From 0d9a111face4f3629bcae8e52af843792af3b453 Mon Sep 17 00:00:00 2001 From: "David A. Mellis" Date: Thu, 13 Sep 2012 10:41:16 -0400 Subject: Moving into firmwares directory. --- .../src/SOFTWARE_FRAMEWORK/DRIVERS/GPIO/gpio.h | 583 +++++++++++++++++++++ 1 file changed, 583 insertions(+) create mode 100644 firmwares/wifishield/wifi_dnld/src/SOFTWARE_FRAMEWORK/DRIVERS/GPIO/gpio.h (limited to 'firmwares/wifishield/wifi_dnld/src/SOFTWARE_FRAMEWORK/DRIVERS/GPIO/gpio.h') diff --git a/firmwares/wifishield/wifi_dnld/src/SOFTWARE_FRAMEWORK/DRIVERS/GPIO/gpio.h b/firmwares/wifishield/wifi_dnld/src/SOFTWARE_FRAMEWORK/DRIVERS/GPIO/gpio.h new file mode 100644 index 0000000..f0b5fd8 --- /dev/null +++ b/firmwares/wifishield/wifi_dnld/src/SOFTWARE_FRAMEWORK/DRIVERS/GPIO/gpio.h @@ -0,0 +1,583 @@ +/* This header file is part of the ATMEL AVR-UC3-SoftwareFramework-1.7.0 Release */ + +/*This file has been prepared for Doxygen automatic documentation generation.*/ +/*! \file ********************************************************************* + * + * \brief GPIO header for AVR32 UC3. + * + * This file contains basic GPIO driver functions. + * + * - Compiler: IAR EWAVR32 and GNU GCC for AVR32 + * - Supported devices: All AVR32 devices with a GPIO module can be used. + * - AppNote: + * + * \author Atmel Corporation: http://www.atmel.com \n + * Support and FAQ: http://support.atmel.no/ + * + *****************************************************************************/ + +/* Copyright (c) 2009 Atmel Corporation. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright notice, this + * list of conditions and the following disclaimer. + * + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * + * 3. The name of Atmel may not be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * 4. This software may only be redistributed and used in connection with an Atmel + * AVR product. + * + * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE + * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR + * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES + * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; + * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND + * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS + * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE + * + */ + +#ifndef _GPIO_H_ +#define _GPIO_H_ + +#include +#include "compiler.h" + +/*! \name Return Values of the GPIO API + */ +//! @{ +#define GPIO_SUCCESS 0 //!< Function successfully completed. +#define GPIO_INVALID_ARGUMENT 1 //!< Input parameters are out of range. +//! @} + + +/*! \name Interrupt Trigger Modes + */ +//! @{ +#define GPIO_PIN_CHANGE 0 //!< Interrupt triggered upon pin change. +#define GPIO_RISING_EDGE 1 //!< Interrupt triggered upon rising edge. +#define GPIO_FALLING_EDGE 2 //!< Interrupt triggered upon falling edge. +//! @} + + +//! A type definition of pins and modules connectivity. +typedef struct +{ + unsigned char pin; //!< Module pin. + unsigned char function; //!< Module function. +} gpio_map_t[]; + + +/*! \name Peripheral Bus Interface + * + * Low-speed interface with a non-deterministic number of clock cycles per + * access. + * + * This interface operates with lower clock frequencies (fPB <= fCPU), and its + * timing is not deterministic since it needs to access a shared bus which may + * be heavily loaded. + * + * \note This interface is immediately available without initialization. + */ +//! @{ + +/*! \brief Enables specific module modes for a set of pins. + * + * \param gpiomap The pin map. + * \param size The number of pins in \a gpiomap. + * + * \return \ref GPIO_SUCCESS or \ref GPIO_INVALID_ARGUMENT. + */ +extern int gpio_enable_module(const gpio_map_t gpiomap, unsigned int size); + +/*! \brief Enables a specific module mode for a pin. + * + * \param pin The pin number.