTP packet to a time server - - // wait to see if a reply is available - delay(1000); - if ( Udp.parsePacket() ) { - // We've received a packet, read the data from it - Udp.read(packetBuffer,NTP_PACKET_SIZE); // read the packet into the buffer - - //the timestamp starts at byte 40 of the received packet and is four bytes, - // or two words, long. First, esxtract the two words: - - unsigned long highWord = word(packetBuffer[40], packetBuffer[41]); - unsigned long lowWord = word(packetBuffer[42], packetBuffer[43]); - // combine the four bytes (two words) into a long integer - // this is NTP time (seconds since Jan 1 1900): - unsigned long secsSince1900 = highWord << 16 | lowWord; - Serial.print("Seconds since Jan 1 1900 = " ); - Serial.println(secsSince1900); - - // now convert NTP time into everyday time: - Serial.print("Unix time = "); - // Unix time starts on Jan 1 1970. In seconds, that's 2208988800: - const unsigned long seventyYears = 2208988800UL; - // subtract seventy years: - unsigned long epoch = secsSince1900 - seventyYears; - // print Unix time: - Serial.println(epoch); - - - // print the hour, minute and second: - Serial.print("The UTC time is "); // UTC is the time at Greenwich Meridian (GMT) - Serial.print((epoch % 86400L) / 3600); // print the hour (86400 equals secs per day) - Serial.print(':'); - if ( ((epoch % 3600) / 60) < 10 ) { - // In the first 10 minutes of each hour, we'll want a leading '0' - Serial.print('0'); - } - Serial.print((epoch % 3600) / 60); // print the minute (3600 equals secs per minute) - Serial.print(':'); - if ( (epoch % 60) < 10 ) { - // In the first 10 seconds of each minute, we'll want a leading '0' - Serial.print('0'); - } - Serial.println(epoch %60); // print the second - } - // wait ten seconds before asking for the time again - delay(10000); -} - -// send an NTP request to the time server at the given address -unsigned long sendNTPpacket(IPAddress& address) -{ - // set all bytes in the buffer to 0 - memset(packetBuffer, 0, NTP_PACKET_SIZE); - // Initialize values needed to form NTP request - // (see URL above for details on the packets) - packetBuffer[0] = 0b11100011; // LI, Version, Mode - packetBuffer[1] = 0; // Stratum, or type of clock - packetBuffer[2] = 6; // Polling Interval - packetBuffer[3] = 0xEC; // Peer Clock Precision - // 8 bytes of zero for Root Delay & Root Dispersion - packetBuffer[12] = 49; - packetBuffer[13] = 0x4E; - packetBuffer[14] = 49; - packetBuffer[15] = 52; - - // all NTP fields have been given values, now - // you can send a packet requesting a timestamp: - Udp.beginPacket(address, 123); //NTP requests are to port 123 - Udp.write(packetBuffer,NTP_PACKET_SIZE); - Udp.endPacket(); -} - - - - - - - - - - diff --git a/libraries/Ethernet/examples/WebClient/WebClient.ino b/libraries/Ethernet/examples/WebClient/WebClient.ino deleted file mode 100644 index 40523a4..0000000 --- a/libraries/Ethernet/examples/WebClient/WebClient.ino +++ /dev/null @@ -1,88 +0,0 @@ -/* - Web client - - This sketch connects to a website (http://www.google.com) - using an Arduino Wiznet Ethernet shield. - - Circuit: - * Ethernet shield attached to pins 10, 11, 12, 13 - - created 18 Dec 2009 - by David A. Mellis - modified 9 Apr 2012 - by Tom Igoe, based on work by Adrian McEwen - - */ - -#include -#include - -// Enter a MAC address for your controller below. -// Newer Ethernet shields have a MAC address printed on a sticker on the shield -byte mac[] = { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED }; -// if you don't want to use DNS (and reduce your sketch size) -// use the numeric IP instead of the name for the server: -//IPAddress server(74,125,232,128); // numeric IP for Google (no DNS) -char server[] = "www.google.com"; // name address for Google (using DNS) - -// Set the static IP address to use if the DHCP fails to assign -IPAddress ip(192,168,0,177); - -// Initialize the Ethernet client library -// with the IP address and port of the server -// that you want to