diff options
Diffstat (limited to 'bootloaders/diskloader/src/DiskLoader.cpp')
| -rw-r--r-- | bootloaders/diskloader/src/DiskLoader.cpp | 246 |
1 files changed, 246 insertions, 0 deletions
diff --git a/bootloaders/diskloader/src/DiskLoader.cpp b/bootloaders/diskloader/src/DiskLoader.cpp new file mode 100644 index 0000000..3cb5caa --- /dev/null +++ b/bootloaders/diskloader/src/DiskLoader.cpp @@ -0,0 +1,246 @@ + + +#include "Platform.h" + +// This bootloader creates a composite Serial/Mass storage device +// +// The serial interface supports a STK500v1 protocol that is very similar to optiboot +// The mass storage interface emulates a disk image that is used to read or write firmware.bin files +// Delete firmware.bin and copy a new binary (not .hex) file to flash the firmware i.e: +// +// cp firmware.bin f:/. -f +// +// Ejecting the disk will run the firmware +// +// The bootloader will timeout and start the firmware after a few hundred milliseconds +// if a usb connection is not detected. +// +// The tweakier code is to keep the bootloader below 2k (no interrupt table, for example) + +extern "C" +void entrypoint(void) __attribute__ ((naked)) __attribute__ ((section (".vectors"))); +void entrypoint(void) +{ + asm volatile ( + "eor r1, r1\n" // Zero register + "out 0x3F, r1\n" // SREG + "ldi r28, 0xFF\n" + "ldi r29, 0x0A\n" + "out 0x3E, r29\n" // SPH + "out 0x3D, r28\n" // SPL + "rjmp main" // Stack is all set up, start the main code + ::); +} + +u8 _flashbuf[128]; +u8 _inSync; +u8 _ok; +extern volatile u8 _ejected; +extern volatile u16 _timeout; + +void Program(u8 ep, u16 page, u8 count) +{ + u8 write = page < 30*1024; // Don't write over firmware please + if (write) + boot_page_erase(page); + + Recv(ep,_flashbuf,count); // Read while page is erasing + + if (!write) + return; + + boot_spm_busy_wait(); // Wait until the memory is erased. + + count >>= 1; + u16* p = (u16*)page; + u16* b = (u16*)_flashbuf; + for (u8 i = 0; i < count; i++) + boot_page_fill(p++, b[i]); + + boot_page_write(page); + boot_spm_busy_wait(); + boot_rww_enable (); +} + + +int USBGetChar(); +#define getch USBGetChar + +#define HW_VER 0x02 +#define SW_MAJOR 0x01 +#define SW_MINOR 0x10 + +#define STK_OK 0x10 +#define STK_INSYNC 0x14 // ' ' +#define CRC_EOP 0x20 // 'SPACE' +#define STK_GET_SYNC 0x30 // '0' + +#define STK_GET_PARAMETER 0x41 // 'A' +#define STK_SET_DEVICE 0x42 // 'B' +#define STK_SET_DEVICE_EXT 0x45 // 'E' +#define STK_LOAD_ADDRESS 0x55 // 'U' +#define STK_UNIVERSAL 0x56 // 'V' +#define STK_PROG_PAGE 0x64 // 'd' +#define STK_READ_PAGE 0x74 // 't' +#define STK_READ_SIGN 0x75 // 'u' + +extern const u8 _readSize[] PROGMEM; +const u8 _readSize[] = +{ + STK_GET_PARAMETER, 1, + STK_SET_DEVICE, 20, + STK_SET_DEVICE_EXT, 5, + STK_UNIVERSAL, 4, + STK_LOAD_ADDRESS, 2, + STK_PROG_PAGE, 3, + STK_READ_PAGE, 3, + 0,0 +}; + +extern const u8 _consts[] PROGMEM; +const u8 _consts[] = +{ + SIGNATURE_0, + SIGNATURE_1, + SIGNATURE_2, + HW_VER, // Hardware version + SW_MAJOR, // Software major version + SW_MINOR, // Software minor version + 0x03, // Unknown but seems to be required by avr studio 3.56 + 0x00, // +}; + + +void USBInit(void); +extern u8 _sector3[512]; + +int main(void) __attribute__ ((naked)); + +// STK500v1 main loop, very similar to optiboot in protocol and implementation +int main() +{ + BOARD_INIT(); + USBInit(); + +#ifdef WRITABLE_DIRECTORY + _sector3[0] = 0; +#endif + + _inSync = STK_INSYNC; + _ok = STK_OK; +#ifndef MSC_ENABLED + if (pgm_read_word(0) != -1) + _ejected = 1; +#endif + for(;;) + { + u8* packet = _flashbuf; + u16 address = 0; + for (;;) + { + u8 cmd = getch(); + + // Read packet contents + u8 len; + const u8* rs = _readSize; + for(;;) + { + u8 c = pgm_read_byte(rs++); + len = pgm_read_byte(rs++); + if (c == cmd || c == 0) + break; + } +#ifndef MSC_ENABLED + _timeout = 0; +#endif + // Read params + Recv(CDC_RX,packet,len); + + // Send a response + u8 send = 0; + const u8* pgm = _consts+7; // 0 + if (STK_GET_PARAMETER == cmd) + { + u8 i = packet[0] - 0x80; + if (i > 2) + i = (i == 0x18) ? 3 : 4; // 0x80:HW_VER,0x81:SW_MAJOR,0x82:SW_MINOR,0x18:3 or 0 + pgm = _consts + i + 3; + send = 1; + } + + else if (STK_UNIVERSAL == cmd) + { + if (packet[0] == 0x30) + pgm = _consts + packet[2]; // read signature + send = 1; + } + + // Read signature bytes + else if (STK_READ_SIGN == cmd) + { + pgm = _consts; + send = 3; + } + + else if (STK_LOAD_ADDRESS == cmd) + { + address = *((u16*)packet); // word addresses + address += address; + } + + else if (STK_PROG_PAGE == cmd) + { + Program(CDC_RX,address,packet[1]); + } + + else if (STK_READ_PAGE == cmd) + { + send = packet[1]; + pgm = (const u8*)address; + address += send; // not sure of this is required + } + + // Check sync + if (getch() != ' ') + break; + Transfer(CDC_TX,&_inSync,1); + + // Send result + if (send) + Transfer(CDC_TX|TRANSFER_PGM,pgm,send); // All from pgm memory + + // Send ok + Transfer(CDC_TX|TRANSFER_RELEASE,&_ok,1); + + if (cmd == 'Q') + break; + } + _ejected = 1; + } +} + +// Nice breathing LED indicates we are in the firmware +u16 _pulse; +void LEDPulse() +{ + _pulse++; + u8 p = _pulse >> 8; + if (p > 127) + p = 255-p; + p += p; + if (((u8)_pulse) > p) + LED0; + else + LED1; +} + +void Reboot() +{ + UDCON = 1; // Detatch USB + UDIEN = 0; + asm volatile ( // Reset vector to run firmware + "clr r30\n" + "clr r31\n" + "ijmp\n" + ::); +} |