\n + * Refer to the product header file `uc3x.h' (where x is the part + * number; e.g. x = a0512) for module pins. E.g., to enable a PWM + * channel output, the pin number can be AVR32_PWM_3_PIN for PWM + * channel 3. + * \param function The pin function.\n + * Refer to the product header file `uc3x.h' (where x is the + * part number; e.g. x = a0512) for module pin functions. E.g., + * to enable a PWM channel output, the pin function can be + * AVR32_PWM_3_FUNCTION for PWM channel 3. + * + * \return \ref GPIO_SUCCESS or \ref GPIO_INVALID_ARGUMENT. + */ +extern int gpio_enable_module_pin(unsigned int pin, unsigned int function); + +/*! \brief Enables the GPIO mode of a set of pins. + * + * \param gpiomap The pin map. + * \param size The number of pins in \a gpiomap. + */ +extern void gpio_enable_gpio(const gpio_map_t gpiomap, unsigned int size); + +/*! \brief Enables the GPIO mode of a pin. + * + * \param pin The pin number.\n + * Refer to the product header file `uc3x.h' (where x is the part + * number; e.g. x = a0512) for pin definitions. E.g., to enable the + * GPIO mode of PX21, AVR32_PIN_PX21 can be used. Module pins such as + * AVR32_PWM_3_PIN for PWM channel 3 can also be used to release + * module pins for GPIO. + */ +extern void gpio_enable_gpio_pin(unsigned int pin); + +// The open-drain mode is not synthesized on the current AVR32 products. +// If one day some AVR32 products have this feature, the corresponding part +// numbers should be listed in the #if below. +// Note that other functions are available in this driver to use pins with open +// drain in GPIO mode. The advantage of the open-drain mode functions over these +// other functions is that they can be used not only in GPIO mode but also in +// module mode. +#if 0 + +/*! \brief Enables the open-drain mode of a pin. + * + * \param pin The pin number. + */ +extern void gpio_enable_pin_open_drain(unsigned int pin); + +/*! \brief Disables the open-drain mode of a pin. + * + * \param pin The pin number. + */ +extern void gpio_disable_pin_open_drain(unsigned int pin); + +#endif + +/*! \brief Enables the pull-up resistor of a pin. + * + * \param pin The pin number. + */ +extern void gpio_enable_pin_pull_up(unsigned int pin); + +/*! \brief Disables the pull-up resistor of a pin. + * + * \param pin The pin number. + */ +extern void gpio_disable_pin_pull_up(unsigned int pin); + +#if defined(AVR32_GPIO_200_H_INCLUDED) || defined(AVR32_GPIO_210_H_INCLUDED) || defined(AVR32_GPIO_211_H_INCLUDED) +// Added support of Pull-up Resistor, Pull-down Resistor and Buskeeper Control. + +/*! \brief Enables the pull-down resistor of a pin. + * + * \param pin The pin number. + */ +extern void gpio_enable_pin_pull_down(unsigned int pin); + +/*! \brief Disables the pull-down resistor of a pin. + * + * \param pin The pin number. + */ +extern void gpio_disable_pin_pull_down(unsigned int pin); + +/*! \brief Enables the buskeeper functionality on a pin. + * + * \param pin The pin number. + */ +extern void gpio_enable_pin_buskeeper(unsigned int pin); + +/*! \brief Disables the buskeeper functionality on a pin. + * + * \param pin The pin number. + */ +extern void gpio_disable_pin_buskeeper(unsigned int pin); + +#endif + +/*! \brief Returns the value of a pin. + * + * \param pin The pin number. + * + * \return The pin value. + */ +extern int gpio_get_pin_value(unsigned int pin); + +/*! \brief Returns the output value set for a GPIO pin. + * + * \param pin The pin