connect to (port 80 is default for HTTP): -EthernetClient client; - -void setup() { - // Open serial communications and wait for port to open: - Serial.begin(9600); - while (!Serial) { - ; // wait for serial port to connect. Needed for Leonardo only - } - - // start the Ethernet connection: - if (Ethernet.begin(mac) == 0) { - Serial.println("Failed to configure Ethernet using DHCP"); - // no point in carrying on, so do nothing forevermore: - // try to congifure using IP address instead of DHCP: - Ethernet.begin(mac, ip); - } - // give the Ethernet shield a second to initialize: - delay(1000); - Serial.println("connecting..."); - - // if you get a connection, report back via serial: - if (client.connect(server, 80)) { - Serial.println("connected"); - // Make a HTTP request: - client.println("GET /search?q=arduino HTTP/1.1"); - client.println("Host: www.google.com"); - client.println("Connection: close"); - client.println(); - } - else { - // kf you didn't get a connection to the server: - Serial.println("connection failed"); - } -} - -void loop() -{ - // if there are incoming bytes available - // from the server, read them and print them: - if (client.available()) { - char c = client.read(); - Serial.print(c); - } - - // if the server's disconnected, stop the client: - if (!client.connected()) { - Serial.println(); - Serial.println("disconnecting."); - client.stop(); - - // do nothing forevermore: - while(true); - } -} - diff --git a/libraries/Ethernet/examples/WebClientRepeating/WebClientRepeating.ino b/libraries/Ethernet/examples/WebClientRepeating/WebClientRepeating.ino deleted file mode 100644 index 650f74e..0000000 --- a/libraries/Ethernet/examples/WebClientRepeating/WebClientRepeating.ino +++ /dev/null @@ -1,111 +0,0 @@ -/* - Repeating Web client - - This sketch connects to a a web server and makes a request - using a Wiznet Ethernet shield. You can use the Arduino Ethernet shield, or - the Adafruit Ethernet shield, either one will work, as long as it's got - a Wiznet Ethernet module on board. - - This example uses DNS, by assigning the Ethernet client with a MAC address, - IP address, and DNS address. - - Circuit: - * Ethernet shield attached to pins 10, 11, 12, 13 - - created 19 Apr 2012 - by Tom Igoe - - http://arduino.cc/en/Tutorial/WebClientRepeating - This code is in the public domain. - - */ - -#include -#include - -// assign a MAC address for the ethernet controller. -// fill in your address here: -byte mac[] = { - 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED}; -// fill in an available IP address on your network here, -// for manual configuration: -IPAddress ip(10,0,0,20); - -// fill in your Domain Name Server address here: -IPAddress myDns(1,1,1,1); - -// initialize the library instance: -EthernetClient client; - -char server[] = "www.arduino.cc"; - -unsigned long lastConnectionTime = 0; // last time you connected to the server, in milliseconds -boolean lastConnected = false; // state of the connection last time through the main loop -const unsigned long postingInterval = 60L*1000L; // delay between updates, in milliseconds - // the "L" is needed to use long type numbers - -void setup() { - // start serial port: - Serial.begin(9600); - // give the ethernet module time to boot up: - delay(1000); - // start the Ethernet connection using a fixed IP address and DNS server: - Ethernet.begin(mac, ip, myDns); - // print the Ethernet board/shield's IP address: - Serial.print("My IP address: "); - Serial.println(Ethernet.localIP()); -} - -void loop() { - // if there's incoming data from the net connection. - // send it out the serial port. This is for debugging - // purposes only: - if (client.available()) { - char c = client.read(); - Serial.print(c); - } - - // if there's no net connection, but there was one last time - // through the loop, then stop the client: - if (!client.connected() && lastConnected) { - Serial.println(); - Serial.println("disconnecting."); - client.stop(); - } - - // if you're not