From 6225a8596005bfb0be68fa641f5b47d01a95c12d Mon Sep 17 00:00:00 2001 From: "David A. Mellis" Date: Thu, 13 Sep 2012 10:39:59 -0400 Subject: Moving ATmegaXXU2 firmwares into subdirectory. --- firmwares/arduino-usbserial/makefile | 776 ----------------------------------- 1 file changed, 776 deletions(-) delete mode 100755 firmwares/arduino-usbserial/makefile (limited to 'firmwares/arduino-usbserial/makefile') diff --git a/firmwares/arduino-usbserial/makefile b/firmwares/arduino-usbserial/makefile deleted file mode 100755 index 79d6be2..0000000 --- a/firmwares/arduino-usbserial/makefile +++ /dev/null @@ -1,776 +0,0 @@ -# Hey Emacs, this is a -*- makefile -*- -#---------------------------------------------------------------------------- -# WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al. -# >> Modified for use with the LUFA project. << -# -# Released to the Public Domain -# -# Additional material for this makefile was written by: -# Peter Fleury -# Tim Henigan -# Colin O'Flynn -# Reiner Patommel -# Markus Pfaff -# Sander Pool -# Frederik Rouleau -# Carlos Lamas -# Dean Camera -# Opendous Inc. -# Denver Gingerich -# -#---------------------------------------------------------------------------- -# On command line: -# -# make all = Make software. -# -# make clean = Clean out built project files. -# -# make coff = Convert ELF to AVR COFF. -# -# make extcoff = Convert ELF to AVR Extended COFF. -# -# make program = Download the hex file to the device, using avrdude. -# Please customize the avrdude settings below first! -# -# make dfu = Download the hex file to the device, using dfu-programmer (must -# have dfu-programmer installed). -# -# make flip = Download the hex file to the device, using Atmel FLIP (must -# have Atmel FLIP installed). -# -# make dfu-ee = Download the eeprom file to the device, using dfu-programmer -# (must have dfu-programmer installed). -# -# make flip-ee = Download the eeprom file to the device, using Atmel FLIP -# (must have Atmel FLIP installed). -# -# make doxygen = Generate DoxyGen documentation for the project (must have -# DoxyGen installed) -# -# make debug = Start either simulavr or avarice as specified for debugging, -# with avr-gdb or avr-insight as the front end for debugging. -# -# make filename.s = Just compile filename.c into the assembler code only. -# -# make filename.i = Create a preprocessed source file for use in submitting -# bug reports to the GCC project. -# -# To rebuild project do "make clean" then "make all". -#---------------------------------------------------------------------------- - -# MCU name(s) -# Since the ATMEGA8U2 part is not directly supported by the current -# versions of either avrdude or dfu-programmer, we specify a dummy -# part; AT90USB82 which is close enough in memory size and organization -MCU = atmega8u2 -MCU_AVRDUDE = at90usb82 -MCU_DFU = at90usb82 - -# Specify the Arduino model using the assigned PID. This is used by Descriptors.c -# to set PID and product descriptor string -# Uno PID: -ARDUINO_MODEL_PID = 0x0001 -# Mega 2560 PID: -#ARDUINO_MODEL_PID = 0x0010 - - -# Target board (see library "Board Types" documentation, NONE for projects not requiring -# LUFA board drivers). If USER is selected, put custom board drivers in a directory called -# "Board" inside the application directory. -BOARD = USER - - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_CLOCK below, as it is sourced by -# F_CLOCK after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# Input clock frequency. -# This will define a symbol, F_CLOCK, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_CLOCK = $(F_CPU) - - -# Output format. (can be srec, ihex, binary) -FORMAT = ihex - - -# Target file name (without extension). -TARGET = Arduino-usbserial - - -# Object files directory -# To put object files in current directory, use a dot (.), do NOT make -# this an empty