number. + * + * \return The pin output value. + * + * \note This function must be used in conjunction with \ref gpio_set_gpio_pin, + * \ref gpio_clr_gpio_pin and \ref gpio_tgl_gpio_pin. + */ +extern int gpio_get_gpio_pin_output_value(unsigned int pin); + +/*! \brief Returns the output value set for a GPIO pin using open drain. + * + * \param pin The pin number. + * + * \return The pin output value. + * + * \note This function must be used in conjunction with + * \ref gpio_set_gpio_open_drain_pin, \ref gpio_clr_gpio_open_drain_pin + * and \ref gpio_tgl_gpio_open_drain_pin. + */ +extern int gpio_get_gpio_open_drain_pin_output_value(unsigned int pin); + +/*! \brief Drives a GPIO pin to 1. + * + * \param pin The pin number. + */ +extern void gpio_set_gpio_pin(unsigned int pin); + +/*! \brief Drives a GPIO pin to 0. + * + * \param pin The pin number. + */ +extern void gpio_clr_gpio_pin(unsigned int pin); + +/*! \brief Toggles a GPIO pin. + * + * \param pin The pin number. + */ +extern void gpio_tgl_gpio_pin(unsigned int pin); + +/*! \brief Drives a GPIO pin to 1 using open drain. + * + * \param pin The pin number. + */ +extern void gpio_set_gpio_open_drain_pin(unsigned int pin); + +/*! \brief Drives a GPIO pin to 0 using open drain. + * + * \param pin The pin number. + */ +extern void gpio_clr_gpio_open_drain_pin(unsigned int pin); + +/*! \brief Toggles a GPIO pin using open drain. + * + * \param pin The pin number. + */ +extern void gpio_tgl_gpio_open_drain_pin(unsigned int pin); + +/*! \brief Enables the glitch filter of a pin. + * + * When the glitch filter is enabled, a glitch with duration of less than 1 + * clock cycle is automatically rejected, while a pulse with duration of 2 clock + * cycles or more is accepted. For pulse durations between 1 clock cycle and 2 + * clock cycles, the pulse may or may not be taken into account, depending on + * the precise timing of its occurrence. Thus for a pulse to be guaranteed + * visible it must exceed 2 clock cycles, whereas for a glitch to be reliably + * filtered out, its duration must not exceed 1 clock cycle. The filter + * introduces 2 clock cycles latency. + * + * \param pin The pin number. + */ +extern void gpio_enable_pin_glitch_filter(unsigned int pin); + +/*! \brief Disables the glitch filter of a pin. + * + * \param pin The pin number. + */ +extern void gpio_disable_pin_glitch_filter(unsigned int pin); + +/*! \brief Enables the interrupt of a pin with the specified settings. + * + * \param pin The pin number. + * \param mode The trigger mode (\ref GPIO_PIN_CHANGE, \ref GPIO_RISING_EDGE or + * \ref GPIO_FALLING_EDGE). + * + * \return \ref GPIO_SUCCESS or \ref GPIO_INVALID_ARGUMENT. + */ +extern int gpio_enable_pin_interrupt(unsigned int pin, unsigned int mode); + +/*! \brief Disables the interrupt of a pin. + * + * \param pin The pin number. + */ +extern void gpio_disable_pin_interrupt(unsigned int pin); + +/*! \brief Gets the interrupt flag of a pin. + * + * \param pin The pin number. + * + * \return The pin interrupt flag. + */ +extern int gpio_get_pin_interrupt_flag(unsigned int pin); + +/*! \brief Clears the interrupt flag of a pin. + * + * \param pin The pin number. + */ +extern void gpio_clear_pin_interrupt_flag(unsigned int pin); + +//! @} + + +#if (defined AVR32_GPIO_LOCAL_ADDRESS) +/*! \name Local Bus Interface + * + * High-speed interface with only one clock cycle per access. + * + * This interface operates with high clock frequency (fCPU), and its timing is + * deterministic since it does not need to access a shared bus which may be + * heavily loaded. + * + * \warning To use this interface, the clock frequency of the peripheral