connected, and ten seconds have passed since - // your last connection, then connect again and send data: - if(!client.connected() && (millis() - lastConnectionTime > postingInterval)) { - httpRequest(); - } - // store the state of the connection for next time through - // the loop: - lastConnected = client.connected(); -} - -// this method makes a HTTP connection to the server: -void httpRequest() { - // if there's a successful connection: - if (client.connect(server, 80)) { - Serial.println("connecting..."); - // send the HTTP PUT request: - client.println("GET /latest.txt HTTP/1.1"); - client.println("Host: www.arduino.cc"); - client.println("User-Agent: arduino-ethernet"); - client.println("Connection: close"); - client.println(); - - // note the time that the connection was made: - lastConnectionTime = millis(); - } - else { - // if you couldn't make a connection: - Serial.println("connection failed"); - Serial.println("disconnecting."); - client.stop(); - } -} - - - - diff --git a/libraries/Ethernet/examples/WebServer/WebServer.ino b/libraries/Ethernet/examples/WebServer/WebServer.ino deleted file mode 100644 index 5e5d67a..0000000 --- a/libraries/Ethernet/examples/WebServer/WebServer.ino +++ /dev/null @@ -1,100 +0,0 @@ -/* - Web Server - - A simple web server that shows the value of the analog input pins. - using an Arduino Wiznet Ethernet shield. - - Circuit: - * Ethernet shield attached to pins 10, 11, 12, 13 - * Analog inputs attached to pins A0 through A5 (optional) - - created 18 Dec 2009 - by David A. Mellis - modified 9 Apr 2012 - by Tom Igoe - - */ - -#include -#include - -// Enter a MAC address and IP address for your controller below. -// The IP address will be dependent on your local network: -byte mac[] = { - 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED }; -IPAddress ip(192,168,1,177); - -// Initialize the Ethernet server library -// with the IP address and port you want to use -// (port 80 is default for HTTP): -EthernetServer server(80); - -void setup() { - // Open serial communications and wait for port to open: - Serial.begin(9600); - while (!Serial) { - ; // wait for serial port to connect. Needed for Leonardo only - } - - - // start the Ethernet connection and the server: - Ethernet.begin(mac, ip); - server.begin(); - Serial.print("server is at "); - Serial.println(Ethernet.localIP()); -} - - -void loop() { - // listen for incoming clients - EthernetClient client = server.available(); - if (client) { - Serial.println("new client"); - // an http request ends with a blank line - boolean currentLineIsBlank = true; - while (client.connected()) { - if (client.available()) { - char c = client.read(); - Serial.write(c); - // if you've gotten to the end of the line (received a newline - // character) and the line is blank, the http request has ended, - // so you can send a reply - if (c == '\n' && currentLineIsBlank) { - // send a standard http response header - client.println("HTTP/1.1 200 OK"); - client.println("Content-Type: text/html"); - client.println("Connection: close"); // the connection will be closed after completion of the response - client.println("Refresh: 5"); // refresh the page automatically every 5 sec - client.println(); - client.println(""); - client.println(""); - // output the value of each analog input pin - for (int analogChannel = 0; analogChannel < 6; analogChannel++) { - int sensorReading = analogRead(analogChannel); - client.print("analog input "); - client.print(analogChannel); - client.print(" is "); - client.print(sensorReading); - client.println("
"); - } - client.println(""); - break; - } - if (c == '\n') { - // you're starting a new line - currentLineIsBlank = true; - } - else if (c != '\r') { - // you've gotten a character on the current line - currentLineIsBlank = false; - } - } - } - // give the web browser time to receive the data - delay(1); - // close the connection: - client.stop(); - Serial.println("client disonnected"); - } -} - -- cgit v1.2.3-18-g5258