or blank macro! -OBJDIR = . - - -# Path to the LUFA library -LUFA_PATH = ../.. - - -# LUFA library compile-time options -LUFA_OPTS = -D USB_DEVICE_ONLY -LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8 -LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1 -LUFA_OPTS += -D USE_FLASH_DESCRIPTORS -LUFA_OPTS += -D INTERRUPT_CONTROL_ENDPOINT -LUFA_OPTS += -D DEVICE_STATE_AS_GPIOR=0 -LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)" - - -# Create the LUFA source path variables by including the LUFA root makefile -include $(LUFA_PATH)/LUFA/makefile - - -# List C source files here. (C dependencies are automatically generated.) -SRC = $(TARGET).c \ - Descriptors.c \ - $(LUFA_SRC_USB) \ - $(LUFA_SRC_USBCLASS) \ - $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/Device.c \ - $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/Endpoint.c \ - $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/HostStandardReq.c \ - $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/Host.c \ - $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/Pipe.c \ - $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/USBController.c \ - $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/Events.c \ - $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/USBInterrupt.c \ - $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/USBTask.c \ - $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/DeviceStandardReq.c \ - $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/ConfigDescriptor.c \ - $(LUFA_PATH)/LUFA/Drivers/USB/Class/Device/CDC.c \ - $(LUFA_PATH)/LUFA/Drivers/USB/Class/Host/CDC.c - - -# List C++ source files here. (C dependencies are automatically generated.) -CPPSRC = - - -# List Assembler source files here. -# Make them always end in a capital .S. Files ending in a lowercase .s -# will not be considered source files but generated files (assembler -# output from the compiler), and will be deleted upon "make clean"! -# Even though the DOS/Win* filesystem matches both .s and .S the same, -# it will preserve the spelling of the filenames, and gcc itself does -# care about how the name is spelled on its command-line. -ASRC = - - -# Optimization level, can be [0, 1, 2, 3, s]. -# 0 = turn off optimization. s = optimize for size. -# (Note: 3 is not always the best optimization level. See avr-libc FAQ.) -OPT = s - - -# Debugging format. -# Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs. -# AVR Studio 4.10 requires dwarf-2. -# AVR [Extended] COFF format requires stabs, plus an avr-objcopy run. -DEBUG = dwarf-2 - - -# List any extra directories to look for include files here. -# Each directory must be seperated by a space. -# Use forward slashes for directory separators. -# For a directory that has spaces, enclose it in quotes. -EXTRAINCDIRS = $(LUFA_PATH)/ - - -# Compiler flag to set the C Standard level. -# c89 = "ANSI" C -# gnu89 = c89 plus GCC extensions -# c99 = ISO C99 standard (not yet fully implemented) -# gnu99 = c99 plus GCC extensions -CSTANDARD = -std=gnu99 - - -# Place -D or -U options here for C sources -CDEFS = -DF_CPU=$(F_CPU)UL -CDEFS += -DF_CLOCK=$(F_CLOCK)UL -CDEFS += -DARDUINO_MODEL_PID=$(ARDUINO_MODEL_PID) -CDEFS += -DBOARD=BOARD_$(BOARD) -CDEFS += $(LUFA_OPTS) -CDEFS += -DAVR_RESET_LINE_PORT="PORTD" -CDEFS += -DAVR_RESET_LINE_DDR="DDRD" -CDEFS += -DAVR_RESET_LINE_MASK="(1 << 7)" -CDEFS += -DTX_RX_LED_PULSE_MS=3 -CDEFS += -DPING_PONG_LED_PULSE_MS=100 - -# Place -D or -U options here for ASM sources -ADEFS = -DF_CPU=$(F_CPU) -ADEFS += -DF_CLOCK=$(F_CLOCK)UL -ADEFS += -DBOARD=BOARD_$(BOARD) -ADEFS += $(LUFA_OPTS) - -# Place -D or -U options here for C++ sources -CPPDEFS = -DF_CPU=$(F_CPU)UL -CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL -CPPDEFS += -DBOARD=BOARD_$(BOARD) -CPPDEFS += $(LUFA_OPTS) -#CPPDEFS += -D__STDC_LIMIT_MACROS -#CPPDEFS += -D__STDC_CONSTANT_MACROS - - - -#---------------- Compiler Options C ---------------- -# -g*: generate debugging information -# -O*: optimization level -# -f...: tuning, see GCC manual and avr-libc documentation -# -Wall...: warning level -# -Wa,...: tell GCC to pass this to the assembler. -# -adhlns...: create assembler listing -CFLAGS = -g$(DEBUG) -CFLAGS += $(CDEFS) -CFLAGS += -O$(OPT) -CFLAGS += -funsigned-char -CFLAGS += -funsigned-bitfields -CFLAGS += -ffunction-sections -CFLAGS += -fno-inline-small-functions -CFLAGS += -fpack-struct -CFLAGS += -fshort-enums -CFLAGS += -fno-strict-aliasing -CFLAGS += -Wall -CFLAGS += -Wstrict-prototypes -#CFLAGS += -mshort-calls -#CFLAGS += -fno-unit-at-a-time -#CFLAGS += -Wundef -#CFLAGS += -Wunreachable-code -#CFLAGS += -Wsign-compare -CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst) -CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS)) -CFLAGS += $(CSTANDARD) - - -#---------------- Compiler Options C++ ---------------- -# -g*: generate debugging information -# -O*: optimization level -# -f...: tuning, see GCC manual and avr-libc documentation -# -Wall...: warning level -# -Wa,...: tell GCC to pass this to the assembler. -# -adhlns...: create assembler listing -CPPFLAGS = -g$(DEBUG) -CPPFLAGS += $(CPPDEFS) -CPPFLAGS += -O$(OPT) -CPPFLAGS += -funsigned-char -CPPFLAGS += -funsigned-bitfields -CPPFLAGS += -fpack-struct -CPPFLAGS += -fshort-enums -CPPFLAGS += -fno-exceptions -CPPFLAGS += -Wall -CPPFLAGS += -Wundef -CFLAGS += -Wundef -#CPPFLAGS += -mshort-calls -#CPPFLAGS += -fno-unit-at-a-time -#CPPFLAGS += -Wstrict-prototypes -#CPPFLAGS += -Wunreachable-code -#CPPFLAGS += -Wsign-compare -CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst) -CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS)) -#CPPFLAGS += $(CSTANDARD) - - -#---------------- Assembler Options ---------------- -# -Wa,...: tell GCC to pass this to the assembler. -# -adhlns: create listing -# -gstabs: have the assembler create line number information; note that -# for use in COFF files, additional information about filenames -# and function names needs to be present in the assembler source -# files -- see avr-libc docs [FIXME: not yet described there] -# -listing-cont-lines: Sets the maximum number of continuation lines of hex -# dump that will be displayed for a given single line of source input. -ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100 - - -#---------------- Library Options ---------------- -# Minimalistic printf version -PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min - -# Floating point printf version (requires MATH_LIB = -lm below) -PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt - -# If this is left blank, then it will use the Standard printf version. -PRINTF_LIB = -#PRINTF_LIB = $(PRINTF_LIB_MIN) -#PRINTF_LIB = $(PRINTF_LIB_FLOAT) - - -# Minimalistic scanf version -SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min - -# Floating point + %[ scanf version (requires MATH_LIB = -lm below) -SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt - -# If this is left blank, then it will use the Standard scanf version. -SCANF_LIB = -#SCANF_LIB = $(SCANF_LIB_MIN) -#SCANF_LIB = $(SCANF_LIB_FLOAT) - - -MATH_LIB = -lm - - -# List any extra directories to look for libraries here. -# Each directory must be seperated by a space. -# Use forward slashes for directory separators. -# For a directory that has spaces, enclose it in quotes. -EXTRALIBDIRS = - - - -#---------------- External Memory Options ---------------- - -# 64 KB of external RAM, starting after internal RAM (ATmega128!), -# used for variables (.data/.bss) and heap (malloc()). -#EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff - -# 64 KB of external RAM, starting after internal RAM (ATmega128!), -# only used for heap (malloc()). -#EXTMEMOPTS = -Wl,--section-start,.data=0x801100,--defsym=__heap_end=0x80ffff - -EXTMEMOPTS = - - - -#---------------- Linker Options ---------------- -# -Wl,...: tell GCC to pass this to linker. -# -Map: create map file -# --cref: add cross reference to map file -LDFLAGS = -Wl,-Map=$(TARGET).map,--cref -LDFLAGS += -Wl,--relax -LDFLAGS += -Wl,--gc-sections -LDFLAGS += $(EXTMEMOPTS) -LDFLAGS += $(patsubst %,-L%,$(EXTRALIBDIRS)) -LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB) -#LDFLAGS += -T linker_script.x - - - -#---------------- Programming Options (avrdude) ---------------- - -# Programming hardware -# Type: avrdude -c ? -# to get a full listing. -# -AVRDUDE_PROGRAMMER = avrispmkii - -# com1 = serial port. Use lpt1 to connect to parallel port. -AVRDUDE_PORT = usb - -AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex -#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep - - -# Uncomment the following if you want avrdude's erase cycle counter. -# Note that this counter needs to be initialized first using -Yn, -# see avrdude manual. -#AVRDUDE_ERASE_COUNTER = -y - -# Uncomment the following if you do /not/ wish a verification to be -# performed after programming the device. -#AVRDUDE_NO_VERIFY = -V - -# Increase verbosity level. Please use this when submitting bug -# reports about avrdude. See -# to submit bug reports. -#AVRDUDE_VERBOSE = -v -v - -AVRDUDE_FORCE = -F - -AVRDUDE_FLAGS = -p $(MCU_AVRDUDE) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) -AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY) -AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE) -AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER) -AVRDUDE_FLAGS += $(AVRDUDE_FORCE) - - - -#---------------- Debugging Options ---------------- - -# For simulavr only - target MCU frequency. -DEBUG_MFREQ = $(F_CPU) - -# Set the DEBUG_UI to either gdb or insight. -# DEBUG_UI = gdb -DEBUG_UI = insight - -# Set the debugging back-end to either avarice, simulavr. -DEBUG_BACKEND = avarice -#DEBUG_BACKEND = simulavr - -# GDB Init Filename. -GDBINIT_FILE = __avr_gdbinit - -# When using avarice settings for the JTAG -JTAG_DEV = /dev/com1 - -# Debugging port used to communicate between GDB / avarice / simulavr. -DEBUG_PORT = 4242 - -# Debugging host used to communicate between GDB / avarice / simulavr, normally -# just set to localhost unless doing some sort of crazy debugging when -# avarice is running on a different computer. -DEBUG_HOST = localhost - - - -#============================================================================ - - -# Define programs and commands. -SHELL = sh -CC = avr-gcc -OBJCOPY = avr-objcopy -OBJDUMP = avr-objdump -SIZE = avr-size -AR = avr-ar rcs -NM = avr-nm -AVRDUDE = avrdude -REMOVE = rm -f -REMOVEDIR = rm -rf -COPY = cp -WINSHELL = cmd - -# Define Messages -# English -MSG_ERRORS_NONE = Errors: none -MSG_BEGIN = -------- begin -------- -MSG_END = -------- end -------- -MSG_SIZE_BEFORE = Size before: -MSG_SIZE_AFTER = Size after: -MSG_COFF = Converting to AVR COFF: -MSG_EXTENDED_COFF = Converting to AVR Extended COFF: -MSG_FLASH = Creating load file for Flash: -MSG_EEPROM = Creating load file for EEPROM: -MSG_EXTENDED_LISTING = Creating Extended Listing: -MSG_SYMBOL_TABLE = Creating Symbol Table: -MSG_LINKING = Linking: -MSG_COMPILING = Compiling C: -MSG_COMPILING_CPP = Compiling C++: -MSG_ASSEMBLING = Assembling: -MSG_CLEANING = Cleaning project: -MSG_CREATING_LIBRARY = Creating library: - - - - -# Define all object files. -OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o) - -# Define all listing files. -LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst) - - -# Compiler flags to generate dependency files. -GENDEPFLAGS = -MMD -MP -MF .dep/$(@F).d - - -# Combine all necessary flags and optional flags. -# Add target processor to flags. -ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS) -ALL_CPPFLAGS = -mmcu=$(MCU) -I. -x c++ $(CPPFLAGS) $(GENDEPFLAGS) -ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS) - - - - - -# Default target. -#all: begin gccversion sizebefore build checkinvalidevents showliboptions showtarget sizeafter end -all: begin gccversion sizebefore build showliboptions showtarget sizeafter end - -# Change the build target to build a HEX file or a library. -build: elf hex eep lss sym asm -#build: lib - - -elf: $(TARGET).elf -hex: $(TARGET).hex -eep: $(TARGET).eep -lss: $(TARGET).lss -sym: $(TARGET).sym -asm: $(TARGET).s -LIBNAME=lib$(TARGET).a -lib: $(LIBNAME) - - - -# Eye candy. -# AVR Studio 3.x does not check make's exit code but relies on -# the following magic strings to be generated by the compile job. -begin: - @echo - @echo $(MSG_BEGIN) - -end: - @echo $(MSG_END) - @echo - - -# Display size of file. -HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex -ELFSIZE = $(SIZE) $(MCU_FLAG) $(FORMAT_FLAG) $(TARGET).elf -MCU_FLAG = $(shell $(SIZE) --help | grep -- --mcu > /dev/null && echo --mcu=$(MCU) ) -FORMAT_FLAG = $(shell $(SIZE) --help | grep -- --format=.*avr > /dev/null && echo --format=avr ) - -sizebefore: - @if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \ - 2>/dev/null; echo; fi - -sizeafter: - @if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \ - 2>/dev/null; echo; fi - -#$(LUFA_PATH)/LUFA/LUFA_Events.lst: -# @make -C $(LUFA_PATH)/LUFA/ LUFA_Events.lst - -#checkinvalidevents: $(LUFA_PATH)/LUFA/LUFA_Events.lst -# @echo -# @echo Checking for invalid events... -# @$(shell) avr-nm $(OBJ) | sed -n -e 's/^.*EVENT_/EVENT_/p' | \ -# grep -F -v --file=$(LUFA_PATH)/LUFA/LUFA_Events.lst > InvalidEvents.tmp || true -# @sed -n -e 's/^/ WARNING - INVALID EVENT NAME: /p' InvalidEvents.tmp -# @if test -s InvalidEvents.tmp; then exit 1; fi - -showliboptions: - @echo - @echo ---- Compile Time Library Options ---- - @for i in $(LUFA_OPTS:-D%=%); do \ - echo $$i; \ - done - @echo -------------------------------------- - -showtarget: - @echo - @echo --------- Target Information --------- - @echo AVR Model: $(MCU) - @echo Board: $(BOARD) - @echo Clock: $(F_CPU)Hz CPU, $(F_CLOCK)Hz Master - @echo -------------------------------------- - - -# Display compiler version information. -gccversion : - @$(CC) --version - - -# Program the device. -program: $(TARGET).hex $(TARGET).eep - $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM) - -flip: $(TARGET).hex - batchisp -hardware usb -device $(MCU_DFU) -operation erase f - batchisp -hardware usb -device $(MCU_DFU) -operation loadbuffer $(TARGET).hex program - batchisp -hardware usb -device $(MCU_DFU) -operation start reset 0 - -dfu: $(TARGET).hex - dfu-programmer $(MCU_DFU) erase - dfu-programmer $(MCU_DFU) flash --debug 1 $(TARGET).hex - dfu-programmer $(MCU_DFU) reset - - -flip-ee: $(TARGET).hex $(TARGET).eep - $(COPY) $(TARGET).eep $(TARGET)eep.hex - batchisp -hardware usb -device $(MCU_DFU) -operation memory EEPROM erase - batchisp -hardware usb -device $(MCU_DFU) -operation memory EEPROM loadbuffer $(TARGET)eep.hex program - batchisp -hardware usb -device $(MCU_DFU) -operation start reset 0 - $(REMOVE) $(TARGET)eep.hex - -dfu-ee: $(TARGET).hex $(TARGET).eep - dfu-programmer $(MCU_DFU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep - dfu-programmer $(MCU_DFU) reset - - -# Generate avr-gdb config/init file which does the following: -# define the reset signal, load the target file, connect to target, and set -# a breakpoint at main(). -gdb-config: - @$(REMOVE) $(GDBINIT_FILE) - @echo define reset >> $(GDBINIT_FILE) - @echo SIGNAL SIGHUP >> $(GDBINIT_FILE) - @echo end >> $(GDBINIT_FILE) - @echo file $(TARGET).elf >> $(GDBINIT_FILE) - @echo target remote $(DEBUG_HOST):$(DEBUG_PORT) >> $(GDBINIT_FILE) -ifeq ($(DEBUG_BACKEND),simulavr) - @echo load >> $(GDBINIT_FILE) -endif - @echo break main >> $(GDBINIT_FILE) - -debug: gdb-config $(TARGET).elf -ifeq ($(DEBUG_BACKEND), avarice) - @echo Starting AVaRICE - Press enter when "waiting to connect" message displays. - @$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \ - $(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT) - @$(WINSHELL) /c pause - -else - @$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \ - $(DEBUG_MFREQ) --port $(DEBUG_PORT) -endif - @$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE) - - - - -# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB. -COFFCONVERT = $(OBJCOPY) --debugging -COFFCONVERT += --change-section-address .data-0x800000 -COFFCONVERT += --change-section-address .bss-0x800000 -COFFCONVERT += --change-section-address .noinit-0x800000 -COFFCONVERT += --change-section-address .eeprom-0x810000 - - - -coff: $(TARGET).elf - @echo - @echo $(MSG_COFF) $(TARGET).cof - $(COFFCONVERT) -O coff-avr $< $(TARGET).cof - - -extcoff: $(TARGET).elf - @echo - @echo $(MSG_EXTENDED_COFF) $(TARGET).cof - $(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof - - - -# Create final output files (.hex, .eep) from ELF output file. -%.hex: %.elf - @echo - @echo $(MSG_FLASH) $@ - $(OBJCOPY) -O $(FORMAT) -R .eeprom -R .fuse -R .lock $< $@ - -%.eep: %.elf - @echo - @echo $(MSG_EEPROM) $@ - -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \ - --change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT) $< $@ || exit 0 - -# Create extended listing file from ELF output file. -%.lss: %.elf - @echo - @echo $(MSG_EXTENDED_LISTING) $@ - $(OBJDUMP) -h -S -z $< > $@ - -# Create a symbol table from ELF output file. -%.sym: %.elf - @echo - @echo $(MSG_SYMBOL_TABLE) $@ - $(NM) -n $< > $@ - - - -# Create library from object files. -.SECONDARY : $(TARGET).a -.PRECIOUS : $(OBJ) -%.a: $(OBJ) - @echo - @echo $(MSG_CREATING_LIBRARY) $@ - $(AR) $@ $(OBJ) - - -# Link: create ELF output file from object files. -.SECONDARY : $(TARGET).elf -.PRECIOUS : $(OBJ) -%.elf: $(OBJ) - @echo - @echo $(MSG_LINKING) $@ - $(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS) - - -# Compile: create object files from C source files. -$(OBJDIR)/%.o : %.c - @echo - @echo $(MSG_COMPILING) $< - $(CC) -c $(ALL_CFLAGS) $< -o $@ - - -# Compile: create object files from C++ source files. -$(OBJDIR)/%.o : %.cpp - @echo - @echo $(MSG_COMPILING_CPP) $< - $(CC) -c $(ALL_CPPFLAGS) $< -o $@ - - -# Compile: create assembler files from C source files. -%.s : %.c - $(CC) -S $(ALL_CFLAGS) $< -o $@ - - -# Compile: create assembler files from C++ source files. -%.s : %.cpp - $(CC) -S $(ALL_CPPFLAGS) $< -o $@ - - -# Assemble: create object files from assembler source files. -$(OBJDIR)/%.o : %.S - @echo - @echo $(MSG_ASSEMBLING) $< - $(CC) -c $(ALL_ASFLAGS) $< -o $@ - - -# Create preprocessed source for use in sending a bug report. -%.i : %.c - $(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@ - - -# Target: clean project. -clean: begin clean_list clean_binary end - -clean_binary: - $(REMOVE) $(TARGET).hex - -clean_list: - @echo $(MSG_CLEANING) - $(REMOVE) $(TARGET).hex - $(REMOVE) $(TARGET).eep - $(REMOVE) $(TARGET).cof - $(REMOVE) $(TARGET).elf - $(REMOVE) $(TARGET).map - $(REMOVE) $(TARGET).sym - $(REMOVE) $(TARGET).lss - $(REMOVE) $(SRC:%.c=$(OBJDIR)/%.o) - $(REMOVE) $(SRC:%.c=$(OBJDIR)/%.lst) - $(REMOVE) $(SRC:.c=.s) - $(REMOVE) $(SRC:.c=.d) - $(REMOVE) $(SRC:.c=.i) - $(REMOVEDIR) .dep - -doxygen: - @echo Generating Project Documentation... - @doxygen Doxygen.conf - @echo Documentation Generation Complete. - -clean_doxygen: - rm -rf Documentation - -# Create object files directory -$(shell mkdir $(OBJDIR) 2>/dev/null) - - -# Include the dependency files. --include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*) - - -# Listing of phony targets. -.PHONY : all begin finish end sizebefore sizeafter gccversion \ -build elf hex eep lss sym coff extcoff doxygen clean \ -clean_list clean_doxygen program dfu flip flip-ee dfu-ee \ -debug gdb-config -- cgit v1.2.3-18-g5258