bus on + * which the GPIO peripheral is connected must be set to the CPU clock + * frequency (fPB = fCPU). + * + * \note This interface has to be initialized in order to be available. + */ +//! @{ + +/*! \brief Enables the local bus interface for GPIO. + * + * \note This function must have been called at least once before using other + * functions in this interface. + */ +#if (defined __GNUC__) +__attribute__((__always_inline__)) +#endif +extern __inline__ void gpio_local_init(void) +{ + Set_system_register(AVR32_CPUCR, + Get_system_register(AVR32_CPUCR) | AVR32_CPUCR_LOCEN_MASK); +} + +/*! \brief Enables the output driver of a pin. + * + * \param pin The pin number. + * + * \note \ref gpio_local_init must have been called beforehand. + * + * \note This function does not enable the GPIO mode of the pin. + * \ref gpio_enable_gpio_pin can be called for this purpose. + */ +#if (defined __GNUC__) +__attribute__((__always_inline__)) +#endif +extern __inline__ void gpio_local_enable_pin_output_driver(unsigned int pin) +{ + AVR32_GPIO_LOCAL.port[pin >> 5].oders = 1 << (pin & 0x1F); +} + +/*! \brief Disables the output driver of a pin. + * + * \param pin The pin number. + * + * \note \ref gpio_local_init must have been called beforehand. + */ +#if (defined __GNUC__) +__attribute__((__always_inline__)) +#endif +extern __inline__ void gpio_local_disable_pin_output_driver(unsigned int pin) +{ + AVR32_GPIO_LOCAL.port[pin >> 5].oderc = 1 << (pin & 0x1F); +} + +/*! \brief Returns the value of a pin. + * + * \param pin The pin number. + * + * \return The pin value. + * + * \note \ref gpio_local_init must have been called beforehand. + */ +#if (defined __GNUC__) +__attribute__((__always_inline__)) +#endif +extern __inline__ int gpio_local_get_pin_value(unsigned int pin) +{ + return (AVR32_GPIO_LOCAL.port[pin >> 5].pvr >> (pin & 0x1F)) & 1; +} + +/*! \brief Drives a GPIO pin to 1. + * + * \param pin The pin number. + * + * \note \ref gpio_local_init must have been called beforehand. + * + * \note This function does not enable the GPIO mode of the pin nor its output + * driver. \ref gpio_enable_gpio_pin and + * \ref gpio_local_enable_pin_output_driver can be called for this + * purpose. + */ +#if (defined __GNUC__) +__attribute__((__always_inline__)) +#endif +extern __inline__ void gpio_local_set_gpio_pin(unsigned int pin) +{ + AVR32_GPIO_LOCAL.port[pin >> 5].ovrs = 1 << (pin & 0x1F); +} + +/*! \brief Drives a GPIO pin to 0. + * + * \param pin The pin number. + * + * \note \ref gpio_local_init must have been called beforehand. + * + * \note This function does not enable the GPIO mode of the pin nor its output + * driver. \ref gpio_enable_gpio_pin and + * \ref gpio_local_enable_pin_output_driver can be called for this + * purpose. + */ +#if (defined __GNUC__) +__attribute__((__always_inline__)) +#endif +extern __inline__ void gpio_local_clr_gpio_pin(unsigned int pin) +{ + AVR32_GPIO_LOCAL.port[pin >> 5].ovrc = 1 << (pin & 0x1F); +} + +/*! \brief Toggles a GPIO pin. + * + * \param pin The pin number. + * + * \note \ref gpio_local_init must have been called beforehand. + * + * \note This function does not enable the GPIO mode of the pin nor its output + * driver. \ref gpio_enable_gpio_pin and + * \ref gpio_local_enable_pin_output_driver can be called for this + * purpose. + */ +#if (defined __GNUC__) +__attribute__((__always_inline__)) +#endif +extern __inline__ void gpio_local_tgl_gpio_pin(unsigned int pin) +{ + AVR32_GPIO_LOCAL.port[pin >> 5].ovrt = 1 << (pin & 0x1F); +} + +/*! \brief Initializes the configuration of a GPIO pin so that it can be used + * with GPIO open-drain functions. + * + * \note