From a3e2e68e2b7edb9f5434734bed4001df1e65451c Mon Sep 17 00:00:00 2001 From: Fede85 Date: Fri, 6 Sep 2013 15:38:07 +0200 Subject: Bridge library to the 1.5 format --- .../YunSerialTerminal/YunSerialTerminal.ino | 78 ---------------------- 1 file changed, 78 deletions(-) delete mode 100644 libraries/Bridge/examples/YunSerialTerminal/YunSerialTerminal.ino (limited to 'libraries/Bridge/examples/YunSerialTerminal/YunSerialTerminal.ino') diff --git a/libraries/Bridge/examples/YunSerialTerminal/YunSerialTerminal.ino b/libraries/Bridge/examples/YunSerialTerminal/YunSerialTerminal.ino deleted file mode 100644 index faffd93..0000000 --- a/libraries/Bridge/examples/YunSerialTerminal/YunSerialTerminal.ino +++ /dev/null @@ -1,78 +0,0 @@ -/* - Arduino Yun USB-to-Serial - - Allows you to use the Yun's 32U4 processor as a - serial terminal for the linino processor. - - Upload this to an Arduino Yun via serial (not WiFi) - then open the serial monitor at 115200 to see the boot process - of the linino processor. You can also use the serial monitor - as a basic command line interface for the linino processor using - this sketch. - - From the serial monitor the following commands can be issued: - - '~' followed by '0' -> Set the UART speed to 57600 baud - '~' followed by '1' -> Set the UART speed to 115200 baud - '~' followed by '2' -> Set the UART speed to 250000 baud - '~' followed by '3' -> Set the UART speed to 500000 baud - '~' followeb by '~' -> Sends the bridge's shutdown command to - obtain the console. - - The circuit: - * Arduino Yun - - created March 2013 - by Massimo Banzi - modified by Cristian Maglie - - This example code is in the public domain. - */ - -long lininoBaud = 250000; - -void setup() { - Serial.begin(115200); // open serial connection via USB-Serial - Serial1.begin(lininoBaud); // open serial connection to Linino -} - -boolean commandMode = false; - -void loop() { - // copy from virtual serial line to uart and vice versa - if (Serial.available()) { // got anything from USB-Serial? - char c = (char)Serial.read(); // read from USB-serial - if (commandMode == false) { // if we aren't in command mode... - if (c == '~') { // Tilde '~' key pressed? - commandMode = true; // enter in command mode - } else { - Serial1.write(c); // otherwise write char to Linino - } - } else { // if we are in command mode... - if (c == '0') { // '0' key pressed? - Serial1.begin(57600); // set speed to 57600 - Serial.println("Speed set to 57600"); - } else if (c == '1') { // '1' key pressed? - Serial1.begin(115200); // set speed to 115200 - Serial.println("Speed set to 115200"); - } else if (c == '2') { // '2' key pressed? - Serial1.begin(250000); // set speed to 250000 - Serial.println("Speed set to 250000"); - } else if (c == '3') { // '3' key pressed? - Serial1.begin(500000); // set speed to 500000 - Serial.println("Speed set to 500000"); - } else if (c == '~') { - Serial1.write((uint8_t *)"\xff\0\0\x05XXXXX\x0d\xaf", 11); - Serial.println("Sending bridge's shutdown command"); - } else { // any other key pressed? - Serial1.write('~'); // write '~' to Linino - Serial1.write(c); // write char to Linino - } - commandMode = false; // in all cases exit from command mode - } - } - if (Serial1.available()) { // got anything from Linino? - char c = (char)Serial1.read(); // read from Linino - Serial.write(c); // write to USB-serial - } -} \ No newline at end of file -- cgit v1.2.3-18-g5258