This function must have been called at least once before using + * \ref gpio_local_set_gpio_open_drain_pin, + * \ref gpio_local_clr_gpio_open_drain_pin or + * \ref gpio_local_tgl_gpio_open_drain_pin. + */ +#if (defined __GNUC__) +__attribute__((__always_inline__)) +#endif +extern __inline__ void gpio_local_init_gpio_open_drain_pin(unsigned int pin) +{ + AVR32_GPIO_LOCAL.port[pin >> 5].ovrc = 1 << (pin & 0x1F); +} + +/*! \brief Drives a GPIO pin to 1 using open drain. + * + * \param pin The pin number. + * + * \note \ref gpio_local_init and \ref gpio_local_init_gpio_open_drain_pin must + * have been called beforehand. + * + * \note This function does not enable the GPIO mode of the pin. + * \ref gpio_enable_gpio_pin can be called for this purpose. + */ +#if (defined __GNUC__) +__attribute__((__always_inline__)) +#endif +extern __inline__ void gpio_local_set_gpio_open_drain_pin(unsigned int pin) +{ + AVR32_GPIO_LOCAL.port[pin >> 5].oderc = 1 << (pin & 0x1F); +} + +/*! \brief Drives a GPIO pin to 0 using open drain. + * + * \param pin The pin number. + * + * \note \ref gpio_local_init and \ref gpio_local_init_gpio_open_drain_pin must + * have been called beforehand. + * + * \note This function does not enable the GPIO mode of the pin. + * \ref gpio_enable_gpio_pin can be called for this purpose. + */ +#if (defined __GNUC__) +__attribute__((__always_inline__)) +#endif +extern __inline__ void gpio_local_clr_gpio_open_drain_pin(unsigned int pin) +{ + AVR32_GPIO_LOCAL.port[pin >> 5].oders = 1 << (pin & 0x1F); +} + +/*! \brief Toggles a GPIO pin using open drain. + * + * \param pin The pin number. + * + * \note \ref gpio_local_init and \ref gpio_local_init_gpio_open_drain_pin must + * have been called beforehand. + * + * \note This function does not enable the GPIO mode of the pin. + * \ref gpio_enable_gpio_pin can be called for this purpose. + */ +#if (defined __GNUC__) +__attribute__((__always_inline__)) +#endif +extern __inline__ void gpio_local_tgl_gpio_open_drain_pin(unsigned int pin) +{ + AVR32_GPIO_LOCAL.port[pin >> 5].odert = 1 << (pin & 0x1F); +} + +//! @} +#endif // AVR32_GPIO_LOCAL_ADDRESS + +#if UC3L +//! @{ +/*! \name Peripheral Event System support + * + * The GPIO can be programmed to output peripheral events whenever an interrupt + * condition is detected, such as pin value change, or only when a rising or + * falling edge is detected. + * + */ + +/*! \brief Enables the peripheral event generation of a pin. + * + * \param pin The pin number. + * + */ +#if (defined __GNUC__) +__attribute__((__always_inline__)) +#endif +extern __inline__ void gpio_enable_pin_periph_event(unsigned int pin) +{ + AVR32_GPIO.port[pin >> 5].oderc = 1 << (pin & 0x1F); // The GPIO output driver is disabled for that pin. + AVR32_GPIO.port[pin >> 5].evers = 1 << (pin & 0x1F); +} + +/*! \brief Disables the peripheral event generation of a pin. + * + * \param pin The pin number. + * + */ +#if (defined __GNUC__) +__attribute__((__always_inline__)) +#endif +extern __inline__ void gpio_disable_pin_periph_event(unsigned int pin) +{ + AVR32_GPIO.port[pin >> 5].everc = 1 << (pin & 0x1F); +} + +/*! \brief Configure the peripheral event trigger mode of a pin + * + * \param pin The pin number. + * \param mode The trigger mode (\ref GPIO_PIN_CHANGE, \ref GPIO_RISING_EDGE or + * \ref GPIO_FALLING_EDGE). + * \param use_igf use the Input Glitch Filter (TRUE) or not (FALSE). + * + * \return \ref GPIO_SUCCESS or \ref GPIO_INVALID_ARGUMENT. + */ +extern int gpio_configure_pin_periph_event_mode(unsigned int pin, unsigned int mode, unsigned int use_igf); + +//! @} +#endif + + +#endif // _GPIO_H_ -- cgit v1.2.3-18-g5258